Used Button Machine for sale (66,382)

Condition: ready for operation (used), Year of construction: 2010, x-travel 280 / 300 mm y-travel 250 / 270 mm z-travel 300 / 310 mm turning speeds 45 - 2240 U/min turning speeds 18 Stufen spindle taper ISO 40 quill stroke 60.0 mm table: 670 x 320 mm Gjdexabqnepfx Ak Ujug table load 150 kg feed range 12.5 - 630 mm/min feed 18 Stufen rapid traverse 1.200 mm/min workpiece weight max. 150 kg T-slots 5x 12 x 63 mm total power requirement 1.6 kW weight of the machine ca. 1100 kg range L-W-H 1265 x 1080 x 1620 mm New price ~ 25.000 Euro (!!) Special price upon request - in checked conditions - machinevideo - ?v=7IsC5cg9WlI Features: - Robust electric-driven universal milling machine - ACURITE 3-axis digital display * with pivoting control panel, front right * including emergency stop button - Electric adjustment of all axes (X/Y/Z axes) * Rapid traverse in all 3 directions - Pivoting milling spindle guard - Coolant system - Lower chip tray - Vertical milling head with quill adjustment * Milling head rotation 90° * Tool holder ISO / DIN 40 / 2080 - Fixed angle table 670 x 320 mm * T-slot width x spacing 12 x 60 mm * Minimum distance between base table and spindle axis - 4 machine feet - Electrical diagram

Year of construction: 2003, condition: good (used), functionality: fully functional, X-TEK RTR160UF: X-TEK Systems Ltd., England Model: RTR160UF Type: Ultra Focus X-Ray System Max. X-ray voltage: 160 kV Max. power: 60 W Focus size: 5 (Ultra Focus) Manipulator: 50 kg, 5 axes Power supply: 230 VAC, 50/60 Hz Serial number: RTR/124 Gujdpfx Aozl Scrjk Ueg Model: RTR160UF X-ray source: 160 kV, 60 W, 5 m Ultra Focus Manipulator: 50 kg, 5-axis Serial No.: RTR/124 Supply: 230 VAC, 50/60 Hz Specified cabinet leakage: < 1.0 Sv/hr at any point on the cabinet surface under the stated test conditions. This is an industrial cabinet X-ray inspection system, designed for high-resolution non-destructive testing (NDT) of components, electronics, castings, solder joints, and similar items. The 5 m ultra-focus source is intended for very high-resolution imaging.

Year of construction: 2017, condition: excellent (used), functionality: fully functional, Vacuum fryer used for vegetable chips. In very good condition. Located in The Netherlands. Guodpfoxg Tfqjx Ak Usg

Condition: new, Year of construction: 2023, No. 04377 Brushing and structuring machine VOLPATO SPO 600 Year of construction 2023, new, immediately available, made in Italy VOLPATO has been building grinding machines for over 60 years Working width 600 mm Machine open at the side for double pass and double grinding width of 1200 mm Electric height adjustment of both units independently of each other Maximum grinding height 330 mm (360 mm) depending on brush diameter both brushes tilt 0-10° (20°) Maximum diameter of brushes 320 mm Brush rotation infinitely adjustable 180 - 600 rpm Change of direction of rotation of the brushes possible Gjdpfeqrtv Rjx Ak Uoug Electric height adjustment 0 - 330 mm with Siko indicators Brushes are stored on round bars with a diameter of 90 mm each with linear guides Infinitely adjustable feed speed of the conveyor belt Table height thanks to adjustable feet 800-850 mm Suction nozzle 2 x 180 mm EMERGENCY STOP BUTTON Motor power of the grinding units 2 x 4 kW Motor power of the conveyor belt 0.55 kW Table dimensions 2000 x 860 mm Includes 1 steel wire and 1 Tinex plastic brush, each 250 mm diameter, 80 grit NET WEIGHT 700kg CE declaration of conformity Operating instructions in English Brush units inclined up to 20 ° with respect to the direction of movement = when the wood rusts, the veins are also highlighted transversely thanks to a helical action of the brushes The machine has 3 inverters, one for adjusting the belt speed and 2 for the brush units = many finishing configurations available Double direction of rotation of the brushes 4kW motors with belt transmission giving double torque to the brush units The images serve as an example and represent an identical machine Transport dimensions approx. 2100 x 1300 x 1900 mm LWH Weight 750kg To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold in AS IS condition According to the manufacturer, the warranty is 1 year after delivery Technical information, condition description, year of construction and scope of delivery according to the manufacturer's brochure or previous owner, without guarantee Subject to prior sale Any warranty is excluded for used machines. The rule is “bought as seen”. Terms of payment: Prices plus VAT, payment before collection or shipping Delivery conditions: ex warehouse or location

Condition: ready for operation (used), Year of construction: 2011, machine/vehicle number: 56.604, functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! MACHINE DETAILS Gsdszzbcyepfx Ak Ujug Supply voltage: 400 V AC Rated current: 29 A Number of phases: 3 Power: 17.1 kW Frequency: 50 Hz Short-circuit interrupting capacity: 10 kA RMS symmetrical EQUIPMENT Drilling tool Saw unit Vacuum pump Tools

Condition: excellent (used), Year of construction: 2009, clamping force: 3,000 kN, screw diameter: 65 mm, clearance between the columns: 710 mm, injection pressure: 2,070 bar, injection weight: 981 g, mold height (min.): 225 mm, Clamping Unit • Clamping force: 3000 kN (300 t) • Distance between columns: 710 x 710 mm – special design, increased distance compared to the standard version • Mold height: min. 225 mm / max. 1125 mm • Opening stroke: 900 mm • Maximum distance between mounting plates: 1125 mm • Mounting plate size: 1030 x 1020 mm (920 mm) • Special hole pattern in the clamping plate and nozzle plate – made to order • Manual device for removing the upper column, with a removable cover in the front guard and a wrench for the column nut Injection Unit • Injection unit 2250 • Screw diameter: 65 mm, L/D ratio 22.0 • Shot volume: 1078 cm3 • Maximum injection weight (PS): 981 g • Specific injection pressure: 2070 bar • Equipment package: wear and corrosion-resistant plasticizing unit, adapted for processing PP and PPSU, diameter 65 mm • Hart-PVC package: without internal screw cooling, with external cylinder cooling instead of standard design • High-temperature heating bands for a working temperature of 450 °C • 8 standard open nozzles, plus: 4 for the PVC cylinder and 4 for the PP cylinder, through holes 4, 8, 10, and 12 mm • Wrench for screw tip for a 65 mm diameter UNILOG B6S Control System - Upgrade package • Controller with increased computing power • APS and cycle time analysis • Four freely configurable network connections • Userpage and notepad • Real-value graphics with 16 curves • Event log depth: 10,000 events • Quality table memory depth: 10,000 events • Four envelope curves, foil function keys • SPC evaluation and trend charts Gujdpfezxfg Rsx Ak Ueg • Injection, holding, and back pressure controlled by a servo valve Hydraulics and Hydraulic Cores • Core movement and parallel ejection are performed by an additional DFEE pump, size 71, flow rate 95 l/min • 4 x hydraulic core for the clamping plate NW 10 (on/off valve), interfaces according to EUROMAP 13, with active ejector plate protection • Cores mounted on the upper side of the clamping plates, each with connections for two consumers • 2 x core junction box in a special design: 25 3-pole Amphenol plugs, mounted on the clamping plate on the operator side and the rear side, connected in series • 4 x core pressure relief upon emergency shutdown, engine stop, and after pressing the button in setting mode – relief occurs simultaneously for cores on the clamping side and the nozzle side • 4 x twin check valve for NW 10 core • 2 x pneumatic valve for controlling one closing nozzle in the mold or several in parallel (1000 l/min), mounted in the center console at the rear of the machine Mold Heating, Electrical System, and Connections • 12 x temperature control circuit for hot runner or mold heating, power 2.3 kW, 10 A, interface according to HASCO standard (1 x HASCO 24-pole for max. 6 zones) • Mounting location for heating circuits: center console at the rear, near the control cabinet • 2 x Schuko 16 A socket: under the control system and on the clamping side from the rear, under a cover • 2 x CEE 16 A socket: on the injection side from the front and on the clamping side • Dual power supply: 1. power supply 3P+N, 400 V, rated current 140 A, preliminary protection gL-gG 160 A • 2. power supply 3P, 400 V, rated current 98 A, preliminary protection gL-gG 100 A

Condition: used, Year of construction: 2021, functionality: fully functional, machine/vehicle number: A/18031, SCHULER - MSP2-800- 4,5x1,8-400 Kapasite: 800 ton Hava Tüketimi: 30 m³/saat Güç: 296 kW Üst Tabla Ebatları: 4500 mm x 1700 mm Alt Tabla Ebatları: 4500 mm x 1800 mm Pres Yükseklik: 7,5 m Pres En: 6,50 m Pres Genişlik: 4,50 m Dakikadaki Vuruş Sayısı(maksimum): 70 spm Godozxqz Tspfx Ak Uoug Çalışma Reglajı: 300 Kurs Değeri: 80-360 Used machine

Condition: new, functionality: fully functional, Year of construction: 2025, machine/vehicle number: 250506-mxa-03, control type: CNC control, degree of automation: automatic, actuation type: electric, controller manufacturer: Raytools, laser type: fiber laser, laser source manufacturer: MAX Photonics, laser power: 1,500 W, sheet thickness steel (max.): 15 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 6 mm, sheet thickness brass (max.): 4 mm, table length: 3,000 mm, table width: 1,500 mm, table height: 600 mm, working length: 3,000 mm, working width: 1,500 mm, cutting speed: 5,000 mm/min, input voltage: 380 V, input current: 45 A, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, overall weight: 2,400 kg, total length: 4 mm, total width: 3 mm, total height: 2 mm, warranty duration: 3 months, air pressure: 16 bar, Equipment: CE marking, centralized greasing system, cooling unit, emergency stop, Fiber laser metal cutting machine — 1500 W MAX Photonics (Senke SKL-1530F) Brand new, unused — still sealed in original factory export packaging (0 operating hours). Immediately available. High-precision, long-term stable and affordable fiber laser cutting for professional sheet-metal work. Ideal for metal fabrication shops and repair workshops. Delivered as a complete, ready-to-run package. Complete package — key features: ● MAX Photonics fiber laser source, 1500 W ● DELTA servo motors & drives (1500 W X/Y, 400 W Z) ● Raytools control system with RayTools BM110 cutting head ● Large 1500 x 3000 mm working area (fits a full standard sheet) ● Open-frame design — easy access and loading of oversized plates ● Reinforced, stress-relieved welded steel bed for lasting dimensional stability ● Taiwan YYC gear rack + HIWIN 25 square rails + TBI ball screw (Z) ● Positioning speed up to 150 m/min · cutting speed up to 7 m/min (material/thickness dependent) ● S&A industrial water chiller ● France Schneider electrics · SMC pneumatics · France Motoreducer · automatic central lubrication ● Included air compressor (15 kW, 1.6 MPa, 340 L tank) — enables low-cost cutting with compressed air, so bottled nitrogen/oxygen is reserved only for jobs that require it. Lower running costs and greater gas autonomy from day one. ● Included 30 kVA voltage stabiliser — stable power supply, protects the electronics Gedpfx Asztn N Djk Usug ● Included spare consumables: 100 protective lenses + 100 copper nozzles — full starter set of wear parts Materials: carbon steel, stainless steel, aluminium, brass and other sheet metals — sheet-metal processing, auto parts, metal crafts, chassis/cabinets, kitchenware and similar industries. Sales exclusively to commercial businesses. Machine located in Jõhvi, Estonia — viewing by appointment; INCOTERMS: EXW

Condition: ready for operation (used), Year of construction: 2005, operating hours: 10,197 h, functionality: fully functional, travel distance X-axis: 1,300 mm, travel distance Y-axis: 710 mm, travel distance Z-axis: 710 mm, controller model: Fanuc 18i-MB, spindle speed (max.): 10,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel in X-axis: 1,300 mm Travel in Y-axis: 710 mm Travel in Z-axis: 710 mm B-axis rotation: 360° Gujdpszzbbcefx Ak Usg Number of axes: 4 Table length: 1,500 mm Table width: 660 mm Tool interface: ISO 40 Max. spindle speed: 10,000 rpm Power: 38.4 kW Tool magazine capacity: 32 MACHINE DETAILS Control system: Fanuc 18i-MB Dimensions & Weight Dimensions (L x W x H): 4,300 x 3,250 x 3,080 mm Shipping weight: 7,000 kg Shipping packages: 4 Operating hours: 10,197 h EQUIPMENT CE marking

Condition: used, Year of construction: 2009, - Veneer strip lengths (fiber direction): 350-1500 mm - Veneer strip widths (cross-fiber direction): 50-500 mm - Veneer surface width (cross-fiber direction): min. 260 mm - Veneer strip thickness: 0.3-1.5 mm Veneer machine with direct stacking Manufacturer: Fischer & Rückle Type: FZR 15 / DAR 22 Year of manufacture: 2009 Cross-feed splicer For the most efficient cross-gluing of parallel-joined veneer strips into endless or component-specific veneer surfaces. The cut or rotary-cut veneers must be pre-glued, using PVAc or urea adhesives. This cross-feed splicer is the most economical alternative to longitudinal splicers for cross-fiber applications. Production Approx. 17-20 joints/min Technical data Veneer strip lengths (fiber direction): 350-1500 mm Veneer strip widths (cross-fiber direction): 50-500 mm Veneer surface width (cross-fiber direction): min. 260 mm Veneer strip thickness: 0.3-1.5 mm Equipment Feeding device for efficient and convenient semi-automatic feeding of veneer strips. Panel automatic for component-specific surfaces with pre-sorted components and a pre-selected number of veneer strips. Features - Perfect bonding of cut or rotary-cut veneer of all wood species, even with wavy or undulating veneer - Unique, tried-and-tested horizontal pressing system that results in completely closed, solid glue joints Godpfx Aszuz Hljk Usug - Solid, robust construction for a long service life, reliable and fail-safe operation - Easy operation thanks to screen, clear symbols, separate pressure gauge with direct access, etc. - Liftable pressure beams for quick and easy access to the heating plates for cleaning - Few wear parts, low costs for service and maintenance Cross-cutter For cutting to a pre-set format width (across the fiber direction) immediately after splicing. The straight alignment of the veneer must be observed and, if necessary, corrected by pressing a button. When working in endless mode, the required distance to the direct stacking device is set. Direct stacking device DAR-22 For outputting and stacking the veneer surface immediately after splicing or cutting. The spliced surfaces are gently output and stacked without this compact direct stacking device exerting any mechanical forces. Min. veneer sheet lengths (fiber direction): 350* - 1500 mm Veneer sheet widths (across the fiber direction): 260 - 500* - 2200 mm Stack removal from the left, right, or rear Max. stack height: 500 mm *Reliable stack alignment not guaranteed Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, TEUREMA EHS-110 WIRE DRAWING LINE Year of manufacture: 1999 Maximum speed: 10 m/s Total installed power: 230 kW TEUREMA EHS-110 wire drawing line with robust construction, equipped with a Tecno Impianti drawing bench and prepared for industrial use. The machine has undergone a complete electrical modernization, including a new main electrical panel, Siemens S7-1500 PLC, Siemens 1200 HMI screen, 100% new wiring, and new push-button stations, which significantly improves the reliability, maintenance, and operability of the unit. LINE COMPOSITION Coil stands - 2 tilting winders - Maximum capacity per winder: 3,000 kg Vertical winding tower - 6-meter tower - Lifting and lowering carriage with a hoist Mechanical decaling unit Soaping unit - Motor: 1.5 kW - Speed: 1,500 rpm TECNO IMPIANTI DRAWING BENCH - Number of steps: 2 - Two-ring coil: - 1st ring: Ø 610 mm - 2nd ring: Ø 760 mm - 3-speed gearbox: - 3.90 m/s - 7.20 m/s - 10.00 m/s - Power: 160 kW - Frequency: 50 Hz Horizontal coiler - Horizontal drive - Maximum coil capacity: 3,000 kg - 2-speed gearbox: - 7.3 m/s - 10.0 m/s Guodpfozycakex Ak Ueg - Maximum coil diameter: Ø 1,200 mm - Core diameter: Ø 600 mm - Usable width: 900 mm - Power: 45 kW TECHNICAL DATA - Inlet diameter: 5.5 to 14 mm - Outlet diameter: 4 to 12 mm - Number of blocks: 1 vertical - Maximum line speed: 10 m/s - 2 CL30 A 33 Eurolls cassettes - Rollers: Ø 150 x Ø 90 x 15/20 mm - Total machine power: 230 kW - Frequency: 50/60 Hz ELECTRICAL AND AUTOMATION UPGRADE - Completely new main electrical panel - Siemens S7-1500 PLC - Siemens HMI 1200 screen - 100% new wiring - New push-button stations - New programming AVAILABLE SERVICES Possibility of supply with: - installation - assembly - commissioning - technical assistance - adaptation according to customer needs

Condition: ready for operation (used), Year of construction: 2001, sheet width 3200 mm plate thickness 3.0 mm ST thickness at "Niro-steel" 2.0 mm Opening width / upper beam 300 mm speed OW 40.0 mm/sec Bending beam adjustment 80.0 mm work height max. 900 mm speed BW 90.0 Grad/sec control MULTIBEND 5000 back stop - adjustable 10 - 1550 mm accuracy +/- 0.1 mm air pressure 5.0 bar Number of working hours ca. 1.000 h voltage 400 V total power requirement 2x 4.0 kW weight 4400 kg range L-W-H 4295 x 2225 x 1775 mm New price approx. 85.000 euros Machine with only approx. 1.000 operating hours (!!) good condition (!!) Godpfx Akexabz To Uoug Special price on request - in checked condition - machine video - ?v=VP6emx4HTYM ! Maximum flexibility when bending cassettes, boxes and profiles ! High flexibility in bending part design ! High productivity and throughput ! Easy to use Equipment: - motorized universal swivel bending machine "RAS 73.30" * high-precision mechanics with modern control technology * for individual and series production * robust high-speed machine with high axis speeds * torsion-free welded construction - RAS CNC control model "MULTIBEND 5000" * material and tool library * swiveling - front right * 1x emergency stop button - CNC electro-motorized upper beam adjustment * fast closing and opening speed * programmable opening and closing height * bending radii without special tools (multiple bends) * rigid upper beam for straight bending parts * 1x set of RAS split upper tools .. height 80 mm * RAS "click-in" tool system - CNC electro-motorized bending beam adjustment * fast swivel movement: short production time * crowning system compensates for deformation by the bending forces * 1x set of RAS split bending tools - CNC electro-motoric back stop * fast positioning, repeatable work * table plates hold the weight of the sheet * stainless steel table plates with ball rollers - 2x freely movable double foot switch - 1x RAS tool trolley for bending tools (movable) - operating instructions (PDF) + original circuit diagram

Condition: good (used), Year of construction: 1976, max. wheel diameter 2300 mm Gedjzr Rpdjpfx Ak Ueug gear width 1000 mm max. module 22 min. module 1 total power requirement 45 kW weight of the machine ca. 22 t dimensions of the machine ca. 5x3x4 m

Condition: good (used), Year of construction: 1976, max. wheel diameter 1250 mm gear width 1000 mm max. module 16 Gedozr Rpkspfx Ak Ujug shifting 250 mm milling spindle speeds (infinitely variable) 32 - 200 U/min min. number of teeth 12 table hole 255 mm total power requirement 32 kW weight of the machine ca. 20 t dimensions of the machine ca. 5,1 x 3,2 x 3,7 m Top condition! 2 cut cycle, change gears, arbors, chip conveyor. Following hob arbors are with the machine: Diameter: 32 , 40 , 50 , 60 mm

Condition: used, Year of construction: 2002, sheet width 3050 mm plate thickness 3.0 mm ST pre-bending capacity 3.0 mm ST upper roll diameter 170 mm lower roll diameter 170 mm side roll diameter 180 mm Control konv. 0 380 V total power requirement 3.0 KW weight 4250 kg In good condition With new rubber-coated top roll (!!) Also suitable for bending non-ferrous metals - in checked conditions - machinevideo - ?v=ZW8Us6Hbm3E Equipment: - Electro-hydraulic 3-roll bending machine - Asymmetrical roll arrangement - Electro-motor-driven side roll adjustment * Including digital position display - Manual bottom roll adjustment * Via hand crank - Including conical bending device * Inclined bottom roll and side rolls * Parallel alignment in any side roll position - Hardened rolls SAE 1050 CK 45 - Manual folding storage for removing closed pipes * Top roll must be raised before opening the storage (e.g., forklift/crane) - Safety device - Connection cable + connector - 4-way foot switch * 2 buttons for side roll movement (up/down) * 2 buttons for roll movement (left/right) Gedpjxacfgefx Ak Ueug * With 4x new foot switch covers - Operating instructions (English) * Special accessories included: - Brand new top roller with plastic/rubber coating * Suitable for bending non-ferrous metals * Such as copper and aluminum

Condition: new, COLUMN DRILLING MACHINE UNIMAX 3 Comparable to Alzmetall, Flott, etc. Powerful, precise column drilling machine with a wide range of applications. Drill table adjustable via rack and pinion and worm gear, and swiveling around the column. Forward/reverse switch, emergency stop button, digital speed display Infinitely variable spindle speeds Range A: 80 - 1440 rpm Range B: 180 - 3200 rpm Continuous drilling capacity: 25 mm Nominal drilling capacity: 30 mm Thread cutting capacity: M20 Spindle: MK 3 Drilling depth: 125 mm Throat depth: 260 mm Spindle/table distance: 90 to 840 mm Table surface: 500 x 365 mm Overall height: 1855 mm Weight: 250 kg Incl. drilling package, consisting of: Gsdpfxewkhlis Ak Ujug 1 drill chuck arbor MK3 / B16 2 reducing sleeves MK3 / 2, MK3 / 1 1 machine vice MSP 140 1 keyless drill chuck 1 - 16 mm / B16

Condition: new, Year of construction: 2026, Suitable for Outer pipe diameter Ø 26.9(3/4″) Ø 33.7(1″) Ø 42.4(1_¼") Ø 48.3(1_1/2″) Ø 60.3(2″) Outer pipe diameter for zinc spout Ø 22 - Ø 76 Advantage: Quick and easy notching Wall thickness (steel): 5 mm Wall thickness (stainless steel): 3 mm Weight: 93 kg Operation: Electric (2.2 kW) Application: Round, square and rectangular tube Easy to operate Gjdpfx Akezzk Ewo Ueug With the motorized pipe notcher AL1-2U you can notch pipe outside diameters of Ø26.9 (3/4″), Ø337 (1″), Ø42.4 (1 ¼"), Ø48.3 (1 ½"), Ø60.3 (2″) and pipe outside diameters for zinc flow from Ø22 to Ø76. The machine is started at the push of a button and the pipe notcher is driven continuously. This allows the user to continue production without having to switch the machine on every time. Electrically driven With the motorized pipe notcher AL1-2U you can notch pipe outside diameters of Ø26.9 (3/4″), Ø337 (1″), Ø42.4 (1 ¼"), Ø48.3 (1 ½"), Ø60.3 (2″). Do you often notch pipes? Then the motor-driven pipe notcher AL1-2U with 2.2 kW electric motor is the solution for you! The motor forms a single unit with the special eccentric shaft that drives the punching tool. In addition, the motor is equipped with an on/off switch with 0-voltage protection and a protective cap.

Condition: good (used), Year of construction: 2010, For sale CNC 5-Axis Drilling / Sinker EDM Machine – OCEAN Technologies OCT-90120CA (2010) 📝 DESCRIPTION For sale: High-precision 5-axis CNC drilling / sinker EDM machine from OCEAN Technologies Co., Ltd., model OCT-90120CA. This is a very large-capacity industrial machine, ideal for quickly drilling deep holes and machining complex cavities in the mold making, aerospace, and precision engineering industries. ⚙️ FEATURES AND TECHNICAL CAPABILITIES 📐 Travels and Machining Capabilities (5 Axes) X-axis travel: 900 mm Y-axis travel: 1,200 mm Z-axis travel (Vertical axis): 1,000 mm W-axis travel (Head guide): 350 mm Gusdpfjzrfpxsx Ak Usg Rotary axis / Dividing head (C-axis): Integrated rotary table for multi-angle positioning and machining without re-fixturing the workpiece. 🖥️ Numerical Control & System Operating system: Dedicated Windows XP Embedded. Interface: Ergonomic control panel with color screen, full industrial keyboard, speed potentiometers, and manual axis control buttons. ⚡ Electrical Specifications (Nameplate) Voltage: 400 V AC / 3 Phases / 50-60 Hz Capacity / Power: 35 KVA Overload current: 86 A Compliance: CE marking 🛠️ EQUIPMENT & INCLUDED ACCESSORIES Precision rotary table / chuck with grooves and fixing flanges. Complete filtration system and auxiliary chiller unit for dielectric fluid (RBSystem / Spracflo). Enclosed booth and protective housing with sliding doors. Adjustable control station and manual remote control. 📊 CONDITION & HISTORY Year of manufacture: March 2010 Serial number: DR06461209 Overall condition: Good working condition, machine is clean and maintained in a controlled industrial environment. Maintenance: Regular maintenance performed.

Condition: good (used), Year of construction: 2001, sheet width 2020 mm plate thickness 1.5 mm ST bending angle max. 180 ° Swing beam adjustment ca. 20.0 mm Bending time for 90° 5.5 sek Control konv. voltage 380 V total power requirement 1.5 kW weight 1180 kg range L-W-H 2650 x 1230 x 1100 mm Features: - Simple electric motor-driven swivel bending machine - Manual depth/material stop * Stepless adjustment up to a maximum of 700 mm * Adjustment via handwheel from the rear * Analog position display - Simple manual angle adjustment - 1x bending tool set * With bending rail .. 10 mm Godpfx Akjzr Rqho Ueug - Manual lower crossbar adjustment .. approx. 20.0 mm - Emergency stop button on the front - 1x freely movable double foot switch - Operating instructions (DK)

Condition: new, Year of construction: 2024, functionality: fully functional, Brand new machine never used, selling at very low price. Guedpfxswcfvpo Ak Ujg

Condition: used, Year of construction: 1962, serial number 813 stroke 160 mm automatic feeds ja cross-moving table 2-Achsen weight of the machine ca. 1,2 t Gedpfsz Alc Hjx Ak Ueug

Condition: used, New 2013 Table size 1474 x 356 mm X axis 1016 mm Y Axis 596 mm Z Axis 584 mm (Head Traverse) Spindle Speeds 40 – 5000 rpm & 40ISO 7.5 hp Spindle Drive. Max Table load 850 kg Gedpfoyhdi Rex Ak Uoug

Condition: good (used), Year of construction: 2014, functionality: fully functional, Immediately available, maintenance and safety inspection new as of July 30, 2026! Description Year of manufacture: 2014 Bending length [mm]: 1020.00 Press force [tons]: 36 Control system: TRUMPF TASC 6000 Standard equipment Machine - Stable machine frame - Press beam - Highly dynamic, electromechanical direct drive (torque motor) - Inductive length measuring system with temperature compensation - Switch cabinet air conditioning Gjdpfszrwntex Ak Uoug - Ergonomic machine design Back gauge system - Rear back gauge system, 6 axes Tool clamping - Upper tool clamping, automatic - Lower tool clamping, automatic Control system - TRUMPF TASC 6000 integrated - Numerical workshop programming - Windows XPe (embedded), Pentium M with 1.1 GHz clock frequency - 1 GB RAM - 15-inch touch screen Safety - Laterally pivoting safety doors - Protective cover at the rear - 2-button foot switch, for standing and seated operation - Rear back gauge system, 6 axes Ergonomics package: - Comfort support table (front) - Comfort footrest - Work area lighting front and rear (LED) - 2 document holders - 2 storage consoles - 1 measuring tool storage Productivity-Plus package: - Graphical workshop programming - Automatic tool clamping - BendGuard (with block laser) - Swiveling control panel - Bending line laser - Seat and standing aid - OCB – Operator Controlled Bending

Condition: new, neu ca. 2 - 4 Wochen ab Auftr Deutschland 3649.63 € 15 mm MK 2 220 mm 40 - 4000 U/min 0,75 kW M12 400 mm 520 mm 850 mm 65 kg 70 mm 85 - 370 mm 300 x 250 mm 70 mm Gsdpfx Aksy Hf Nwe Ujug PLUS - CONTROL PANEL WITH FOLLOWING FUNCTIONS: - Display - Operation via function keys and rotary/push button - Drilling mode / Tapping mode - Zero point setting - Drilling depth adjustment - Infinitely variable speed adjustment - Piece counter - Spindle stop function (spindle stops automatically after drilling) Drilling capacity / normal drilling Performance 15/18 (in E335/ST60) 17 Nm Thread cutting system Control panel with OLED display Robust, high quality drill head hood with ergonomically inclined front LED lighting Quickly adjustable and ergonomic Drilling depth stop Stepless speed control via central rotary knob EMERGENCY STOP pushbutton Thermal overload protection Spindle stop Drill protection with electr. Fuse Connection cable with Schuko plug 3 years warranty for single shift operation OPTIONS (PRICES ON REQUEST): Machine cabinet with door and drawer Drill package (vice & keyless chuck)

Condition: new, diameter 150 mm workpiece length 1300 mm work piece width 800 mm max. dia. of grinding wheel 150 mm milling-head swivable +/- 180° work height max. 945 mm turning speed range 0 - 1400 U/min engine output 1.5 kW weight of the machine ca. 230 kg. dimensions of the machine ca. 1435 x 1100 x 1510 mm The "Easy T" is the cost-effective alternative to the conventional ones grinding and deburring machines. His head consisting of a grinding wheel and a flap brush, can be swiveled by 180°. Thus, a faster Switching between the aggregates possible. Due to the weight-bearing arm the head can be easily moved Gjdpfexab Hpjx Ak Ujug over the workpiece. The result is one even edge rounding. The pad also prevents slipping of the smallest components. Furnishing : - Deburring and rounding of laser-cut or stamped sheet metal parts - Grinding head, consisting of a grinding wheel & a flap brush, can be swiveled by 180° - Working area 800 x 1300 mm - Weighted arm for easy pivoting - non-slip table pad - Ergonomic operation of the machine with the help of push buttons "On/Off" - Grinding head with infinitely variable speed via frequency converter - Handle for ergonomic handling