Used Pellet Maker for sale (465)

Condition: refurbished (used), Year of construction: 2012, operating hours: 1,000 h, functionality: fully functional, overall weight: 100,000 kg, Pellet production line of Italian manufacture. Renown brands of machinery like General Dies SRL, Miller SRL, FIDA SRL and other brands. Capacity of the line 1.3 tons per hour Pellet press General Dies TAU4 – 110kw Container with movable floor and hydraulic power aggregate Triple-Pass rotary drum dryer 2.5 tons catalog capacity (effective capacity up to 1.5 tons/hour) Transport divider for biomass separation Pezzolato PTH 660/700 (Wood chipper, possibly excepted from the line if buyer wishes so) Furnace for rotary drum dryer and complementary equipment Hammer mill “Miller SRL” 75 kw Transport conveyors for biomass transport Cyclon for dust removal Cooler silo for dust removal Hodpfx Aei Akrkjhgst Weighing and packing equipment Electric cabinets for the entire line with cables Ventilation tubes for sawdust and wood chips transport Screw air compressor 860l Pump for grease dozing in central press lubrication system Included are additional pieces of equipment like filter silo bags, metal connections etc. (complete line is between 4 and 5 full trucks of equipment)

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, total length: 69,000 mm, total width: 16,000 mm, total height: 16,000 mm, The system was designed according to Eurocode EN 1993 for the industrial drying of wood chips, sawdust, or similar biomass products and is suitable for use in biomass, wood, or pellet production. Hedpfx Ahszw Apgjgst Process components: Air heater, deflection rollers, feed modules, discharge modules, trough chain conveyor, belt tensioning and adjustment device, 7 exhaust stacks (height up to approx. 17.6 m) Designed for hot air or waste heat utilization (e.g., biomass boiler or CHP plant), heat requirement 10,270 kW th, installed electrical power 690 kW el. The inlet temperature in the dryer is 68°C, the outlet temperature is 42°C, and the heat transfer medium is a water/glycol mixture. The volume flow at the dryer outlet is 1,081,000 m³/h. Dust emission value 5 mg/Nm³ (moist), sound pressure at a distance of 1 m 85 dB(A) from the opening of the exhaust duct and the dryer. The dryer is designed for an outside temperature down to -40°C, the conveying capacity is at least 70 m³/h and a maximum of 250 m³/h with a bulk density of 260 kg/m³. The working platform of the dryer is located on approximately 8.00 m high steel supports and is enclosed with thermally insulating sandwich panels. A hall or other production components can be inserted under and between the supports (see under Documents, Steel Structure). The system has been disassembled and stored by an experienced assembly team, and this team can be arranged for transport and reassembly. Please note: We are selling exclusively this belt dryer and no other parts! Please direct your inquiries via WhatsApp to Mr. Sörgel; he is on-site at the factory and may not always be available by phone. Thank you very much!

Condition: used, Year of construction: 2016, operating hours: 12,000 h, functionality: fully functional, The last service by Asco was performed in December 2016 at 12,032 operating hours. Since then, the machine has only run for an additional 603 hours due to an investment in a brand new production line. The machine’s total operating time is 12,635 hours (12,032 h at last service + 603 h extra use). • The machine comes with complete documentation, including technical manuals and service reports. • Both the pump and the cylinder have been replaced. ASCO’s automatic dry ice machine produces slices of varying thicknesses and two pellet sizes (3mm and 16mm) at the push of a button. The dies for the different sizes are integrated and selectable via the touchscreen—manual changeover is not required. Theoretical output is up to 400 kg/h, depending on the type of product (block thickness or pellet size). According to the owner, the machine consistently produces at least 250 to 300 kg/h in practical use. Hodpfx Ahey R I Uqjgst New price: €160,000. Worldwide shipping available. Relevant keywords for search and sale: Cold Jet dry ice machine for sale, dry ice blaster for sale, industrial dry ice cleaning machine, CO2 cleaning equipment, Cold Jet Aero series, used Cold Jet, second-hand dry ice blasting machine, dry ice pelletizer, cryogenic cleaning, high-pressure dry ice blaster, refurbished dry ice blaster, 20 ft blasting hose, dry ice gun, venturi nozzle, Kärcher Ice Blaster, ASCO Jet, Cryoblaster, ICS, Nozzitec, Triventek, Cryonomic, Südstrahl, White Lion, ICEsonic, industrial cleaning equipment Europe, dry ice machine export, DrDryice. Contact for more details or to arrange an inspection.

Year of construction: 2018, operating hours: 7,000 h, condition: used, functionality: fully functional, We are offering this used Himel / Gama control cabinet for a pellet press and pellet system for straw / hay / alfalfa, manufactured in 2018. It has approximately 7,000 operating hours. The hourly output, depending on the biomass, is 700 - 1200 kg, according to the manufacturer. We also have a separate press with 90 kW available for €95,000; it has approximately 500 operating hours and was manufactured in 2025. Type: Control cabinet for pellet press Number: 20182138 Year of manufacture: 2018 Power supply: TNC-S 400V AC/N/PE Frequency: 50 Hz Power: 195 kW Hsdpszrvh Eofx Ahget Max. current consumption: 375 A If you have any questions or need more information, please send us a message or call us.

Condition: good (used), CMC Q Cover Two LPA2 50-70 Hard Cover Maker The machine is in very good condition and ready for production. Made in Italy. Manufacturer’s description: The machine is very easy to set up, operate, and service. It can produce over 250 covers per hour. The machine is equipped with the following components: – a hot glue application module (laminator) with a roller steam extraction bar, – an assembly table with a vacuum system, – a module for folding the veneer edges in a single pass on both sides, – pressing rollers, – a module for positioning the cardboard, Veneer types that can be used: smooth and laminated paper, photo paper, canvas, artificial and genuine leather, etc. Technical specifications: Type: Semi-automatic machine for producing hardcovers Maximum cardboard format: 700 x 500 mm Maximum paper format (cover): 740 x 520 mm. Cardboard weight: 1.5-3.0 mm. Power consumption: 2 kW, Power supply: 380V. Adhesive type: hot or cold Hedpozw Tzgofx Ahgjt External dimensions: 140x210x125cm Weight: 490kg.

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Duplo 600 Bookletmaker Stitch/Fold and Trim. Year 2019 1 Owner from new. In full working order with video on request. Any further info, inspection get in touch. Machine located in UK Hsdpfjzmn Aqjx Ahgst Paper type: Fine quality paper: 64 to 160gsm Art/Coated paper: 84.9 to 160gsm Cover sheet: 350 gsm Paper Size Saddle stitching/Length: 170 to 640 mm Width: 105 to 364 mm Side and corner stitching: B5LEF, A4SEF/LEF, B4SEF/LEF Maximum processing speed A3 finished to A4: 4,100sets/h A4 finished to A5: 4,600sets/h Minimum size: 5,200sets/h Stitching Capacity No. of stitches: 0 to 2 Stitch thickness within:2.5mm Folding Capacity Below 25 sheets (81.4 gsm) Key Applications • Letter landscape booklets • Small size booklets • Calendars • Corporate Reports • Catalogs • Brochures • Yearbooks • Magazines

Year of construction: 2020, condition: used, functionality: limited functionality, We offer this technological line for pellet production from vegetable waste (sunflower husk) – BART-M SRL OGM 1.5, manufactured in 2020, in used condition. Manufacturer: BART-M SRL Model: OGM 1.5 Year of manufacture: 2020 Condition: used Hsdpfx Ahoztaahegjt Category: 34 Productivity: 800 kg/hour Weight kg: 6800 Dimensions mm Length: 5385 Width: 4400 Height (without exhaust pipes): 6935 Traction: electric Energy performance Total installed power kw: 150 Type of current: Alternating Current frequency hz: 50 Network voltage V: 220/380 Agrotechnical performance: Admissible amount of non-granulated raw material: 2% max Admissible moisture content of cooled granules: 12% max Technical characteristics of the finished product: Caloric value of the granules Mj/Kg: 14-19 (vegetable waste) Kw/kg: 3.89-5.27 Diameter mm: 6-8 Length mm: 40 If you have any further questions or need more information, please do not hesitate to send us a message or call us.

Condition: used, Year of construction: 2007, functionality: fully functional, power: 100 kW (135.96 HP), heating capacity: 100 kW (135.96 HP), nominal heat output: 100 kW (135.96 HP), nominal power: 100 kW (135.96 HP), tank capacity: 5,000 l, We are offering this used HDG Bavaria 100kW heating system with articulated arm discharge, manufactured in 2007. Manufacturer: HDG Bavaria Model: 100kW with articulated arm discharge Year of manufacture: 2007 Hjdpfjyrhd Tsx Ahgot If you have any questions or require further information, please feel free to send us a message or give us a call. The system is currently still in operation and can be inspected. The offer includes a 5,000L buffer tank, control unit, and various spare parts (which we have kept in stock as a precaution).

Condition: used, functionality: fully functional, For sale is a Gránit-Mill 90 pellet press in good condition, suitable for pellet production or use in the animal feed industry. The main components of the machine are: * Pre-hopper * Feeder screw * Permanent magnet * Conditioner * Press Hsdpfxozc Eude Ahget * Control cabinet Motors: * Pre-hopper motor: 1.1 kW * Feeder motor: 1.5 kW * Conditioner motor: 15 kW * Table motor: 0.55 kW * Main motor: 90 kW Accessories: * 2 stickers * 1 set of grooved rollers (total of 2) Additional information: The control cabinet was originally designed for the simultaneous operation of two presses, but it is also possible to control the presses separately. Price: * 1 Gránit-Mill 90 press with complete accessories and control cabinet: 29,000 EUR * When purchasing two presses together: 44,900 EUR The machines can be viewed at our location by prior arrangement. Further technical information, photos, and videos are available upon request.

Condition: good (used), Year of construction: 2018, Equipment: documentation/manual, MAAG M-USG 600 H – PET Pelletizing Line, 6,500 kg/h – 2018 MAAG Automatik M-USG 600 H pelletizing line, manufactured in 2018, designed as an underwater strand pelletizing system for the continuous production of polymer pellets and originally used for PET. The line integrates automatic strand feeding and cutting, water cooling, hydraulic conveying, centrifugal drying and pellet classification, with an approximate nominal capacity of 5,300 kg/h and a maximum design capacity of up to 6,500 kg/h. Hjdpszvc R Uefx Ahget Equipped with an 80-strand die head, automatic feeding system and strand pelletizer/cutter, hydraulic conveying system, MAAG CENTRO 1600 centrifugal dryer, exhaust fan, VIBRA Schultheis SRK 15/7.5-I-V-S vibrating screen, and control system with Siemens SIMATIC HMI. Predominantly stainless-steel construction in the areas in contact with the product and process water. Suitable for PET pellet production and potentially for recycled PET (rPET) pelletizing applications, subject to process configuration and material characteristics. Two identical lines available, fitted with MAAG CENTRO 1600 dryers, machine numbers CE-0468 and CE-0469.

Condition: excellent (used), Year of construction: 2023, operating hours: 368 h, functionality: fully functional, Pellet Plant EcoKraft LP22 – Complete Line with Bagging System – Year 2023/2024 For sale is an as-new pellet production plant consisting of two EcoKraft LP22 pelletizing lines including shredding, drying/extraction, screening, big bag system, and a semi-automatic bagging unit. Year of manufacture: Q4/2023 Commissioning: Q1/2024 Operating hours: Pellet press 1: 368 h Pellet press 2: 126 h Scope of supply: 1x Hacker HA1100 (22/30 kW) 1x Cutting mill SMC 500/700 (37 kW) Hodjynzcuepfx Ahget 1x Extraction & filtration unit SMU60 2x Material bunkers MB3LPS (each 3 m³) 2x Dosing systems DS25 2x Pellet presses LP22 (each 24 kW) 2x Screening units with conveyor belt 20x Big bags incl. frame 1x Semi-automatic bagging unit AS900 (400 g – 60 kg, calibration-ready) Special features: ✔ Fully interlinked system ✔ Integrated metal separator ✔ Temperature monitoring & central lubrication ✔ Both big bag and sack filling possible ✔ Very low wear / few operating hours ✔ New price: €577,138 net Sale price: €395,000 net Including assembly, transport, commissioning, UVV (accident prevention regulation), risk assessment, and operator training—only within Germany, Switzerland, and Austria. Viewing by appointment possible.

Condition: excellent (used), Year of construction: 2011, Ref:11134 . 2011 Hoerauf BDM ‘Universal’ Case Maker For short, medium and long runs with the shortest set-up time and the widest open case format. Suitable for 3-piece cases, game boards, padded cases for photo albums, pocket diaries, bible cases etc. Comprising: LCD Screen for menu guided set-up and fault display. Conveyor feed of pre-cut boards Triple reel feeder for soft spines with auto-splice Magazine feeder for stiff or hollow spines Shingle conveyor feed of pre-cut cloth Pre-melt tank Mobile hot-melt gluing unit and circulation pump Delivery with counter and roller table DC drive motor Complete with compressor, tools & accessories. Note: External compressed air supply - 6 bar required (not included). Hsdpfx Aeztvg Dehgjt Specification: Open case size standard : Max. 410 x 720 mm, Min. 105 x 170 mm Board thickness : Max. 4 mm, Min. 1 mm Spine width : Max. 90 mm, Min. 6 mm Spine thickness, flexible : Max 0.6 mm, Min 0.3 mm Rigid : Max. 3 mm, Min 1 mm Cover material : Max. 0.3 mm, Min 0.1 mm Mechanical speed : Max. 60/min.

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase Hsdpszvq Rcjfx Ahgjt • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price: 35 000 EUR (VAT is not included)

Condition: like new (used), Year of construction: 2024, Pellet production plant – complete line – fully automated Salmatec press Hsdpfxszg Eudo Ahget Rematec hammer mill Belt dryer VAI bagging machine Cooler Sifter Palletizer Less than 1000 operating hours – certified Option for on-site reinstallation Option for on-site operator training

Condition: excellent (used), Year of construction: 2016, Ref: 11137 . 2016 Horizon SPF-200L Latest model, high speed, fully automated booklet maker with A4 landscape format capability With additional trimmer for 3 sided cutting! Features: Advanced Automation – All necessary settings for a wide variety of booklet formats can be performed automatically. Even the fold roller gap adjustment is automated so very quick changeover with minimal test sheets. 10.4’’ large colour touchscreen with icon-based display for easy operation Cost Savings –works with pre-cut 4-page sheets instead of folded signatures to eliminate the folding process. Equipped with: 3 x Horizon VAC-600Ha+m+c towers (18 Bins) PJ-77R Jogger delivery for rear collation off C tower IFU-200 connecting unit SPF 200L Stitcher and folder 2 x 43/6-S Hohner Stitching heads FC 200L Foredge trimmer TBC-200L Top and bottom trimmer Waste paper removing conveyor PK-30 kicker LC-200 delivery Specification: Sheet Size: Max. 356 x 610 mm or 14.000” x 24.000” Min. 120 x 180 mm or 4.725” x 7.090” Sheet Weight Range: Normal Paper: 64 to 157 gsm Art Coated Paper: 84.9 to 157 gsm Stitch Thickness: Top/Side Stitch, Corner Stitch and Fold Max. 4 mmor 0.155” (About 48 sheets of normal paper 64 gsm) Production Speed: Max. 4,000 booklets per hour (A4-Finish, Portrait) Hedpfx Aezuth Ishget Max. 3,500 booklets per hour(A4-Finish, Landscape)

Year of construction: 2012, operating hours: 3,500 h, condition: used, functionality: fully functional, P System fully automated hydraulic pelleting line with patented hydraulic pelleting system. Mono roller, hydraulically operated with a unique load sensing system. Features automatic vegetable oil injection at startup and shutdown. Continuous rated production 350kg/hr (peak 500kg/hr) - Fully automatic, operates without human intervention. In its current setting it worked 12hrs continuously alongside log production, but can operate continuously if required. Line includes the following:- 50m³ moving floor container with hydraulic operated lid. Material level viewing windows, and unloading cross auger. Incline discharge auger with magnetic separator. First stage hammer mill for material up to P16 (G30). Pneumatically conveyed to minisolo. Mini silo distribution hub with hydraulic agitator. Equipped with cyclone and transfer fan. The unit has an additional port covered with a blanking plate to allow addition of another pelleting module. Second stage hammer mill and rotary valve controlled by pelleting module. P300 - 30kW pelleting module with PCL control system. All motors other than the main drive are hydraulic and controlled by the pelleting module. The system has a moisture sensor which injects water into the second stage hammer mill to control pellet quality. Die temperature is monitored by a temperature probe and controlled by compressed air injection. Automatic oiling system on startup and shutdown. 6m Discharge cooling and screening auger. Pellets are conveyed, cooled and screened for dust by hydraulically driven auger. Double filter air extraction unit. The line is in good condition and comes with a set of spare parts, dies and rollers. PCL control unit and main drive gearbox were replaced over a year ago. It has been serviced well and can be demonstrated working if required, with your material. Hodpfszcf Dlox Ahgst Not included in offer, but available by request 4000L pellet hopper made from galvanised steel metal, with pneumatically operated hopper. Semi-automatic bagging plant, 5kg - 30kg capacity. Plastic sack heat sealer. Pellet quality test equipment. 5m Bucket elevator made by Perrys of Oakley.

Year of construction: 2013, operating hours: 7,700 h, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 12090, This is a recycling extruder with side feeding for materials (flakes, pellets, etc.). The system is supplied with a control cabinet and a double vacuum system. The pelletizing system is missing at the end of the screw – it is not included in the scope of supply. The cylinder ends at the flange. The extruder is supplied without a screw. The frequency inverter for the main motor was replaced with a new unit 3 years ago. Installed power approx.: 474 kW Cooling water requirement approx.: 190 l/min Fresh water consumption approx.: 110 l/h Feeding system: • Diameter of the feeding screw: 200 mm • Drive for the feeding screw: 45 kW, frequency-controlled • Hopper capacity net 7 m³/250 ft³, • Gear motor 3 × 3 kW • 2 sight glasses in the hopper • 2 level indicators Extruder: • Diameter of the extruder screw: 145 mm • L/D ratio: 24 • Heating power: 50 kW • Extruder drive unit 280 kW Vacuum 1: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 11 kW • Vacuum capacity: 225 m³/h • Vacuum pressure: 33 mbar Vacuum 2: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 7.5 kW • Vacuum capacity: 190 m³/h • Vacuum pressure: 33 mbar Cylinder: • Cylinder: Bimetal extruder cylinder, • Reinforcement layer 1.8–2.0 mm thick, • Hardness 63–65 HRC Installation conditions: • Voltage: 3 × 400 Volts • Permissible fluctuation max.: +5 % – 5 % • Frequency: 50 Hz Permissible fluctuation max.: +4 % – 4 % • Protective measure: Multiple grounding • Ambient temperature: min. 15 °C, max. 35 °C • Humidity max.: 90 % • Altitude of the installation site: 0 – 1000 m The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center is being closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price is without packaging. Hjdpfxeznz Ezo Ahgot

Condition: good (used), Horizon VAC-100a + VAC-100c + SPF-20 + FC-20 Booklet Maker The machine is in very good condition, well-maintained, and ready to work. Made in Japan. The line consists of: – Horizon VAC-100a / VAC-100c Max size: 350x500mm Min size: 120x148mm Vacuum feeding 10 shelves Stack height: 55mm Basic weight: 40-270g 230V power supply Weight: 310kg/piece Touchscreen control Jam, double-feed, and no-feed sensors Ability to save 9 preset jobs to the machine’s memory Horizon SPF-20 Max size: 500x350mm Min size: 120x180mm Wire stitching Folding Two Hohner heads (max. 4) 230V power supply Weight: 490kg Hjdszur A Repfx Ahget Horizon FC-20 Cutting capacity: 88 sheets 230V power supply Weight: 240 kg The machine includes: an LC-20 delivery system, additional EAB-100 compressors, a PK-20 packaging kit, a PJ-75 jogging system, operating tools, spare parts, and full documentation with parts catalogs.

Year of construction: 2014, condition: excellent (used), functionality: fully functional, We offer this pellet production line from STOZA s.r.o., in very good condition, year of manufacture 2014. Hodpfx Ahjy Ah Nfeget Manufacturer: STOZA s.r.o. Year of manufacture: 2014 Condition: very good Category ID: 659 Type: Pellet production line If you have any questions or need further information, please feel free to send us a message or call us.

Condition: ready for operation (used), functionality: fully functional, suction capacity: 20,000 m³/h, production capacity: 1,300 unit/h, No minimum price – guaranteed sale to the highest bidder! The hammer mill (year of manufacture 2021) has only approximately 2 operating hours! The system is suitable for straw, hay, alfalfa, compost, wood, and other agricultural raw materials! TECHNICAL DETAILS Capacity (material-dependent) max.: 1,300 kg/h MACHINE DETAILS Hammer mill power: 75 kW Pellet press: 75 kW, without control unit Bale shredder: 35 kW, including control unit Dust filter capacity: 20,000 m³/h, including control unit Operating hours Entire line: approx. 1,500 h Hammer mill: approx. 2 h EQUIPMENT Pellet press Conveyor belt Elevator Pellet cooler with screen Buffer tank with discharge 2 cyclones with rotary valve airlock Fan for cooler extraction New die Various used spare parts 10 m feed table for the bale shredder Bale shredder, including control unit Hammer mill, including control unit Centrifugal separator Big bag station for dust filter Dust separation technology: EU-ATEX Directive 2014/34 Positive dust explosion assessment from 2023 Hjdpfjzgf A Ujx Ahgot Note: The line has already been dismantled and is ready for loading.

Condition: used, Year of construction: 2011, functionality: fully functional, SEMI AUTOMATIC CASE MAKER MACHINE Hedpfxew Inyte Ahgst DARIX EVOLUTION LIGHT

Condition: used, functionality: fully functional, Year of construction: 2015, Palletizer and pallet wrapper Capacity 100 kg / h Used, no warranty This machine is located in Tata, Hungary. What is Pellet? Pellets are a natural biofuel made from made from agricultural and forestry wastes, such as dried sawdust, compressed into small cylinders with a diameter of a few millimetres. It possible to obtain a compact product with no additives and chemicals. Benefits of pellets? Among the most important advantages: environmental sustainability (reduction of deforestation and GHG emissions); cheap to produce and affordable to buy. Hodpfjtw Szaox Ahgjt And, due to the pressing process, the calorific value of pellets is approximately double that of wood for the same volume.

Condition: reconditioned (used), functionality: fully functional, machine/vehicle number: Pal 1600, power: 180 kW (244.73 HP), input voltage: 380 V, warranty duration: 12 months, Equipment: documentation/manual, 1 pellet press brand: Paladin 1600-210 Hsdpjq U R N Tsfx Ahget inner diameter die 850 mm tread die 210 mm Press is equipped with 2 motors each 90 KW n=1500. Press door is made of stainless steel with overload valve in door. 3 Roll press with 3 rolls on the press overhauled in a drilled or racked version Press is complete with mold lifting device and tools The press is completely overhauled and equipped with new bearings and wear parts such as front and rear sliders die washer etc. Also new V-belts and toothed belt. Also, all safeties will be observed and appropriate switches on Friction safety , door switch and inspection hatches will be fitted. Refurbished pump unit for friction and V-belt tensioning Remark: Conditioner on the press is optional

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, power: 75 kW (101.97 HP), For sale: fully operational pellet production line. Hedjw Ry U Iepfx Ahgst

Condition: refurbished (used), Year of construction: 1992, functionality: fully functional, machine/vehicle number: 305.537.1992, warranty duration: 12 months, Le Meccanica CLM630ST 630/150 die and rolls Force Feeder with a 0.9KW motor Currently undergoing full refurbishment - Seals &bearings included Colour - customers option Hsdpfx Ahsv Sq Rleget Customer to arrange collection and freight