Used Marcelo Plank for sale (143)

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Bjdpfx Asi Ri Rvoafecu Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front Bjdpfx Aaji Riy Eofscu 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: ee3256d63dd23b3ad1bdf9ab0, empty load weight: 10,280 kg, maximum load weight: 13,720 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box on offset recessed in the floor with cover, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the low bed in the tramline area after the offset, sloping towards the entrance, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area 400 mm higher than wheel recess.2nd pair of wheel recesses between the axles in the drop center in the tramline area, slanted towards the entrance, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Wheel well cover can be pulled out from the main frame, with wooden inserts. Distance from main frame beam to beam outside approx. 1280 mm (wheel well area) Widenings extendable to 3,000 mm, foldable on the wheel recess extensions (widening not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed or under the cargo bed if technically possible Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 8 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 2 x at the front on the offset 6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension with lift & lower valve can be operated separately at the front and rear Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Bcsdpfxei Ri I Ne Aafsu Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Trailer Infocenter, for displaying vehicle data such as axle load (no calibrated scales) and odometer Axle load detection via EBS-Canbus signal, for display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Vehicle - driving stability system Duomatic connection at the front, with connecting cable to the truck, EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnoses may occur even though the function is given) 2 white front position lights in LED 2 white/red rear lane departure ligh

Condition: new, machine/vehicle number: 408ba9a39bbb8087056d6e563, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Bcodpfji Ri Dajx Aafsu 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° / D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of approval / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized

Condition: new, machine/vehicle number: ede0610378cbe39cc4883251d, empty load weight: 24,000 kg, maximum load weight: 7,550 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction 1st pair of wheel recesses after steel platform recessed in the tramline area, inclined towards the entrance, length at the bottom approx. 1400 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. If machines are to be driven where the overall height is to be checked, we request a technical data sheet for the machine types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer). Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 110 3 pairs of lashing points, 10 tons each, integrated in the floor at the front Incl. 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x to neck area remaining distributed in between Distance not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, Bcedei Ri Ryjpfx Aafeu ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles which guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Twin steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, incl. Afterwards with 70 mm softwood floor, steel/checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. cannot be achieved. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Incl. with

Condition: new, machine/vehicle number: 15431365fe5515297a6a9fb05, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Bedpfei Ri A Ssx Aafjcu Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: d461243f559015adca5bb372c, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Bcodpfxji Ri Dls Aafeu Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco, Knorr or Haldex Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Bcjdpfx Aei Ri Ddoafeu Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 55d3c5c03e032385649769b1b, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box recessed in Incl. Turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Bcjdpfsi Ri I Eox Aafsu Low loader lashing eyes 3 pairs of lashing points, 10 tons each, integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm towing eye Please note! With 40 mm drawbar eye, the maximum permissible total weight of the truck is 18000 kg, otherwise 50 mm drawbar eye required. Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring jack support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany 1 with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame Ral 3002 carmine red 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: f8fb99947a1c19bc4d63549ff, empty load weight: 6 kg, maximum load weight: 17 kg, overall weight: 24 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 7 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Bjdpfx Aaei Riwfsfjcu Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion with M&S marking Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Coun

Condition: new, machine/vehicle number: f79a9f15e7131d57a512793ab, empty load weight: 8,900 kg, maximum load weight: 15,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Widenings extendable to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical incl. axle load compensation front and rear Axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front offset with steel/ checker plate covering Then with 70 mm softwood floor, steel/checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany With Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Incl. Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Bsdpfxei Ri Izs Aafjcu Drive-on ramps Hot-dip galvanized

Condition: new, empty load weight: 6,950 kg, maximum load weight: 24,050 kg, overall weight: 31,000 kg, axle configuration: 3 axles, loading space length: 7,500 mm, loading space width: 2,550 mm, suspension: air, tire size: 235 / 75 R 17,5, color: other, gearing type: other, front tire size: 235 / 75 R 17,5, rear tire size: 235 / 75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Chassis: hot-dip galvanized, wooden floor 70 mm thick, 18 lashing rings, 12 stake pockets, 2 ramps each 3,110 mm long x 760 mm wide, hydraulic one-piece ramps, loading height: 880 mm, incl. axle load indicators. Surcharges: last axle as steering axle: €3,500; warning signs + lighting and beacon: €200; widening to 3m with wooden planks: €300; hydraulic ramp shift: €1,000. Also available with K80 towing eye! -- Errors, omissions and changes excepted, sample images -- More data at: !, More Details: ! Bsdpfox S N Dcox Aafocu

Condition: new, empty load weight: 6,950 kg, maximum load weight: 24,050 kg, overall weight: 31,000 kg, axle configuration: 3 axles, loading space length: 7,500 mm, loading space width: 2,550 mm, suspension: air, tire size: 235 / 75 R 17,5, color: other, gearing type: other, front tire size: 235 / 75 R 17,5, rear tire size: 235 / 75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Chassis: hot-dip galvanized, wooden floor 70 mm thick, 18 lashing rings, 12 stake pockets, 2 ramps each 3,110 mm long x 760 mm wide, hydraulic one-piece ramps, loading height: 880 mm, incl. axle load indicators. Surcharges: last axle as steering axle: €3,500; warning signs + lighting and beacon: €200; widening to 3m with wooden planks: €300; hydraulic ramp shift: €1,000. Also available with K80 towing eye! -- Errors, omissions and changes excepted, sample images -- More data at: !, More Details: ! Bcedpfx Aasx Sxqrofou

Condition: used, Condition: NEW with pneumatic clamping device. The universal assembly station for the production of wall, ceiling and roof elements in timber frame construction,ceiling and roof elements in timber frame construction. - Heavy-duty, basic structure of the machine frame for a flat work surface - Clamping of the elements via 9 system clamping beams with pneumatic pressure cylinders. The system clamping beams are extendable for element heights from 100 to 3,800 mm. The cylinder stroke is 320 mm, the clamping force per cylinder is approx. 420 kg/4,200 N. at 10 bar operating pressure It can be clamped in two groups of 5 pieces and 4 pieces, two elements can be clamped/worked on at the same time. - Planking of the work surface as far as technically possible with wooden panels. (A perforated metal panel is available as an option, as shown in the photo)) - Stop system at the bottom with 9 pins and at the side with 7 pins for dimensionally accurate elements. - Swivelling device of the assembly station via 3 hydraulic cylinders for panel weights up to panel weights of up to 4,000 kg to 85° (95°). The hydraulic system is compactly integrated in the frame area of the assembly station. - The electrical control cabinet is also installed underneath the assembly station for protection. - The functions are operated via a control bottle. - A compressed air connection and socket are installed on both ends of the station. and on the long side of the station there are 2 sockets and 2 compressed air connections compressed air connections for connecting hand-held devices. - The stations are modular in design, so that they can be expanded immediately or later with a to form a complete turning station. You can see a turning station in picture 3. Bedpfx Aajwv Tqbsfjcu - Further options: Assembly table without set-up function Perforated metal panels Other working dimensions on request Working area: - Maximum element size (W x H): 12,000 x 3,800 mm - Minimum element size (W x H): 1,000 x 100 mm - Cylinder stroke of the clamping cylinders: 320 mm - Stop/ socket pin height: 120 mm - Working height: approx. 700 mm - Colour RÁL 7035 light grey

Condition: used, maximum load weight: 27,500 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 06/2023, next inspection (TÜV): 06/2025, loading space volume: 100 m³, Year of construction: 2023, Equipment: ABS, bioSTAR approx. 100 cbm, 14.9 m internal length silver grey BIOSTAR - STEERABLE AXLE - V14900 - VERTICAL FRONT WALL - VERTICAL REAR DOOR Internal body length: approx. 14,900 mm Internal body width: 2,475 mm Body volume: approx. 90 cbm Gross vehicle weight (GVW): 36 t Axle spacing: 1,310 mm Unladen weight: 8,500 kg King pin height: 1,150 mm TECHNICAL DESCRIPTION 1. CHASSIS KING PIN HEIGHT: Precise king pin height is 1,150 mm. AXLES Tridem: Manufacturer: SAF - CUSTOM DESIGN (CD) Capacity: 3 x 9 t Suspension: Original SAF air suspension Brakes: Large disc Wheel offset: ET 120 Brake wear indicators (BVA) included The first axle is a self-lifting axle controlled via the EBS-E system. The third axle is a trailing steering axle. CONNECTIONS BRAKE WEAR INDICATOR (BVA): Brake wear indicators are connected. LIFT AXLE FUNCTION: Without lift axle. Including traction aid. Bcedpfx Ajxplxzjafsu TRACTION AID: The traction aid is activated by pressing a button in the truck (button in truck not included). AIR SUSPENSION: Lifting and lowering function. Aluminum air tanks. STEERABLE TRAILING AXLE LOCKING: Locking of the steerable trailing axle is managed as follows: - via reverse lights - by button in truck (button in truck not included) TYRES: 6 x 385/65 R 22.5 tyres for regional haulage (manufacturer's choice) on ALCOA MATT aluminum rims, ET 120. BRAKING SYSTEM - EBS: EBS-E system WABCO 2S/2M - PREMIUM MODULATOR Dual-line compressed air braking system in accordance with CE guidelines. Spring-loaded parking brake operating on 2 axles. With SMARTBOARD. R.S.S. (Roll Stability System) LIGHTING - ASPÖCK: 24 Volt electrical equipment. 2 x 7-pin + 1 x 15-pin ISO sockets. Aspöck kit. Orange LED lighting mounted on the trailer side. Without junction box at rear - NORDIC. REAR LIGHTING IN UNDER-RUN PROTECTION: Lighting is installed in the fixed aluminum underrun protection. With foldable aluminum lighting cover. 2 x 1 five-chamber lamp - EUROPOINT III - LED version. HYDRAULICS POSITION: Connection at the front wall. With additional connection option below the body in front of support legs. ACCESSORIES EXTENDIBLE LADDER AT REAR: Extendible ladder integrated at rear of vehicle, right side. PNEUMATIC CENTRAL LOCKING: With pneumatic central locking. TOOLBOX: PVC toolbox with key (800 x 460 x 430 mm) SPARE WHEEL HOLDER: Single aluminum spare wheel holder. 2. BODY FRONT WALL: The front wall is made of heavy-duty aluminum plank profiles. INTERNAL SEALING BETWEEN FLOOR AND FRONT WALL: Fixed sealing between floor and front wall using aluminum profile and PVC gasket. SIDE WALLS: Inner and outer surfaces smooth. Double-walled side wall profiles, 600 mm wide - 30 mm thick - 3 mm inside - 2 mm outside (grain specification). Side wall profiles are fully welded on the inside. WEAR PLATE: Aluminum wear plate, rectangular, inside rear, 2000 (L) x 1500 (H) x 4 mm. MOVING FLOOR SYSTEM: CARGO FLOOR CF 500 SL-C, electric control. 21-board floor system. Drive unit consists of 3 double-acting hydraulic cylinders with 200 mm stroke. Rear end plate in stainless steel. FLOOR SYSTEM OPERATION: Electric control with radio remote (genuine Cargo Floor). Loading - stop - unloading via switch. Manual emergency operation using unique red Cargo rotary knob. MOVING FLOOR FRAME: Frame for wheelbase 7,850 mm. 21 floor boards. FLOOR BOARDS: 21 aluminum floor boards - 8 mm ribbed, with welded aluminum end caps. REAR DOOR: 2 portal h

Condition: good (used), Clamping plate, marking plate, measuring plate, measuring table, welding table, welding table, straightening plate, marking plate, straightening table -Clamping plate: on a solid base frame -Clamping surface: 3990 x 1990 mm -Table height: 830 mm -Plate thickness: 15 mm steel plate on wooden planks -Flatness: see photos (straightening sheath not included) -Transport dimensions: 3990/1990/H830 mm Bedpfx Aaewayg Dofocu -Weight: 1500 kg

Condition: new, Including parabolic suspension / livestock gates / spare wheel / upper ventilation / lower ventilation Technical Specifications: • Brand: Ifor Williams • Model: TA510 • Vehicle type: Livestock trailer • Vehicle condition: New vehicle • First registration: Without first registration • TÜV (Roadworthiness) / HU: 2 years from first registration • Internal dimensions (LxWxH): 434 x 178 x 183 cm • External dimensions (LxWxH): 582 x 228 x 234 cm • Load height (floor): 42 cm • Permissible total weight: 3,500 kg • Unladen weight: 1,265 kg • Payload: 2,235 kg • Chassis: Low-loader (wheels beside the body) • Tyres: 175/75R16C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, bolted V-drawbar • Very robust welded steel frame • Frame fully hot-dip galvanized by immersion • Multiple cross members for high point loads • Floor made of pressure-treated timber planks and covered with 2 mm aluminum checker plate • Aluminum side walls • Split access door on the left in direction of travel • Interior lighting • Solid hot-dip galvanized frame assembly • Heat-reflective roof • Lateral upper roof ventilation apertures • Additional lateral lower ventilation openings • 2 side struts for extra rear stability • Aluminum tailgate with integrated anti-slip steps • Swiveling aluminum livestock gate at rear ramp • KNOTT parabolic axles for maximum ride comfort • Large 16-inch tires for optimal road holding • Spare wheel with mount • Automatic reversing system • KNOTT overrun hitch and parking brake • Lockable coupling head • 13-pin plug with coiled cable • Reversing lights • Large-format safety lighting • Integrated rear fog light • Spare wheel with holder • Centrally positioned jockey wheel Accessories available upon request: • Internal cross partition • Reversing lights • 100 km/h approval with shock absorbers • And much more New vehicle with warranty and TÜV. - Financing and leasing options available - Nationwide delivery possible - All prices include VAT - Vehicle registration documents can be sent in advance or temporary license plates (Germany) can be provided - Export plates with customs clearance available Bedpfx Aaox Sxiusfocu Descriptions and images are protected by copyright!! Trailer Center BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers available from stock! We have been specialized dealers and repair workshop for over 30 years for brands including Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many other brands - Errors, omissions, and prior sale excepted -

Condition: new, Incl. ramp & door combination / waste water tank / parabolic suspension / cattle divider / spare wheel / top ventilation / bottom ventilation Technical Data: • Brand: Ifor Williams • Model: TA510 • Vehicle type: Livestock trailer • Vehicle condition: New vehicle • First registration: none • Technical inspection (TÜV / HU): 2 years from first registration • Internal dimensions (LxWxH): 497 x 178 x 214 cm • External dimensions (LxWxH): 647 x 232 x 265 cm • Loading height from ground: 42 cm • Perm. total weight: 3,500 kg • Unladen weight: 1,460 kg • Payload: 2,040 kg • Chassis: Low-loader (wheels beside body) • Tyres: 175/75R16C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, robust bolted V-drawbar • Very stable welded steel frame • Frame fully hot-dip galvanized by immersion • Numerous cross-members for high point load capacity • Floor made of pressure-treated wooden planks with 2 mm thick aluminium tread plate • Aluminium side panels • Split access door on the left in direction of travel • Interior light • Heavy-duty, hot-dip galvanized frame design • Heat-reflective roof • Ventilation openings at upper sides of roof • Additional lower side ventilation openings • 2 side supports for extra rear stability • Rear tailgate made of aluminium with integrated step strips • Tailgate with flap & door combination (switchable between full ramp and individual barn doors) • Rear swing cattle divider gate on ramp made of aluminium • Waste water tank under cargo area • Waste water collection tray in rear interior area • KNOTT parabolic suspension axles for maximum ride comfort • Large 16" tyres for optimal road holding • Spare wheel with mounting bracket • Automatic reversing system • KNOTT overrun device and parking brake • Lockable coupling head • 13-pin plug with spiral cable • Reversing light • Large, high-visibility safety lighting • Integrated rear fog light • Spare wheel with mounting bracket • Centrally mounted jockey wheel Optional accessories available - please enquire: • Interior cross partition (visible in photos!) - at extra cost • Reversing light • 100 km/h approval with shock absorber • And much more New vehicle with warranty and TÜV. - Financing or leasing possible - Nationwide delivery possible - All prices incl. VAT - Vehicle documents can be sent in advance or transit plates (Germany) can be provided Bjdpfx Aasx Sxi Uefjcu - Export plates including customs clearance possible Descriptions and images are copyright protected!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available from stock! We have been a specialist dealer & workshop for over 30 years for Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many more brands - Subject to error, change and prior sale -

Condition: new, Incl. parabolic suspension / livestock gate / spare wheel / roof ventilation / floor ventilation Technical Data: • Brand: Ifor Williams • Model: TA5 • Vehicle type: Livestock trailer Bodpfx Aox Sxh Doafocu • Vehicle condition: New vehicle • First registration: None • Inspection (TÜV/MOT): 2 years from first registration • Internal dimensions (LxWxH): 372 x 156 x 120 cm • External dimensions (LxWxH): 519 x 207 x 165 cm • Loading floor height: 42 cm • Permissible total weight: 2,700 kg • Unladen weight: 780 kg • Payload: 1,920 kg • Chassis: Low-loader (wheels beside the body) • Tyres: 165R13C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, bolted V-drawbar • Very robust welded steel frame • Frame fully hot-dip galvanised by immersion • Numerous cross members for high point load capacity • Floor made of pressure-treated wooden planks with 2 mm thick aluminium chequer plate overlay • Aluminium side panels • Split entry door on the left (in the direction of travel) • Interior light • Heavy-duty, hot-dip galvanised frame • Heat-reflective roof • Roof-mounted side ventilation openings • 2 side reinforcements at the rear for additional stability • Aluminium tailgate with integrated step strips • Swinging livestock gate on aluminium ramp • Parabolic suspension axles by KNOTT for maximum driving comfort • Tyres provide optimum road holding • Spare wheel with mount • Automatic reverse system • KNOTT overrun hitch and parking brake • Lockable hitch head • 13-pin plug with spiral cable • Reversing light • High-visibility safety lighting • Integrated rear fog lamp • Spare wheel with holder • Centrally mounted jockey wheel Optional accessories available on request: • Internal cross partition • Additional reversing light • 100 km/h approval with shock absorbers • and more New vehicle with warranty and TÜV. - Financing or leasing available - Nationwide delivery possible - All prices include VAT - Vehicle registration documents can be sent in advance or export plates (Germany) can be provided - Export plates incl. customs clearance available Descriptions and images are copyrighted!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available for you! We have been specialist dealers and service workshops for Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many more brands for over 30 years. - Subject to errors, omissions, and prior sale -

Condition: new, Incl. parabolic suspension / driving gate / spare wheel / ventilation flaps Technical Data: • Brand: Ifor Williams • Model: TA5 • Vehicle type: Livestock trailer • Vehicle condition: New vehicle • First registration: Without first registration • MOT/General inspection: 2 years from first registration • Internal dimensions (LxWxH): 241 x 156 x 120 cm • External dimensions (LxWxH): 394 x 207 x 165 cm • Loading height (floor): 42 cm • Permissible total weight: 2,700 kg • Unladen weight: 614 kg Bjdox Sxhwjpfx Aafocu • Payload: 2,086 kg • Chassis: Low loader (wheels beside the body) • Tyres: 165R13C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, bolted V-drawbar • Highly stable welded steel frame • Frame fully hot-dip galvanized by immersion • Numerous cross-members for high point load-bearing capacity • Floor made of pressure-treated wooden planks with 2 mm thick aluminium tread plate • Aluminium side panels • Split entry door on left side (in direction of travel) • Interior lighting • Solid, hot-dip galvanized chassis frame • Heat-reflecting roof • Roof ventilation openings on both sides at the top • 2 side struts for enhanced rear stability • Rear tailgate made of aluminium with integrated step strips • Hinged rear livestock gate on ramp, aluminium • Parabolic axles by KNOTT for maximum ride comfort • Large 13-inch tyres for optimal road holding • Spare wheel with bracket • Reverse automatic system • KNOTT overrun device and parking brake • Lockable coupling head • 13-pin plug with spiral cable • Reversing light • Large-sized safety lighting • Integrated rear fog lamp • Spare wheel with holder • Centrally positioned jockey wheel Optional accessories available upon request: • Internal cross partition • Reversing light • 100 km/h approval with shock absorbers • And much more New vehicle with warranty and MOT. - Financing or leasing available - Nationwide delivery possible - All prices incl. VAT - Vehicle registration document can be sent in advance or temporary number plates (Germany) can be provided - Export registration incl. customs clearance available Descriptions and images are protected by copyright!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers available from stock for immediate delivery! We have been a specialist dealer and service workshop for more than 30 years for Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many other brands. - Subject to errors, changes, and prior sale -

Condition: new, Incl. parabolic suspension / partition gate / spare wheel / upper ventilation / lower ventilation Technical Data: • Brand: Ifor Williams • Model: TA5 • Vehicle type: Livestock trailer Bodjx Sxh Rspfx Aafjcu • Vehicle condition: New vehicle • First registration: without initial registration • TÜV/MOT: 2 years from first registration • Internal dimensions (LxWxH): 311 x 156 x 183 cm • External dimensions (LxWxH): 465 x 207 x 235 cm • Loading height (floor): 42 cm • Permissible total weight: 2,700 kg • Unladen weight: 875 kg • Payload: 1,825 kg • Chassis: low loader (wheels positioned beside the body) • Tyres: 165R13C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, securely bolted V-drawbar • Highly robust welded steel frame • Frame complete hot-dip galvanized by immersion • Multiple cross members for high point load capacity • Floor made from pressure-treated wooden planks with 2 mm thick aluminium chequer plate • Aluminium sides • Divided entry door on the left in direction of travel • Interior light • Heavy-duty, hot-dip galvanized frame construction • Heat-reflecting roof • Ventilation openings at the top sides of the roof • Additional ventilation openings at the lower sides • 2 side struts for extra stability at the rear • Rear aluminium tailgate with integrated step strips • Swivelling aluminium partition gate at the ramp • Parabolic suspension axles from KNOTT for maximum ride comfort • Tyres for optimal road holding • Spare wheel with bracket • Automatic reverse function • KNOTT overrun device and parking brake • Lockable coupling head • 13-pin plug with spiral cable • Reversing light • Large, high-visibility safety lighting • Integrated rear fog lamp • Spare wheel with bracket • Centrally mounted jockey wheel Optional accessories - contact us for enquiries: • Interior cross partition • Reversing light • 100 km/h approval with shock absorbers • and much more New vehicle with warranty and TÜV. - Financing or leasing available - Nationwide delivery available - All prices include VAT - Vehicle registration documents can be sent in advance or temporary registration plates (Germany) can be provided - Export plates including customs clearance available Descriptions and images are copyright protected!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers available from stock! We have been a specialist dealer and repair workshop for over 30 years for brands including Brian James, Blyss, Debon, Humbaur, Hapert, Unsinn, Cheval Liberte, Ifor Williams, Koch, Lorries, Martz, Stedele, TPV, Tohaco, Vezeko, Variant, Vlemmix, and many more. - Subject to errors, omissions, and prior sale -

Condition: new, Incl. Ramp & Door Combination / Parabolic Suspension / Swing Partition / Spare Wheel / Roof Ventilation / Floor-level Ventilation Technical Specifications: • Brand: Ifor Williams • Model: TA510 • Vehicle type: Livestock trailer • Vehicle condition: New vehicle • First registration: No prior registration • Main inspection: 2 years from first registration • Internal dimensions (LxWxH): 311 x 178 x 183 cm • External dimensions (LxWxH): 462 x 230 x 234 cm • Floor loading height: 42 cm • Perm. gross weight: 3,500 kg • Unladen weight: 962 kg • Payload: 2,532 kg • Chassis: Low loader (wheels beside body) • Tyres: 175/75R16C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, retrofittable DESCRIPTION • Reinforced, securely bolted V-drawbar • Very robust welded steel frame • Frame fully hot-dip galvanized by immersion • Numerous cross members for high point load capacity • Floor made from pressure-treated wooden planks with 2 mm thick aluminium chequer plate • Aluminium side panels • Divided access door on left side (in direction of travel) • Interior light • Heavy-duty, hot-dip galvanized frame structure • Heat-reflective roof • Roof-level side ventilation openings • Additional lower side ventilation openings • 2 rear side struts for added stability at the rear • Aluminium tailgate with integrated tread strips • Tailgate/door combination (can be switched between full-width ramp and individual swing doors) • Rear livestock swing partition on ramp, made of aluminium, swivelling • KNOTT parabolic axle suspension for maximum ride comfort • Large 16-inch tyres for optimal road holding • Spare wheel with bracket • Automatic reversing mechanism • KNOTT overrun braked coupling and parking brake • Lockable coupling head • 13-pin plug with coiled cable • Reversing light • Large-size safety lighting • Integrated rear fog lamp • Spare wheel with holder • Central jockey wheel Optional retrofittable accessories—please enquire: • Interior transverse partition • Reversing light • 100 km/h approval with shock absorbers • And much more New vehicle with warranty and TÜV certificate. - Financing or leasing possible - Nationwide delivery available - All prices incl. VAT - Vehicle registration documents can be sent in advance, or transfer number plates (Germany) can be provided - Export number plates incl. customs clearance available Descriptions and images are copyright protected! Trailer Center BAUMANN GmbH Dekkers Waide 17 46419 Isselburg, Germany Over 1,200 trailers available immediately from stock! We have been your specialist dealership and service workshop for Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many other brands for over 30 years. - Errors, omissions, and prior sale excepted - Bsdpfxjx Sxinj Aafocu

Condition: new, Incl. ramp and barn door combination / parabolic suspension / cattle grid / spare wheel / upper ventilation / lower ventilation Technical Data: • Brand: Ifor Williams • Model: TA510 • Vehicle type: Livestock trailer • Vehicle condition: New vehicle • First registration: Not yet registered • TÜV/HU: 2 years from first registration • Internal dimensions (LxWxH): 434 x 178 x 183 cm • External dimensions (LxWxH): 582 x 228 x 234 cm • Load bed height: 42 cm • Perm. total weight: 3,500 kg • Unladen weight: 1,265 kg • Payload: 2,235 kg • Chassis: Low-loader (wheels beside the body) • Tyres: 175/75R16C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h road approval: Optional, retrofittable DESCRIPTION • Reinforced, heavy-duty bolted V-drawbar • Very robust welded steel frame Bodjx Sxizjpfx Aafscu • Complete frame hot-dip galvanized by immersion • Multiple cross members for high point load capacity • Floor made from pressure-treated timber planks and 2 mm thick checker plate aluminium • Aluminium side panels • Split access door left-hand side in direction of travel • Interior lighting • Heavy-duty hot-dip galvanized frame structure • Heat-reflective roof • Side roof ventilation openings • Additional lower side ventilation openings • 2 rear side struts for extra stability • Aluminium rear ramp with integrated non-slip strips • Rear ramp with barn door combination (convertible between full-width ramp and individual barn doors) • Swinging aluminium livestock gate at rear ramp • Parabolic axle suspension by KNOTT for maximum driving comfort • Large 16-inch tyres for optimum road holding • Spare wheel with bracket • Automatic reverse system • KNOTT overrun brake and handbrake • Lockable coupling head • 13-pin plug with spiral cable • Reversing lights • Large safety lighting • Integrated rear fog light • Spare wheel with mount • Centrally mounted jockey wheel Optional retrofittable accessories – please enquire: • Internal cross divider • Reversing light • 100 km/h road approval incl. shock absorbers • and much more. New vehicle with warranty and TÜV. - Financing or leasing available - Nationwide delivery available - All prices incl. VAT - Vehicle registration document can be sent in advance or export/temporary plates (Germany) can be provided - Export plates incl. customs clearance available Descriptions and pictures are copyright protected!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available from stock! We are an official dealer and repair workshop for over 30 years, representing Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many other brands. - Subject to errors, changes, and prior sale -

Condition: new, Incl. ramp & door combination / parabolic suspension / dividing gates / spare wheel / top ventilation / bottom ventilation Technical Specifications: • Brand: Ifor Williams • Model: TA5 HD • Vehicle type: Livestock trailer • Vehicle condition: New vehicle • First registration: None • TÜV/Inspection: 2 years from first registration • Internal dimensions (LxWxH): 372 x 156 x 183 cm • External dimensions (LxWxH): 525 x 207 x 234 cm • Loading height (floor): 42 cm • Perm. gross weight: 3,500 kg • Unladen weight: 1,057 kg • Payload: 2,443 kg • Chassis: Low loader (wheels beside the body) • Tyres: 175/75R16C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, retrofittable DESCRIPTION Bcsdpfxjx Sxihe Aafju • Reinforced, bolted V-drawbar • Very robust welded steel frame • Frame hot-dip galvanized by total immersion • Multiple crossmembers for high point load capacity • Floor made of pressure-treated wooden planks with 2 mm thick aluminium tread plate • Aluminium side panels • Split access door, left in direction of travel • Interior light • Heavy-duty, hot-dip galvanized frame assembly • Heat-reflective roof • Lateral ventilation openings at roof level • Additional lateral ventilation at the bottom • 2 rear side struts for extra stability • Rear tailgate made of aluminium with integrated step strips • Tailgate with ramp-door combination (switchable between full ramp and individual wing doors) • Rear dividing gate on the ramp made of swivelling aluminium • Parabolic axle suspension by KNOTT for maximum driving comfort • Large 16-inch wheels for optimal road holding • Spare wheel with carrier • Automatic reverse function • KNOTT overrun braking system and parking brake • Lockable coupling head • 13-pin plug with spiral cable • Reversing lights • Oversized safety lighting • Integrated rear fog lamp • Spare wheel with bracket • Centrally mounted jockey wheel Optional accessories on request: • Internal cross partition (as seen in images, at extra cost) • Reversing lights • 100 km/h approval with shock absorbers • and more. New vehicle with warranty and TÜV. - Financing or leasing available - Nationwide delivery available - All prices incl. VAT - Vehicle registration documents can be sent in advance, or temporary plates (within Germany) can be supplied - Export plates incl. customs clearance available Descriptions and images are protected by copyright!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available from stock! We have been authorized dealers and workshop for over 30 years for Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many more brands - Errors, omissions and prior sale excepted -

Condition: used, maximum load weight: 42,400 kg, overall weight: 64,000 kg, axle configuration: > 3 axles, first registration: 01/2011, Equipment: ABS, Goldhofer STZ-VLS4-37/80 and Goldhofer Dolly SX 1-25/80 - Height-adjustable low bed with removable gooseneck ----* Manufacturer: Goldhofer * Type: STZ-VLS4-37/80 * First registered: 01/2011 * Color: yellow * Total weight: 64,000 kg * Empty weight according to vehicle registration document: 21,600 kg * Axles: 4x BPW axles, of which 1st axle is steered via turntable steering, the remaining 3x axles are hydromechanical forced steering * Steering knuckle axles up to max. 45 degrees * Tires: 235/75 R17.5 approx. 70% * Suspension: Air suspension with lifting and lowering * EBS Wabco * Removable gooseneck with aluminum side walls * Hydraulic cylinders for support on the tractor unit * Toolbox with flap at the front of the gooseneck * Controls and pressure gauge on the left of the gooseneck * Gooseneck designed for freely rotating 1-axle dollies * Low bed for the chassis can be raised and lowered hydraulically * Chassis with excavator trough (starts from the 2nd axle) * Extendable widening of the loading area 440mm (2x 220mm) and 700mm (2x 350mm) * Wooden planks to bridge the gap between the widenings * Air suspension with raising and lowering to min. 825mm to 1,025mm (no driving position) * 2x fixed driving heights: * 1st driving height 925mm +100mm/-100mm * 2nd driving height 885mm +100mm/-100mm * 2 pairs of retractable lashing eyes in the gooseneck floor * 5 pairs of retractable lashing eyes in the low bed floor * 5 pairs of side lashing eyes on the low bed chassis * 4 pairs of stake holes in the low bed floor * 3 pairs of retractable lashing eyes in the chassis floor * 2 pairs of side lashing eyes on the chassis chassis * 2 pairs of stake holes in the chassis floor * 2x lashing eyes in the excavator trough * Rear of the vehicle sloped 10 degrees * 1-part hydraulic ramps (2,850mm x 720mm) and hydraulic supports at the rear * Operation of hydraulic ramps + supports at the rear left * Smartboard at the rear right * Additional LED reversing lights on the gooseneck and at the rear of the low loader * 1st hand German vehicle!! German papers!! 1st hand!! Goldhofer SX 1-25/80 Dolly ----* Manufacturer: Goldhofer * Type: SX 1-25/80 * First registered: 03/2011 * Color: Yellow * Total weight: 28,000 kg * Empty weight according to vehicle registration document: 2,750 kg * Axles: 1x BPW axle * Tires: 235/75 R17.5 approx. 70% / twin tires Bodpsx Suzajfx Aafocu * 3" fifth wheel plate * Single fender * Supports * Loading manometer * 1st hand German vehicle!! German papers!!