Used Crash Barriers for sale (871)

Condition: new, machine/vehicle number: 8e6cf81e11b107f23f22f209a, axle configuration: 3 axles, tire size: 435/50 r19.5, Further information Fine-grained steel welded construction, with preload slight pretension in the neck area, saddle plate with replaceable 2 , kingpin, outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment, 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm, pull-out ladder at the rear, lateral door stop, 2 wheel chocks with holder, aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of 1st axle and behind each axle, with anti-spray flaps according to EC, impact protection at the rear SAF disc brake axles, laser-measured axle/chassis to reduce tire wear and fuel consumption, air suspension 2-line compressed air brake system, colored cable routing for easy servicing, spring-loaded parking brake, 2 swap-proof coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS, with lift & lower valve, vehicle stability system 435/50 R19.5 tires of the manufacturer's choice, steel rims, factory silver 24 volt, multi-chamber lights, amber LED lighting at the sides, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable Podpfxoi Ri E Ho Aalopl Floor: Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front bulkhead / corner stanchions: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and a long pocket at the bottom, 3 pairs of stanchion positions Insertion slats: 5 rows of wooden insertion slats Rear wall / rear corner stanchions: Rear steel corner stanchions up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin: Tarpaulin with welded-in horizontal and vertical straps, stainless steel tensioning fasteners Roof: Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for car industry, internal width between the roof rails, approx. 2 490 mm, tarpaulin color: white, 400 Roof non-elastic, hardly any deflection of the roof rail when loading and unloading, optimum rain strip at the rear, at the top of the end bows, above the doors, EcoLift - lifting roof can be raised by approx. 380 mm, with gas pressure damper support, 3 driving positions at the front: interior height at the front approx. 2900 mm/ 2950 mm / 3000 mm, adjusted to approx. 3000 mm Germany, test approval according to EC 2007/46, 24/7 service hotline, Fliegl manufacturer's certificate for structural strength according to EN 12642 XL, prepared for single-line license plate holder, warning sign according to ECE - 70, reflective strips: white, continuous on the side tarpaulin at the bottom and at the top in the corners (if visible drop sides, then the strip at the bottom, on

Condition: new, machine/vehicle number: 068983c41e44eb5660fa9100c, empty load weight: 6 kg, maximum load weight: 28 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 435/50 r19,5, Further information Chassis saddle forwarding Fine-grained steel welded construction, with preload slight pre-tensioning in the neck area, saddle plate with replaceable 2 kingpins X-tra Long, with 15030 mm internal length Outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm Extension ladder at the rear Door retainer at the side 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Quarter-shell mudguards in front of 1st axle and behind each axle Impact protection at the rear Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system AAC Basic, automatic relief axle acting on last axle, as maneuvering aid, up to 20 km/h, can be switched off manually Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 435/50 R19.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side Side amber LED lighting coupled with the blinker Flashing side lights Side lights 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Floor Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front wall / front corner stanchions 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions 3 pairs of sliding stanchions can be moved along the entire length, with 4-fold pockets and with long pocket at the bottom. 3 pairs of stanchion positions Insertion slats 5 rows of wooden slats Rear wall / rear corner stanchions Psdpfx Aaoi Riwuelepl Rear corner stanchions steel up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Stainless steel tension locks Roof Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white Roof non-elastic, hardly any deflection of the roof rail when loading and unloading EcoLift - lifting roof can be raised by approx. 380 mm, on both sides, with gas pressure damper support, 3 driving positions at the front: Front interior height approx. 2900 mm / 2950 mm / 3000 mm, adjusted to approx. 3000 mm Optimum rain strip at the rear, at the top of the end bows,

Condition: used, machine/vehicle number: YV2ASW0C88A65xxxx, mileage: 652,000 km, Year of construction: 2008, Please contact ATS Norway for more information Please provide reference number upon request: 20301 Specifications: Km: Approx. 652,000 Transmission: Automatic Air suspension Engine brake JOAB on construction 20T hook Trailer hitch VBG Euro 4 Tires (see pictures) Hydraulic underrun barrier Grill Ppedpfx Aswi R D Eealel Extra light Rotor beam 2 years Radio/CD Air conditioning/AC Maintenance done by owner Ready for delivery Description:Volvo FH480 Hook truck from 2008.Ready for delivery.Sold without box. Km: 652000 HK: 480 Technical approved: Yes EU-approved until: 24.03.2026 Own weight: 12960 Total Weight: 27000 Payload: 13965 Width: 255 Length: 880 Euro: 4 Model: FH480 Krokbil Gearbox: Automatic

Condition: used, machine/vehicle number: YV2RT60G3JA83xxxx, mileage: 136,000 km, Year of construction: 2019, Please contact ATS Norway for more information Please provide reference number upon request: 19582 Truck specifications: - Km: Approx. 136,000 - Transmission: Automatic - Suspension: Steel - Air - 10 ton front axle - Retarder - Euro 6 - Okay tires Podex Izrkepfx Aaljpl - Extraction - Length of plane: Approx. 6.5 m - 8x4 - Trailer hitch - VBG - Hydraulic underrun barrier - 551 HP - Turn on 4 - Support legs - Tool cabinet - Bed - Radio/CD - Air conditioning/AC - Silver agreement with Volvo since new (still going on) Crane specifications: - 2018 HMF 5020K - Hour meter PTO: Approx. 3320 - Support legs - Approved until 10.2026 - FJ-1000 Jib - Crane diagram - 6 5 hydraulic extensions - Videos Description: Well-maintained Volvo FH540 Tridem crane truck from 2019. The truck is equipped with a 50 t/m HMF crane with Jib. Only 136,000 km and 3320 PTO hours. It has been under a lease agreement since new and is still going strong. Ready for delivery. Km: 136000 HK: 550 Technical approved: Yes EU-approved until: 12.04.2026 Own weight: 20870 Total Weight: 37000 Year controlled until: 10.25 Payload: 16055 Width: 255 Length: 1046,3 Euro: 6 Model: 2019 Volvo FH540 8x4 Tridem Kranbil m/ 50 t/m HMF kran m/ Jibb. Lite km og krantimer! Gearbox: Automatic

Condition: used, _____ Description: Year of manuf. : 2020 Control : Sonstige WEISS CNC Centre width : 6 mm In Generel: ear of construction:2020 Control system:WEISS CNC Centre width:6 mm Centre height:200 mm Grinding wheel dimensions:400x60 mm + 0x60 mm Workpiece headstock: Speed:1 rpm Workpiece weight max.:25 kg Sanding diameter max.:390 mm Mounting:MK4 Grinding headstock: Peripheral speed:2 m/s Grinding disc dimensions right:0 x 60 mm Grinding disc dimensions left:400 x 60 mm X-axis:380 mm Z-axis:1,1 mm B-axis:torque motor, infinitely variable Tailstock: Pinole diameter: mm Pionole stroke:45 mm Mounting:MK 4 Cylinder fine adjustment:+/- 0.04 mm Podpfxov Armco Aalspl Equipment: Positioning sensors:Direct scales Grinding spindles:2x grinding spindle (left/right) GAP / Crash Controll:Structure-borne sound (Sensotronik) Balancing:MPM balancing device Workpiece measurement:Marposs PF ME Automation:Robot interface prepared Set-up mode:Electronic handwheel Emulsion mist separator:Mechanical Dresser:For external grinding wheel left/right Accessories:Various grinding discs + flanges

Condition: used, Year of construction: 2020, controller model: , _____ Description: Ppjdpfx Ajxw A Icjalol Year of manuf. : 2020 Technical specifications Working surface:2000 mm x 15000 mm Total width:5070 mm Height:1980 mm equipment :-Global Control S with 15" colour touchscreen :-Joystick and handwheel for Global Control S panel :-Cooling for the control cabinet :-Laser diode :-Drives up to a maximum of 35 m/min. AC :-Heat shield without air cooling :-Runway for double-sided longitudinal drive HEB :-OmniFlow oxyfuel supply up to 70 m'/h (gas flow control) :-ALFA machine cutting torch (internal ignition) :-Smartlifter 300 :-SensoMat ARKI :-Full addressing of gases :-Light barriers :-Safety device for wheel housing (foot switch)

Condition: used, Year of construction: 2020, controller manufacturer: Sonstige, controller model: Global ControlS, _____ Description: Year of manuf. : 2020 technical data Working area:3000 mm x 6000 mm Total width:5070 mm Height:1980 mm equipment Ppsdjxv Nk Uspfx Aalel :-Global Control S with 15" colour touchscreen :-Joystick and handwheel for Global Control S panel :-Cooling for the control cabinet :-Laser diode :-Drives up to a maximum of 35 m/min. AC :-Heat shield without air cooling :-Runway for double-sided longitudinal drive HEB :-OmniFlow oxyfuel supply up to 70 m3/h (gas flow control) :-ALFA machine cutting torch (internal ignition) :-SmartLifter 200 :-SensoMat ARKI :-Full gas addressing :-Light barriers :-Wheel housing safety device (foot switch)

Condition: like new (used), functionality: fully functional, Year of construction: 2023, degree of automation: automatic, laser hours: 2,800 h, laser power: 6,000 W, positioning speed: 280 m/min, Equipment: CE marking, centralized greasing system, cooling unit, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, TruLaser 5030 fiber L76 6kW + LiftMaster Linear + Material Buffer small storage system BASIC MACHINE: TruLaser 5030 fiber (L76) Machine • Working area: 3000 × 1500 mm • Box-type frame • Longitudinal conveyor belt • Precision motion unit for high-accuracy processing • Gantry drive with linear direct drives • Process chiller for machine and laser (water/air) • Work area lighting • Pilot laser • Spraying system • Automatic nozzle cleaning • Integrated electrical enclosures • Integrated cabinet • Enclosed beam guidance via fiber optic cable (LLK) • Machine status indicator light • Transport and installation device TRUMPF laser • Pump diode excitation • Laser power regulation Cutting unit • Universal cutting head with fully adaptive lens system • Protective glass • Online condition monitoring for protective glass • Dynamic Focus Control • Automatic nozzle centering Control • Rapid post-production • SINUMERIK CNC • Ergonomic control panel with 21.5" wide-format multi-touch color display • Integrated technological parameters • Automatic shutdown • Programmable pressure/cutting gas selection • Microweld • Remote maintenance interface • Production planning • Multi-sheet processing • Condition Guide • Cutting Guide Functions • AdjustLine • BrightLine fiber • Smart Nozzle Automation • DetectLine • Drop&Cut • Integrated camera 1 for process monitoring • ControlLine • FastLine • FlyLine • FocusLine • NitroLine • PierceLine • PlasmaLine • Fusion Cut Performance Package • Highspeed Cutting Package • Copper Cutting Package • Brass Cutting Package Data transmission • USB port • RJ45 network interface • Online Update Manager Safety • CE marking and EC Machinery Directive compliant • Light barriers • Multi-chamber compact dust extraction unit • Electric rolling roof • Enclosed protective housing with certified viewing panels on both right and left sides Advanced standard configuration • Compact dust extraction • Mild steel slats • Laser powered via the machine • Automatic longitudinal pallet changer • Machine ambient temperature range 5-35°C / up to 45°C • Smart View MT ready • Data usage agreement • Nanojoints • Smart Rerun / Purchase • External solid-state laser TruDisk 6001 with BrightLine fiber OPTIONS: Highspeed Eco cutting package • High-speed cutting with reduced gas consumption Thick plate cutting package Ppodpoyah Rcofx Aalsl Prefilter for nitrogen and oxygen • Particle filtration for nitrogen/oxygen process gas lines, prefilter with external filter element Easy Filter • For annual maintenance of spent cooling water • Eliminates regular water changes Wireless Operating Point

Condition: new, * IMMEDIATELY AVAILABLE * Including Electric Winch / Removable Container / For Drums up to d=280 cm and b=165 cm TECHNICAL DATA • Brand: Blyss • Model: KTT 35 V2L • Vehicle type: Cable Drum Trailer • Vehicle condition: New • First registration: Without first registration • TÜV/MOT: 2 years from first registration • Internal dimensions (LxWxH): 280 x 165 x 280 cm • External dimensions (LxWxH): 489 x 254 x 214 cm • Loading height (floor): 0 cm • Perm. gross weight: 3,500 kg • Unladen weight: 675 kg • Payload: 2,825 kg • Chassis: Low loader (wheels beside the superstructure) • Tyres: 185R14C • Suspension: KNOTT rubber spring axle • Jockey wheel: Yes • 100 km/h type approval: Optional, retrofittable DESCRIPTION • Designed for cable drums up to a diameter of 2,800 mm and a width of 1,650 mm • With 2m³ container for cable drum trailer • Standard pipe mount approx. 60 mm • 2x plastic adapters for pipes with 80 mm mount • Torsion-resistant chassis with heavy-duty mounting frame, hot-dip galvanized in immersion bath • Easy operation of the mounting frame with or without cable drum • Barrier-free loading of the cable drum and container mounting • Play-free bearing and secure fixing of the drum • Electric winch for loading cable drums • Battery installed in box • Heavy-duty jockey wheel mount and rear support • Stable telescopic crank stands at rear • Very robust welded steel frame • Frame completely hot-dip galvanized • Steel mudguards • Reverse automatic system • KNOTT overrun device and parking brake • 13-pin plug • Reversing lights • Large-dimension safety lighting • Integrated rear fog light • Rear frame with recessed LED lighting • Automatic jockey wheel • ____ • Container data: • Width bottom 116 cm, • Width top 133 cm, • Length bottom 87 cm, • Length top 182 cm • Height of container 100 cm Ppjdpfoyachpjx Aalsl • Container weight: approx. 260 kg • Trough colour: blue RAL 5002 • Pivoting tailgate, suitable for driving over and removable • Tailgate can also be used as a drive-on ramp, e.g. for wheelbarrows • Additional net hooks for tarpaulin or nets ensure optimal load securing • Container capacity approx. 2 m³ New vehicle with warranty and TÜV. ————— - Financing or leasing available - Nationwide delivery available - All prices incl. VAT - Vehicle registration documents can be sent in advance or temporary licence plates (Germany) can be provided - Export plates including customs clearance possible Descriptions and images are copyright protected! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available for you! We have been specialist dealers and service workshops for over 30 years for Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - Errors, omissions and prior sale excepted -

Condition: new, * IMMEDIATELY AVAILABLE * including hand winch – suitable for drums up to d=280cm and b=160cm TECHNICAL DATA • Brand: Blyss • Model: KTT 27 • Vehicle type: Cable drum trailer • Vehicle condition: New vehicle • First registration: without first registration • TÜV / General inspection: 2 years from first registration • Internal dimensions (LxWxH): 280 x 160 x 0 cm • External dimensions (LxWxH): 470 x 234 x 218 cm • Loading height of platform: 0 cm • Permissible total weight: 3,500 kg • Unladen weight: 711 kg • Payload: 2,789 kg • Chassis: low-loader (wheels positioned beside the platform) • Tyres: 185R14C • Suspension: KNOTT rubber torsion axle • Jockey wheel: Yes • 100km/h approval: Optional, can be retrofitted DESCRIPTION • Designed for cable drums up to a diameter of 2,800 mm and a width of 1,600 mm • Standard pipe receptacle • Torsion-resistant chassis with robust mounting frame, fully hot-dip galvanized • Easy handling of the mounting frame with or without cable drum • Barrier-free insertion of the cable drum • Play-free bearing and secure fixing of the drum • Heavy-duty jockey wheel mounting and rear support • Sturdy telescopic crank supports, rear and front • Includes robust, maintenance-free manual hand winch • Highly stable welded steel frame • Complete frame hot-dip galvanized • Plastic mudguards • Automatic reversing system • KNOTT overrun hitch and parking brake • 13-pin plug • Reversing light • Large dimensioned safety lighting • Integrated rear fog lamp • LED lighting fitted flush in rear frame • Number plate bracket 340x200mm New vehicle with warranty and TÜV (inspection). ————— Ppodeyachispfx Aalel - Financing or leasing available - Nationwide delivery possible - All prices include VAT - Vehicle registration document can be shipped in advance, or we can provide temporary (German) registration plates. - Export plates with customs declaration available Descriptions and images are protected by copyright!! Trailer Center BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available from stock! We have been a specialist dealer and workshop for over 30 years representing Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many other brands. - Subject to errors, changes and prior sale -

Condition: excellent (used), Year of construction: 2016, Professional automatic packaging system from a renowned European manufacturer. Suitable, for example, for packing food products, technical goods, print and paper products, household items and toys, as well as textiles. The machine can be used in various industries such as beverages, food, chemicals, wine & spirits, cosmetics, detergents, wood, textiles, and graphics. It is capable of packaging diverse products including glass and PET bottles, cans, cartons, trays, jars, and boxes of various sizes. The shrink wrap machine is equipped with multiple monitoring sensors, light barriers, and photocells for automatic process control. User-friendly LCD control panel with extensive functions and setting options, such as automatic and setup modes, 20 memory slots for different packaging formats, piece counter, packaging performance calculation, and communication functions. Technical data: - Maximum product dimensions: width up to 760 mm x height up to 380 mm - Suitable for LD-PE film from approx. 20 to 100µm thickness - Maximum film roll width: 750 mm flat film - Packaging performance up to 10 units per minute - Working height approx. 940 to 1100 mm - Motorized unwinding of bottom and top film Psdpfx Aexxzzksalepl - Transport rods made of heat-resistant fiberglass - Frequency-controlled shrink tunnel belt with adjustable speed - Adjustable air flows in the tunnel - Cooling fan at the outlet of the shrink tunnel - Conveying rollers for product centering at the machine's outlet - Low energy consumption - Connected load: 3 x 400 V / 50 Hz / 3 phases - Machine dimensions approx. L 2.6 x W 1.3 x H 2.1 to 2.2 m - Weight approx. 600 kg The machine was in operation for only a few weeks for a specific order. Afterwards, it was taken out of service and placed in storage.

Condition: like new (used), Year of construction: 2018, sheet width 2050 mm plate thickness 3.0 mm distance between columns 2100 mm back stop - adjustable 550 mm no. of strokes 35 Hub/min cutting angle 2°12 table width 400 mm table height 850 mm Control konv. Podpfxox Sr Dxo Aaljpl total power requirement 3.5 kW weight of the machine ca. 1280 kg dimensions of the machine ca. 2400 x 1500 x 1300 mm Current new price approx. 20.000 Euro from a maintenance workshop very little used - mint condition (!!) - in checked conditions - machinevideo - ?v=tUyx7mR0vp4 Equipment: - robust / powerful electro-mechanical guillotine shears - manual material backgauge * stepless adjustment range * adjustment from behind - by handwheel * including mm scale * max. adjustment range 550 mm - Manual kerf adjustment, from the front - 1x side stop - 1x support arms - 1x free-moving foot switch - rear sheet metal chute - rear safety device (light barrier) - Operating instructions (machine control)

Condition: used, empty load weight: 3,080 kg, maximum load weight: 3,320 kg, overall weight: 6,400 kg, axle configuration: 2 axles, first registration: 01/2003, next inspection (TÜV): 03/2026, loading space length: 7,200 mm, loading space width: 2,500 mm, loading space height: 1 mm, suspension: steel, tire size: 205/70R15, color: green, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 2 axles, turntable drawbar, leaf suspension, ABS (anti-lock braking system), underrun protection, storage box Body: 2-axle special low-loader trailer, loading height approx. 500 mm! GFI axles, drum brakes! Psdsx Edqbepfx Aaljpl The trailer was only used by the police for transporting barriers, so it has never been heavily loaded! Spare wheel available at extra cost! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors!

Condition: excellent (used), CNC MASTERWOOD CN10/CN12 PROJECT 500 XL + Programming + Tooling Extra-long XL machine, fully equipped for interior fittings, kitchens, wardrobes, doors, and all standard carpentry work. Working area X = 6,200 mm – Y = 1,660 mm – Z = 150 mm Main motor power: 8 kW – 10-position tool changer – 17 vertical drilling spindles Maximum spindle speed: 24,000 rpm – Tool clamping system: ISO 30 – 4 horizontal drills in X – 2 horizontal drills in Y – Notching saw tiltable to 90° – Gantry frame construction – 10 support consoles – 2 active vacuum pumps + 1 backup vacuum pump – Safety system with guard rails and safety mat Includes 1x chip conveyor – Safety barriers Ppjdsx U Tpnjpfx Aalol The chiller and air dryer integrated in the machine are new – The vacuum pumps were overhauled in 2021 – Ceiling-mounted laser for positioning suction cups and workpieces – The computer system and programming (with internet and USB access) are new and were updated in 2021. Dimensions: 10m x 3.30m x 3m – Approx. weight: 5,000 kg Machine sold complete with programs, control console, tooling, and accessories. In good technical and visual condition.

Condition: good (used), Paper cutting machine Polar 92 EM-MON, air table, light barriers, program control, machine number 5811013, in good condition, available immediately Ppjdpjn Hqdhjfx Aalol

Condition: good (used), Year of construction: 2005, machine/vehicle number: M-078E-018-11/20-05E, Schneider Senator 078E-Line paper cutting machine, serial number: M-078E-018-11/20-05E, built in 2005, with air table, side table, light barriers, and program control, in good condition, available immediately. Psdpfx Aewivimjalspl If you are interested, we would be happy to inform you about other machines in our facility. You are welcome to view the machines in our facility by appointment.

Condition: good (used), machine/vehicle number: 3324-007, Cutting machine Wohlenberg 115 MCS-2 TV, machine number 3324-007, air table, light barriers, program control, monitor, side tables, rear table cover, 1 spare blade, in good condition, available immediately Ppodpfx Astuiz Hsalel If you are interested, we will be happy to inform you about other machines in our company. You are welcome to view the machine at our premises by prior appointment.

Condition: good (used), Year of construction: 1998, machine/vehicle number: 6862012, Polar 78 ED paper cutting machine, built in 1998, serial number 6862012, with program control, air table, and light barriers, in good condition, available immediately. Pjdswaxhajpfx Aalepl If you are interested, we would be happy to inform you about other machines in our facility. You are welcome to view the machine in our facility by appointment.

Condition: as good as new (ex-display), Year of construction: 2025, The brush washbasin LCT bio.x C100 is the proven classic in a new design and with optimized equipment technology. It impresses with its extraordinary stability and load-bearing capacity. The spacious work surface enables barrier-free and comfortable working. - stable construction - particularly low-maintenance - high load capacity - Energy-saving mode for downtimes such as nights or weekends - A flexible articulated hose allows easy rinsing of the parts - Optimum cleaning performance by heating the cleaner to 41 °C The workpieces are rinsed off through a nozzle. With With the help of the flexible articulated hose, the nozzle in the desired position can be fixed. The cleaning brush supports the cleaning strongly Ppodpsh S Undjfx Aaljl dirty parts. The large cleaning surface enables effective cleaning To work. High carrying capacity of the washer due to stable device construction. Device is made of plastic and is therefore very stable and corrosion-free. Easy to transport using a lift truck. Multi-stage filter system, consisting of coarse screen, fine screen and magnet. In addition, a washable filter bag holds (fineness: 100 μm) finest impurities back before they get into the bathroom. A functional control with soft-touch control panel guaranteed by choosing the energy saving mode Energy savings of approx. 50%. All electronic components of the device are in one compact technical unit. Our LCT bio.x C100 can be used with the following label-free cleaners be driven LCT BioLiquid LCT Bio Liquid Special LCT Bio Liquid Power: LCT coconut cleaner LCT Coconut Cleaner Alu LCT Coconut Cleaner low-foaming

Condition: new, Year of construction: 2016, 2-post lift 4.2 t – barrier-free – Professional Line TW 242PEB43 The Professional Line lift is designed for daily professional workshop use. Features include automatic release of the safety locks and two-stage swivel pads. Fully barrier-free drive-through area. The lift is also equipped with an automatic limit switch, which stops lifting as soon as an over-height vehicle reaches the crossbeam. Each outer side of the columns has a practical plug adapter holder, providing secure storage for two plug adapters each. Anti-Lift-Up button enables precise lowering of the lift without prior automatic lifting. Also includes a convenient 230 V socket directly mounted on the control box. * Top-quality workmanship with CE certification * Manufactured according to ISO 9001 * New: Anti-Lift-Up button * New: Practical 230 V socket on control box * Protective covers in front of the columns * Automatic locking and unlocking of safety latches * High-quality support columns made from special rolled profiles * 2 hydraulic cylinders for powerful lifting and lowering * Automatic arm locking mechanism * Synchronous control via wire ropes * Telescopic support arms * Practical plug adapter holders (one per column side) for two plug adapters each ----* CE lifting capacity: 4200 kg * Max. lifting height: 1900 mm / Ad 2080 * Swing-in height: 96 mm * Lifting/lowering time approx.: 45/30 sec. * Drive voltage: 400V / 3 phase * Power: 2.2 kW * Fuse: 16 A (C/slow-blow) * Net weight: 700 kg * Lifting height (swivel pads retracted): 1900 mm * Lifting height (swivel pads extended): 1960 mm * Lifting height (plug adapter + swivel pads extended): 2060 mm * Safety unlocking: automatic * Swivel pads: 2-stage * Powder coated: yes * Anti-Lift-Up button: yes * Total width/base plate (without motor): 3436 mm * Column height: 4300 mm * Required concrete thickness: 200 mm * Support arm length / short (approx.): 740 – 1150 mm Ppedpfx Aekpl Elsalsl * Support arm length / long (approx.): 890 – 1390 mm * Width between columns: 2850 mm * Max. drive-through height: 4135 mm * Max. drive-through width: 2574 mm * Color: RAL 5015 (Blue), RAL 7000 (Grey) ----Stock no. 93 -----Subject to errors & prior sale WhatsApp support available! If you have questions about the unit or require further information, feel free to contact us conveniently via WhatsApp. WhatsApp – German, English -- WhatsApp – German, English, Arabic

Condition: new, maximum load weight: 37,495 kg, overall weight: 41,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Selection of equipment. Full equipment details available on request. Chassis * Double-T longitudinal member chassis with welded cross-members * Front frame height: approx. 147 mm (including fifth wheel plate) * 'Compact-Rear' chassis design * Replaceable 2 kingpins, 1 position: front overhang approx. 570 mm * Container rails made of rectangular tube, approx. 200 x 120 x 8 mm * Reinforcements at the apron slope * Fixed rear crash bar in steel design * Rear underrun protection in accordance with EC Directive * Side underrun protection in accordance with EC Directive * Side underrun protection approx. 460 mm high * Quick-Lock full equipment – locks at every possible position – locks are theft-proof * Container locks for the following container: 1 x 20' container, flush-mounted at rear * Distance kingpin to rear edge of vehicle: approx. 6,620 mm Support device * Two mechanical support landing gears, 2 x 12 t, semi-circular with base plate, manufacturer: Jost * Landing gear operation on one side, on FR-right Axles/Aggregate * 3 axles each with 9,000 kg load capacity * Wheelbase: approx. 1,410 / 1,310 mm * KRONE axles with air suspension and disc brakes * ET 120 * Aggregate spacing = approx. 4,625 mm * Brake disc diameter: approx. 430 mm Pjdpfx Aaewx Ddqelopl * Fully automatic, load-dependent electronic lift axle control for 1st axle * Manual function at the control panel for forced lifting (as starting aid according to Directive 97/27/EC) and forced lowering via rotary switch * Preparation of lift/steer axle(s) for operation from the motor vehicle (without motor vehicle installation), as per selected light connection(s), control via Contact 6 of 7-pin auxiliary plug ISO 3731 and/or Contact 12 of 15-pin plug ISO 12098 and/or Contact 8A of VBG connection * With lifting and lowering device, including automatic height reset for driving position Tires (Rims) * 6x, 385/65 R 22.5 – premium tires per Krone selection * Without spare wheel * KRONE Smart Tyre Monitoring as per ECE R141 for pressure & temperature monitoring * Wheel nuts with KRONE protective caps * TPMS control unit without connect function in TPMS control device Brakes * Brake system according to ECE Regulation 13 (including trailer stability function) * Spring-loaded parking brake * Diagnostics via ISO7638 connection (EBS supply cable) * Brake line connections below the top of the frame * Prepared for KRONE Telematics Dry * Wheel chocks with holder * Standard air connections ISO 1728 (Palm) * Lightweight aluminium air tanks * Brake system: Wabco Premium * Attention: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! * EBS system, 2S/2M, 2 sensors on one axle Lighting * Lighting and signal system according to UN ECE Reg. No. 48 * 2 outline marker lights with rubber arm, LED design * Electrical connections below the top of the frame * LED side marker lamps with direction indicator function (blinker) * 24 Volt, front with 7-pin socket DIN ISO 1185 * 7-pin socket DIN ISO 3731 at front for additional functions * Additionally at front, 15-pin socket DIN ISO 12098 * Two x two 3-chamber rear lights (full LED), round * 2 LED reversing lights * LED rear fog light * 2 LED combination lamps (reverse and rear fog combination) * 2 LED license plate lights Accessories * 1 fire extinguisher, 6 kg, incl.

Condition: used, Year of construction: 2010, functionality: fully functional, Used longitudinal and transverse cutting line Manufacturer: Forstner Year of manufacture: 2010 Performance: 2.00 mm at 400 N/mm² Psdpsxvqzhsfx Aaljpl Equipment: - Motorized 3-ton decoiler with pressing arm - Material lifting table - Control: Siemens PLC - Speed: 25 m/min - Standard feed shaft - Standard feed table automatic straightening unit: - Straightening rollers: Programmable (MOP) - Straightening shafts: Standard Slitting: - Upper shaft adjustment: Motorized (MOV) - Number of slitting knives: 5 pairs Cross cutting: - Guillotine shear Additional equipment: - Light barrier unit - Manual 500 kg decoiler - Recoiling unit . Photos are currently being taken at the customer. The machine can be inspected on site by arrangement (Stuttgart area). Dismantling will take place around February 2026. No guarantees or warranties on used machines.

Condition: like new (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: vec1206-L-1809RO1, input voltage: 400 V, total length: 7,000 mm, total width: 7,000 mm, total height: 2,000 mm, compressed air connection: 6 bar, type of input current: three-phase, year of last overhaul: 2024, overall weight: 2,000 kg, input current: 11 A, mount diameter: 7,000 mm, loading space length: 7,000 mm, loading space width: 3,000 mm, loading space height: 2,000 mm, Laminated steel frame. safety bars for each print head Pjdpfx Aevccqxjalepl and loading/unloading station. - Safety barrier to prevent operators from entering the stations during work -FOOT PEDAL (print order) -SERVOINDEXATOR-Precise pallet position control +/- .001". Ensures smooth indexing with superior print consistency -Increase production with precise control of acceleration and deceleration direction index: right and left -Programmed with Step-Back, Multi Step-Back and Cycle indexing options -Adjustment of the carousel stroke in both directions -15" TOUCHSCREEN with Aries 2 operating system Easy operator access to all machine parameters Program multiple heads simultaneously Full speed control in both directions of travel View number of prints in real time, speed (pcs/hour) Save all parameters of a stored job: indexer speed, head speed of printing, printing area, number of strokes, time and temperature flash polymerization, color design Setting the preheating temperature of the pallets Quick setting at the same print speed and distance for all heads -Electrically operated PRINT HEADS-10 stations, 6 colors, 4 intermediate flashes, 12 pallets -VERY USEFUL for printing with water-based ink (automatic screen flooding system with ink after printing) - adjusting the screens (templates) with maximum precision in 3 points (front-back, left-right, rotational movement) -adjusting the distance between the pallet and the screen giving you the flexibility to print practically any ink on any substrate at the touch of a button - independent adjustment of the angle of the scraper and counter-scraper, with possible adjustments do with one hand - INTERMEDIATE FLASHS - RAPID WAVE QUARTZ QUARTZ FLASH 51cmX53cm (12 lamps) maximum coverage area Each of them is divided into 3 separate areas (front, middle, back) that can be used depending of the print size: area one, area two, area three, each two/all three CONFIGURED FOR THE POSSIBILITY OF INTERMEDIATE DRYING AFTER EACH PRINT: PRINT/FLASH/PRINT/PRINT/FLASH/PRINT/FLASH/PRINT/FLASH/PRINT/FLA SH/PRINT (POLYCROMY AC-powered printheads enhance finesse, speed and power Front and rear travel adjustment One-handed tool-free squeegee/flood bar lock for quick and easy charging and changing 15" touch screen with Aries 2 operating system Easy operator access to all machine parameters Program multiple heads simultaneously Full speed control in both directions of travel View real-time number of prints (dozen) and speed (pcs/hour) Save all parameters of a stored job: non-contact, indexer speed, indexer speed, printhead speed, print area, number of strokes, flash curing time and temperature, color design, mode Set the pallet preheat temperature Quickly set the same print speed and distance for all heads Print heads AC electric print heads for a stronger and smoother stroke Press the button at the loading/unloading stations to prevent printing on empty pallets Adjustable side supports for low-profile screens for easy access True three-point micro-registration (front to back, left to right and roll motion)

Condition: new, with compressed air cleaning and frequency inverter Start-up with frequency inverter Pressure transmitter for demand-based control Pre-separator integrated Extinguishing system integrated Efficient and economical: Large-volume compressed air tank with fast-acting diaphragm valves for effective OPTI JET filter cleaning and minimal compressed air consumption. Simple yet effective: OPTI JET cleaning and bag filters with snap ring closure. Extremely efficient: Energy-efficient IE3-class drives. Safe in case of emergency: Service-friendly extinguishing system. Pjdpjwzyh Rjfx Aalepl Exceptionally quiet: sound-insulated air recirculation from AL-KO. All options available: PLC control for manual and automatic operation. Countless options, such as machine recognition, damper control, and frequency-controlled operation, to name just a few. No mess: Collection container with inspection viewing window. Practical down to the last detail: Container locking with ergonomically shaped clamping lever. Easy retrofitting: Can be converted for discharge via briquette press or rotary valve. - high extraction capacity - minimal space requirement - 100% air recirculation without temperature loss - (residual dust < 0.1 mg/m³) - integrated pre-separator and expandable control system - optimal filter cleaning - minimal noise level - optional: patented fill level monitoring - service-friendly, certified fire extinguishing system - dust barrier for dust-free container change - (optional: safety interlock for containers) - modules freely configurable and expandable ----- Technical Data ----- Extraction nozzle Ø: 355 mm Nominal air flow: 7,127 m³/h Max. air flow: 10,000 m³/h Max. negative pressure: 3,347 Pa Filter area: 73 m² Chip collection volume: 3 x 250 liters Number of bags: 3 pcs Motor 400 V: 15.0 kW Dimensions (LxWxH): 3,320 x 1,058 x 2,361 mm Sound pressure level: 73 dB(A) Weight: 1,064 kg according to: GS - HO - 07

Condition: new, with compressed air cleaning and frequency converter Startup with frequency converter, Pressure transmitter for demand-based control Podjxpximepfx Aalepl Pre-separator integrated, Automatic fire extinguishing system integrated Efficient and economical: Large-capacity compressed air tank with fast-acting diaphragm valves for effective OPTI JET filter cleaning and minimal compressed air consumption. So simple and so effective: OPTI JET cleaning and filter bags with snap ring closure. Exceptionally economical: energy-efficient drives according to IE3 Safe in case of emergency: maintenance-friendly fire extinguishing system. Extremely quiet operation: sound-insulated air recirculation from AL-KO. All options available: PLC control for manual and automatic modes. Countless options from machine recognition to gate actuation to frequency-controlled operation, to name just three examples. Nothing left to chance: collection container with inspection window. Practical in every detail: container fastening with ergonomically shaped clamping lever. Expandable at any time: retrofit for discharge via briquetting press or rotary valve possible. - High extraction performance - Compact footprint - 100% air recirculation without temperature loss - (Residual dust < 0.1 mg/m³) - Integrated pre-separator and expandable control system - Optimal filter cleaning - Minimal noise level - Optional: patented fill level monitoring - Maintenance-friendly, certified automatic fire extinguishing system - Dust barrier for dust-free bin changes - (Optional: safety locking system for the containers) - Freely configurable module exchange and expandable ----- Technical Data ----- Extraction nozzle diameter: 350 mm, Nominal air flow rate: 6,927 m³/h, Maximum air flow rate: 8,500 m³/h, Maximum negative pressure: 2,543 Pa, Filter surface: 73 m², Chip collection volume: 3 x 250 liters, Number of bags: 3, Motor 400 V: 11.0 kW, Dimensions (LxWxH): 3,340 x 1,058 x 2,351 mm, Sound pressure level: 71 dB(A), Weight: 999 kg, according to: GS - HO - 07