Used Marcelo Plank for sale (190)

Condition: used, mileage: 6,200 km, power: 115 kW (156.36 HP), first registration: 11/2025, fuel type: diesel, overall weight: 3,500 kg, next inspection (TÜV): 11/2027, color: white, gearing type: automatic, number of seats: 3, loading space length: 2,900 mm, loading space width: 2,100 mm, loading space height: 1,900 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), Subframe: Stable, lightweight aluminum construction. Longitudinal and transverse beams made of aluminum. Subframe connected to the chassis according to the truck manufacturer's guidelines. External frame with lashing points. Floor: Consisting of 18 mm thick vehicle construction panels, with a film coating on the underside to prevent moisture penetration, and a non-slip screen-printed texture on the top. The panels are laid flat and sealed around the perimeter. Front wall: Closed with corner posts extending to under the roof, filled with aluminum hollow profiles. Side walls: Equipped with a PentaWave sliding tarp system, which is supported both at the top and bottom in specially shaped profiles. The sliding rollers inside allow the side walls to be moved effortlessly. These can be easily and quickly closed using the integrated tensioning system. Rear wall: Open, prepared for the installation of rear doors (see special versions!). Roof: Fixed roof, consisting of clamped crossbars in a 400 mm grid, with a tarp above. Impact protection: Aluminum strip attached to both sides to guide the Penta-Wave system. Accessories: 1 set of mudguards including mud flaps Holder for wheel chocks Red position lights above the rear portal on the left and right, as LEDs 3rd brake light in the center above the rear portal doors, as an LED Contour marking according to ECR R48, white on the sides and red at the rear, strip width 55 mm Load securing with KIM system 3 rows of Ancra Jungfalk with TRS locking bars KIM 5 x 7 cm (ceiling-guided) with horizontal spring telescopic rods 3 additional locking bars KIM 5 x 7 cm (without ceiling guidance). Mounting of barrier bars to the additional locking bars on the right and left made of aluminum square tube for load securing in the longitudinal direction. Interior lighting 1 LED light strip, centered in the body, including connection to the driver's cab switch. Two-wing rear door Made of aluminum sandwich panels with internal rotary latch closures. The doors have a smooth surface (optimal for lettering). Drop-down brackets for hole rows in the outer frame 4 pieces per side, mounted with a flap and stop nut (more can be installed upon customer request). Side impact protection Side flank protection, brackets galvanized and foldable, planks anodized. Rear view camera Rear view camera including connection to the monitor or navigation system installed by the truck manufacturer. Tsdozhdldepfx Acneb If you have any questions about this vehicle, please contact Mr. Markus Müller:

Condition: used, maximum load weight: 31,335 kg, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 10/2022, next inspection (TÜV): 01/2026, loading space volume: 92 m³, Equipment: ABS, Sliding floor trailer with conical trough design, 92 m³ volume, 385/65 tires, ABS, ESP, 3x9 t SAF B9-22S Intradisc CD IO37 axles with 22.5 inch (430 x 45) disc brakes, ET 120 2040/1200; 9 t BPW SRBF Eco Air axle with 22.5 inch Eco Disc TS2 disc brakes ET 120; Wabco braking system with control box; lift axle on the first axle; automatic raising and lowering / starting aid controlled via EBS; Rectus 26KA air connection; 6x steel rims 22.5x11.75 inch ET120; Europoint 3 Hybrid lighting; 2x LED work lights mounted inside, in the upper corner of the front wall; floor: aluminum, 21-plank, 8 mm, smooth surface; hydraulic connection at front wall; radio remote control; ladder on the right of the front wall or on the front wall door; 12 pairs of lashing rings embedded in the side floor profiles in pairs; 2x round 80 mm bows (not swiveling) + 1x round 50 mm front + 1x round 50 mm rear; wear plates left/right at the rear section inside, aluminum 1250x2500x3mm; 2 rail cleaners made of plastic, attached to the carriage with a chain; plastic toolbox; roll tarp with tension belt; foldable A-board (rear side in body color white); side underrun protection with plastic plate; Rollfix. Tsdpfxezp Tgto Acneb

Condition: used, empty load weight: 6,623 kg, maximum load weight: 32,377 kg, overall weight: 39,000 kg, axle configuration: > 3 axles, first registration: 08/2018, loading space length: 13,620 mm, loading space width: 2,480 mm, loading space height: 3,000 mm, loading space volume: 101 m³, total length: 13,620 mm, suspension: air, tire size: 445/45 19,5, color: yellow, Year of construction: 2018, front tire size: 445/45 19,5, rear tire size: 445/45 19,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, Reference no. for inquiries: 41585 Schmitz, SCB S3T * Year of manufacture: 2018 * ABS, Anti-lock Braking System * EBS, Electronic Braking System Todjzurwhspfx Acnob * Air suspension * Plain tarpaulin * Used tarpaulin * Edscha / Sliding roof cover * Load securing certificate DIN EN 12642 Code XL * VDI 2700 EN 12195 * Lashing point perforation in the outer frame (Multilock outer frame) * Retractable lashing eyes * Pallet stop rail * Mechanically operated lift roof * DCE 9.5 Daimler Chrysler Certificate * Portal door * Aluminum side rails * Air connection, coupling head (red + yellow) * Connector plug, 2x7-pin * Connector plug, 15-pin * Lifting and lowering device * Ferry lashing system * Storage box / Tool box * Galvanized * Suspension: Air * Gross vehicle weight: 39,000 kg * Tare weight: 6,623 kg * Payload: 32,377 kg * Permissible gross vehicle weight: 39,000 kg * Axle manufacturer: Schmitz Rotos * Tire condition 1st axle: -- - Tire size: 445/45 R19.5 * Tire condition 2nd axle: -- - Tire size: 445/45 R19.5 * Tire condition 3rd axle: -- - Tire size: 445/45 R19.5 * Tire size: 445/45 R19.5 * Internal dimensions: L = 13,620 mm, W = 2,480 mm, H = 3,000 mm * Internal volume: 101 m³ * Pallet spaces: 34 * Aluminum plank tarpaulin * Second ride height Varios * 28 mm floor, 7,100 kg forklift axle load * On request, we will send you a video * Construction details and further images Disclaimer: Subject to changes, prior sale and errors. You can find more pictures and videos on our website. Our comprehensive service includes, for example: * Purchase / Sale / Rental of commercial vehicles * Fast and straightforward financing * Application for all (export) documents * Ordering of export license plates / customs license plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading / cargo securing * TÜV inspections, registration service * Transport of commercial vehicles Please contact our trained specialists, who will be happy to advise you.

Condition: used, Year of construction: 2008, color: blue, overall weight: 16,000 kg, maximum load weight: 15,999 kg, empty load weight: 1 kg, loading space volume: 57 m³, loading space width: 2,480 mm, loading space length: 7,700 mm, loading space height: 3,000 mm, first registration: 06/2008, axle configuration: 2 axles, total length: 7,700 mm, driver cabin: day cab, emission class: none, Equipment: truck registration, Vehicle number for inquiries: 41441 Krone, WP 7.7 N3S-CS * Year of manufacture: 2008 * 7.82 (presumably meters) * Used tarpaulin * Fixed roof * Lashing eyelets in the outer frame (Multilock outer frame) * Pallet stop bar * Portal door * Profiled wooden planks * Suitable for rail transport – can be lifted with a crane * Other * Total weight: 16,000 kg * Tare weight: 1 kg * Payload: 15,999 kg * Permissible total weight: 16,000 kg * Internal dimensions: L=7700 mm, W=2480 mm, H=3000 mm * Internal volume: 57 m³ * Dimensions of corner brackets: E=5853 mm * Overhang dimensions: 983 mm * Pallet spaces: 19 * Krone WP 77 BDF Jumbo volume interchangeable box * Liftable roof Disclaimer: Subject to changes, prior sale, and errors. More images and videos can be found on our website. Our comprehensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Quick and straightforward financing * Application for all (export) documents * Ordering export license plates / customs license plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. Tjdezkrfkopfx Acnjb * Professional loading / load securing * TÜV inspections, registration service * Transfer of commercial vehicles Please ask our trained specialists; we will be happy to advise you.

Condition: used, Year of construction: 2008, color: blue, overall weight: 16,000 kg, maximum load weight: 15,999 kg, empty load weight: 1 kg, loading space volume: 57 m³, loading space width: 2,480 mm, loading space length: 7,700 mm, loading space height: 3,000 mm, first registration: 06/2008, axle configuration: 2 axles, total length: 7,700 mm, driver cabin: day cab, emission class: none, Equipment: truck registration, Vehicle number for inquiries: 41436 Krone, WP 7.7 N3S-CS * Year of manufacture: 2008 * 7.82 [presumably meters] * Used tarpaulin * Fixed roof * Lashing eyelets in the outer frame (Multilock outer frame) * Pallet stop bar * Portal door * Profiled wood planks * Suitable for rail transport - can be lifted with a crane * Other * Gross vehicle weight: 16,000 kg * Tare weight: 1 kg * Payload: 15,999 kg * Permissible gross vehicle weight: 16,000 kg * Internal dimensions: L=7700 mm, W=2480 mm, H=3000 mm * Internal volume*: 57 m² * Dimensions of corner brackets E=5853 mm * Dimensions of overhang: 983 mm * Pallet spaces: 19 * Krone WP 77 BDF Jumbo volume swap body * Lifting roof Disclaimer: Subject to changes, prior sale, and errors. More photos and videos can be found on our website. Our extensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Fast and straightforward financing * Application for all (export) documents * Ordering of export license plates / customs license plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading / load securing * TÜV inspections, registration service * Transport of commercial vehicles Tsdozlxd Njpfx Acnjb Please ask our trained specialists; we will be happy to advise you.

Condition: used, Year of construction: 2008, color: blue, overall weight: 16,000 kg, maximum load weight: 15,999 kg, empty load weight: 1 kg, loading space volume: 57 m³, loading space width: 2,480 mm, loading space length: 7,700 mm, loading space height: 3,000 mm, first registration: 06/2008, axle configuration: 2 axles, total length: 7,700 mm, driver cabin: day cab, emission class: none, Equipment: truck registration, Vehicle number for inquiries: 41440 Krone, WP 7.7 N3S-CS Tedpfx Aozkrfqjcneb * Year of manufacture: 2008 * 7.82 (presumably meters) * Used tarpaulin * Fixed roof * Lashing eyelets in the outer frame (Multilock outer frame) * Pallet stop bar * Portal door * Profile wood planks * Rail transportable - craneable * Other * Total weight: 16,000 kg * Unladen weight: 1 kg * Payload: 15,999 kg * Permissible total weight: 16,000 kg * Internal dimensions: L=7700 mm, W=2480 mm, H=3000 mm * Internal volume: 57 cubic meters * Dimensions of corner fittings: E=5853mm * Dimensions of overhang: 983mm * Pallet spaces: 19 * Krone WP 77 BDF Jumbo volume interchangeable body * Lifting roof Disclaimer: Subject to changes, prior sale, and errors. More photos and videos can be found on our website. Our comprehensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Quick and uncomplicated financing * Application for all (export) documents * Ordering of export license plates / customs license plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading / cargo securing * TÜV inspections, registration service * Transfer of commercial vehicles Please ask our trained specialists, we will be happy to advise you.

Condition: used, mileage: 150 km, power: 129 kW (175.39 HP), first registration: 09/2026, fuel type: diesel, overall weight: 7,200 kg, color: white, gearing type: mechanical, emission class: euro6, number of seats: 3, loading space length: 4,800 mm, loading space width: 2,200 mm, loading space height: 2,400 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, parking heater, soot filter, tail-lift, Are you looking for a different model, engine variant, size, or other features? Feel free to contact us. We offer financing and leasing at attractive terms – also available for the Netherlands, Austria, and start-ups! ----Vehicle: * Wheelbase: 4,100 mm * 6-speed manual gearbox * Single cab * Twin rear wheels * Gross vehicle weight: 7.2 tonnes * Digital tachograph * Speed limiter: 90 km/h Interior: * Passenger bench seat with multifunction storage * Overhead storage compartment above the windshield * Luxury driver's seat, sprung, heated * Grab handle on A-pillar * Comfort headrests * Leather multifunction steering wheel * Cloth seat covers Safety & Assistance: * Electronic Stability Program (ESP) * AEBS System + City Brake * Driver airbag * Front monitoring system (MOIS) * Oper. & maint. manual electronic * Rear parking sensors * Lane Centering Plus (LC) * Eco-Smart function * Additional speed limiter * Seatbelt warning signal F/B * Driver Drowsiness Alert (DDAW) * Turn assist, passenger side (BSIS) * Rear blind spot radar * Traffic sign recognition incl. (ISA) * Spare wheel with rear frame mounting Wheels & Technology: * Electrically adjustable and heated mirrors * Digital radio DAB 7" touch display * Apple CarPlay/Android Auto * All-weather tires * AIRPRO air suspension on rear axle * Manual central handbrake * Air conditioning with automatic climate control * Heated fuel filter * Auxiliary hot water heater * Light and rain sensor Tedpsv R Rfmjfx Acnsb * Fog lights * Full LED headlights * 4G connectivity box incl. TCO * Adaptive cruise control (ACC) * Pre-wiring for toll system (OBU) * Central locking with remote control * AdBlue tank 20 L and driver heater * Integrated 90 L fuel tank * Battery 12V 110 Ah Sliding Curtain: * Steel frame * Antislip plywood flooring * Side aluminium drop-in planks * Sliding curtains both sides (color: black, other colors on request) * Upper guide rail for sliding curtain * Lower securing straps for sliding curtain * Roof spoiler * Tailgate * Reversing camera * Side underrun protection * Mudguards with splash flaps * Side marker lights Tail Lift: * Dhollandia * Load capacity: 1,500 kg * Platform depth: 1,800 mm * Roll-off protection * LED warning lights * Remote control with spiral cable * Towbar up to 3.5t trailer payload (ball hitch, 13-pin 12V trailer socket) Additional bodywork extras available for a surcharge. ----Notice: Please call before your visit – we want to ensure your required vehicle is available on site. If the vehicle is not in Wachtendonk, we are happy to deliver from our stock. Custom builds available on request. Your vehicle partner since 1996. Call or email now – we look forward to hearing from you! No liability for typographical or printing errors. Subject to prior sale and changes.

Condition: used, Year of construction: 2013, color: blue, overall weight: 16,000 kg, maximum load weight: 15,999 kg, empty load weight: 1 kg, loading space volume: 57 m³, loading space width: 2,480 mm, loading space length: 7,700 mm, loading space height: 3,000 mm, first registration: 06/2013, axle configuration: 2 axles, total length: 7,700 mm, driver cabin: day cab, emission class: none, Equipment: truck registration, Vehicle number for inquiries: 41437 Krone, WP 7.7 N3S-CS * Year of manufacture: 2013 * 7.82 * Used tarpaulin * Fixed roof * Lashing eyelets in the outer frame (Multilock outer frame) * Pallet stop rail * Portal door * Profiled wooden planks * Rail transportable - craneable * Other * Total weight: 16,000 kg * Tare weight: 1 kg * Payload: 15,999 kg * Permissible total weight: 16,000 kg * Internal dimensions: L=7700 mm, W=2480 mm, H=3000 mm * Internal volume*: 57 m³ * Dimensions of corner fittings: E=5853 mm * Dimensions of overhang: 983 mm Tedjzlxd Aepfx Acnob * Pallet spaces: 19 * Krone WP 77 BDF Jumbo volume interchangeable body * Lifting roof Disclaimer: Subject to changes, prior sale, and errors. You can find more photos and videos on our website. Our comprehensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Quick and straightforward financing * Application for all (export) documents * Ordering of export license plates / customs license plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading / load securing * TÜV inspections, registration service * Transport of commercial vehicles Please contact our trained specialists; we will be happy to advise you.

Condition: used, empty load weight: 6,623 kg, maximum load weight: 32,377 kg, overall weight: 39,000 kg, axle configuration: > 3 axles, first registration: 08/2018, loading space length: 13,620 mm, loading space width: 2,480 mm, loading space height: 3,000 mm, loading space volume: 101 m³, total length: 13,620 mm, suspension: air, tire size: 445/45 19,5, tire condition: 40 %, color: yellow, Year of construction: 2018, front tire size: 445/45 19,5, rear tire size: 445/45 19,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, Vehicle number for inquiries: 41583 Schmitz, SCB S3T * Year of manufacture: 2018 * ABS, anti-lock braking system * EBS, electronic braking system * Air suspension * Plain tarpaulin * Used tarpaulin * Edscha / sliding roof tarp * Load securing certificate DIN EN 12642 Code XL Tsdszt Htuopfx Acnjb * VDI 2700 EN 12195 * Lashing eye holes in the outer frame (Multilock outer frame) * Retractable lashing eyes * Pallet stop bar * Mechanical lifting roof * DCE 9.5 Daimler Chrysler certificate * Portal door * Aluminum side walls * Air connection coupling head (red + yellow) * 2x7-pin connecting plug * 15-pin connecting plug * Lifting and lowering device * Ferry lashings * Storage box / tool box * Galvanized * Suspension: Air * Gross vehicle weight: 39,000 kg * Tare weight: 6,623 kg * Payload: 32,377 kg * Permissible gross vehicle weight: 39,000 kg * Axle manufacturer: Schmitz Rotos% * Tire condition 1st axle: 30% -- 30% - Tire size: 445/45 R19.5 * Tire condition 2nd axle: 80% -- 30% - Tire size: 445/45 R19.5 * Tire condition 3rd axle: 30% -- 30% - Tire size: 445/45 R19.5 * Tire sizes: 445/45 R19.5 * Interior dimensions: L=13,620 mm, W=2,480 mm, H=3,000 mm * Interior volume*: 101 m² * Pallet spaces: 34 * Aluminum plank tarpaulin * Second ride height, Varios * 28mm floor, 7,100kg forklift axle load * Upon request, we will send you a video * Construction description and more pictures Disclaimer: Subject to changes, prior sale and errors You can find more pictures and videos on our homepage. Our extensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Quick and easy financing * Application for all (export) documents * Ordering export license plates / customs license plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading / cargo securing * TÜV inspections, registration service * Transportation of commercial vehicles Please ask our trained specialists, we will be happy to advise you.

Condition: used, maximum load weight: 38,230 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 06/2026, loading space length: 8,500 mm, loading space width: 2,520 mm, Müller-Mitteltal Low-loader with Wheel Recesses TS 3 RM ML 30.0, 2 Loading Heights and Ramps * Fifth wheel load increase from 12 t to 18 t incl. Kingpin mounted in: Second kingpin position 2", kingpin up to and incl. 5th wheel height 2,750 mm. Rear turning radius approx. 2,400 mm in clear width (a minimum clearance of 150 mm is recommended). Forward turning radius 1,480 mm or 1,570 mm with spare wheel. Note: Sufficient clearance to the towing vehicle must be ensured by the customer. * Extension parts for the wheel recesses at the front and bottom at the rear (205 mm deep). 6 pieces incl. insertion boards for wheel recesses at the rear. Board holder as receiving shafts according to code 09.112. Aluminum compressed air tank instead of steel. * Smartboard control box mounted on the trailer as an information tool with pressure sensors incl., exclusively for overall axle load display. Display option can be selected via the control box or in the truck via the EBS air suspension system (truck manufacturer-dependent). Tjdpfjy R Ipuox Acneb * ?SP-Combination Package: Tool box with 45° corners made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, on the fifth wheel platform, W=2,480 x H=500 mm with a folding lid on top, side doors and sloping corners. Incl. aluminum side walls that can be folded down to the fifth wheel platform (500 mm high), aluminum rear wall plugged in (150 mm high), aluminum side panels painted inside and out in RAL 9006 white aluminum. Incl. rear uprights, foldable and detachable, galvanized (without topcoat). Incl. bolted front structure. Length of front cross member to 5th wheel height 3,935 mm. Forward turning radius, without spare wheel, at 5th wheel height 2,450 mm or 2,750 mm, approx. 1,750 mm or approx. 1,480 mm. * 2 container locking mechanisms recessed into the front cross member. * 3 receiving shafts under the fifth wheel platform for storing optional aluminum ramps or wooden planks for covering the wheel recesses. * Folding/extendable outrigger (galvanized) and wooden planks for widening incl. (not on the rear slope), plank holder on the fifth wheel platform (the track width of the load may be a maximum of 2,500 mm). * Second LED position light on the warning package at the front and rear (double lighting), only in combination with the warning package. * 2 LED reversing lights on the rear of the trailer, switched with reverse gear (suitable for 12 V and 24 V), max. 2 additional lights in total. * 7-pole socket on the rear, wired for overhang lighting with tail light (58 R) and ground. * Rubber mat on the loading ramp on the left and right (approx. 860 mm long) 190 07644 rubber strip, on the inner plank of the one-piece ramps. * Central lubrication system fully automatic with pump (24 V), grease tank and integrated trailer control, without connection to the ramps (in the case of steering: incl. connection of the distributor of the fifth wheel platform). Note: Only possible with towing vehicles with a 24 V lighting system! Intermediate sale and errors are expressly reserved! Sale exclusively subject to our general terms and conditions (AGB). Important note - Important information: Despite careful checking of all details in our offer, errors may occur. Some of these are caused by transmission errors in the systems of the various platform providers. Therefore, we would like to point out that all information is provided without guarantee and does not c

Condition: excellent (used), 1 roller table 3.0 m long x 0.77 m wide with 7 support rollers, with pneumatic lifting/adjustment chain with worm gear and bellows cylinder, with a timber transfer roller carriage with rubber turntable for 1-man timber feed, with 2 lift-up stop rollers for planks from the band saw that have already been trimmed on one side. Tsdpot E Nw Tjfx Acnob 1 roller table 3.5 m long x 0.77 m wide with 8 support rollers, with or without transfer roller carriage. Original PAUL roller tables in various widths and lengths, available in standard or heavy-duty versions for use in front of cross-cut, trimming and re-cutting circular saws; short work tables allow, for example, the transfer of material from the cross conveyor, passage through the table assembly or the loading of heavy beams by forklift; long work tables are also available in various dimensions

Condition: new, empty load weight: 2,980 kg, maximum load weight: 7,520 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 5,280 mm, loading space width: 2,480 mm, suspension: steel, tire size: 245/70 R 17,5, color: other, gearing type: other, front tire size: 245/70 R 17,5, rear tire size: 245/70 R 17,5, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Ramp approx. 2,700 mm long x 900 mm wide, ramps with grating, loading height: 840 mm, 10 lashing rings of 2.5 t each, 8 lashing rings of 6 t each, steel sidewalls, foldable and removable, wooden planks 50 mm, loading platform rear-side chamfered, internal loading width 2,480 mm, removable rear stanchion, front open for through-loading, also available with 6,300 mm loading platform length!! Rental price from €500, -- Typing errors, mistakes, and technical modifications reserved, sample pictures --, More data at: !, More details: ! Todpszxxbhsfx Acnsb

Condition: used, empty load weight: 6,840 kg, maximum load weight: 32,160 kg, overall weight: 39,000 kg, axle configuration: > 3 axles, first registration: 10/2018, next inspection (TÜV): 07/2027, loading space length: 13,620 mm, loading space width: 2,480 mm, loading space height: 3,000 mm, loading space volume: 101 m³, total length: 13,620 mm, suspension: air, tire size: 435/50 19,5, tire condition: 30 %, color: yellow, Year of construction: 2018, front tire size: 435/50 19,5, rear tire size: 435/50 19,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, rental of commercial vehicles * Fast and straightforward financing * Application for all (export) documents * Ordering of export license plates / customs license plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading / cargo securing Tjdozwt Aqopfx Acnob * TÜV inspections, registration service * Transport of commercial vehicles Ask our trained specialists, we will be happy to advise you.

Year of construction: 2026, condition: new, Ready-to-deliver press feeding line for scaffolding plank production with 4 Ton decoiler, straightener feeder and 200 Ton C-type press. Bosporas Machinery is a manufacturer of coil processing, press feeding and roll forming systems, delivering high-performance and customized industrial solutions worldwide with strong R&D capabilities. This scaffolding plank feeding line is available from stock and ready for fast delivery. The system is designed for perforating, punching and feeding operations in scaffolding plank production and similar metal forming applications. The line combines stable coil feeding, precise straightening and high-capacity press performance in a compact and efficient production solution. Ideal for companies looking for immediate production capacity without long manufacturing lead times. ⚡ FAST DELIVERY ADVANTAGE Stock machine – ready for shipment Fast delivery opportunity Reduced investment waiting time Ready for industrial production setup ⚙️ TECHNICAL CONFIGURATION Coil Width: up to 600 mm Mechanical Decoiler: 4 Ton Capacity Straightening Servo Feeder System C-Type Mechanical Press: 200 Ton Capacity Servo synchronized feeding operation Heavy-duty industrial structure 🔧 LINE COMPONENTS 4 Ton Hydraulic Decoiler Straightening Unit Servo Feeder System 200 Ton C-Type Press Electrical & Automation System Operator Control Panel ⚙️ ENGINEERING FEATURES High precision feeding performance Stable straightening and synchronized press operation Todpfx Ajy Nnftocnsb Heavy-duty press structure for continuous production Servo motor controlled feeding system Compact and operator-friendly design Suitable for integration with roll forming systems ⚡ OPERATIONAL ADVANTAGES Immediate availability from stock Reliable and continuous production Reduced setup and commissioning time Flexible use for punching and perforation applications Short lead time compared to European manufacturers 🏭 APPLICATION AREAS Scaffolding plank production Perforated metal production Sheet metal punching applications Roll forming pre-feeding systems Construction industry components

Condition: like new (used), Year of construction: 2012, Longitudinal profiles for machining on both sides Toothed transport chains for secure wood transport Solid wood planks, castle planks, flooring Wood width currently approx. 260 to 660 mm Wood height currently approx. 15 to 85 mm Chip removal per side up to 50 mm 2 machining motors, each 7.5 kW, on the right 2 machining motors, each 7.5 kW, on the left Feed gearbox motor 3.0 kW Tsdjduw Auepfx Acnob Condition: very good

Condition: used, empty load weight: 7,020 kg, maximum load weight: 35,980 kg, overall weight: 43,000 kg, axle configuration: 3 axles, first registration: 02/2023, loading space length: 13,510 mm, suspension: air, tire size: 445/45 R19,5, color: other, gearing type: other, front tire size: 445/45 R19,5, rear tire size: 445/45 R19,5, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Container closures, extendable, for 2 x 20 ft containers or 1 x 40 ft container, 4 x warning signs with lighting, omega floor with hardwood planks, aluminum rims, Alcoa Dura-Bright finish, front wall approx. 1,800 mm, pallet box for 24 Euro pallets, bracket for securing bars, 16 x bar pockets, 12 x securing bars, approx. 2 m long, new price was €49,000, -- subject to printing errors, mistakes and changes, sample images --, more information available at: !, More Details: ! Tjdpfx Acjzvyhqoneb

Condition: used, Condition: NEW with pneumatic clamping device. The universal assembly station for the production of wall, ceiling and roof elements in timber frame construction,ceiling and roof elements in timber frame construction. - Heavy-duty, basic structure of the machine frame for a flat work surface - Clamping of the elements via 9 system clamping beams with pneumatic pressure cylinders. The system clamping beams are extendable for element heights from 100 to 3,800 mm. The cylinder stroke is 320 mm, the clamping force per cylinder is approx. 420 kg/4,200 N. at 10 bar operating pressure It can be clamped in two groups of 5 pieces and 4 pieces, two elements can be clamped/worked on at the same time. - Planking of the work surface as far as technically possible with wooden panels. (A perforated metal panel is available as an option, as shown in the photo)) Tedpfxezhnafe Acnob - Stop system at the bottom with 9 pins and at the side with 7 pins for dimensionally accurate elements. - Swivelling device of the assembly station via 3 hydraulic cylinders for panel weights up to panel weights of up to 4,000 kg to 85° (95°). The hydraulic system is compactly integrated in the frame area of the assembly station. - The electrical control cabinet is also installed underneath the assembly station for protection. - The functions are operated via a control bottle. - A compressed air connection and socket are installed on both ends of the station. and on the long side of the station there are 2 sockets and 2 compressed air connections compressed air connections for connecting hand-held devices. - The stations are modular in design, so that they can be expanded immediately or later with a to form a complete turning station. You can see a turning station in picture 3. - Further options: Assembly table without set-up function Perforated metal panels Other working dimensions on request Working area: - Maximum element size (W x H): 12,000 x 3,800 mm - Minimum element size (W x H): 1,000 x 100 mm - Cylinder stroke of the clamping cylinders: 320 mm - Stop/ socket pin height: 120 mm - Working height: approx. 700 mm - Colour RÁL 7035 light grey

Condition: used, axle configuration: 3 axles, first registration: 02/2018, loading space length: 6,060 mm, loading space width: 2,200 mm, loading space height: 300 mm, Subject to errors and prior sale! Internal number: 1448. EQUIPMENT * Platform trailer * 3 axles * Support wheel * AL-KO coupling * Planks all around ... and much more ----The vehicle is unprepared! Tjdpfjvwh U Sjx Acneb Nationwide delivery possible for an additional charge. Subject to errors and prior sale. We are happy to accept your vehicle as part payment. Financing/leasing also possible without a down payment! Do you have any questions? We are happy to advise you!

Condition: new, empty load weight: 2,750 kg, maximum load weight: 7,750 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 5,280 mm, loading space width: 2,480 mm, suspension: steel, tire size: 245 / 70 R 17,5, color: other, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, each ramp approx. 2,700 mm long x 560 mm wide, ramps with gratings, loading height: 840 mm, 10 lashing eyes per 2.5 t, 8 x lashing eyes per 6 t, wooden planks 50 mm, loading area slanted at the rear, rear stanchion removable, front for through-loading, , Also available in 6,300 mm loading area length!!!, , Rental price from 500 ¤ , , , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Tjdpfx Ajzxw Iajcnsb

Condition: used, maximum load weight: 27,500 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 06/2023, next inspection (TÜV): 06/2025, loading space volume: 100 m³, Year of construction: 2023, Equipment: ABS, bioSTAR approx. 100 cbm, 14.9 m internal length silver grey BIOSTAR - STEERABLE AXLE - V14900 - VERTICAL FRONT WALL - VERTICAL REAR DOOR Internal body length: approx. 14,900 mm Internal body width: 2,475 mm Body volume: approx. 90 cbm Gross vehicle weight (GVW): 36 t Axle spacing: 1,310 mm Unladen weight: 8,500 kg King pin height: 1,150 mm TECHNICAL DESCRIPTION 1. CHASSIS KING PIN HEIGHT: Precise king pin height is 1,150 mm. AXLES Tridem: Manufacturer: SAF - CUSTOM DESIGN (CD) Capacity: 3 x 9 t Suspension: Original SAF air suspension Brakes: Large disc Wheel offset: ET 120 Brake wear indicators (BVA) included The first axle is a self-lifting axle controlled via the EBS-E system. The third axle is a trailing steering axle. CONNECTIONS Tsdpfxoxplxzj Acnjb BRAKE WEAR INDICATOR (BVA): Brake wear indicators are connected. LIFT AXLE FUNCTION: Without lift axle. Including traction aid. TRACTION AID: The traction aid is activated by pressing a button in the truck (button in truck not included). AIR SUSPENSION: Lifting and lowering function. Aluminum air tanks. STEERABLE TRAILING AXLE LOCKING: Locking of the steerable trailing axle is managed as follows: - via reverse lights - by button in truck (button in truck not included) TYRES: 6 x 385/65 R 22.5 tyres for regional haulage (manufacturer's choice) on ALCOA MATT aluminum rims, ET 120. BRAKING SYSTEM - EBS: EBS-E system WABCO 2S/2M - PREMIUM MODULATOR Dual-line compressed air braking system in accordance with CE guidelines. Spring-loaded parking brake operating on 2 axles. With SMARTBOARD. R.S.S. (Roll Stability System) LIGHTING - ASPÖCK: 24 Volt electrical equipment. 2 x 7-pin + 1 x 15-pin ISO sockets. Aspöck kit. Orange LED lighting mounted on the trailer side. Without junction box at rear - NORDIC. REAR LIGHTING IN UNDER-RUN PROTECTION: Lighting is installed in the fixed aluminum underrun protection. With foldable aluminum lighting cover. 2 x 1 five-chamber lamp - EUROPOINT III - LED version. HYDRAULICS POSITION: Connection at the front wall. With additional connection option below the body in front of support legs. ACCESSORIES EXTENDIBLE LADDER AT REAR: Extendible ladder integrated at rear of vehicle, right side. PNEUMATIC CENTRAL LOCKING: With pneumatic central locking. TOOLBOX: PVC toolbox with key (800 x 460 x 430 mm) SPARE WHEEL HOLDER: Single aluminum spare wheel holder. 2. BODY FRONT WALL: The front wall is made of heavy-duty aluminum plank profiles. INTERNAL SEALING BETWEEN FLOOR AND FRONT WALL: Fixed sealing between floor and front wall using aluminum profile and PVC gasket. SIDE WALLS: Inner and outer surfaces smooth. Double-walled side wall profiles, 600 mm wide - 30 mm thick - 3 mm inside - 2 mm outside (grain specification). Side wall profiles are fully welded on the inside. WEAR PLATE: Aluminum wear plate, rectangular, inside rear, 2000 (L) x 1500 (H) x 4 mm. MOVING FLOOR SYSTEM: CARGO FLOOR CF 500 SL-C, electric control. 21-board floor system. Drive unit consists of 3 double-acting hydraulic cylinders with 200 mm stroke. Rear end plate in stainless steel. FLOOR SYSTEM OPERATION: Electric control with radio remote (genuine Cargo Floor). Loading - stop - unloading via switch. Manual emergency operation using unique red Cargo rotary knob. MOVING FLOOR FRAME: Frame for wheelbase 7,850 mm. 21 floor boards. FLOOR BOARDS: 21 aluminum floor boards - 8 mm ribbed, with welded aluminum end caps. REAR DOOR: 2 portal h

Condition: new, empty load weight: 3,120 kg, maximum load weight: 8,780 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 6,280 mm, loading space width: 2,480 mm, suspension: steel, tire size: 245 / 70 R 17,5, wheelbase: 990 mm, color: other, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Each ramp is approximately 2,700 mm long x 900 mm wide, with grating surfaces. Loading height: 840 mm. 12 lashing points, each rated for 2.5 tons. 8 lashing points, each rated for 6 tons. Steel side rails, foldable and removable. Wooden planks, 50 mm thick. Loading area with a rear incline. Internal loading area width: 2,480 mm. Removable rear ramp. Front design allows for drive-through loading. Vehicle with temporary registration. Also available with a loading area length of 5,300 mm! Rental price starting from 500 EUR. Subject to printing errors, errors and changes. Sample images. More details: ! Tedpfxozxw Igo Acnjb

Year of construction: 2015, operating hours: 2,928 h, condition: used, Dynapac F1700C Model: Year of manufacture: 2015 Operating hours: 2,928 hours Paving capacity: 350 t/h Engine: Deutz TD 2011 L04 52 kW (71 hp) Undercarriage: Hydraulic tracked undercarriage Max. 32 m/min paving speed 3.8 km/h transport speed Material hopper: Mixing material hopper, bunker capacity 4.7 m³ Width (internal): 3,020 mm Feed height (center): 600 mm Push rollers for truck docking Available conveyor unit: Double conveyor belt Slats width: 2 x 350 mm Two-part slatted conveyor with proportional speed control Basic width: 1,700 mm Min. width (with reduction shoe): 700 mm Max. width: 4,400 mm Max. paving thickness: 270 mm Includes widening extensions / plank Weight: 8,800 kg Upon request, we will provide you with a leasing or financing offer. Mr. Mihm (Tel. ) will be happy to assist you. You can find more information on our website. Errors and prior sale excepted! Dynapac F1700 C Tedpfx Aozwlv Nscnjb Model: Year of manufacture: 2015 Operating hours: 2,927 hours Paving capacity: 350 t/h Engine: Deutz, 4-cylinder TD 2.9 L4, [54 kW/72 hp] Fuel tank: 85 l Undercarriage: Hydraulic crawler drive Max. paving speed: 27 m/min Transport speed: 3.3 km/h Material hopper: Material hopper, capacity 2.3 m³ Hopper length: 1,310 mm Width: / Loading height: / Truck push rollers included Conveyor system: Split, reversible scraper conveyor with center cover and automatic control via limit switches Width 650 mm, controlled by an individual drive Screeds: V240TV or V240TVE Basic width: 1,200 mm Max. width: 3,100 mm Dimensions: Length: 4,360 mm Width: 1,200 mm (basic width/transport width) Height: 1,900 mm Weight: 5,800 kg Includes extensions / plank We would be happy to provide a leasing or financing quote upon request. Mr. Mihm (Tel. ) is available to assist you with this. Further information can be found on our website. Subject to errors and prior sale! - = Further information = Please contact Tobias Ebert for more information.

Condition: used, Year of construction: 2009, 2009 | Blomenröhr 674/11900 | Used Low Bed Semi-trailer 📍Location: Germany 🚛 Delivery available to your destination – Use our shipping calculator to estimate transport costs! 💰 Buy Now for EUR 14300 or Make an Offer. Payment at delivery available for an affordable fee (subject to approval)* 👷‍♂️ Inspected by an independent expert 11 inspection points 9 approved ✅ 2 imperfect ℹ️ 0 issues ⚠️ 📌 Inspector's Comment: Technically okay, rust on the axles, planks need to be replaced. 📄 Want to see the full inspection, extra photos, or a video? Tip: The reference "40827 Equippo" is commonly used when looking up more details online. 💡 Why this machine and our service stands out: ✔ Thorough inspection by professionals ✔ Jobsite delivery available ✔ Money-Back Guaranteed ✔ Secure and flexible payment options Tsdpfxsy Ul Upe Acnjb 🔄 Considering other equipment options? We offer helpful tools and resources for all equipment owners and operators – easily accessible on our platform.

Condition: excellent (used), total length: 6,000 mm, total width: 2,400 mm, total height: 670 mm, OPTIONALLY ALSO AVAILABLE WITH ROOF STRUCTURE! Operating Conditions: The trailer is designed for use on flat, paved surfaces in internal company transport. Combined Operation: The trailer components are not (without a trailer coupling) designed for combined operation with multiple trailers. Payload: 16 t at 6 km/h with evenly distributed loading (area load) of the loading platform between the axles. Point or line loads are only permitted upon notification. Loading Platform: Approx. 6000 x 2400 mm, loading height approx. 670 mm, platform covering made of softwood planks, all-round edge protection. Todpsxrtdqsfx Acnob Steering: Four-wheel stub-axle steering, drawbar tiltable, removable, and can be repositioned from front to back, coupling height at the towing vehicle approx. 320 mm (other coupling heights only permitted upon notification), towing eye according to DIN 74054, diameter 40 mm, drawbar drop protection according to UVV. Chassis: Both axles steered, solid rubber elastic tyres approx. 425 x 300 mm, wheel hubs with tapered roller bearings and permanent grease lubrication. Paintwork: Topcoat RAL 5002 Ultramarine Blue. Optional Equipment: - 2 lashing rods made of round steel welded vertically into the outer frame on each long side - Double-acting wheel chock with holder and chain

Condition: good (used), Code: 0389 Brand: ISVE Model: ESC JUNIOR 5 - CE Standard Vacuum dryer for drying timber planks, with top opening particularly suitable for carpenter workshops with problems of space -CE Standard Features: Top opening means that the whole length of the autoclave can be used without having to extract the carriage, thus drastically reducing the overall size The machine, operating at low temperatures, allows the timber to lose its water content without subjecting it to thermal changes which can cause cracking and warping The evaporated water which remains in suspension in the container keeps the drying material surface continuously humidified, avoiding in this way the formation of small cracks where in other drying systems is quite frequent The humidity level which is necessary between environment and material is constantly maintained by a condenser which precipitates the steam in suspension Tjdpfey Ti Ecex Acnob The conditioning of the drying chamber is kept constant and programmed in advance using probes connected to the heating and condensing circuits and to the timber This conditioning of the environment sets the transmigration process of the water through the cellular walls of the timber in motion. Passing from their inside walls towards the surfaces, from which the water is continuously evaporated until the desired drying conditions are reached The condensate which deposits at the bottom of the dry kiln, is periodically expelled in order to maintain the environmental conditions constant. Technical data: Capacity m³ 0,7 Power consumption 0,95 Kw Autoclave: stainless steel for drying wood containing corrosive agents (oak, chestnut, etc.) Insulating covering Shell-opening with pneumatic pistons Electric control panel with microprocessor for automatic running and stopping of drier Humidity control probes of a sample unit Automatic discharge of condensate N° 6 Aluminium electric heating plates Oil lubricated vacuum pump Installed electrical power 3,6 Overall dimensions mm 5900 x 800 x 1200 h Weight kg 500 User and maintenance manual included