Used Dowelling Machine for sale (64,885)

Condition: like new (used), Year of construction: 2005, functionality: fully functional, GÖTZINGER RBS Dowel and Stair Drilling Machine, Swiveling with Laser In very good condition, the machine has been used very little and is in absolutely like-new condition; it comes from an educational institution. It can be used to drill dowel holes and similar. The machine has a BKF-5 drilling head with 5 drill chucks, M10 internal thread. The distance between the drill chucks is 32 mm horizontally and 25 mm vertically. The entire drilling head can be swiveled 360° with a degree indicator and various scales. A standard 2-jaw chuck can also be used. You will also receive 3 additional drill chucks for drills with a cylindrical shank of 12 or 16 mm, and for drills with an M10 external thread. The machine table is 1100 mm wide and 250 mm deep. There is a stop at the front that can be recessed if needed. For the production of dowel joints, there are 2 adjustable angle stops on the machine table, which can be set with an accurate scale. In addition, there are two 2500 mm long stop rails with 2 folding stops and a scale each; these stop rails can be mounted on the left and right. The machine drills completely automatically, which was problematic with larger drill diameters. For this reason, the machine has been converted to manual feed via a feed lever and switch. The workpiece is clamped with 2 pneumatic clamping cylinders; the switch is located directly on the clamping cylinder. Chedpfjzgh Tvsx Aatod 380V, 2100W 2820 rpm Year of manufacture: 2005 Weight: approx. 300 kg With this machine, you can produce all types of frame dowel joints, at right angles, butt joints, and miter joints. Ideal for the production of dowel joints in timber frame construction, furniture, door and window construction, and similar applications. Stairs can be manufactured very well due to the swiveling capability. The drilling unit can be swiveled to both sides up to 65° with a scale and has a detent at 0°. This allows handrails to be drilled very well into stair stringers with the machine. Due to the stops, the drilling head, and the construction of the machine, dowel joints are produced in a very short time, which makes the machine very economical. The machine requires a compressed air connection of 6 bar (the air consumption is very low). Right-hand rotation. Mills and drills very well and cleanly. The linear laser at the top of the machine allows marked dowel holes and angles to be drilled very quickly and accurately. The max. drilling height is 100 mm; the drilling height is adjusted at the front under the machine table with a handwheel. The height can be read on a very precise, mechanical counter. The max. drilling hole depth is 190 mm with a stop and scale. The max. workpiece height is 360 mm. Everything functions perfectly. Comes with a manual. We will personally deliver and demonstrate the machine anywhere in Germany for 220.00 euros. This means you have no risk when purchasing. Delivery to Austria and the rest of the EU is also possible upon request. Professional equipment, not hardware store junk. You can start working with the machine immediately. Very stable and durable construction. The precision guides with the backlash-free ball bearing bushings are in good condition and move easily. The swiveling mechanism is also very smooth due to the 2 groove ball bearings; locking is possible with a locking screw.

Condition: like new (used), Year of construction: 1994, functionality: fully functional, HOFFMANN HT 200 Dowel and Slot Drilling Machine In very good condition, this machine comes from an educational institution, has been used very little, and is in absolutely like-new condition; it has only very few signs of wear. It can be used to mill slots and drill dowel holes; the drilling height can be read very precisely on a digital counter. Comes with 3 drill chucks: for drills with an M10 external thread and for drills with 12mm and 16mm shanks. With workpiece support rests on the left and right sides, which are pivotable and have a support roller. The machine has a chassis. With 2 angle stops on the machine table for left and right. The clamping arms are reversible and adjustable. 380V, 1400 and 1800W through the 2 speed ranges. 1400 and 2850 rpm. Year of manufacture: 1994 Weight: approx. 280 kg With this machine, you can mill slots for, e.g., lock cases and similar items, or produce all types of frame dowel joints at right angles, butt joints, and miter joints. Ideal for producing dowel joints in timber frame construction, furniture, door, window, and staircase construction, and for similar applications. The drilling unit can be pivoted on both sides up to 65° and has a detent at 0°; this allows the machine to also be used to drill handrail posts into staircase stringers. Chedjyy Rtzepfx Aatod The 2 speed ranges allow drills with large diameters to be used without overheating during drilling. Due to the detents and stops and the machine's design, dowel joints can be produced in a very short time, making the machine very economical. The machine requires a compressed air connection of 6 bar (the air consumption is very low). Right-hand rotation. Mills and drills very well and cleanly. Workpiece clamping is done with 2 pneumatic clamping cylinders via a foot pedal. The linear laser at the top of the machine allows marked dowel holes and angles to be drilled quickly and accurately. Comes with a precision 12mm guide rail with a center detent and 13 detents on the left and right. Working travel in width: max. 330mm The max. borehole height is 90mm. The max. borehole depth is 200mm with stop. The max. workpiece height is 150mm. Everything functions perfectly. Comes with manual. We will personally deliver and demonstrate the machine anywhere in Germany for €220.00, so you have no risk when purchasing; delivery to Austria and other countries is also possible upon request. The machine table is 1100mm wide and 250mm deep. Professional equipment, not cheap hardware store junk. You can start working with the machine immediately. Very stable and durable construction. The precision guides with the play-free ball bearing bushings are in good condition and move smoothly; the pivoting mechanism is also very smooth due to a ball bearing; locking is possible with a locking screw.

Condition: used, Year of construction: 2024, DOWEL HOLE DRILLING MACHINE GANNOMAT "DB 21400V, 3Ph, 50Hz / 1.5 kW, complete in standard design with: - Fully automatic electronic control with pulse operation via foot valve for clamping-drilling-releasing, electric intermittent operation. - Automatic retraction of the drilling unit after reaching the set drilling depth. - Automatic extension of the drilling hole depth when drilling on the end face. This eliminates the need to adjust the drilling hole depth from flat-face to end-face drilling (+10 mm, e.g. for a dowel length of 35 mm, drilling depth on the flat face 14 mm and drilling depth on the end face 24 mm). - 1 drilling bar with 21 spindles, pitch 32 mm, motor 1.5 kW (drilling feed 0-70 mm), incl. 21 quick-change chucks (Ganner system) for easy changing of the drill bits. - Easy pivoting of the drilling unit from 0° to 90°, supported by gas cylinders. - 1 clamping support movable in the Y-axis with 3 pneumatic clamping cylinders, for workpiece height up to max. 80 mm. Ideal stop system consisting of: - 1 stop rail 1800 mm for drilling shelves (aluminum profile 40x40 mm) with 3 stop blocks, with quick-change system, easily interchangeable from right to left stop side for drilling shelves in carcass structures in mirrored fashion, also suitable for row drilling in the 32 system. - Side stops and position settings, as well as the position of the drilling height above the support table, are adjusted by means of mechanical digital counters. - Side stops can be easily pivoted away, for the shortest possible conversion from carcass to frame and row drilling. - Clamping arms for the clamping support designed for row drilling positions up to max. 300 mm. - Ideal three-stage tool system. - 1 set of drill bits for dowels: - 5 carbide dowel drill bits, Ø 8x77 mm, right-hand - 4 carbide dowel drill bits, Ø 8x77 mm, left-hand Basic machine DOWEL HOLE DRILLING MACHINE GANNOMAT "DB 21400V, 3Ph, 50Hz / 1.5 kW, complete in standard design with: - Fully automatic electronic control with pulse operation via foot valve for clamping-drilling-releasing, electric intermittent operation. - Automatic retraction of the drilling unit after reaching the set drilling depth. - Automatic extension of the drilling hole depth when drilling on the end face. This eliminates the need to adjust the drilling hole depth from flat-face to end-face drilling (+10 mm, e.g. for a dowel length of 35 mm, drilling depth on the flat face 14 mm and drilling depth on the end face 24 mm). - 1 drilling bar with 21 spindles, pitch 32 mm, motor 1.5 kW (drilling feed 0-70 mm), incl. 21 quick-change chucks (Ganner system) for easy changing of the drill bits. - Easy pivoting of the drilling unit from 0° to 90°, supported by gas cylinders. - 1 clamping support movable in the Y-axis with 3 pneumatic clamping cylinders, for workpiece height up to max. 80 mm. - Ideal stop system consisting of: - 1 stop rail 1800 mm for drilling shelves (aluminum profile 40x40 mm) with 3 stop blocks, with quick-change system, easily interchangeable from right to left stop side for drilling shelves in carcass structures in mirrored fashion, also suitable for row drilling in the 32 system. - Side stops and position settings, as well as the position of the drilling height above the support table, are adjusted by means of mechanical digital counters. - Side stops can be easily pivoted away, for the shortest possible conversion from carcass to frame and row drilling. - Clamping arms for the clamping support des Csdpfxoxnlflj Aatshd

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, FELDER FD21 Pro – Manufactured in 2024, in top condition Equipment: * 21 drilling spindles including a quick-change system Cedpfxjz Abu Ee Aatshd * 8mm drill bits * Precise adjustment options via rotary dials * Robust and high-quality construction * Display for width adjustment (self-built) * Cross rails for series drilling If you are interested or have any questions, please feel free to contact us. Viewing is possible by appointment. For sale due to a change in machinery.

Condition: ready for operation (used), Number of spindles: 8 Motor: x2 1.5 kW Pressure: Pneumatic Maximum working height: 120 mm Chedo Agvh Nepfx Aatod Working width: 850 mm

Condition: used, Year of construction: 1985, Used Machine Year of Manufacture: 1985 Features and Technical Specifications: - For horizontal and vertical structural drilling - For vertical row drilling in a 32 mm grid - Vertical drilling unit with dual-spindle drill heads, freely positionable on an indexing shaft - 1.5 kW motor with 1,400 rpm - 1.5 kW motor with 2,800 rpm - Drill heads with pneumatic stroke Cedpjzk N Dwsfx Aatehd - Pneumatic workpiece clamps - Passage width approx. 850 mm - Includes various stops and drill bits - Machine needs to be inspected/serviced. Basic functions are intact Availability: available shortly Location: 63934 Röllbach

Condition: used, Year of construction: 2018, 1 x CNC-CONTROLLED DRILLING, GLUING AND DOWEL INSERTING MACHINE GANNOMAT "INDEX 130 PRO" (with options as Index 180 Pro) 400V, 3Ph, 50Hz complete in standard design with: - Support with linear guide consisting of: 1 x single-spindle horizontal drilling unit, 1.1 kW motor, tool speed selectable via operator software (3000/5000/8000 rpm) 1 x blow-out, gluing and dowel inserting station in reinforced design for dowels Æ 8 mm, dowel length 30 mm - fully automatic, electronically controlled central lubrication - X-axis NC controlled, with working length 1300 mm, travel speed max. 78 m/min. - Z-axis, position via support table 5-40 mm programmable with NC-controlled Z-axis option - Dowel driving overhang of 7-20 mm, programmable with NC-controlled Y-axis option, drilling depth of 0-35 mm (with drill length GL 70 mm) is automatically set with driving overhang - Closed glue system with 6 bar glue pressure via glue nozzle, for glues with a viscosity of 150 to 350 mPas - Glue quantity continuously adjustable via operator software - GL/WATER selector switch for rinsing the glue system, 1 stainless steel container each for 5 kg glue and 5 l water - Control lamp for residual glue quantity display in the glue container - 1 side stop left, 1 side stop right and 1 center stop (all removable) - 4 start buttons for individual working with 1-4 workpieces - 4 pcs. Pneumatic inclined clamping cylinder 10° for workpiece thicknesses up to max. 80 mm, workpiece length (Y) min. 70 mm - 1 pc. suction funnel, connection Æ 80 mm - 1 pc. TCT control with: built-in industrial PC, incl. Soft PLC type Beckhoff TWINCAT, operating temperature range 0-50°C, TFT industrial display 15" resistive touchscreen, resolution 1024 x 768, CPU 2 GHz, 256 MB RAM, 2x network interface adapters, IDE hard disk, 4x USB rear, 1x USB front, operating system: WINDOWS 7 - programming via menu-driven user software, drilling distances freely programmable with ABSOLUTE, RELATIVE or GRID dimensioning, automatic workpiece mirroring and work step optimization, 4 work fields can be assigned with different programs, graphic workpiece display, parametric programming, 0-point shift, programmable work lists, error diagnosis with plain text OPTIONS: 1 electronic, optical glue monitoring system G.I.C. (Glue Insert Control) for 1 glue nozzle 4 vertical inclined clamping cylinders 10° with holder, additionally, (total 8 clamping cylinders) 1 surcharge for machine bed length 1800 mm with working length 1800 mm 1 surcharge for: 1 horizontal drilling unit, motor 1.5 kW, with multi-spindle drilling head with 3 individually controllable drilling spindles, pitch 32 mm arranged in X-axis, tool speed 3000 rpm. (The standard working length is not reduced) 1 Y-axis NC-controlled, with recirculating ball screw and dynamic traversing speed of 300 mm/sec. The dowel driving overhang 7-30 mm and the drill hole depth 0-42 mm can be programmed via software. (with drill length GL 77 mm) for vertical drilling unit drilling from TOP, Y-axis position 5-42 mm 1 surcharge Y-axis NC-controlled position 5-62 mm instead of 5-42 mm 1 surcharge for: 1 vertical drilling unit drilling from TOP, motor 1.5 kW, with multi-spindle drilling head with 3 individually accessible drilling spindles, 32 mm pitch arranged in X-axis, tool speed 3000 rpm. Y-axis position 5-42 mm, workpiece length (Y) min. 130 mm, (the standard working length is not reduced) 1 Z-axis NC-controlled, with K Chodpfx Aajxwaz Hjtsd

Condition: used, Year of construction: 1990, functionality: fully functional, machine/vehicle number: 254002, type of input current: three-phase, overall weight: 130 kg, input voltage: 380 V, number of spindles: 8, input frequency: 50 Hz, Schleicher frame dowel hole drilling machine DBH 600, Drilling motor 1.5 kW, 380 Volt, 50 Hz, Drilling stroke 0 - 130 mm, Special drilling gear with 3 rows and 8 spindles, 1 clamping cylinder, Special stop system for window frames and window mullions Weight approximately 130 kg Chedez Nkutepfx Aatjd as is, at the Seevetal location, excluding transport, EXW (Ex Works), subject to prior sale.

Condition: used, Year of construction: 2018, machine/vehicle number: 0-250-82-8302, input voltage: 400 V, input current: 29 A, input frequency: 50 Hz, controller manufacturer: HOMAG powerTouch / PC86, HOMAG DRILLTEQ V-500 / BHX 200/D – Year of manufacture: 2018 Vertical CNC machining center for drilling and milling operations. Equipped with dowel feeder and tool changer magazine, as shown in the inspection photos. Machine number: 0-250-82-8302 Chsdpfx Ao Agxfreatsd Control system: powerTouch / PC86, as shown in the screenshot Software: woodWOP 7.1, as shown in the screenshot from 22.10.2026 Meter readings according to the screenshot from 22.10.2026: Main usage: 2,885.92 h Total operation time: 6,789.99 h Photos of the meter readings and software are part of the image gallery. Electrical connection: 400 Y / 230 V, 3 phases, 50 Hz; neutral conductor required Maximum operating current: 29 A Fuse rating: 35 A Control voltage: 24 V Location: Basel area, Switzerland. Inspection possible until early December 2026 by appointment. Dismantling and removal will take place between December 8th and 18th, 2026, after coordinating a date. Price on request. Detailed spindle configuration, working areas, software/license scope, and delivery scope will be determined after consultation. Windows version still to be confirmed. Subject to change and errors.

Condition: not inspected (used), Year of construction: 2013, Bore diameter , mm Number of heads horizontal , St. Number of heads vertical , St. Götzinger Drilling and Milling Centre ----- For sale on behalf of a client! Machine for ‘left-hand’ and ‘right-hand’ parts. The machine was controlled via window-making software, but can also be operated via the machine’s own software. The machine is equipped as follows: Csdpfx Aasv N N Spetehd - Drilling units on the left and right for end-face drilling. - 3 units for drilling and milling for longitudinal machining. - Parts are loaded once and the unit carrier then moves to perform the various machining operations. Machine installation length approx. 6 m. For further information, see the attached PDFs.

Condition: like new (used), DEMONSTRATION MACHINE Chsdpexxi T Ujfx Aatjd For sale is a Felder FD-21 dowel boring machine. The machine is in use in our showroom and is therefore in mint condition. Technical data: - Version with 21 spindles - 2 hold-down clamps - 2 stops, each 1.5 m, for line boring - 2 side stops with reading optics - Indexing system for side stop with 8 positions - Motor power: 2 HP - Year of manufacture: 2025 The machine is located in A-5431 Kuchl and can be inspected and picked up during our opening hours at any time. Subject to prior sale! Related terms: dowel milling machine, drilling machine, line boring Reference: R-A0117

Condition: used, Year of construction: 2012, Dowel insertion machine Manufacturer: Weinig Chedps Ahpw Nefx Aatjd Type: UniPin 100 Year of manufacture: 2012 Technical data - Working width max. 260 mm - Workpiece thickness max. 150 mm - Number of insertion stations: 1 - Dowel diameter max. 8 mm - Dowel length max. 60 mm Note: The technical data and descriptions are copies of the original order confirmation. The information provided is for informational purposes only and is not binding.

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, machine/vehicle number: 1028 161, drilling depth: 75 mm, total width: 900 mm, total length: 1,200 mm, overall weight: 430 kg, spindle speed (max.): 2,800 rpm, drill spindle length: 800 mm, workpiece height (max.): 80 mm, number of spindles: 23, operating pressure: 6 bar, GANNOMAT COMBI 110 Dowel and multi-hole drilling machine Csdpfxozvm Hae Aatshd including stops READY FOR USE

Condition: used, Used dowel drilling machine Ayen Type DB 1000-B23 for drilling operations in the production of dowel joints in woodworking. The machine features a working width of 720 mm, a maximum clearance of 820 mm and different drilling depths for vertical and horizontal machining. Technical data: - Working width: 720 mm - Max. clearance: 820 mm - Drilling depth, vertical: 45 mm Cedpfx Aaozryr Uotohd - Drilling depth, horizontal: 120 mm

Condition: good (used), Year of construction: 1998, Ganner Universal Dowel Drilling Machine Universal dowel drilling machine for: Drilling carcass frames, hardware, and row of holes Chsdpfx Aoz Dt Hysatsd Drilling beam with 21 spindles Pitch 32 mm Guide rails for drilling rows of holes Angle stops Additional accessories Pneumatic pivoting of the drilling beam Working width 640 mm Portal passage approx. 750 mm Drilling stroke approx. 100 mm Position adjustment of the drilling unit 0-45 mm Position adjustment of the row of holes approx. 300 mm Motor 1.5 kW Technical data available upon request The data has been taken from a brochure, therefore no guarantee is given.

Condition: used, Dowel drilling machine, dowel drilling machine, drilling and dowel station, row of holes dowel drilling machine, knothole drilling machine, row drilling machine, drilling beam, multi-spindle drilling head, articulated multi-spindle head, row drilling machine, dowel drilling head, dowel drilling machine, drilling gear Chedpfx Ascuh D Rsated -Drive: 1.5 / 2.0 kW -Drill speed: 2200/4400 rpm -pneumatic workpiece clamping -15 drill bits from below, grid 32 mm -Bore head: swiveling -Foot switch -Bore depth: max. 185 mm -Height adjustment: max. Mm -Max. Clamping height: 110 mm -Dimensions: 950/1100 / H1350 mm -Weight: 616 kg

Condition: used, Year of construction: 2013, WEEKE OPTIMAT ABD 150, manufactured in 2013. CNC-controlled drilling, gluing, and dowel insertion machine for furniture components. Equipment: - 3 individually controlled vertical drilling spindles, spacing 32 mm - 3 individually controlled horizontal drilling spindles, spacing 32 mm - Gluing unit with adjustable glue quantity - Dowel insertion unit for standard dowels 8 x 30 mm / 8 x 35 mm - Automatic dowel feed via vibration feeder - 4 upper clamping cylinders - Left, right, and center workpiece stops - Automatic central oil lubrication - powerControl with woodWOP and ABDWork Codpfxo Afawbj Aatehd Workpiece range: Length 20–1,250 mm, width 100–800 mm, thickness 10–60 mm. The machine is located in the TEC-WOOD warehouse in Poland, approximately one hour from Frankfurt (Oder). The original photos show the machine in its previous location. Inspection, functional testing, and detailed information on the scope of delivery are available by appointment. Price on request. Offer includes free loading onto a truck. Transport is subject to separate agreement. High-quality machines sourced from Germany, Austria, or Switzerland. Consulting and sales handled by DS-Maschinen in Stuttgart. PC and software as shown in the original photos: woodWOP 6.1; Microsoft Windows XP Embedded, Version 2002, Service Pack 3; Beckhoff C9900-I374 v1.1. Counter photo: Total operating time 24,701.5 h, production time approx. 1,806 h. The values refer to different types of counters and the status of the available recording.

Condition: refurbished (used), Year of construction: 2014, Used Machine Year of manufacture: 2014 Condition: The machine has been factory-overhauled by Ganner Features and Technical Specifications: Complete standard configuration including: - Support with linear guide consisting of: 1 single-spindle horizontal drilling unit, 0.65 kW motor, 70 mm stroke Tool speed selectable via operator software (3000/5000/8000 rpm) 1 blow-out, gluing, and dowel-driving station for dowels Ø 8 mm, dowel length 25–50 mm - Fully automatic, electronically controlled central lubrication - X-axis NC-controlled, with working length 1300 mm, travel speed max. 105 m/min. - Z-axis manually adjustable via mechanical digital counter, position adjustable via support table 5–40 mm - Dowel drive-in overhang adjustable from 7–20 mm via a mechanical digital counter; drilling depth from 0–35 mm (for drill bit length GL 70 mm) is automatically adjusted with the drive-in overhang - Closed glue system with 6 bar glue pressure via glue nozzle, for glues with a viscosity of 150 to 350 mPas - Glue quantity continuously adjustable via operator software - GLUE/WATER selector switch for flushing the glue system, each with: 1 stainless steel tank for 7.5 kg of glue and 7.5 l of water - Indicator light showing remaining glue levels in the glue tank Chjdpjzlbrvofx Aatod - 1 left side stop, 1 right side stop, and 1 center stop (all removable) - 4 start buttons for individual processing of 1–4 workpieces - 4 pneumatic 10° angle clamping cylinders for workpiece thicknesses up to 80 mm, workpiece length (Y) min. 70 mm - 1 extraction funnel, connection Ø 80 mm - 1 TCT control unit with: Built-in industrial PC, including Beckhoff TWINCAT soft PLC, operating temperature range 0–50°C, 15-inch capacitive TFT industrial touchscreen, operating system: WINDOWS 7 - Programming via menu-driven user software, drilling distances freely programmable with ABSOLUTE, RELATIVE, or GRID dimensions, automatic workpiece mirroring and operation optimization, 4 work areas assignable to different programs, graphical workpiece display, parametric programming, zero-point offset, programmable worklists, error diagnosis with plain text Optional equipment: - 1 electronic, optical glue monitoring system G.I.C. (Glue Insert Control) for 1 glue nozzle - 1 Z-axis with NC-controlled, dynamic positioning for height adjustment of the drilling and dowel-driving station (programmable from 5–40 mm), travel speed max. 30 mm/sec. - 1 single-spindle vertical drilling unit drilling from the TOP, 0.65 kW, (3000/5000/8000 rpm), position (Y) manually adjustable via a mechanical digital counter from 5–40 mm, drilling depth (Z) max. 30 mm (with drill bit length GL 57 mm), Workpiece thickness (Z) max. 50 mm, workpiece length (Y) min. 130 mm (including drilling depth compensation, e.g., for Häfele Minifix) - 4 vertical 10° angle clamping cylinders with mount - 1 keypad with mount Availability: available shortly Location: DE-63934 Röllbach

Condition: used, Year of construction: 2007, functionality: fully functional, Machine for drilling holes for dowels URBAN DB 3100, year 2007 Condition: very good - Profile clamping system and drill feed operated by foot switch - Electric drilling motor switches off automatically at the end of the drilling process - Drill feed speed and drilling depth individually adjustable - Quick-clamp chuck for standard drill bits up to max. Ø13mm Csdpfx Ajwinq Njatehd - Left and right support tables

Condition: good (used), Year of construction: 2008, I sell the complete set of machines for production of wooden dowels. Year: 1993 - 2008 Brusa di Garboli TA30 L.Loser AA200 Moulders Cutting machines with feeders Cylinder sanding machines Totally 10 machines. Suitable for dowels 6-8-10-12-16mm. Very good condition. Chodst I U Amopfx Aatod Available immediately

Condition: used, Year of construction: 2005, Second-hand machine Year of manufacture: 2005 Features and technical specifications: - Motor: 400 V, 50 Hz, 3-phase, 1.5 kW - Pneumatic single-head drilling machine with 23 spindles - Aluminium ruler with 4 stops (2 profiles on the right/left, 1500 mm each) - with quick-action chuck - 2 patented, accident-proof pressure clamping cylinders - Connection for extraction system in accordance with EC standards - Aluminium drilling beam, spindle centre distance 32 mm - Work table made of MDF and cast iron - Patented spiral system for fine adjustment of the drilling depth - Pneumatic drilling head oscillation with Lockable in any position between 0° and 90° - Fold-down side stops with fine adjustment via counters with decimal display - Drilling height adjustment via dial gauges with decimal display - Back stop, travel up to 300 mm - Fixed stops 37 mm for fitting pot-type band drills - Complies with EC standards - Max. drilling width 704 mm Chodpfxszk N S Uo Aated - Max. drilling depth 65 mm - Max. workpiece width 960 mm - Max. workpiece length 3000 mm - Max. workpiece thickness 60 mm Availability: at short notice Storage location: 63934 Röllbach

Condition: used, Year of construction: 1984, Used Machine Year of Manufacture: 1984 Features and Technical Specifications: Universal dowel drilling machine with a swiveling drilling unit with fully automatic control with 2 safety pneumatic clamps Drilling gear motor: 2.2 kW with 21 spindles Spindle pitch: 32 mm with built-in oil damping Height adjustment: 80 mm Drilling depth: 80 mm Dimensions: 140x88x160 Weight: 420 kg Chjdpjzk Nuvjfx Aated

Condition: good (used), Year of construction: 2009, functionality: fully functional, Dowel Insertion Machine Ganner Selekta 252 Chjdpfxeycf Ike Aated Year of manufacture: 2009

Condition: ready for operation (used), Year of construction: 2003, Rilesa VLG 1524 3 drilling units from above 2 right/left aggregates Codju Shzfepfx Aatjhd

Condition: used, HIGH SPEED DOWEL CROSS-CUT AND CHAMFERING MACHINE LOSER MOD. AA220 - Range of working diameter: 6 - 18 mm - Capacity: about 7,500 - 15,000 dowels/hour Chodpfjqpdkcox Aatsd