Used Compactor for sale (463)

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, year of last overhaul: 2026, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Gbjdpsy S Rtlsfx Abgsn Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Gjdpfxey S Rqwj Abgobn Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: reconditioned (used), functionality: fully functional, machine/vehicle number: Pal 1600, power: 180 kW (244.73 HP), input voltage: 380 V, warranty duration: 12 months, Equipment: documentation/manual, 1 pellet press brand: Paladin 1600-210 inner diameter die 850 mm tread die 210 mm Press is equipped with 2 motors each 90 KW n=1500. Press door is made of stainless steel with overload valve in door. 3 Roll press with 3 rolls on the press overhauled in a drilled or racked version Press is complete with mold lifting device and tools The press is completely overhauled and equipped with new bearings and wear parts such as front and rear sliders die washer etc. Also new V-belts and toothed belt. Also, all safeties will be observed and appropriate switches on Friction safety , door switch and inspection hatches will be fitted. Refurbished pump unit for friction and V-belt tensioning Gbjdpfjq U R N Tjx Abgjn Remark: Conditioner on the press is optional

Condition: used, Year of construction: 2005, Chamber press - baling press Austropressen APV 300, used 🧰 Product features • Manufacturer: Austropressen • Model: APV 300 • Condition: Used item, see photos • Color: turquoise • Year of manufacture: 2005 • Dimensions: approx. 1620 x 1260 x 2920 mm • Own weight: 1650 kg • Pressing force: 300 kN • Cycle time: 45 seconds Gsdpfjxvy N Usx Abgebn • Power: 5.5 kW • Voltage: 400 V (12.5 A) • Bale weight: 300 - 400 kg 💰 Price: €7,200 net excl. VAT • Quantity discount: on request • Shipping: Europe-wide on request • Delivery time: Immediately available • Inspection and collection: possible at any time by appointment Constantly over 5,000 linear meters of pallet racking from various manufacturers in stock (Technical data, details, and prices subject to change and error, as well as prior sale! See our GTC, all prices excl. VAT ex stock.)

Condition: used, Year of construction: 2019, Chamber Press - Baling Press - Raw Material Press Bramidan X30 AD, used 🧰 Product Features • Manufacturer: Bramidan • Model: X30 AD • Condition: Used, see photos • Color: Orange • Year of manufacture: 2019 • Dimensions: approx. 1760 x 1255 x 2295 mm • Net weight: 1650 kg • Press force: 300 kN • Cycle time: 25 seconds • Power: 4 kW • Voltage: 3 x 230 - 440 V / 50/60 Hz • Noise level: 59 - 60 dB • Bale weight: Plastic up to 425 kg, cardboard up to 350 kg 💰 Price € 8,900 net excl. VAT • Quantity discount: on request • Shipping costs: Europe-wide on request • Delivery time: Immediately available • Inspection and collection: possible at any time by prior arrangement Constantly over 5,000 linear meters of pallet racking from various manufacturers in stock Godpfxsxvyn De Abgebn (Subject to changes and errors in technical data, information and prices as well as prior sale! See our terms and conditions; all prices excl. VAT ex stock.)

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Gbsdpfx Aevq Rtkjbgen Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: ready for operation (used), Year of construction: 2013, Brand: HSM Type: V-Press 1160 plus Year of manufacture: 2013 Pressing force: 532 kN Voltage: 400 Gsdey Uimvopfx Abgsbn Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feeding opening dimensions: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request.

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, Used Andritz Paladin 600B Incl. combined stainless steel feed auger and mixer, 2x 55kW motors, other motor options negotiable Interior inspected 2 years ago Gedox N T Uaepfx Abgebn Includes frame for roller and die change

Condition: ready for operation (used), Pressing force: approx. 700 kN (approx. 70 tons) Motor power: approx. 11 kW Godpfxera Dddj Abgebn Power supply: 3 × 400 V / 50 Hz Single bale weight: up to approx. 600 kg Bale dimensions: approx. 1100 × 1100 × 1200 mm Machine dimensions: approx. 5.9 m in length, 2.5 m in width, approx. 2.6 m in height Machine weight: approx. 7 tons Cycle time: approx. 45–47 s Construction features large feed opening for cardboard possibility of automatic feeding (e.g., via conveyor) manual wire tying (4 wires) pallet lock and hydraulic doors for bale removal Advantages of this press large bales = fewer transports high pressing force suitable for continuous operation Available production years: 2018–2020

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, For sale here is an ANIS ATS 110-75S-9CT-30kW baler, including cross-tying system (9-fold binding). The baler is in good technical condition and was only used sporadically. DIMENSIONS OF THE BALER - Total length: 9700 mm - Total width: 3700 mm Godpfjy Ayiqjx Abgebn - Transport width: 2300 mm - Height incl. chute: 3640 mm - Approx. total weight: 24 t - Ground pressure approx. 5 kg/sqcm - Heaviest part of the machine: approx. 6 tons CHUTE OPENING - Length: 1600 mm - Width: 1200 mm - Inspection door (glass) PRESSING CHAMBER - Piston stroke length: 2600 mm - WxH: 1100 x 770 mm - Volume: 2.2 cbm - The piston runs on solid rollers and is fitted with knives for cutting residual material. - The pressure on the pressing chamber (channel) is applied by two side cylinders and a simple lever system, allowing for consistent and even force distribution. HYDRAULIC EQUIPMENT - Siemens electric motor, 4-pole, 400V-50Hz, 30 kW - Hydraulic pump (Bucher) const./peak 320/400 bar - Max. working pressure 290 bar - Denison hydraulic valves 24 VDC - Pressure monitoring with proportional valve cycle - Automatic oil temperature monitoring - Automatic oil filter monitoring - Automatic oil level monitoring - Oil volume: 600L - Max. press force: 740 kN / 74 t - Specific pressure: 87 N/sqcm PLANT THROUGHPUT - Volume per press operation including pre-compression: 1.76 cbm - Average cycle time per press operation approx. 40+8 sec. - Cycle time without material 22+8 sec. - Binding time 30 sec. - Theoretical volume without binding 1.84 m3/h - Average working volume 123 m3/h - Capacity at material density 30 kg/m3: 3-4 t/h BALES - Bale length: 500 - 2000 mm - Bale width: 1100 mm - Bale height: 770 mm

Year of construction: 2018, condition: excellent (used), From 2018, 15 kW, with hopper and container PM 32-E (32 m3) and tipping device Gbsdpfxoyti Ipe Abgon

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, pressing force: 48 t, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 450 kg, Equipment: documentation/manual, HSM VK 4812 P Gjdpfsy Udzhsx Abgsbn Year of production: 2017 Fully automatic baler. The device has service and maintenance work by an authorized HSM service with a branch in Germany. Press after significant service work - details after direct contact. The baler comes complete with a ramp for ejection of finished bales and stands for binding wires. Pressing force: 480 kN Drive power: 18 kW Voltage / frequency: 400 V / 50 Hz Capacity at 50 kg/m³: 10.2 t/h Bale width x height x length: 1100 x 750 x 600 - 1200 mm Total length x width x height: 6661 x 3994 x 2583 Machine weight: 10.2 t Compressed material: foil, mixed paper, cardboard, die-cutter waste Bale tying: 4-fold with wire We also have other presses in stock. Transport costs depend on weight, volume and, above all, distance, the following information is important for inquiries: Delivery address (postal code and city name), but further details require telephone contact, so please inquire about transport costs and other delivery methods to contact us contact us by phone. Our contact details can be found in the seller's legal information. We sell and export worldwide, and thanks to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-Community invoices - without VAT. opening hours Mon-Fri: 8:00-16:00 Sat: closed

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 80 t, bale weight: 600 kg, Equipment: documentation/manual, DIXI 80 SLD horizontal press Semi-automatic press system with 80 tons of pressure for economical volume reduction of residual materials (recyclable) in industry and retail: Cardboard Tetra packs Films Foams PET bottles Insulating mats and other compressible materials. Pressure force : 80 t Gsdpfxjy Udwpo Abgjbn Electrical connection : 400 V 50 Hz; 11 kW; D-32 A (option: K-32 A) Cycle – average approx. : 35 sec Length approx. : 4,320 mm (without lifting device and pallet) Width approx. : 1,830 mm Height approx. : 2,620 mm (with hopper) Loading opening (WxD) – housing : 1,040 x 1,110 mm Bale dimensions : 1,120 x 1,120 x 1,200 mm Bale weight approx. : 500 – 600 kg Tying 4 manual, wires with quick-release eyelets Machine weight approx. 8,000 kg (without bale)

Condition: used, functionality: fully functional, Main Technical Specifications Machine Model: COMDEC LV 50-40 PFT horizontal baling press Pressing force: 50 tons Horizontal hydraulic baler for cardboard, paper and industrial waste Gjdpey Uddijfx Abgobn Electrical data Power supply: 380 V / 3 phase / 90 A Hydraulic motors: 2 × 22 kW hydraulic pump motors Conveyor pump motor Hydraulic system Hydraulic main cylinder: 180 / 150 × 2000 mm Hydraulic pressure control system with oil cooling and filtration Oil tank with pressure and return filters Machine dimensions Total machine length: approx. 8,394 mm Width: approx. 1,920 mm Height: approx. 3,104 mm Functional equipment Automatic wire tying system Bale length control system Hydraulic wire twisting unit Automatic bale ejection system Conveyor control cabinet and electrical automation system Noise level Working noise level below 70 dBA

Condition: excellent (used), Year of construction: 2010, ZENTEX PPH 5 baler is a device for compacting and crushing cardboard and foil. The baler makes it possible to reduce the volume of waste material and is ideal for warehouses, wholesalers and logistics companies. The cardboard baler is equipped with a swing door, maximum bale size 70x50x45 cm. Pressing time including return stroke 23 s. Advantages of the Zentex PPH 5 carton press: - Reduced volume of waste going to recycling - Saves time spent on waste management - Equipped with a module to compact paper and film - Prevention of space restriction by stored cardboard and foil in alleys and aisles. The offer concerns the Zentex PPH5 waste paper and film baler : - Manufacturer: ZENTEX - Product condition: used - Year of manufacture : 2010,2012,2013 - Model: PPH5 - Width: 84 cm - Depth: 72 cm - Height: 207 cm - Weight: 360 kg - Power: 1500 w - Voltage: 400 v Net price : 1890.00 euro each year of manufact. 2010 (Product code: MTP000234) 1990.00 euro each year of manufact. 2012 (Product code: MTP000235) 2090.00 euro each year of manufact. 2013 (Product code: MTP000236) Godpfxendcxge Abgobn The Zentex PPH 5 cardboard compactor is a professional device that effectively reduces waste. It bales waste into ready-to-collect bales, which are double-bound by strapping. The baler is ideal for companies with small quantities of waste, small wholesalers, food shops and clothing shops. * Large quantities available, prices can be negotiated for larger orders. * Transport throughout Europe possible. * The above offer does not include transport costs. * Location: Chmielów/Tarnobrzeg, Poland.

Condition: good (used), weight 120 kg length 800 mm width 600 mm height 330 mm Remaining stock of new and used milling cutters with bore, end mills, drills, dowel drills, inserts and various other cutters. Manufacturer: Leitz, Leuco, Oppold, and many more Interesting for every well-equipped sharpening room. Gsdjy Aa I Tjpfx Abgjbn

Condition: excellent (used), Professional plate compactor from the renowned brand AMMANN. Model AVP 2920 is equipped with a reliable HATZ Diesel engine with 5 kW of power. This machine is intended for professional paving, roadworks, and compaction of soil, paving stones, bedding, and asphalt. The unit is fully mechanical with a robust German construction. Visual condition as per the photos – normal signs of use. Technical data: • Manufacturer: AMMANN • Model: AVP 2920 • Year of manufacture: 1999 • Engine: HATZ Diesel • Engine type: 1B30-6 • Power: 5 kW • Operating weight: 190 kg Godpey Sifyefx Abgjbn • Manual start • Made in Germany Applications: • Compaction of paving stones • Paving works • Road construction • Soil and bedding compaction • Excavations and foundations Condition: Used machine, complete. HATZ engine – a durable and highly regarded diesel unit

Year of construction: 1982, condition: good (used), machine/vehicle number: 14320, Vertical Baling Press Godpfxjiuky Io Abgjbn

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h Gbsdpjy R Nnfefx Abgen bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: like new (used), Year of construction: 2025, functionality: fully functional, ALTERO VELOX 140 RECYCLING LINE Regranulation line for plastic recycling Brand: Altero Model: Velox 140 Feeding belt with metal detection Compactor/Agglomerator with 1500 mm diameter Gbjdpfx Aoy T R Dyebgon Screw diameter: 140 mm Double degassing unit Laser filter Granulation system with die-face cutter Centrifuge and vibrating screen Production up to 1100 kg/h Control panel with touchscreen Year 2025

Condition: excellent (used), Year of construction: 2016, bale weight: 480 kg, For sale: HSM HL 4809I baling press. Godpfx Absy T Iqdjgebn

Condition: used, Year of construction: 2021, functionality: fully functional, For sale: HSM 7009st baler and conveyor belt. Gbjdpfx Absy T Inpogon

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, pressing force: 50 t, bale length: 1,200 mm, bale weight: 500 kg, Equipment: safety light barrier, For sale: HSM 3521s machine, manufactured between 2015 and 2023. Gjdpfxoy T Empj Abgjbn

Condition: used, Year of construction: 2010, total width: 2,080 mm, total height: 1,900 mm, total length: 2,440 mm, Colour: Grey Briquette press; Höcker Polytechnik BrikStar C 3-19-L 4.3kW, 400V 25kg/h Funnel volume 3m³ Oil tank 50l Dimensions; 2015x2360x1300mm, 830kg - Year: 2010 - Documentation available: Yes - CE certificate present: No Gbsdjxqdxcopfx Abgon - Transport dimensions: 2440mm x 2080mm x 1900mm (l x w x h) - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2012, total width: 1,700 mm, total height: 1,500 mm, total length: 1,200 mm, Colour: Grey Empty weight: 500 kg Price: On request - Details: - └ Description: Set consisting of briquette press with extraction - Year: 2012 - Documentation available: No - CE certificate present: No - Serial number: 2012 1140 - Transport dimensions: 1200mm x 1700mm x 1500mm (l x w x h) - Transport weight [kg]: 500kg Gbjdsyy Rt Ujpfx Abgen - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels