Used Letter Press for sale (28,620)

Condition: good (used), Year of construction: 2008, total height: 5,400 mm, installation height: 500 mm, table length: 2,000 mm, table width: 1,100 mm, pressing force: 250 t, overall weight: 57,000 kg, product height (max.): 4 mm, sheet thickness steel (max.): 4 mm, space requirement length: 4,800 mm, space requirement width: 2,750 mm, controller manufacturer: SIEMENS, controller model: S7 300, power: 95 kW (129.16 HP), load capacity: 2,000 kg, coil outer diameter: 2,000 mm, coil weight: 2,000 kg, coil width: 300 mm, number of straightening rollers: 7, product width (max.): 300 mm, sheet thickness (max.): 4 mm, tool height: 500 mm, CONTROLS Hfjdpfxsxnwabj Afien .. electronic controls SIEMENS S7 300 PRESS DESIGN .. drive system: eccentric / crank .. openings in uprights: yes .. number of suspensions: 2 .. table cushion: no .. quick die change system: yes PRESS FORCES .. total force (nominal): 250 to PRESS TABLE .. table surface (left-right): 2000 mm .. table surface (front-back): 1100 mm .. height above floor level: 1105 mm .. opening in bed (left-right): 1700 mm .. opening in bed (front-back): 305 mm SLIDE .. table surface (left-right): 2080 mm .. table surface (front-back): 1000 mm .. stroke rate (max.): 120 /min SLIDE (MECHAN. PRESS) .. slide adjustment: 120 mm .. stroke adjustment: yes .. stroke min.: 20 mm .. stroke max.: 180 mm TOOL ASSEMBLY DIMENSIONS .. shut height (stroke down, adjustment up), BDC: 500 mm .. distance between columns (H-frame): 2055 mm .. passline opening (free passage in side columns): 810 mm DECOILER .. sheet width max.: 300 mm .. coil weight max.: 2 to .. max. diameter of coil: 2000 mm .. mandrel expansion range up to: 550 mm LEVELLER UNIT .. sheet width max.: 310 mm .. number of leveller rolls: 7 .. diameter of leveller rolls: 80 mm STRIP-FEEDER .. feeder type: roll feeder .. sheet width max.: 200 mm .. sheet thickness max.: 4 mm .. speed max.: 120 m/min ELECTRICAL SPECIFICATIONS .. total power consumption: 95 kW .. mains voltage: 400 V .. mains frequency: 50 Hz DIMENSIONS / WEIGHTS .. space requirements -left/right-: 4800 mm .. space requirements -front/back-: 2750 mm .. total height: 5400 mm .. total weight approx.: 57000 kg ATTACHMENTS (PRESSES) .. decoiler: yes .. leveller unit: yes .. European CE standards: yes Machine hours: 20,391 h (operating hours) Adjustment strokes: 20, 39, 69, 99, 125, 148, 165, 175, 180 mm Equipment: - External connecting rods for high tilt stability - Hydraulic overload protection - Press force monitoring - Temperature sensors at the bearing points - ABS AHM 2.0T decoiler (1999) - PBK RSD 8/6/300 straightener (2010) - Loop belt control - LW-060-02 roller feed (2008) - Advanced central lubrication system - Press force monitoring - Temperature sensors at the bearing points - Hydraulic tool clamps - Spring-loaded machine feet - Optional: Bilz air springs for an additional €7,000

Condition: excellent (used), Year of construction: 2014, Hydraulic Press Bunorm 4S-500 Manufacturer: Bunorm AG Hfedpfx Afoxfl Axsijn Model: 4S-500 Year of Manufacture: 2014 Pressing Force: 500 kN Maximum Pressure: 225 bar Weight: 3,200 kg Electrical Connection: 3×400 V + N + PE Frequency: 50 Hz Protection: 20 A Control System: Siemens Simatic HMI Touch Safety System: SICK C4000 Light Curtain SCOPE OF DELIVERY Includes, among others (non-exhaustive list): Hydraulic Press Bunorm 4S-500 Exact scope of delivery as shown in the photo series. The Bunorm 4S-500 hydraulic press impresses with its robust construction and a pressing force of 500 kN at a maximum pressure of 225 bar. With its solid build and a weight of 3,200 kg, the press is suitable for demanding production applications. The integrated Siemens Simatic HMI Touch control system enables precise and user-friendly operation. Thanks to the modern SICK C4000 light curtain safety system, a high level of operator protection is ensured. This machine is the ideal solution for companies that value reliability, precision, and safety. No guarantee is given for the correctness, completeness, or currentness of the information provided.

Condition: as good as new (ex-display), Year of construction: 2024, new heating plate press, hydraulic ITALPRESSE type XL/6 30-13 with gold anodized plates Touch display control - electric heating plates 3.000 x 1.300 mm - Total pressure 90 to. - Number of heating plates 2 pcs. - Number of shelves 1 pc. - Cylinder stroke 350 mm - Shelf opening 350 mm - Loading from all sides - Number of impression cylinders 6 pcs. - Diameter of pressure cylinders 85 mm - Power requirement of hydraulic unit 3 kW - Electric heating plates made of solid hard aluminum with built-in heating wires - Heating capacity 22 KW - High-pressure insulating plates - Working temperature 90° C. - max. temperature 120° C. - Operating voltage 400 V/50 Hz - Safety regulations according to CE standard Standard equipment: - Movement of the press table with rack and parallel guides at 2 corners of the press table made of self-lubricating material - Touch screen electronic control unit for controlling and monitoring the machine - Digital timer for setting the pressing time and automatic opening - Digital input and monitoring of the pressing pressure - Digital timer for setting the pressing time - Digital diagnosis and display of fault messages - Safety circuit with two-hand operation - Safety rip cord - Safety bracket for lower pressing table Integrated accessories: - Touch Screen TS/400 Hjdpfxedx R Tfj Afiofn - EFC electronic flatness control - Gold anodized heating plates (Busse) Location: From stock 54634 Bitburg - immediately available-

Year of construction: 2012, condition: ready for operation (used), This MILLUTENSIL Mil 303 hydraulic press was manufactured in 2012. It features a usable table of 3000 mm by 2000 mm, with a maximum load capacity of 30,000 kg on the upper table and 70,000 kg on the lower table. The press operates with a total power of 31.1 kW and offers adjustable hydraulic pressure up to 240 bar. Consider the opportunity to buy this MILLUTENSIL Mil 303 hydraulic press. Contact us for more information. Application Types Bending Hfedpfx Ajxnr Dhofijn

Condition: used, Working width 3500 mm Working height 2550 mm Number of cylinders 6 St. loading dimensions L x W x H 4500x950x2900 mm Hfedpfexnqw Tsx Afien Hess Speedy frame press ----- will be checked Insertion dimension / pressing length max. 3,500 mm Insertion dimension / pressing height max. 2,550 mm Sliding carriage for width adjustment locking in 50 mm Double hole grid system Electric height adjustment of the long-stroke cylinders (hydraulic) Insertion height of the abutment plates can be preselected in 4 positions 3 vertical printing cylinders stroke 1000 mm Pressure force per cylinder 2000 kN / 20000 N 3 horizontal printing cylinders stroke 80 mm Pressure force per cylinder 1250 kN / 12500 N Printing plate depth 100 mm width 140 mm Grid for cylinder fixation/rear bearing 50 mm Medium pressure beam with shut-off valve Final pressure switch-off and pressure control Control and pressing process in touch button operation Adjustable pressing pressure min. 25 – max. 160 bar Electrical connection 2.2 kW / 400V Image and video not original, show identical model ----- (technical data according to the manufacturer - no guarantee!)

Year of construction: 2013, condition: excellent (used), 1. SCOPE OF SERVICES - EBU H 12 FT Eccentric press - Siegfried SPC control unit 2. DOCUMENTATION - Complete operating documentation available 3. TECHNICAL DATA Hfjdofrzlmjpfx Afisn Year of construction: 2013 Type: Eccentric press Nominal force: 120 kN Max. mould installation height: 170 mm Max. weight of upper mould part: 25 kg stroke adjustment range: 30 mm ram height adjustment: 40 mm Stroke rates: 40-200 1/min Pneumatic operating pressure: 5.5/10 min/max bar Electrical connection: 400 VAC, 50 Hz Weight: 1200 kg

Condition: excellent (used), Year of construction: 2016, LAMELLA – CASE CLAMP PRESS GANNOMAT “CONCEPT 70 ECO” Complete in standard configuration including: - Sturdy, torsion-resistant steel frame, constructed with welded and bolted assemblies - UPPER lamella pressure beam with 6 elements, SIDE lamella pressure beam with 5 elements - Lamella pressure beams feature the tried-and-tested tolerance compensation system (Ganner system) for tightly pressed carcass joints - Counter-pressure surfaces (side pressure wall, bottom) are 38 mm thick, coated, continuous support plates - Continuous pressing surface with a height of 95 mm on the lower vertical pressure beam - Electromotive adjustment of both pressure beams via precision trapezoidal thread spindles (with increased pitch and concentricity accuracy) and high-performance lead nuts with grease reservoir - Clamping is electromotor-driven, with two separate worm gear motors (2 x 0.75 kW) - The pressing force of the pressure beams is continuously adjustable electronically using two potentiometers and regulated via frequency inverters, providing a completely wear-free press force control - Pressing force for horizontal beam: min. 500 daN (kg) up to stepless max. 2200 daN (kg) Hjdjw Td A Ispfx Afiefn Pressing force for vertical beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Press and adjustment speeds of the pressure beams with fine positioning, switchable via 3-stage selector: 5 / 10 / 25 mm/sec - Extremely user-friendly operation - Working height/loading height: 300 mm - Working dimensions: Length min: 150 mm, max: 2500 mm; Height min: 150 mm, max: 1400 mm; Depth: 700 mm - Machine No. 563.624 - 400V, 3Ph, 50Hz (3.2 kVA, 16 A) Set of machine feet for 500 mm working height Operating manual in German Overhauled by Ganner, with 6-month parts warranty Location: ex stock 54634 Bitburg - Immediately available -

Condition: ready for operation (used), Year of construction: 2018, General Data Measurements width 1340 mm Measurements depth 1900 mm Measurements height 2380 mm Machine weight 3300 kg Main Drive Pressing force 360 kN Bending length 1020 mm Stroke 120 mm Movement Y-Axis Rapid Traverse 25 mm/s Hedpfsxnr E Sox Afisfn This TRUMPF TruBend 7036 press brake was manufactured in 2018. It features a press force of 360 kN and a bending length of 1020 mm. The machine includes a Touchpoint TruBend operating interface and offers a maximum stroke of 120 mm. Dimensions are 1900 mm in length, 1340 mm in width, and 2380 mm in height, weighing 2600 kg. If you are looking to get high quality bending capabilities consider the TRUMPF TruBend 7036 machine we have for tact us for more information. Application Types Bending

Condition: excellent (used), Hess Corpus Press Type: Export, Pneumatic Manufacturer: Hess Hodpfxsxgvwpe Afijfn Type: Export Maximum workpiece size: 2,500 x 1,500 mm Press force: 1,400 kp pressing capacity per pressure unit at 15 bar Vertical cylinders: 2 + 2 pressure cylinders Horizontal cylinders: 2 + 2 pressure cylinders Dimensions: 3,900 mm x 2,500 mm x 600 mm Weight: 1,060 kg Hess Corpus Press Export, pneumatic 2 vertical pressure assemblies, each with 2 pressure cylinders, 80 mm cylinder diameter, 110 mm stroke, 1,400 kp pressing force per pressure unit at 15 bar 2 horizontal pressure assemblies, each with 2 pressure cylinders, 80 mm cylinder diameter, 110 mm stroke, 1,400 kp pressing force per pressure unit at 15 bar; the upper unit is easily adjustable thanks to weight compensation Pressing operation is controlled via 2 rotary slide valves with positions Press – Stop – Release Maintenance unit consisting of pressure regulator (0–15 bar), pressure gauge, and oil mist lubricator Anodized measuring scales, detachable feet Location: Ex works customer site - Immediately available -

Condition: as good as new (ex-display), Year of construction: 2024, Technical data: Slat carcass press from our showroom; Working range: width from 150 - 2.550mm, height from 150 - 1.400mm; depth from 150 - 700mm; Variable pressing force adjustment 300/700/1100/1400/1800/2200 dN(kg) of the lateral pressing beam; Variable pressing force adjustment 500/800/1200/1500/1900/2200 dN(kg) of the upper pressing bar Hfsdpfjb Eln Djx Afisn Simple operation via 6 separate push buttons, Freely adjustable pressing time preselection with automatic opening, Charging height 300 mm Machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg

Year of construction: 2025, condition: new, Vacuum membrane press VPR-3500 is a universal Press for the wood processing and thermoforming. The VPR-3500 press is also adjustable and mobile. Usage possibilities: Veneers / form gluing / wrapping... Coating of different profiles (veneer, paper, plastic...) Wood bending: Production of bent and glued components Vakkumsystem: work surface with vacuum channels for a uniform Unterdruckauch for large workpieces. Hjdpfxsd Ecc Tj Afiefn Becker Vakkumpumpe / oil free / tank capacity 100 l Work surface: 3500x1500mm Pump output: KW 0.75 Vacuum pump flow rate: 40 m3/h Rubber membrane Dimensions exterior: 3600 x 1650 x 1000 mm Weight: 400 kg Location: Off the shelf 54634 Bitburg -free load-

Condition: new, Year of construction: 2025, TECHNICAL DATA Pressing force 30t max. load prism jaw 7.5t piston stroke 160mm piston travel 550mm Dimensions and weights length (product) approx. 1240mm width/depth (product) approx. 650mm Height (product) approx. 1920mm Hsdji Amnpopfx Afijfn Weight (net) approx. 280kg Clear width 790mm Installation height max. 1030mm Frame depth 200mm SCOPE OF DELIVERY 2-part prism set for inserting round material Hand and foot lever Winch for lifting and lowering the table Location: Ex works - available at short notice -

Condition: new, Year of construction: 2024, Super special price, as it was on display at our in-house exhibition. Operating hours: 2 Available immediately - subject to prior sale If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Hodpfx Aolht H Esfiefn Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg

Condition: new, Year of construction: 2025, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Hsdpfx Aew Sgnkofiofn Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice

Condition: excellent (used), Year of construction: 2013, LAMELLAR - CASE CLAMP GANNOMAT "CONCEPT 70 ECO" Complete in standard configuration with: Case joints. - Counter-pressure surfaces (side pressure wall, base) are 40 mm thick, coated, continuous support plates - Electrically operated adjustment of both press beams via precision trapezoidal-thread spindles (with increased lead and concentricity accuracy) and high-performance running nuts with grease reservoir. - Clamping is performed electrically using two separate worm gear motors (2 x 0.75 kW) - Pressing force: 2000 daN (kg) per press beam. - The pressing force of the press beam is electronically regulated and set via frequency converter, thus torque transmission is completely wear-free. - Pressing and adjustment speed: 25 mm/sec. - Very simple operation via 6 separate push buttons; 6 movement operations can be selected via the controller. - Freely adjustable pressing time preselection with automatic opening: 0-30 min (switchable to seconds or hours). - Working height/feeding height: 300 mm - Working dimensions: Length min: 150 mm, max: 2550 mm; Height min: 150 mm, max: 1400 mm. Depth: 700 mm 1 selector switch for variable pressing force: 1000 / 1500 / 2000 daN (kg) Machine No. 380.324 400V, 3Ph, 50Hz (2.5 kVA, 16 A) Set of machine feet for working height 500 mm Machine used: Year of construction: 2013, fully overhauled by Ganner, 6-month parts warranty Special price: ex-stock 54634 Bitburg Hodpfx Afow Tdymsiefn - immediately available -

Condition: new, Year of construction: 2025, AL-KO POWER UNIT® 300 P-BP 30 -50 Intake port : 300 mm nominal motor power : 7,5 kW / 3 Ph Voltage: 400 V / 50 Hz Maximum volume flow : 6000 m³ / h Nominal volume flow : 5.089 m³ / h Negative pressure 2.587 Pa Hfsdoh D If Hjpfx Afien Filter area 30 m² Dimensions (L x W x H) in mm 3.000 x 1.361 x 2.817 Briquetting capacity 30 - 50 kg / h Briquette diameter: 50 mm Weight: 1570 kg Machine is brand new in our STOCK - IMMEDIATELY AVAILABLE - subject to prior sale Location: 54634 Bitburg

Condition: like new (used), Year of construction: 2025, operating hours: 1 h, Super special price, as it was on display at our in-house exhibition. Hjdjtnz Ttspfx Afiofn Operating hours: 1 Available immediately - subject to prior sale If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg

Year of construction: 2025, condition: as good as new (ex-display), Vacuum - membrane press VP - series are the ideal solution for the wood processing industry. VP 3000 is equipped with heating technology, which reduces the drying time of the adhesive so that the performance is higher. Usage possibilities: Hodjdvltyjpfx Afijfn Veneers / form gluing / wrapping... Coating of different profiles (veneer, paper, plastic...) Wood bending: Production of bent and glued components The heating system is equipped with temperature control Rubber membrane 2.5 mm Table top is made of plastic 12 mm Oil-free Becker vacuum pump 25 m3/h The control system of vacuum / Tankinhalr 15 l Work surface: 3000x1500mm Heating system temperature: Max 60 degrees C Heating system: KW 4,5 Pump output: KW 0.75 Vacuum pump capacity: 25 m3/h Rubber membrane Dimensions exterior: 3100 x 1650 x 1600 mm Weight: 450 kg Location: Off the shelf 54634 Bitburg -free load-

Condition: new, Year of construction: 2025, Gannomat Concept 70 Eco Lamella - carcass press with rapid traverse Technical data: Lamella carcass press from our showroom; Working range: width from 150 - 2.500mm , height from 150 - 1.400mm; depth 700mm; - lamella press beam top with 6 elements, lamella press beam side with 5 elements - lamella press beam with practice-proven tolerance compensation for tightly pressed carcass joints - Counterpressure surfaces are 40 mm thick, coated continuous support plates - The pressing force of the pressing bars is infinitely variable electronically controlled by 2 potentiometers and adjusted via frequency converter, therefore the torque transmission is absolutely wear-free. - Pressing force for horizontal press bars min. 500 daN (kg) to infinitely variable max. 2200 daN (kg) - Pressing force for vertical press bars min. 300 daN (kg) to stepless max. 2200 daN (kg) - Including option: Rapid traverse speed for fast positioning of the press bars, controlled by automatic workpiece recognition with sensors in the press bars, press speed 5/10/25 mm/sec. Hfsdpfx Afsiidm Noien and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Jog mode for precise positioning of the two pressing beams e.g. for low pressing forces, drawers and carcasses 45 degrees. Simple operation via 6 separate pushbuttons, freely adjustable pressing time preselection with automatic opening, loading height 300 mm. Machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2024, Weima Briquetting Press TH 714 The TH 714 machines are designed for plants with required throughput rates of up to 150 kg/h. The stable press housing enables the production of high-strength briquettes - from materials such as wood, polystyrene, foams, light metals, paper or biomass. Numerous additional options can be implemented, e.g. oil cooling for multi-shift operation. All machines are available as left- or right-hand version. Mounting on a stable base frame ensures fast installation and makes mobile use possible. User-friendly operation thanks to Siemens PLC control Hfedpfx Afjil Hggsijn In order to live up to our performance promise, we design and produce all control cabinets ourselves at our Ilsfeld site and equip them with well-known international components. This guarantees highest quality with compact design. The used PLC-control from Siemens is perfectly adapted to the requirements of the briquetting process. Impurity-resistant screw conveyor due to cardanic suspension The screw conveyor, which transports the material into the pre-compressor of the briquetting press, is suspended on a cardan joint. This prevents interfering materials from causing damage to the screw conveyor. As is so often the case, however, it always depends on the specific application which suspension is chosen. For metal applications, for example, we often recommend rigidly mounted screws. Briquette diameter (mm): 70 Throughput capacity up to (kg/h): 150*1 Hydraulic motor (kW): 11 Oil quantity (liters): 250 Weight (approx. kg): 1100 Location: Ex stock 54634 Bitburg - immediately available - subject to prior sale

Condition: new, Year of construction: 2025, AL-KO POWER UNIT® 250 P-BP Intake port : 250 mm nominal motor power : 6,5 kW / 3 Ph Voltage: 400 V / 50 Hz Maximum volume flow : 4.900 m³ / h Nominal volume flow : 3.534 m³ / h Negative pressure 2.451 Pa Filter area 22,4 m² Dimensions (L x W x H) in mm 2.305 x 1.333 x 2.609 Briquetting capacity 30 - 50 kg / h Location: Comes to stock 54634 Bitburg Hfodpfx Ajcdr E Aefion Subject to prior sale

Year of construction: 2025, condition: as good as new (ex-display), Vacuum - membrane press VP - Series are the optimal solution for woodworking. VP 3000 is equipped with the heating technology, which shortens the drying time of the glue, so that the efficiency is higher. Possible applications: Veneer / form gluing / wrapping... Coating of different profiles (veneer,paper, plastic...) Wood bending: production of bent and layer-glued components The heating system is equipped with temperature control Rubber membrane 2,5 mm Table top is made of plastic 12 mm Hsdpfx Ajdwh E Ajfijfn Oil-free Becker vacuum pump 25 m3/h The control system of the vacuum / tank capacity 15 l working area: 3000x1500mm Heating system temperature: Max. 60 degrees C heating system: KW 4,5 Pump capacity: KW 0,75 Vacuum pump flow rate: 25 m3/h Rubber membrane Dimensions outside: 3100 x 1650 x 1600 mm Weight: 450 kg Machine is equipped with a chassis. Location: From warehouse 54634 Bitburg - free on truck -

Condition: like new (used), Year of construction: 2025, operating hours: 1 h, Super special price, as it was on display at our in-house exhibition. Operating hours: 2 Available immediately - subject to prior sale If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hfjdstnz Hbspfx Afion Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg

Year of construction: 1985, condition: excellent (used), Edge gluing press for veneer, solid wood and plastic, model HFK 2200, for trimming edges during press time. When using heat-curing glue, we achieve pressing times of 20 to 30 seconds for veneer edges. Maximum working size approx.: 1,400 x 2,500 mm Heating: 1.7 kW Electro-pneumatic edge press Haug HFK 2200 for pressing edging material onto wood, with heating. Hodpfx Afow Apqqsisfn 3 table extensions Swiveling work table Location: ex stock 54634 Bitburg - immediately available -

Condition: used, Year of construction: 1968, Veneer press Manufacturer: Bütfering Model: 22/11 Year of manufacture: 1968 Plate size: 2.2 x 1.1 m Note: Heating plates no longer function – therefore very inexpensive Has been used as a cold press 4 cylinders Cylinder stroke: 360 mm Hfsdpfsw Nbztox Afien Hydraulic Location: ex stock 54634 Bitburg - immediately available -