Used Grease for sale (504)

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. Cjdpfxsx Dnb Us Abbogn • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see our video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: used, functionality: fully functional, Year of construction: 2019, operating hours: 8,500 h, load capacity: 10,000 kg, lifting height: 16,200 mm, fuel type: diesel, construction height: 3,900 mm, power: 185 kW (251.53 HP), empty load weight: 39,820 kg, drive type: Diesel, construction width: 4,150 mm, Empty container reachstacker Transmission: Dana TE17300 series Condition: Ready for operation and fully functional Technical condition: Very good Front tyre size: 14.00-24 Csdpfxsx S Sqls Abbsgn Rear tyre size: 14.00-24 Central greasing system, rear view camera, air-cushioned driver's seat

Condition: used, Year of construction: 2003, max. grinding diameter 5-50 mm grinding length 350 mm workpiece length 50-300 mm diameter 5-50 mm current capacity 70 kVA weight of the machine ca. 9 t dimensions of the machine ca. 3300x2950x2400 m Power supply: 400 V/50 Hz Power: 70 kVA Fuse protection: 3X125A Conductor cross-section: 5X25 mm² Cu Workpiece diameter: ? 5-? 50 Workpiece length: 50-300 - Manual loading and unloading - External fully automatic loading device - Workpiece spindle stock fixed on grinding table Workpiece spindle unit: Dimensions: ? 135 x 400 mm Lubrication: Permanent grease lubrication Bearing seal: With sealing air Drive: with HF motor Special mount: Junker standard collar ?75 mm Max. speed: 6000 min. -1 Tailstock: Longitudinal adjustment: manual Turning center: Junker standard collar ? 48 mm (?75 mm) Grinding table: Feed: Z-axis Grinding headstock: Feed: X-axis Horizontal swivel: B-axis HF grinding spindle unit I, II, III Dimensions: ? 165 x 350 mm Flange: ? 190 mm Standard collar: ? 127 mm Cjdpfx Aeyan R Nobbjgn Lubrication: Permanent grease lubrication Bearing seal: With sealing air Drive: 8 kW Balancing: Electronic Speed max. 8800 min -1 Grinding wheel I, II, III Type: Borazine (CBN) ceramic bonded Diameter: ? 350 mm Bore: ? 127 mm Coating width: max. 5 mm (standard) Peripheral speed: max. 140 m/s

Condition: used, Year of construction: 1989, Universal Milling Machine ALCERA type 100 M Travel X: 1000 mm Travel Y: 450 mm Travel Z: 600 mm Cone SA40 Spindle speed: from 40 to 2000 RPM Table size: 1400 x 320 mm Year of construction: 11/1989 Scale 3 axes HEIDENHAIN Centralized grease pump Feeds: auto X - Y - Z Joystick command Lubricant pump Voltage: 380 V Codpox Ekafofx Abbegn Width: 2100 mm Depth: 2400 mm Total height: 2000 mm Weight: approx 3 T

Condition: like new (used), Year of construction: 2023, functionality: fully functional, travel distance X-axis: 4,970 mm, travel distance Y-axis: 2,120 mm, travel distance Z-axis: 250 mm, rapid traverse X-axis: 60 m/min, rapid traverse Y-axis: 60 m/min, rapid traverse Z-axis: 30 m/min, feed rate X-axis: 60 m/min, feed rate Y-axis: 60 m/min, feed rate Z-axis: 30 m/min, spindle speed (min.): 600 rpm, spindle speed (max.): 20,000 rpm, spindle motor power: 12,000 W, number of slots in tool magazine: 24, mount diameter: 350 mm, tool weight: 8 g, input voltage: 400 V, type of input current: AC, Equipment: documentation/manual, Complete machine, with Coral filter system and SCM lifter for sale. The equipment has very little use. Numeric control machining centre, with mobile gantry and fixed worktable for the processing of solid wood and various types of materials: glued laminated timber, plywood, chipboard, MDF, Aluminium etc. Designed using the best three-dimensional solid modelling systems, the structure is composed of a machine bed and a mobile gantry made of electro-welded steel. Component's milling of machine bed are performed on high quality CNC machining centres, with one single positioning operation, in order to guarantee the very best planarity, perpendicularity and precise tolerances. The control unit is a numeric control interfaced with an industrial PC. The CNC solution with PC combines all of the qualities of numeric controls with the user-friendliness typical of personal computers. The PC allows to use the operator interface Maestro cnc, developed by SCM to make machine programming fast and simple even for the less skilled operator. Technical specifications: - drilled and tapped holes spaced 120x120 mm for vacuum connection of jigs and equipment fitting - groove scheme spaced 40 mm for suction cups or rubber gaskets - n. 2 working areas - max. dimension to work in Y direction = 2170 mm TELESOLVE teleservice via internet Mobile console with "eye-M PRO" integrated PC TECPAD - Remote machine control Mobile console with 7" touch-screen color monitor for control and management. Csdpfxswd Nrde Abbegn PRISMA KT Machining Head The machining head with 5 interpolating axes, fixed directly to the mobile gantry, guarantees maximum strength during routing operations and provides top finishing quality also with high stock removal. Technical specifications: Routing unit with 5 interpolating axes − electro-spindle with HSK 63F quick release tool-holder − Rotation speed 600-20000 rpm − right and left rotation − max power (S1/S6) 11/12 kW (15/16.5 HP) from 9000 rpm − Inverter − C-axis rotation = 640° − B-axis rotation = 270° − C-axis equipped with TTS locking system (Total Torque System – SCM Patent) − "For Life" grease lubrication − liquid cooling with heat exchanger - Automatic dust extraction hood with four positions and ON-OFF by workpiece program. Two 250 (300) m3/h - 50 (60) Hz vacuum pumps Vacuum pump for each half-table. Independent vacuum circuit for each half-table. PRO-SPACE Safety system – full protection of the machining head with anti-ejection strips curtains and bumpers with emergency sensors - Emenency cable in the operator area - rear and side protection along the perimeter Enclosed cable-holder chain MAESTRO ACTIVE Human-Machine interface software (HMI) Maestro active is the new interface software (HMI) which has been unified across all SCM technologies. A single operator can easily and confidently run multiple SCM machines, reducing operator training times and facilitating entry into production. Windows 10 embedded 64 bit operating system Maestro cnc programming software MAESTRO CNC SOFTWARE SUITE – USER INTERFACE AND PROGRAMMING Advanced nesting free-form + Label module for Maestro cnc Rapid 24 - Rear Tool store Circular tool store anchored to the mobile gantry. Max load 96 kg

Condition: excellent (used), Year of construction: 1998, Used cnc horizontal milling boring machine Brand: AYCE Model: AC100-k4 Serial number: 740 Year: 1998 Power: 16kw Weight: 12,700kg AC100-K4 MODEL WITH CONTINUOUS ADVANCE VARIATION Numerical control: Heidenhain TNC124 with 4 axes (X, Y, Z, B) Csdjizxbiopfx Abbogn Number of bench supports: 4 (K4) OPTIONALS: - Cnc Heidenhain - Automatic positioning of the table rotation 4 x 90º. - Vertical course 1200mm (Instead of 1000mm that the standard model has) - Refrigeration equipment - Face plate and clamping arm - Universal vertical apparatus, Huron type with hydraulic tool clamping - Rest for vertical course of 1200mm - Table rotation display 4th AXIS (B) Principal axis: - Shaft diameter: 100mm - Inner cone: ISO 50 with quick tool clamping (Instead of Morse 5) - Drill mounting diameter: 171.45mm - Horizontal course of the main axis: 700mm - Vertical course of the main axis: 1200mm - Number of turning speeds: 18 - Speed range: 12-1200 rpm - Maximum distance between plate and steady rest: 2250mm Advances: - Number of work advances in all directions: INFINITE - Min/max value of work progress: 2 - 1500 mm/min. - Rapid advances in carriages and head: 3000 mm/min. - Rapid advance main axis: 1500 mm/min. - Rapid table rotation advance: 600 degrees/min. Rotary table: - Turntable dimensions: 1100x1200mm - Table longitudinal course without steady rest: 1500mm - Curos longitudinal table with lunette: 1200mm - Cross course: 1700mm - Distance between axis/maximum table center without steady rest: 1975mm - Distance between axis/maximum table center with steady rest: 1600mm Automatic centralized greasing. Hardened and rectified guide. Telescopic guide protectors. Ball screws in the 3 axes. Automatic hydraulic locks in all movements.

Condition: used, functionality: fully functional, Year of construction: 2004, operating hours: 15,950 h, load capacity: 45,000 kg, lifting height: 14,700 mm, fuel type: diesel, drive type: Diesel, Full container reachstacker Load center: 1900 Condition: Limited operational readiness Technical condition: normal Front tire size: 18.00-33 Rear tire size: 18.00-33 20-40 ft topspreader + piggy-back Csdpex Sz I Tefx Abbsgn Hydraulic sliding cabin, central greasing, rear view camera

Condition: good (used), power: 135 kW (183.55 HP), fuel type: diesel, color: green, Year of construction: 2007, operating hours: 12,287 h, Year of manufacture: 2007 Drive: Wheel Empty weight: 27.500 kg Dimensions (LxBxH): 1110 x 275 x 330 cm Technical condition: good Serial number: 825.0.1055 Please contact Ferdinand Pater for more information Csdpfx Abjt Dlxksbsgn Stock no. D33 Machine Brand Sennebogen Type: 825M D-series Weight: 28 Ton Serial number: 825.0.1055 Building year: 2007 Worked hours: 12287 Engine: Deutz TCD 2012 L06 2V 135kW Engine no. 10371260 Boom: K13 configuration, Boom = 7,4 m. and Stick = 5,8 m Safety check valves on boom and stick cylinders Cabin: Maxcab D270, Hydraulic Cab Riser, 2,7 m. in height. Upper carriage: Standard Sennebogen color, central greasing system Undercarriage: Mobile MP26, 4 points outrigger, 8 full rubber tires 10.00-20 Lights: Several lights on boom, stick and cabin Extra: Generator set Dimentions: LXBXH 11,10X2,75X3,30

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Cgjdpfxox A U Nce Abben Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: refurbished (used), Year of construction: 2012, machine/vehicle number: R-00558, load capacity: 260 kg, arm reach: 3,100 mm, controller manufacturer: R-30iA B-Size, teach pendant manufacturer: A05B-2518-C202#EGN, Refurbished FANUC M-900iA/260L manufactured in 2012.12. The robot comes with an R-30iA B-Size controller including iPendant.   Our experts extensively tested the robot, after which we conducted a maintenance service according to the manufacturers’ specifications. The grease is examined for the amount of iron particles, indicating the corresponding axes' condition. Only robots in excellent mechanical condition will be completely refurbished, ensuring a long-term solution for our customers. This enables us to deliver our robots with a warranty term of 12 months as standard!   Brand: FANUC Model: M-900iA/260L Model Number: A05B-1327-B503 Year of Manufacture Robot: 2012.12 Warranty term (months): 12   Payload (kg): 260 Cgsdpjx R Tpyefx Abbsn Reach (mm): 3100 Repeatability (mm): ± 0.3 Controlled Axes: 6-axis Installation Type: Floor, Upside-down, Wall, Angle Mount Weight (kg): 1720   Controller: R-30iA B-Size Year of Manufacture Cabinet: 2012.12 RCC Length (m): 7   Teach Pendant: A05B-2518-C202#EGN Teach Pendant Cable Length (m): 10

Condition: like new (used), Year of construction: 1991, functionality: fully functional, overall weight: 35,000 kg, pressing force: 250 t, type of input current: three-phase, power: 30 kW (40.79 HP), punching force: 250 t, input voltage: 200 V, Equipment: documentation/manual, safety light barrier, AIDA NC2-250(1) 250t eccentric press in excellent condition /ctA2/ Manufacturer: AIDA Type: NC2-250(1) Push force: 160t Year of manufacture: approx. 1991 Stroke length: 170mm Distance above table: (adjustable) 280-400mm Table size: 2700x760mm Bear size: 2100x700mm Electrical power: 3x200V(!!), 30kW - Japanese standard Cjdpfju Dxb Tjx Abbogn Net weight: 35000kg Size: 2760x2800x3980mm Automatic greasing system. Automatic cutting oil dosing - RAZIOL EST-02 Optionally with disc winder and straightener.

Year of construction: 1978, condition: reconditioned (used), Planer thicknesser 600 mm, planing width 600 mm, planing height 180 mm, 3-knife cutterhead, cutterhead diameter 125 mm. Fully overhauled, technically sound and ready for operation. New electrical system, all required lubrication points present. Cast iron body, weight 890 kg. Foldable tables, table height adjustable. Grease nipples at all necessary locations. Cgodpeyabltefx Abbsn

Condition: new, Year of construction: 2024, Many of our machines are available from stock. Call and ask to find out more. Fiber laser cutting machine FLV-T-6035 3kW Specifications - Positioning accuracy of the X and Y axes:: ±0.05mm/m - Repeatable positioning accuracy of the X and Y axes: ±0.03mm - Maximum acceleration: 0.0G - Nominal power: 3.0kW - Energy requirements: 24.0kW - Source brand: Raycus or MAX Photonics (You can choose) - Feed voltage: 3x400V50Hz - International Protection Rating: IP54 Cutting thickness - Carbon steel: Recommended thickness 20.0mm, maximum thickness 22.0mm - Stainless steel: Recommended thickness 8.0mm, maximum thickness 10.0mm - Aluminum: Recommended thickness 6.0mm, maximum thickness 8.0mm - Brass: recommended thickness 5.0mm, maximum thickness 6.0mm Structure parts The machine is very stable thanks to its welded construction based on massive legs. The high speed of head movements while maintaining high precision is ensured by Japanese Fuji servo motors. ABLS - automatically replenishes grease in guides. RayTools cutting head with autofocus Optional extra - Otinus Protect to guarantee your peace of mind This product ensures protection for the source of your laser. With this service you will ensure that the continuity of your business is protected. We will secure your business so that you can complete your orders on schedule. Optional extra - Voltage stabilizer Control panel Operation of the fiber laser cutter is run by the control panel, which consists of a screen, mouse and keyboard. The computer runs Windows 10 and CypCut software. Cjdethh Nxepfx Abbogn All installed software has lifetime licenses. Wireless controller included. Assistance by a specialist We are committed to staying in continuous contact with our customers; therefore, we meet this challenge by offering a time-package of hours to be used for the Otinus Professional Assistance to each machine purchased. Otinus Academy By purchasing this machine you will gain a year's access to online courses that will allow you to effortlessly train a new employee or refresh your knowledge from training! Technical consulting We have specialists who, before the purchase, will select the right machine and accessories based on technical drawings of the parts you plan to make. Price-included 2-day training with machine installation - 1st day (up to 8 hours) – machine commissioning and controller usage training - 2nd day (up to 8 hours) – work under the guidance of our technician – the possibility of programming specific parts that are manufactured at your site Consultation with a specialist - Telephone: 7.30 a.m. to 9 p.m. (Mon-Sat) - time package of 8 hours to be used within 12 months. Online: from 7.30 a.m. to 2.30 p.m. (Mon-Fri) - time package of 8 hours to be used within 12 months. Access to Otinus Academy courses - LibreCad - 12-month access In addition, you will receive - CAD drawing package

Condition: new, Year of construction: 2025, functionality: fully functional, 5 AXIS Machining Center 2131 X, Y, 2100 X 3100MM MOVEMENT RANGE Z AXIS RANGE 1000 MM FOR 5 AXIS HEAVY MACHINES HITECO 17KW S6 TILTING/ROTATION HEAD KIT AXIS RANGE A= +- 185°, C= +- 320°, ORBITAL K PLUS PX-2 15/12 63F NC HSK63 OMRON AC SERVO DRIVE KIT OSAI OPENKEY INDUSTRIAL REAL TIME CONTROL SYSTEM Cjdpfou U Hmpox Abbogn EUCHNER HBA-103037 MANUAL MANIPULATOR CONTROL CABINET AIR CONDITIONING LINEAR MAGAZINE 18 POSITION 16 POSITION HSK63F TURRET MAGAZINE CORRECTION MAP RENISHAW TS27R TOOL MEASURING PROBE SKF AUTOMATIC CENTRAL SOLID GREASE LUBRICATION

Condition: new, Year of construction: 2025, HARDLINE MACHINING CENTER WORKING AREA 1300X1500MM. Z-AXIS WORKING RANGE 300MM OMRON SERVO AC HIGH SPEED DRIVES 1.5kW T-SLOT TABLE FOR M10 MOUNTINGS - MADE OF SOLID STEEL OSAI OPENSMART INDUSTRIAL REAL-TIME CONTROL SYSTEM, ETHERCAT COMMUNICATION EUCHNER HBA-103037 MANUAL MANIPULATOR Cgsdpfx Aeu U Hh Tebbsn CONTROL CABINET AIR CONDITIONING HSD MAX18KW S6 ES789L ELECTRIC SPINDLE KIT - H6161H1501– ATC, UP TO 24,000 RPM ENCODER FOR ATC HSD ELECTRIC SPINDLE ACTIVE COOLING SYSTEM - CW-6000 CHILLER 12-POSITION LINEAR MAGAZINE TOOL LENGTH SENSOR RENISHAW TS27R TOOL MEASURING PROBE TOOL PRESENCE SENSOR PREMIUM COOLING MIST FREEZE NOZZLE SKF AUTOMATIC CENTRAL SOLID GREASE LUBRICATION REMOTE SERVICE ACCESS (REMOTE DIAGNOSTICS) Option for threading and drilling in aluminum and steel

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Bale Size: 400mm x 400mm x... 2. Container Dimensions (Width x Length x Height): 1.000mm x 2.000mm x 800mm 3. Capacity: 4 tons/hour (Steel), 5 tons/hour (Copper), 2 tons/hour (Aluminium) 4. Cycle Time: 90 seconds ( Idle ) 5. Top Cover Cylinder Thrust: 90 tons 6. Preliminary Compression Cylinder Thrust: 150 tons 7. Main Compression Ram Thrust: 210 tons 8. Maximum Working Pressure: 300 bars 9. Electric Motor: 37 kW 10. Machine Dimensions (Width x Length x Height): 3.400 mm x 6.800 mm x 3.000 mm 11. Machine Weight: 18.000 kg 12. There will be an ejection door. 13. Repairable and four-edge-usable blades. Cedpfx Abedfc Iyjbjgn 14. Container walls will be covered with HARDOX 450 - 500 material. 15. There will be an automatic SKF liquid lubrication system integrated into the compression chamber. 16. There will be an automatic SKF greasing system that will grease the bushings. 17. Piston shafts will be induction-hardened and chrome-plated. 18. Pumps and valves used in the hydraulic system will be by PARKER or EATON VICKERS & KAWASAKI brand. 19. Bypass filter will be added to the hydraulic system. 20. There will be an AKG Hydraulic Oil Cooling System. 21. All electrical parts will be SIEMENS or SCHNEIDER Brand. 22. The machine will be fully automatic with PLC control, PLC brand and model will be SIEMENS. There will be a touch screen SIEMENS HMI Simatic Panel with emergency buttons placed on some important points. 23. There will be blades from 2767 material (hardness 55HRC) at the borders of the top cover and the sides of the scrap chamber. 24. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for 1 year or 2.500 working hours whichever comes first against manufacturing defects.

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW Cgjdpfx Asgwa T Rjbbjn 1. Bale Size: 500mm x 500mm x... 2. Container Dimensions (Width x Length x Height): 2.000mm x 2.500mm x 1.100mm 3. Capacity: 15-20 tons/hour (steel) 4. Cycle Time: 90 seconds ( Idle ) 5. Top Cover Cylinder Thrust: 90 tons 6. Preliminary Compression Cylinder Thrust: 150 tons 7. Main Compression Ram Thrust: 300 tons 8. Maximum Working Pressure: 300 bars 9. Electric Motor: 2 x 75 kW = 150 kW 10. Machine Dimensions (Width x Length x Height): 10.000 mm x 10.000 mm x 4.000 mm 11. Machine Weight: 55.000 kg 12. There will be an ejection door. 13. Repairable and four-edge-usable blades. 14. Container walls will be covered with HARDOX 450 - 500 material. 15. There will be an automatic SKF liquid lubrication system integrated into the compression chamber. 16. There will be an automatic SKF greasing system that will grease the bushings. 17. Piston shafts will be induction-hardened and chrome-plated. 18. Pumps and valves used in the hydraulic system will be by PARKER or EATON VICKERS & KAWASAKI brand. 19. Bypass filter will be added to the hydraulic system. 20. There will be an AKG Hydraulic Oil Cooling System. 21. All electrical parts will be SIEMENS or SCHNEIDER Brand. 22. The machine will be fully automatic with PLC control, PLC brand and model will be SIEMENS. There will be a touch screen SIEMENS HMI Simatic Panel with emergency buttons placed on some important points. 23. There will be blades from 2767 material (hardness 55HRC) at the borders of the top cover and the sides of the scrap chamber. 24. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for 1 year or 2.500 working hours whichever comes first against manufacturing defects.

Condition: new, Year of construction: 2025, IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Electric Motors Total Power: 180 kW 2. Machine Weight: 20.000 kg 3. Shredding Capacity: 10 t/h (Steel) 15 t/h (Copper) 4. Blade Quantity: 90, Blade Thickness: 100 mm. 5. Loading Chamber Dimensions: 1.600 mm x 2.400 mm 6. Shredding Chamber Dimensions: 1.000 mm x 1.600 mm 7. Replacement and maintenance of the blades can be easily done from the top of the chamber. 8. Cutting blades are made of material No: 2767 9. Main shafts are made of material: 42 CrMo4, 32-34 HRC (Twisting and breaking resistant ) 10. All chamber walls will be covered with anti-wearing armor steel material HARDOX 500. 11. All static blades and distance rings will be made of HARDOX 450. 12. Speed: 4 – 6 rpm 13. The movement power of shafts will be provided by four planet reductors which are driven by four power-controlled bi-directional hydro motors. Hydraulic equipment will be PARKER brand or BOSCH-REXROTH. 14. There will be hydraulic oil and reducer oil cooling units separated from each other. 15. Each shaft will be able to move independently from each other. 16. The loading of the shredder can be done by crane 17. The machine will stop itself with an acoustic warning with the help of security sensors which are going to protect the machine against any harm. Cgjdpfxogwcc Ao Abbon 18. There will be an automatic grease oiling system to keep bearings oiled automatically. 19. All electrical parts will be SCHNEIDER and SIEMENS brand. 20. The machine will be fully automatic with PLC control. There will be a touch screen on the control panel which will provide easy access to machine settings and process monitoring. 21. The machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) operation hours. 22. The machine is CE certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements.

Condition: new, Year of construction: 2025, 1. Electric Motors Total Power: 360 kW 2. Machine Weight: 44.000 kg 3. Shredding Capacity: 10 - 15 tons/h (Iron & Steel) 4. Blade Quantity: 78, Blade Thickness: 150 mm. 5. Loading Chamber Dimensions: 2350 x 4085 mm 6. Shredding Chamber Dimensions: 1500 x 2000 mm Cedpodfc Uzjfx Abbogn 7. Replacement and maintenance of the blades can be easily done from the top of the chamber. 8. Cutting blades are made of material No: 2767 9. Main shafts are made of material: 42 CrMo4, 32-34 HRC (Twisting and breaking resistant ) 10. All chamber walls will be covered with anti-wearing armor steel material HARDOX 500. 11. All static blades and distance rings will be made of HARDOX 450. 12. Speed: 4,5 – 6 rpm 13. The movement power of shafts will be provided by four planet reductors which are driven by four power-controlled bi-directional hydro motors. Hydraulic equipment will be PARKER brand or BOSCH-REXROTH. 14. There will be hydraulic oil and reducer oil cooling units separated from each other. 15. Each shaft will be able to move independently from each other. 16. The loading of the shredder can be done by crane 17. The machine will stop itself with an acoustic warning with the help of security sensors which are going to protect the machine against any harm. 18. There will be an automatic grease oiling system to keep bearings oiled automatically. 19. All electrical parts will be SCHNEIDER and SIEMENS brand. 20. The machine will be fully automatic with PLC control. There will be a touch screen on the control panel which will provide easy access to machine settings and process monitoring. 21. The machine will be under Aymas Makina San. Ve Tic. A. S. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) operation hours. 22. The machine is CE certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements.

Condition: used, Central lubrication, oil circulation system, single-line pump, central lubrication unit, grease lubrication pump, piston pump, lubrication pump, oil central lubrication pump -Manufacturer: Vogel, oil central lubrication pump from milling machine Deckel FP4L -Type: MFE 5/S3 -Motor: Type DM 6 60 W -Dimensions: 185/130/H250mm Cgsdsul H Enjpfx Abbsn -Total weight: 5 kg

Condition: good (used), Hose reel, hose unwinder, tank hose reel, wall reel, oil conveyor, hose reel, automatic hose reel, oil hose reel, grease hose reel, grease hose reel -Manufacturer: Consul, grease hose reel -Type: M 095 Cedpfjwbpn Hex Abbogn -Hose length: 8 m -Dimensions: 780/270/H550 mm -Weight: 29.2 kg

Condition: used, Central lubrication, oil circulation system, single-line pump, central lubrication unit, grease lubrication pump, piston pump, lubrication pump, oil central lubrication pump, oil single-line pump Cedpfsm Rk Tpox Abbsgn -Manufacturer: SKF Vogel, OIL- central lubrication pump from Uldrian TSM 22-8 rotary transfer machine -Type: MKU11-KW2-0005 428 -Content: approx. 1.8 l -Flow rate: 0.1 l/min / 16 bar -Dimensions: 220/130/H230 mm -Weight: 3.6 kg

Condition: repair required (used), Central lubrication, oil circulation system, single-line pump, central lubrication unit, grease lubrication pump, piston pump, lubrication pump, progressive pump, central lubrication pump -Handover: in its current condition as inspected -Device condition: not functioning, control board missing -Manufacturer: Lincoln, Quicklub central lubrication pump -Type: 645-41110-1 -Voltage: 100-240 V -Power: 60 watts -P max: 240 bar Cgodpfx Abshv Ilwsbsn -Dimensions: 270/240/H570 mm -Weight: 15.5 kg

Condition: good (used), Lubricating bolt for rope pulley, steel rope pulley, rope deflection pulley, crane rope, four-rope orange peel grapple, polyp grapple, mechanical orange peel grapple, shell grapple, ship unloading grapple, scrap grapple, garbage grapple, rope grapple, digging grapple, bolt crane bolt, lubricating bolt -Grease bolt: crane bolt type 75x145 M48 -Shaft: Ø 59.6 mm .: 1045 1707 -Number: 10x bolts available -Price: per piece -Dimensions: Ø 80 x 150 mm Cgodpfx Absv Ilc Iebjn -Weight: 3.4 kg/piece

Condition: excellent (used), Joint bearing -Inner diameter: 140 mm -Outer diameter: 230 mm Cedpob A H N Tefx Abbsgn -Brite outer ring: 80 mm -Width of inner ring: 130 mm -Grease groove -Weight: 18 kg -Number: several available