Used Plaster Worm for sale (384)

Condition: good (used), Year of construction: 1996, operating hours: 62,590 h, screw conveyor diameter: 50 mm, screw conveyor length: 1,300 mm, Make:KRAUSS-MAFFEI Description: used type: KMD-2-50-KK output capacity: max. approx. 140-180 kg/h for H-PVC pipes, depending on material and product this can vary year of construction:1996 Screw diameter:50-103 mm (conical) Screw length:1300 mm Screw speed: max. 43 m/min. Drive motor: DC motor 25 kW Cylinder heating/cooling zones: 4/3 (oil cooling) Dcsdpfxoh Nmt Do Aiisp inlet piece heating zone: 1 tool heating zones: 5 Equipment: dosing unit with hopper, vacuum pump for barrel degassing, barrel cooling unit, screw tempering unit Gearbox, was installed at 53,000 hrs. Overhauled worms and the cylinder Note: current running time is 62,590 hrs. Good Second hand functional

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 530 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. Djdpezz Rpcofx Aiiecp - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Condition: used, Year of construction: 2019, functionality: unexamined, machine/vehicle number: S40-0051, type of input current: three-phase, input voltage: 400 V, working width: 3,210 mm, cutting width (max.): 3,210 mm, laser power: 400 W, type of cooling: water, laser type: CO₂ laser, laser source model: Firestar f400, Equipment: fume extraction, The system consists of: Trotec SP4000 C / New Textile – 400 W CO₂ laser cutting system Sigma C13 – Cooling unit for the laser system Aigner VENT Set SP 3000 – Extraction and ventilation unit ASCO BV – Unwinding and material feed system for roll goods JQS Querimat QSV – Cross-cutting unit with a cutting width of 2,500 mm Dedpfezuyg Rsx Aiiscp Firestar – CO₂ laser source The system is currently located in Worms and was used in ongoing production until the plant was shut down. Since the machine is currently not connected to the power grid, a current functional test cannot be performed at this time. An on-site inspection is possible by arrangement. The system is offered in its current condition and with the components shown in the pictures.

Condition: excellent (used), Year of construction: 2021, ADLER K 750 – 270 cm Sweeper Attachment for Wheel loader mounting Year of manufacture: 2021 Working width: 270 cm Dsdpfx Aiezici Roiecp Hopper capacity: 240 liters Voltage: 12 V In good, fully operational working condition.

Condition: excellent (used), For sale: a SEW-Eurodrive WA20DT63L4/B03 worm gear motor with a 0.25 kW three-phase motor. The unit is fully functional, tested, and ready for operation. The gear motor is in good technical and visual condition. It shows normal signs of use, as visible in the photos. A power cable with a plug is included. Technical specifications: Manufacturer: SEW-Eurodrive Model: WA20DT63L4/B03 Dodpfx Aisz Sngmoiscp Motor power: 0.25 kW Power supply: 3× 230/400 V, 50 Hz Motor speed: 1300 rpm Output speed: 130 rpm Gear ratio: i = 10.25 Output torque: 16 Nm Protection class: IP54 Insulation class: B Operating mode: S1 Brake: 230 V AC Weight: 10.55 kg Manufacturer: SEW-Eurodrive, Germany The scope of sale includes exactly what is shown in the photos.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 531 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. Dcjdjz Agv Ujpfx Aiijp - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 532 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. Dodpfx Aijz Agw Eeiocp - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 533 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity Djdpez Ag Rrefx Aiiscp - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Condition: used, Year of construction: 2020, Overview Krones Ergomodul modular container labeller. Containers run anticlockwise after the infeed in a frontal arrangement with two discharge starwheels. Finish RAL 9018 papyrus white in the wet-line section. Two docking positions at the carrousel, both in operation, accept the four labelling stations without tools, so cold-glue and self-adhesive labelling run on the same carrousel; height adjustment of the top part and each station is motorised with container type preselection. Technical data - Manufacturer: Krones - Model: Ergomodul - Year of manufacture: 2020 - Table pitch diameter: 1,200 mm - Rotary plates: 30 - Machine pitch: 125.6 mm - Main drive: controlled servo motor; Danfoss servo motors, container table - Cold-glue stations (2x): ERGOMATIC-CL, 8-shaft glue pallet carrousel, 8-section gripper cylinder d = 350 mm, unwinding length 40-130 mm, steel glue roller, integrated glue pump, gluing height 5-215 mm, housing stainless steel, AISI 304-similar - Self-adhesive stations (2x): AUTOCOL-TS 120, web speed 120 m/min, supply tolerance +/- 0.5 mm, four-axis stand (application height, container diameter, conicity, sloping position), two-reel holder with automatic splicing and end-of-reel detection, driven carrier-film rewinder, ionisation unit, reels up to 390 mm outer diameter, carrier film up to 150 mm - Container infeed: worm with servo drive; detects damaged and fallen-over containers - Container orientation: prepared for camera orientation at the carrousel (360-degree monitoring, one camera); electrical interface prepared, mechanical adjustment unit not installed Dsdpfx Aszzz N Hsiiscp - Coding: prepared for a laser coder at the carrousel, with laser guarding, safety switch, clock pulse, oil-free air supply - Conveyors: flat-top chain, 83.8 mm wide, stainless steel (AISI 304-similar); servo-driven infeed, PM-motor discharge, centralised frequency inverter control - Machine guarding: lifting doors at the carrousel (polycarbonate), hinged doors at the front table (tempered safety glass) - Pneumatics: Festo; Bosch-Aventics, Norgren Herion, SMC, Bürkert components - Electrical: 400/230 V, AC 3/N/PE, 50 Hz, 28 A full load, 50 A back-up fuse; UPS 400/230 V, 17 A - Media: 92.4 m³/h oil-free compressed air, 0.009 m³/h process water - Weight: approx. 10,600 kg total (carrousel 3,200 kg, front table 3,000 kg, 1,100 kg per cold-glue station, control cabinet 1,000 kg) Equipment - 2x ERGOMATIC-CL cold-glue labelling stations, interchangeable - 2x AUTOCOL-TS self-adhesive labelling stations, interchangeable - Stand-alone control cabinet with Krones iPanel operator terminal - Central lubrication (Lincoln progressive distributor with motor pump) - Ecopush rejection module - Handling parts set on trolleys The inspection unit (Checkmat) and the container coding device used with this labeller are not part of this machine. Condition Used, still installed and under power in an operating line; on-site inspection possible before purchase. Availability Available now. The machine is in Belgium and will be dismantled and moved to our location in Germany; dismantling, loading and transport quoted on request.

Condition: used, Screw for C250-CFD Dcodpfx Ajzzcdfsiisp

Condition: used, Year of construction: 2011, workpiece diameter 320 mm threading length 570 mm Dcedpfxot Hxbdo Aiiep thread pitch 315 mm total power requirement 17 kW weight of the machine ca. 12 t dimensions of the machine ca. m

Condition: used, cutting diameter 470 mm saw band length 6.060 mm capacity 90 degrees: square 610 x 410 mm capacity 45 degrees: round 475 mm capacity 45 degrees: square 490 x 415 mm capacity 60 degrees: round 330 mm capacity 60 degrees: square 320 x 410 mm diameter min. 10.0 mm turning speed range: 20 - 100 m/min dimensions of saw-band 6060 x 34 x 1.1 mm height of material-table 810 mm total power requirement 5.5 kW weight 2080 kg range L-W-H 3280 x 1760 x 2010 mm Current new price ~ 55.000 euros Special price upon request Features: - Robust semi-automatic electro-hydraulic band saw - Miter cuts from -60° (left) to +60° (right) - Designed for industrial use - Ideally suited for cutting solid material - Extremely stable and robust construction - Cast-iron pulleys with a diameter of 500 mm - Equipped as standard with infinitely variable band speed adjustment - Microswitches control the highest and lowest positions of the saw arm - Includes a driven cleaning brush for optimal cleaning . and maintenance of the saw blade - Fully hydraulic system controls the machine's operating sequences - Cooling system provided at the saw blade guides - Blade guides equipped with adjustable carbide inserts - Machine drive features a low-maintenance, oil-lubricated worm gear - Powered by a robust three-phase motor - Motor equipped with overload protection - Machine frame consists of a highly solid steel construction - Features a solid, precise dual-column guide system - Linear guides on both columns ensure perfect cutting results - Includes cutting height limitation Dcedpe Ah Idpjfx Aiiep - Vise clamping jaw equipped with a long-stroke cylinder - Operating manual in German (PDF)

Condition: good (used), Year of construction: 2002, workpiece dia. 40 mm max. module 2 min. module 0,1 workpiece length - max. 665 mm weight 4,5 t spindle bore diameter 30 mm Dcedsv Ucdvspfx Aiiep Control Siemens dia. of cutter bearing 20 mm total power requirement 5,5 kW Technical data max. module 2 Pitch 0.5 - 25 mm Number of speeds multi-speed / multiple max. workpiece diameter40 mm max. workpiece length180 mm Milling cutter diameter max.80 mm max. milling cutter width12 mm Z-axis (milling length with counter point)90 mm Z-axis (milling length without counter point)113 mm Milling head swivelling angle30° / 30° Description Gear hobbing and thread cutting machine. LAMBERT - 124 CNC The machine is in a well-maintained condition.

Condition: used, Perfectly working grinding machine "станка 3Л722" Basic parameters Accuracy class A Maximum workpiece dimensions (length x width x height) 1250 x 400 x 400 Maximum dimensions on electromagnet 1250 x 400 x 280 Minimum dimensions on electromagnet 50 x 40 x 3 Distance from the spindle axis to the table mirror mm 210..625 Maximum product weight kg 600 Maximum weight on electromagnet 400 Machine work table Dimensions of table work surface (length x width) 1000 x 400 Table feed speed 3..35 Dcjdpfeqwzt Nex Aiiep Grinding head Dimensions of grinding wheel ПП450х80х203 Grinding wheel speed/min 1460 Maximum grinding speed m/s 34.4 Maximum diametrical feed, mm 430 Accelerated transverse disc feed m/min 1,2 Automatic cross feed for each table feed mm/rev 1..60 Maximum vertical disc feed, mm 415 ?? 0,002 ?? 0,2 Automatic vertical disc advance, mm 0,002..0,128 Vertical accelerated advance speed, m/min 0,2 Electrical equipment Number of motors 13 Disc spindle motor power, kW 11 Hydrostatic pump motor power 4 Hydrostation air heat exchanger motor power 0,09 Lubrication system pump power 0,25 If you have any further questions, we will be happy to answer them.

Condition: excellent (used), functionality: fully functional, The dividing head is equipped with an SK40 spindle and has a spindle bore of 25mm. It can be swiveled from right to left up to 90° each. The dividing head spindle can be tilted 6°/15° from and towards the machine. It is suitable for all Deckel FP series milling machines and their "licensed machines," such as the Macmon M100. The distance from the spindle axis to the tailstock guide is 100mm. Direct division is possible using a 360° division circle or 24 x 15° indexing. The distance from the dividing head center to the tailstock center is 400mm. Indirect division is achieved with a worm gear of 40:1, using a scale disk with 1' division or three different hole disks (A: 27; 31; 34; 41; 43 – B: 33; 38; 39; 42; 46 – C: 36; 37; 40; 58). Also included are a Röhm four-jaw chuck, a three-jaw chuck (possibly Röhm) with adapter rings, and a two-jaw chuck, as well as a tailstock with a tailstock bearing. The dividing head, which was originally non-functional, along with all accessories, has been disassembled into individual parts, refurbished, made fully functional, and painted in two colors (RAL 7035 light gray / RAL 5004 dark blue). The dividing head is not in use and can be delivered immediately. Minor signs of wear from previous use are visible to a small extent. Dcodpsz Hyyfefx Aiijp A single-use transport crate, with a total weight of 109 kg, has been prepared for transport. A manual compiled from Deckel descriptions is also included in the scope of delivery.

Condition: ready for operation (used), * Brand: Radicon Dcjdpfoywmaxox Aiiep * Model: worm gear uits * Type: BU 12 * Ratio: 30 : 1

Condition: excellent (used), Year of construction: 2009, Technical Data Machining: 5 axes: 3+2 Travel distances X / Y / Z: 300 / (300 + 100) / 330 mm Spindle speed max.: 24,000 min-1 Control system: FANUC Series 31i-MODEL A5 Tool magazine: 21 positions Rapid traverse X / Y / Z: 54 m/min Table load, base machine: max. 200 kg, evenly distributed Tool length max.: 190 mm; Ø40 mm in the range of 120–190 mm Tool diameter at 150–12,000 min-1: 80 mm Tool diameter at 12,000–15,000 min-1: 60 mm Tool diameter at 15,000–20,000 min-1: 45 mm Tool diameter at 20,000–24,000 min-1: 40 mm Peiseler indexing head: AWUP, pneumatic clamping up to 6 bar Peiseler: Faceplate speed max.: 55 min-1 Peiseler: Tangential torque during circular milling max.: 250 Nm Peiseler: Transport load, faceplate vertical: 150 kg Peiseler: Tilting moment: 1200 Nm Peiseler: Tangential torque clamped (6 bar): 500 Nm Peiseler: Center bore: 50 H7 mm Peiseler: Faceplate runout: 0.01 mm Peiseler: Center bore runout: ±0.01 mm Peiseler: Positional accuracy from worm gear: ±15 arcseconds Connection, weight and dimensions Tool weight / total tool weight: 2 / 23 kg Machine weight: 2050 kg Electrical connection: 3 phases, 200/220 V, 50/60 Hz Connected power: 10 kVA Equipment and scope of delivery Peiseler AWUP swivel/indexing head for 3+2-axis machining Elbaron electrostatic filter, documentation RONA 60 SV Renishaw OMP40-2 measuring probe Blum measuring probe in the work area Extinguishing system according to the photos Djdpfxe Aba Ife Aiijcp Technical specifications are subject to change without notice. Errors and prior sale reserved. The properties agreed upon in the purchase contract and the agreed scope of delivery shall apply.

Condition: new, Year of construction: 2026, Putz P4 cement For on-site preparation of plasters CEMENT, SAND, LIME Pump motor 5.5 kw Mixer motor 2,2 kw 55/min Capacity for 2L6 pump approx. 25 l/min Capacity for 2L6 pump +++ 45 l/min Compressor 350 l/m Tank capacity 130 l Mixer capacity 130 l Height to mixer 118 cm Height to pump tank 71 cm Width of pump tank 64 cm Length without shoe 165 cm Weight 360 kg Included Working hose Air hose Dcodpfx Aetuiqyeiiep Spray gun Hose cleaning ball Shneka 2L6

Condition: excellent (used), For Sale: Silomat Pneumatic Conveying Systems / Silo Pumps (Gravity & Pressure Types) We offer a wide range of Silomat conveying systems from various brands for sale, available in both gravity (free-fall type) and pressure configurations. All units have been completely OVERHAULED and professionally reconditioned: Oil replacement New composite vanes New bearings Professionally sandblasted and fully painted The machines are ready for operation and available for purchase either with brand-new accessories or without. Dcsdelf Niqopfx Aiiep Available Gravity / Free-Fall Models (approx. 40 units in stock): PFT E100L MALTECH MB100 M-TEC F100E Contact us for more details, pricing, and available configurations.

Condition: used, Year of construction: 2023, Overview This Gernep Soluta 6-720 2SK SD is a rotary self-adhesive labelling machine built in 2023. It carries two self-adhesive labelling stations on a 720 mm container table with twelve servo-driven bottle plates, and runs at a rated output of 11,000 bottles per hour with an adjustable range of 2,000 to 12,000 bottles per hour. Containers are fed in through a single infeed worm and an eight-division star, held on servo-driven bottle plates while the labels are applied, and discharged through the same star pitch. Height adjustment is electric, the labelling stations and the bottle-plate drive are servo-controlled, and the machine is operated from a touch panel with a free-standing control cabinet. Broken-container detection is fitted, and a VPN router for remote maintenance is installed. Technical data - Manufacturer: Gernep - Model: Soluta 6-720 2SK SD - Year of manufacture: 2023 - Machine type: rotary self-adhesive labeller - Rated output: 11,000 bottles/h - Adjustable range: 2,000 - 12,000 bottles/h - Container table diameter: 720 mm - Container plates: 12 - Pitch: 188.4 mm - Infeed/discharge star: 480 mm diameter, 8 divisions - Self-adhesive labelling stations: 2 - Labelling station drive: servo - Container plate drive: servo - Main drive: asynchronous - Infeed worm: single worm, mechanical drive - Height adjustment: electric - Running direction: left-hand machine - Installation variant: linear - Pneumatics: Festo Bottle formats Built for two glass bottle formats, each at 11,000 bottles per hour: - Glass bottle, 250 mm high, 75 mm diameter - Glass bottle, 215 mm high, 65 mm diameter - Labels on both formats: paper body label 110 x 75 mm, paper back label 50 x 75 mm Equipment - Two self-adhesive labelling stations - Touch panel operation, free-standing control cabinet, swivel arm - Frequency converter Dcedpfx Aisz Dimpsiep - Broken-container detection - Remote maintenance including VPN router - Prepared for dating and coding - Prepared for optical orientation - Format parts included: one infeed worm, one infeed/discharge star, one set of container plates, one set of centring bells Not fitted: label inspection, mechanical orientation. Condition The machine is set up and under power and can be inspected by arrangement. Availability Immediately available.

Condition: used, Year of construction: 2006, Manufacturer: Seydelmann Model: AV250 Year: 2006 Condition: Used Serial number: 06089-1 Stock number: 2914 Plate diameter: 250 mm Hopper: 800 liters Power: 3 x 400V, 50Hz, 78kW Dimensions: 1650 x 1700 x 2400 mm Weight: 1750 kg Dcsdpfx Aoz S H S Tsiiep 3 speeds on the feed screw, 2 speeds on the working worm.

Condition: excellent (used), Year of construction: 2016, Cutting Capacity 0° round (tube): 300 mm Cutting Capacity 0° round (solid material): 180 mm Cutting Capacity 0° rectangular horizontal (hollow section): 320 x 290 mm Cutting Capacity 0° bundle (tube): 320 x 160 mm Cutting Capacity -45° round (tube): 300 mm Cutting Capacity -45° round (solid material): 110 mm Cutting Capacity -45° rectangular horizontal (hollow section): 300 x 280 mm Cutting Capacity -60° round (tube): 200 mm Cutting Capacity -60° round (solid material): 80 mm Cutting Capacity -60° rectangular horizontal (hollow section): 190 x 200 mm Cutting Capacity +45° round (tube): 270 mm Cutting Capacity +45° round (solid material): 110 mm Dsdpoxz Dqmefx Aiijcp Cutting Capacity +45° rectangular horizontal (hollow section): 270 x 200 mm Table height, material feed: 800 mm Main motor: 2.6 kW Cutting speed, stepless: 20 - 100 m/min Saw blade size: 3660 x 27 x 0.9 mm Machine dimensions (L x W x H): approx. 1800 x 950 x 1400 mm Net weight: 585 kg Accessories / Special features: • Semi-automatic swing-frame metal band saw • After the cutting cycle is started, the vice clamps automatically – after completion, it returns to its starting position • For mitre cuts from +60° to -45° with frequency inverter • Suitable for cutting stainless steel, tool steel, hollow profiles, and solid materials • Fully hydraulically controlled sawing functions • Saw drive with low-maintenance, oil-lubricated worm gear • Robust three-phase motor • Motor equipped with overload protection • Ball-bearing turntable • Saw arm inclined at 25°, resulting in longer saw blade service life • Saw arm swivels from +60° to -45° • Chip removal brush for optimal saw blade cleaning and maintenance • Frequency inverter: allows stepless adjustment of saw blade speed from 20 - 100 m/min • BRP – Saw band monitoring • Hydraulic vice with manual quick-release for lateral adjustment • Limit switches control upper and lower saw arm positions • No need to set the upper end point • Length stop with scale, left-side removal 3 m • Cut detector • Swivelling control panel • Micro-spray device • 2 x roller conveyors: 3 m discharge left, 6 m feed right • CE compliant Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: PA12704, 110610702, PA12707, mobility: mobile, Badeer Fish Grading Machine – full documentation available in both Polish and English. The onboard computer operates on the MES - B'Logic software platform. It includes two modules: B'Logic Grading and a label design software B'Logic. The set includes: - CAB label printer - Feed hopper - Acceleration conveyor - Weighing machine - Sorting conveyor - PC computer The computer located next to the label printer at the machine is touchscreen. The main computer for setting product specifications (for the currently processed product) does not need to be positioned near the machine. Specification: - 100–120 fish per minute - Maximum fish size: Length – 350 mm, Width – 220 mm - Operating speed adjustable by user (as shown in the video) - Airborne noise: < 70 dB Machine dimensions: Grading section: Height: 1.3 m, Length: 4.417 m, Width: 1.050 m Conveyor belt width: 60.8 cm (S 800 seamless belt) Power consumption: 0.37 kW Steel quality: AISI 304 Motor: Worm gear drive Feed hopper: Height: 1.87 m, Length: 3.66 m, Width: 1.5 m Conveyor belt width: 45.6 cm Drum motor Power consumption: 0.37 kW Dynamic weigher: Belt width: 250/350 mm Product weight: up to 1 kg (possible calibration) Dcodpfx Aiey Hiyajisp Motor power: 0.18 kW Speed: 0.25 mm/s – 2.0 mm/s

Condition: excellent (used), Year of construction: 2019, Geared motor, electric motor, electric geared motor, worm geared motor, flat geared motor -Condition: Geared motor is unused -Manufacturer: NORD DRIVESYSTEMS, Flat gearbox series F -Type: SK7382AZH-180MP/4 TF Dcedpfx Aiszu S Hpjiop -Speed: 22 rpm -Power: 18.5 kW -Protection rating: IP55 -Hollow shaft: Ø 70 mm -Dimensions: 930/450/H660 mm -Weight: 410 kg

Condition: excellent (used), functionality: fully functional, overall weight: 60 kg, total height: 175 mm, jaw width: 200 mm, total length: 615 mm, total width: 200 mm, jaw height: 60 mm, clamping width: 200 mm, clamping range: 435 mm, Equipment: type plate available, Allmatic-NC machine vice, high-pressure clamping device Type LC 200 including a second pair of clamping jaws, width 200 mm Jaw width 200 mm Base body, type LC 160/200 (for jaw widths of 160 and 200) Base body width 164 mm Clamping force adjustable, max. 60 kN Level 0: direct Level 1: 15 kN Level 2: 30 kN Level 3: 45 kN Level 4: 60 kN Clamping range a: 0-250 mm Clamping range b: 189 – 435 mm Jaw height 60 mm Base body length 530 mm Overall length 615 mm Base body height 115 mm Weight 60 kg Used, in good condition optional: Clamping jaws, width 160 mm, height 50 mm, new € 200.00 Dsdpfx Aozfimuoiijcp Aluminum jaws, width 200, height 60 mm, height 80 mm, new € 200.00 Worm gear € 100.00