Used Gear Tester for sale (11,805)

Year of construction: 2023, operating hours: 2 h, condition: used, machine/vehicle number: 5767/78631, Axle distance: approx. 40-175 mm, max. test piece diameter: approx. 200 mm, net weight: approx. 110 kg, adjustable measuring force: approx. 1-11 N, power consumption: approx. 0.2 kW, control/switch FRENCO, serial number: 30020-000147, various measuring accessories, 1 operating panel, single-track/single-door, 1 DELL flat screen, approx. 22 inches, year of manufacture: 2022 Fodpfx Afsx Aklmsnopb

Condition: used, max. wheel diameter 0-200 mm max. module 25 Fpedpfxotuxa Uo Afnob min. module 0,5

Condition: used, Chroma Type: ATE 17020 The Chroma 17020 is a highly professional, modular test system for lithium-ion & other battery pack qualification. Particularly strong in: - Lifetime testing, BMS verification, and validation of complex charging cycles - High energy recovery – up to 85% efficiency - Flexible expansion through numerous channels or higher current ranges - Enterprise deployment with extensive safety features & data persistence Technical data – Chroma ATE 17020 PTS Feature Specification Model: Chroma ATE 17020 PTS System type: Regenerative battery pack test system (charge/discharge test) Channel output: 600 W to 60 kW (modular and scalable) Total output: Up to 600 kW (depending on configuration) Voltage range: 20 V / 60 V / 100 V / 200 V / 500 V Current per channel: Depending on module: from a few amps up to >300 A per channel Parallel operation: Yes, for higher current up to 2,600 A Current and voltage accuracy: ±(0.05% of reading + 0.05% of range) Power accuracy: ±0.1% Transition time (charge/discharge): < 50 ms Sampling rate (measured data): up to 50 kHz (with BatteryPro) Data logging: Cyclic, 10 μs – 1 s / memory for 60 min power failure Test modes: CC, CV, CP, CC-CV, DCIR, pulse, drive cycle, dynamic profiles Number of channels: Up to 60 channels (expandable) Communication: CAN, S-Bus, Ethernet, USB Software: Chroma BatteryPro (test programming, real-time monitoring) Protection functions: OVP, UVP, OCP, UCP, OTP, reverse polarity, wire loss, delta V/I, etc. Energy recovery: Yes – up to 85% energy efficiency, grid-friendly (THD < 5%) Cooling: Fan cooling, low waste heat due to energy recuperation Temperature monitoring: Optionally integrable, range 0–90°C ±2°C Dimensions & weight: Depending on configuration (e.g. 19″ rack, approx. 300 kg) Mains connection: 3-phase, 400 V AC (depending on model) Applications: E-mobility, battery development, quality assurance, cell research Weight: approx. 455 kg Condition: used Fedpfowwrxaex Afnopb Scope of delivery: (See picture) (Specifications and technical data are subject to change and errors excepted!) If you have further questions, we are happy to assist you by phone.

Condition: excellent (used), functionality: fully functional, Year of construction: 2002, operating hours: 48,651 h, Mazak Space Gear-510 MKII 2.5 kW Year of manufacture December 2002 - after renovation!!! Very good condition! Fpodpfx Aewqr Tdjfneb Meter reading 48651 hours Operating system Fanuc L-64

Condition: excellent (used), Hommel Fedpex Ebuwjfx Afnepb Hommel Tester T1000 Surface Roughness Measuring Instrument – Jenoptik – incl. probe & case Item Description: For sale is a Hommel Tester T1000 by Jenoptik / Hommel-Etamic. The T1000 is a precise portable surface roughness tester that uses a tactile stylus to measure the surface roughness of various workpieces. Measured values such as Ra, Rz, and Rmax are displayed immediately on the screen. An integrated mini-printer additionally allows for direct printout of measurement protocols. The device is suitable for use both in production environments and in laboratories. Technical data: Model: Hommel Tester T1000 Manufacturer: Jenoptik / Hommel-Etamic Measured parameters: Ra, Rz, Rmax, etc. Measuring range: Ra approx. 0.03 – 20 µm Display: LCD screen with direct measurement readout Dimensions: approx. 28 × 20 × 10 cm Power supply: Power adapter 230 V AC → Device 9–12 V DC Weight: Device approx. 1.5 kg, in case approx. 3–4 kg Hommel Tester T1000 External surface roughness probe Two additional stylus probes in cases Power supply Original transport case Connection cable Important note: “The table shown in the photos is not included in the sale.” Condition: used Scope of delivery: (See picture) (Specifications may be subject to change and errors excepted!) For any further questions, please feel free to contact us by phone.

Condition: excellent (used), functionality: fully functional, Year of construction: 2007, operating hours: 41,417 h, Mazak Hyper Gear 510 4.0 kW Year of production February 2007 Meter reading 41417 hours Fpodpfx Afswqr Twjneb MAZATROL operating system very good condition Technical data of the MAZAK HYPER GEAR 510 laser cutter - laser power: 4 kW - feeds in the X/Y/Z axes: 3070/1545/100 mm - dimensions of the work table (length x width): 3000 x 1500 mm - maximum weight of the workpiece: 930 kg - maximum dimensions of the workpiece (length x width x height): 3050 x 1525 x 25 mm - laser type: CO2

Condition: not inspected (used), functionality: unexamined, overall weight: 200 kg, total length: 600 mm, total width: 500 mm, total height: 1,600 mm, table diameter: 40 mm, No minimum price – guaranteed sale to the highest bidder! The machine is being auctioned as part of a business closure. Placing a bid obligates you to collect the machine on time between 26.01.2026 and 29.01.2026! TECHNICAL DETAILS Diameter of support surface: 40 mm MACHINE DETAILS Dimensions & Weight Fpsdpfsxqnv Esx Afnob Dimensions (L x W x H): 600 x 500 x 1,600 mm Weight: 200 kg

Condition: excellent (used), Year of construction: 2009, operating hours: 999 h, functionality: fully functional, machine/vehicle number: 0121, Used CNC gear rolling machine Manufacturer: PROFIROLL Fedpfex Tb R Dox Afnepb Model: ROLLEX HP Year of manufacture: 2009

Condition: excellent (used), Professional, mechanical analog hardness tester for measuring the hardness of metals according to the following scales: Brinell / Rockwell B / Rockwell C / Vickers The device operates without power – ideal for fast measurements in the field, during production, or for quality control. Features: • Original set with carrying case, manual, and accessories • BRINELL, ROCKWELL B and C, and VICKERS scales • Model: No. 3 / Instrumatic Universal Härteprüfgerät • Manufacturer: C.V. Instruments Ltd, Bradford, England • Mechanical dial indicator – measurement without power supply • Clear analog measurement scale ⸻ Set includes: • Hardness tester • Carrying case • User manual in German • Set of adapters and bushings (visible in the set) Fodpfx Afsvbwzienopb Condition: Like new / warehouse stored Equipment unused or tested only a few times – no signs of wear.

Condition: used, Year of construction: 2004, workpiece diameter 125 mm module 4 control SIEMENS SINUMERIK travel -x axis 105 mm Fpjdsx Szm Aspfx Afneb travel -y axis 40 mm travel -z axis 500 mm workpiece diameter 17 - 39,5 mm workpiece height 6 - 15 mm Gear Honing Machine | GLEASON-HURTH - ZH 125 The machine is in very good condition. Please note that the technical details were added from comparable machines. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: ZH125 | ZH-125

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, table bore: 80 mm, table diameter: 145 mm, gear diameter: 125 mm, controller manufacturer: Siemens, controller model: SINUMERIK 840 D, TECHNICAL DETAILS Working Area Maximum wheel diameter: 125 mm Maximum module: 3 Maximum gear width (spur gears): 24 mm Centre distance: -25 to +180 mm Maximum swivel angle: 12° Maximum helix angle: 45° Table Table diameter: 145 mm Table bore: 80 mm Infinitely variable table speeds: 0.03 – 50 rpm Shaper Spindle Strokes (double strokes): 1,500 – 3,000 DS/min Stroke position adjustment: 70 mm Stroke length min./max.: 0 – 30 mm Shaper spindle diameter: 85 mm Cutter holder interface: HSK 80 B Tool and Workpiece Tool number of teeth: 1 – 200 Minimum tool module: 0.05 Workpiece number of teeth: 1 – 1,500 Minimum workpiece module: 0.05 Control Control system: SINUMERIK 840 D MACHINE DETAILS Electrical Data Drive power: 7.5 kW Total connected load: 30 kVA Fedpowyn Amjfx Afnspb Weight and Dimensions Machine weight: approx. 8 t Space requirement: approx. 4.3 × 2.8 × 2.9 m EQUIPMENT Swiveling counter holder with 4 positions Automatic workpiece changer Linear workpiece conveyor

Condition: excellent (used), Year of construction: 1998, operating hours: 50,000 h, functionality: fully functional, Technical Data – Gear Grinding Machine Reishauer RZ 362A Machine type Gear Grinding Machine Manufacturer Reishauer AG, Wallisellen, Switzerland Model RZ 362A Year of manufacture 1998 Machine number 73889 Commission number 309 CE compliant Yes Electrical data Mains connection 3 x 400 V, 50 Hz Machine voltage 3 x 400 V, 50 Hz Control voltage 1 x 230 V, 50 Hz / 1 x 24 V DC Contactor voltage 1 x 24 V DC Valve voltage 1 x 24 V DC Electrical diagrams standard Grinding wheel dimensions Minimum / maximum outside diameter 280 / 350 mm Maximum width with limitations 84 / 104 mm Number of starts with limitations up to 3 Maximum usable width (with shifting motion) 90 mm For module > 7 or more than 3 starts, Reishauer guidelines apply Grinding wheel speeds During grinding 1,100 – 2,300 rpm During profiling 50 – 95 rpm During setup (special mode) max. 200 rpm Grinding infeed In grinding mode per grinding stroke 0.01 – 1.0 mm Total infeed (fx tot) 9.99 mm In setup mode (special mode) max. 2 m/min Grinding stroke Maximum grinding stroke 175 mm Automatic grinding wheel return stroke for workpiece change 65 mm Shifting movement Maximum shifting travel continuous shifting per 1 mm grinding stroke 0 – 1.0 mm Workpiece data Minimum workpiece pitch diameter depending on grinding wheel diameter Grinding wheel Ø 280 mm: 50 mm Grinding wheel Ø 320 mm: 10 mm Grinding wheel Ø 350 mm: 10 mm Automatic centering with sensor (RZ 362A only): 20 mm Maximum workpiece outside diameter 360 mm With “Felsomat” loader (optional, RZ 362A only): 300 mm With automatic centering using sensor (RZ 362A only): 320 mm Minimum distance from grinding wheel center to workpiece center 165 mm Maximum face width 175 mm For pitch diameters < approx. 150 mm, face width is reduced due to clamping chuck and tailstock design Maximum workpiece weight 60 kg With “Felsomat” loader (optional, RZ 362A only): 4 kg Center distance Fixed manual tailstock (optional): 645 mm Special manual tailstock (optional): 745 mm Hydraulic tailstock (optional, RZ 362A only): 515 mm (645 mm with reduced grinding stroke) Gear data Number of teeth minimum 6, maximum 600 Module without automatic centering minimum module 0.5 (DP 48) Module with automatic centering minimum module 0.8 (DP 32) Maximum module 7.0 (DP 3.5) Helix angle Minimum 10° Maximum 40° Maximum inclination angle left and right 45° Shifting limitations apply for large helix angles, especially above 30° Crowning and profile modification Fedpfex Sxbdox Afnopb Tip relief and crowning height Crowning length and taper Maximum modification depends on profiling tool and process data Weights (without oil filling) Machine weight approx. 5,000 kg Electrical cabinet approx. 1,100 kg Hydraulic unit approx. 600 kg Grinding oil unit RTO 100 (optional) approx. 1,600 kg Grinding oil unit RTM 100 with magnetic pre-filter (optional) approx. 1,650 kg Grinding oil unit RTA 150 (optional) approx. 2,500 kg “Felsomat” gantry loader (optional, RZ 362A only) approx. 1,600 kg Loading unit approx. 1,000 kg Workpiece storage approx. 400 kg

Condition: used, Year of construction: 1986, max. wheel diameter 150 mm max. module 5 min. module 0,5 Fpodpexzuziefx Afnob weight of the machine ca. 10.000 t dimensions of the machine ca. 6500 × 2700× 3600 m

Condition: used, Portable hardness tester IMPACT with integrated impact device Type: TH-130 Hardness testing methods: Rockwell, Vickers, Brinell, Shore Minimum specimen thickness: 3mm with support Battery operation up to 8 hours Printer connection - usable in all positions, including overhead - precise and reliable hardness measurement according to ASTM A956 - Dynamic, fast hardness testing method with direct hardness value display on the screen - Charger - Operating instructions Fjdpexciwujfx Afnjpb The handheld device displays hardness values in all common scales such as HRC, HRB, HV, HB, and HS.

Condition: good (used), Year of construction: 2009, functionality: fully functional, Technical details max. wheel diameter 2-45 mm gear width 250 mm max. module 1,5 mm min. module 0,5 mm Control Fanuc 18i-MB weight of the machine ca. 2,2 t dimensions of the machine ca. 2100 x 1440 x 1700 m Additional information The combined CNC gear hobbing and worm milling machine KOEPFER MZ 120 is characterized by its flexible usability and is used in the small module area. Just by swiveling the milling spindle from the horizontal to the vertical position and selecting the corresponding operating mode of the CNC control, the worm milling machine becomes a gear hobbing machine and vice versa. CNC control Fanuc 18i-MB (Dialog/ISO) CNC axes = X-axis plunge axis Z-axis longitudinal axis C-axis workpiece spindle B-axis tool spindle V-axis loader axis longitudinal A-axis swivel axis tool spindle head (included as an option) Y-axis shift axis (included as an option) With the following production programs: Worm milling Hobbing Fedpfxox Sqiyo Afnepb Worm hobbing Bevel gear and spur gear milling Bevel gear hobbing Milling cycles = straight, oblique, crowned toothing, radial, radial-axial, co- and counter-rotating milling, roughing, finishing, worm gears, straight-toothed bevel gears, face gearing (option only in the partial process) Worms [Equipment] Coolant tank 300 liters KF with LNS Turbo MS 250 Chip conveyor, built in 2021!!! Kraft and Bauer fire extinguishing system Spiral conveyor Machine documentation [Technical data] Workpieces: Workpiece diameter 2-45 mm Max. workpiece length 250 mm Tooth length 150 mm Max. module in steel= 1 mm (gear hobbing) 1.5 mm (worm milling) 0.5 mm (bevel gear hobbing) Tools: Cutter diameter= 16-32 mm (gear hobbing) 40-63 mm (worm milling) Machine: Max. setting angle of milling head= +/- 45° (gear hobbing) +/- 30° (worm milling) Shift travel= 34 mm (manual adjustment) 34 mm (CNC axis) Collet/retraction mandrel W 20 Max. speed of workpiece spindle 770 rpm. Milling spindle drive 0.55 kW Max. milling spindle speed 8000 rpm Axis drives = X-axis (plunging) / travel 80 mm via CNC Z-axis (longitudinal feed) / travel 190 mm via CNC C-axis (workpiece axis) via CNC Rapid traverse = X-axis 6000 mm/min. Z-axis 6000 mm/min. Hydraulic unit 0.37 kW

Condition: good (used), Year of construction: 2004, Ref. -No.: 10612 Manufacturer: LIEBHERR Type: LC 3002 Year of construction: 2004 Type of control: CNC Control: LIEBHERR Storage location: Halberstadt Country of origin: Germany Serial no.: 30XX Max. Module: 30 mm Min. Module: 4 mm Max. Workpiece Diameter: 3000 mm ambient temperature: +15...+38 ° cutting speed: 25 - 250 m / min Milling head swivel angle: 0,001 ° Resolution accuracy: 0,1 Degree Workpiece table load: 300 kN Operating voltage: 400 V control voltage: 24 V frequency: 50 Hz Max. rated current: 230 A Fuse in the supply line: 250 A Max. milling diameter spur gears/helical gears: 3.000 mm Further information: Suitable for internal and external gear cutting. The machine can be viewed by appointment. Fodpfx Ajx R R E Ejfnspb

Condition: used, Year of construction: 2007, max. dia. of teeth cutting 2000 mm workpiece dia. 2700 mm Diameter of the table 1500 mm max. module 22 Control 840D turning speeds 3,5 U/min table load capacity 20000 KG Distance of shafts 70...1220 mm Stroke length 30...330 mm no. of strokes 10...200 Hub/min total power requirement 138 kW weight of the machine ca. 38 t dimensions of the machine ca. 11x5 m machine: Full CNC machine with electronic rolling coupling for C- and D-axes and digital INDRAMAT drive technology. Stiff machine bed in welded construction. Radial axis (X-axis) with hardened guideways, sliding guide with wraparound, longitudinal guide with roller recirculating shoes. Ground preloaded ball screw with play-free preloaded nut. Digital AC drive technology with play-free gearbox. Linear measurement system for radial positioning. Freestanding machine table with electrohydraulically play-free preloaded double worm gear, part wheel diameter 1365 mm, hydrostatic axial and radial bearings, automatic compensation of the workpiece weight. Table hole with a diameter of 500 mm through and open at the bottom. Water-cooled digital AC servo motors. The machine is to be installed on a foundation. Machine stand: as a highly rigid cast construction for axial travel of 1200 mm. Axial axis (Z-axis) with hardened guideways, slide-guided, longitudinal guide and wraparound with roller recirculating shoes. Ground ball screw with play-free preloaded nut. Digital AC drive technology. Encoder for axial positioning. Shapping head: SK 4.1 with hydraulic NC servo drive for impact spindle movement and cutting wheel lifting, stroke length 330 mm, impact spindle diameter 160 mm. Hydrostatically supported impact spindle, linear guide and lateral guide for the lifting mechanism. Maximum tool diameter 300 mm. Fpsdpfx Asx R U Hmofnjb Drive motor power 30 kW. Stroke rates from 10 - 200 DH/min, stroke speed from 5 - 45 m/min. Impact spindle speed for working and return stroke independently programmable. In the cutting area, the spindle speed remains constant. Maximum cutting wheel speed 10 rpm, digital AC drive technology. Cutting wheel lifting correction for internal and external gearing manually reversible. Lateral offset of the impact spindle axis up to 50 mm from the machine center to prevent return stroke collision of the cutting wheel, manually adjustable.

Condition: used, Year of construction: 1989, max. wheel diameter 150 mm max. module 5 min. module 0,5 Fpjdpewhq Egsfx Afneb weight of the machine ca. 10.000 kg dimensions of the machine ca. 6500x 2700x 3600 m

Condition: good (used), Year of construction: 2000, Ref. -No.: 10609 Manufacturer: GLEASON - PFAUTER Type: P 2400 G Year of construction: 2000 Type of control: CNC Fpodpfx Ajx R R Exjfnjb Control: Siemens 840 D Storage location: Halberstadt Country of origin: Germany Machine length: 1100 mm Machine width: 6585 mm Machine Height: 5200 mm Max. Workpiece Diameter: 2640 mm Weight Of The Machine Ca.: 23 t Grinding Wheel Diameter: 400 mm Spindle Speeds (Infinitely Variable): 600 bis 6000 mm Grinding Wheel Width: 80 mm X-Axis: 1200 mm Y-Axis: 300 mm Z-Axis: 1000 mm Z2 - axis: 150 mm Sandable profile depth: 80 mm Workpiece table: 0 bis 5 1 / min Feed rate X-axis: 3000 mm Feed rate Y-axis: 5000 mm Z-axis feed rate: 6000 mm Further information: - Fully automatic centering device - Oil mist separation - Gear tooth measurement - “Profile grinding” software package - Error diagnosis - IFK2 internal milling head - Milling mandrel with spacer discs - Chip conveyor - Oil mist extraction - Technical documentation

Condition: used, Year of construction: 2013, max. wheel diameter 260 mm gear width 320 mm max. module 4,5 min. module 0,5 Control SIN 840D ical angle +/- 45 ° total power requirement 68 kW weight of the machine ca. 15500 Kg dimensions of the machine ca. 3,25 x 3,25 x 3,30 m Fire extinguishing system Siemens Sinorix TM Knoll Filtering system VL1500/8000 year 2017 Wekal loading cell Fedpfx Aex R U Hgjfnspb

Condition: used, Year of construction: 1987, max. wheel diameter 150 mm Fodpowhq Afofx Afnjpb gear width . mm max. module 5 min. module 0,5 Control . total power requirement . kW weight of the machine ca. 10.000 t dimensions of the machine ca. 6500 × 2700× 3600 m

Condition: used, Year of construction: 2012, max. wheel diameter 300 mm gear width 320 mm max. module 10 min. module 0,5 ical angle 45 ° frequency 50 Hz voltage 400 V main fuse 125 A x-axis 270 mm y-axis 250 mm z-axis 320 mm A - axis +/- 45 ° B - axis 360 ° C-axis 360 ° total power requirement 89 kW weight of the machine ca. 23,5 t dimensions of the machine ca. 11,2 x 5,5 x 2,9 m automated Oil slinger station Fjdpex R U Haefx Afnopb EWAB workpiece storage Hoffmann coolant filter system HSF 100 SE/K Minimax fire extinguishing system W+W air filter system Promot Automation "Cellmaster" (3 cells) year 2019

Condition: used, Year of construction: 1998, max. wheel diameter 85 mm Fpsdpfswhqx Tox Afnsb gear width max. 125 mm max. module 3 Control ja total power requirement 30 kW weight of the machine ca. 8 t

Condition: used, Year of construction: 2003, max. wheel diameter 275 mm gear width 58 mm max. module 13 min. module 2 Control SINUMERIK 840 D number of teeth 5 - 200 ratio of transmission 10:1 cutter diameter max. 228 mm x-axis 25 - 350 mm y-axis +/- 175 mm z-axis 125 - 600 mm b-axis -5 / +90 ° total power requirement 75 kW weight of the machine ca. 11,7 t Fpedpfjx R U E Njx Afnjb dimensions of the machine ca. 12,5 x 3,0 x 3,0 m Equipped for dry milling Pressure deburrer Deburring device with driven brush Integrated magnetic chip conveyor Promot Cellmaster Cartridge pulse filter system User interface control works with Gleason Summary

Condition: used, Year of construction: 2005, weight of the machine ca. 7.800 kg dimensions of the machine ca. 3.380 x 3950 x 3015 m Fpsdpoudc S Hjfx Afnsb