Used Blow Moulding Machine for sale (65,320)

Condition: used, Stretch blow molding machine by Etek ISBM line = Injection stretch blow molding Stretch blow molding machine for single-use PET bottles made from PET preforms Stretch blow molding machine for production using the rotary process Manufacturer: ETEK / GF-Industries, Type Supra 800 sv 1 Credskucxlepfx Aiiji Serial number: 22000225 Year of manufacture: 2012 Power: 90 kW Mains connection: 400 volts, 50 Hz Weight: approximately 6000 kg In like-new condition

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Crodpsg Ailcsfx Aiiji Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, ID BYP01 We sell a used Chinese - PP melt-blown fabric extrusion line for melt blown, make: Zhangjiagang Sevenstars Machinery Co., Ltd., MFG 2020. It was used for a short time. excellent condition. All EU import duties have been paid. Output max 400 kg per 24 hours. General description: 1. Product size: PP melt blown fabric with width at 600mm (after trimming 17m*3) 2. Main Material: PP compounding material 3. Extruder type: SJ65/33 single screw extruder 4. Output capacity: 350-400kg/24hour 5. Electric power supply: 3phase, 380V; 50Hz 6. Additional equipment: • Vacuum feeder • Raw material dryer • Mesh manual filter • T-mould for melt blown fabric • Static electrical discharge equipment • Belt type forming 850mm • Collecting device • Winder and slitting Model L/D Output Speed of Screw Rotationl Power Center Height SJ-65 10-33 80-150kg/h 20-120r/min 18.5kw 1000mm This line contains the following machines: Automacic vacuum loader ZJ-400 and hopper dryer make RHONG model RDM-25, MFG 2020; Crsdpfxsuiq Dhs Aiisi Single screw extruder, model SJ65/33, MFG 2020; Heating oven for hot air, model HJGF101-4, MFG 2020; Extrusion T-mold, model: SUS630, made in Japan, MFG 2020; Forming device, MFG 2020; Winder & slitting system, MFG 2020; Oil free air compressor, MFG 2020; The PP melt blown nonwoven production line is a polymer melt extruded from a screw extruder. The polymer is extremely stretched by high-speed hot air or other means to form very fine short fibers, which are aggregated to A web is formed on a roller or a screen curtain, and is finally reinforced by self-adhesion or thermal bonding. Its unique properties are widely used in mask filter materials, thermal insulation filling materials, medical health materials, wiping materials, etc. The finished product can pass the N95 standard as the core material of the mask. Process of melt blown nonwoven production line Polymer preparation --- Melt extrusion --- Metering pump --- Melt blown die head assembly --- Solution thin-flow drawing --- Fibber cooling --- Auxiliary network --- Electrostatic electret --- Reinforced finished product. Melt-blown cloth is produced by melt-blown process. The equipment mainly includes: screw extruder, melt pump, screen changer, melt-blown device, winding device, air system (hot air blower and heater), etc. The function of the screw extruder is to melt the slice material; the role of the melt pump is to accurately measure, control the output and the fineness of the fiber, and continuously and evenly transfer the melt to the spinneret. The function of the screen changer is to filter out impurities in the melt so as not to block the spinneret holes. The function of the winding device is to pack the melt blown cloth into rolls. The function of the air system (hot air blower and heater) is to provide the temperature and pressure of the hot air used in the drawing of the spinning air stream. Price Euro 39.200 Euro + VAT, negotiable, FCA: Oradea / Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: good (used), Year of construction: 2017, functionality: fully functional, LINEAR PET BLOWING MACHINE SET with auxiliary equipment AC ARCOR - multiBlow2 - 2017 Speed: 1,5L - 6000 Cavities: 4 Formats: 0,1 - 3,0L AUXILARY EQUIP Crsdjquuvrepfx Aiiji 1. Chiller - M.T.A S.p.A - TAE EVO 051 2. LOW Pressure compressor - SHAMAL 45kw 3. Receiver tank - Low pressure - MAX 16Bar 4. Receiver tank - High pressure - MAX 45Bar

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 13-13, The BLOMAX 4 Blowmoulding machine is of the model 13-13. The machine has no defects and operates in excellent condition with full functionality. Csdpfx Aist Akgwjisri Power : 400V/150A/60000W Year of construction : 2000

Condition: used, Speed: 8.000 bph with 0,5 liter bottle. Different formats are possible optionaly. Dismanteling is made by Seegräber GmbH on begining februar 2018. List of machines included: -SIDEL SBO 6 Blowing machine. Completly overhault by SIDEL in 2006. -Preform magazin and preform elevator Crjdpe Ahk U Iofx Aiisi Compressor, cooling, moulds not included

Condition: excellent (used), Year of construction: 2014, operating hours: 54,738 h, functionality: fully functional, machine/vehicle number: 369A61525, screw diameter: 54 mm, overall weight: 9,000 kg, clamping force: 687 kN, total width: 1,850 mm, total length: 5,500 mm, total height: 3,200 mm, Equipment: documentation/manual, For sale: ASB Nissei 70-DPH, version 4 ISBM machine. Crsdo Ah H Dtopfx Aiiji Included with the machine is a Piován desiccant air dryer. The machine is powered on and can be inspected while running in a dry cycle.

Condition: good (used), Year of construction: 1998, operating hours: 89,340 h, functionality: fully functional, screw diameter: 90 mm, overall weight: 16,000 kg, clamping force: 650 kN, total width: 2,750 mm, total length: 5,600 mm, total height: 3,200 mm, Manufacturer: Sterling Model: 15 LBS Year of manufacture: 1998 Operating hours: 89,340 h Crjdpjzfxwiofx Aiioi Closing force: 650 kN Screw diameter: 90 mm BM Sterling APV, year of manufacture 1998 Complete control system replacement in 2008 with MACO-sys 6000, carried out by Davies-Standard LTD PRICE REDUCTION OF 30%!!! Net price: from 45,000 EUR to 31,500 EUR!!!

Condition: good (used), Year of construction: 1994, functionality: fully functional, Manufacturer: s.p.a magic m.p. Type: MGL2D This blow molding machine is in full working order. It is still in production and can be inspected after scheduling an appointment. Upon request, I can also send videos. Cedpfx Ajxxp Tbjiisri PRICE REDUCTION OF 30%! PRICE: REDUCED FROM 19,000 TO 13,300 EUR!

Condition: like new (used), overall weight: 850 kg, Year of construction: 2024, Cellulose fiber blowing machine AMEVAV01-VB, built by the owner in 2024. Approximately 10 tons of cellulose processed in total; low usage. Data according to the technical data sheet: declared capacity of 3,000 kg/hour with ISOGREEN cellulose fiber; three-phase 400 V, 50 Hz power supply; 3 kW gear motor; SC-7500 side-channel blower, 7.5 kW; maximum air flow 550 m³/hour; maximum overpressure 450 mbar; outlet Ø100 mm; declared weight 850 kg; length 232.8 cm and height 220 cm. Control panel with safety features and emergency stop. Technical data sheet and drawings available. Location: Bucharest, Romania. Price: 30,000 EUR excluding VAT, negotiable. Credpfo Ah E Ifex Aiiei

Condition: like new (used), Year of construction: 2022, operating hours: 200 h, functionality: fully functional, screw diameter: 70 mm, overall weight: 600 kg, clamping force: 80 kN, total width: 2,800 mm, total length: 4,000 mm, total height: 2,260 mm, Main Features: 1. Computer Control System (PLC) – Japanese Mitsubishi PLC 2. Electrical Cabinet – All electrical components are sourced from globally renowned brands, ensuring quality and stability. 3. Touch Screen – Innovation computer control system 4. Advanced Hydraulic Cylinder from Germany Cjdov Iflpspfx Aiisri 5. Linear Guideway 6. ABB Inverter from Switzerland & Rexroth from Germany 7. Large Diameter Galvanized Steel Pipes 8. Electric Lifting Platform 9. Ceramic Heater 10. Hydraulic System & Valve Connections – From Yuken Industry Technical Specifications: • Suitable Material: PE, PP, and others • Max Volume: 6 L • Production Capacity: 170-260 pcs/h • Dimensions: 4.0 × 2.26 × 2.8 m • Weight: 6T Plasticization System: • Reducer: Hard finishing, high strength, low noise • Screw: Ø 70 mm, L/D ratio 24, 38CrMoALA, cooling system available • Plasticization Capacity: 100 kg/h (HDPE) • Heating Zones: 3-4 aluminum heaters, automatic heating • Heating Power: 12 kW/h • Extruder Motor: Three-phase asynchronous motor (380V, 50HZ) • Cooling Fan: 4 zones, automatic cooling Extrusion System: • Material: High-grade alloy steel, central feeding • Number of Die Heads: 1 • Max Die Mouth Diameter: Ø 160 mm • Heating Zones: 4, stainless steel heating cycle • Heating Power: 5-7 kW Clamping System: • Features: High strength, rigidity, central mold locking, stable mold opening & closing • Clamping Force: 80KN • Template Distance Adjustment: 170-520 mm • Max Mold Size: 380 × 420 mm Electric System: • Automatic Monitoring, Fault Alarms, Auto Counting, Auxiliary Functions • Control Interface: Touchscreen with self-diagnosis alarm system • Temperature Control: Automatic temperature control module • Motion Control: Inovance (Chinese/English version) Hydraulic System: • Features: Multi-functional integrated hydraulic block, proportional control, high efficiency • Oil Pump Motor: Three-phase asynchronous motor (380V/220V, 50/60HZ) • Oil Pump: Imported double pump • Valves: Imported oil pump valves and connections • Oil Pipes: Double-layer wear-resistant • System Pressure: 60 kg/cm² • Cooling System: Separate water cooling cycle, oil cooler Pneumatic System: • Brand: Taiwan AIRTAC pneumatic system • Air Pressure: 0.6 MPa • Air Displacement: 0.8 m³/min • Electromagnetic Valve: Taiwan AIRTAC Main Components: Electronic Parts: • PLC Control System: MITSUBISHI from Japan • Touch Screen: INOVANCE • Temperature Controller: HUICHUAN • Auxiliary Relay: OMRON • Contactor: Schneider from France • Electric Motor: Three-phase 380V • Power Source: TAIWAN MEANWELL • Transducer: ABB from SWITZERLAND Hydraulic Parts: • Oil Pump: TAIWAN HIGH-TECH • Valve: YUKEN • Oil Pump and Connection: YUKEN • Sealed Part: HALLITE Air Control System: • Cylinder: AIRTAC • Air Valve: AIRTAC This blow molding injection machine was purchased directly from a factory in China for a specific project that was never realized. The machine was used for only one month. Location: Siemianowice Slaskie, Poland We also have peripheral equipment available for sale, such as: • 5 HP AIR COOLING SYSTEM • Auto Loading • 150 kg Color Mixer • Scraps Crusher

Condition: used, Year of construction: 2017, machine/vehicle number: SO149, Used KOSME KSB 6R rotary blow molding machine 12000 BPH - Year 2017Technical Specifications & Performance DataThis automatic rotary PET bottle blow molding machine is manufactured by KOSME and identified as model KSB 6R. Built in 2017, it is designed for forming PET bottles from preforms in industrial packaging and beverage production environments. The machine has a stated production capacity of up to 12,000 bph and was operated with six-cavity molds for the PCO 1881 neck finish.Manufacturer: KOSMEModel: KSB 6RYear: 2017Production capacity: 12,000 bphContainer material: PETMaximum bottle volume: 3.0LMold configuration: 6 cavitiesPreform neck type: PCO 1881Machine configuration: Automatic rotary blow molding machineAdvanced Automation & Control SystemsThe KOSME KSB 6R is an automatic rotary blower equipped with a preform feeding system. This arrangement supports a continuous supply of preforms to the blow molding process and is suited to integration within an automated PET bottling equipment layout. The rotary configuration is intended to support consistent bottle forming at the stated output rate.Machine-specific electrical data, control hardware and automation component specifications are not included among the available technical details. Installation and commissioning should therefore be planned around verification of the existing electrical interfaces, machine controls and safety circuits.Production Line Integration CapabilitiesDesigned for PET bottle production, this second hand blow molding machine can serve as the bottle-forming stage of a used bottling line. It is suitable for installations where PET containers are produced directly from preforms before downstream rinsing, filling, capping, labeling and secondary packaging operations.The included preform feeding system supports upstream preform handling. A chiller is available with the equipment and can support process cooling requirements. The compressor is not included, so a compatible compressed-air system is required for operation. The machine is configured for bottles up to 3.0L with PCO 1881 neck finish preforms.Machine Condition & Maintenance HistoryThe equipment was removed from operation in January 2026, dismantled and placed in storage. Its current condition is therefore classified as stored equipment. Operating hours are not provided. Buyers planning recommissioning should assess the condition of mechanical assemblies, pneumatic circuits, heating components, electrical systems and safety devices before installation.Operational Performance & VersatilityThis KOSME PET blow molding machine is intended for producing PET bottles used in beverage production and industrial packaging operations. Its six-cavity mold arrangement supported output of up to 12,000 bottles per hour. The documented configuration used PCO 1881 preforms, providing a defined neck-finish platform for compatible bottle and closure programs.Molds are excluded from the offer. Bottle design, final format and product application therefore depend on the... Cjdpfx Aj Aia Eweiiori

Condition: used, Year of construction: 1998, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 16/16 S1 Year of manufacture 1998 Capacity: 16,000 for 1.5 L bottles and up to 19,000 bph for 0.5 L bottles Installed power: 347 kW Includes 1.5 L moulds Preform feeder Chiller cooling unit Technical condition: used machine, functional until dismantled. The machine is currently dismantled, assembled in elements and prepared for transport. Crodpsutni Rjfx Aiiei Full and original technical documentation.

Year of construction: 2004, condition: used, Operating pressure: 210bar, injection unit force: 111kN, clamping force: 600kN, max. opening stroke: 340mm, mold installation height: 200-500mm, rated current, circuit 1: 29A, rated power, circuit 1: 15kW, supply voltage, circuit 2: 400V/50Hz, rated current, circuit 2: 66A, rated power, circuit 2: 46kW, AC control voltage: 230V, DC control voltage: 5/±15/24V, protection rating: IP54, weight: 6.63t, operating hours: 96,973h, with CE marking and documentation. Crodpfx Ais Ah Tyfjiji

Year of construction: 1990, condition: used, Clamping force: 250kN, operating voltage: 380V, heating power: 3.46kW, pump motor power: 7.5kW, total power: 11.3kW, weight: 1.5t, with documentation, has been serviced. Credj Ah Tyxopfx Aiiei

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, Equipment: documentation/manual, For sale: Complete PET bottle blowing line TES BluLine4 HiTech MultiFlex (2017) We offer for sale a complete PET bottle production line from the renowned manufacturer TES Sp. z o.o., model BluLine4 HiTech MultiFlex, manufactured in 2017. The machine is in very good technical condition, regularly used, and ready for further operation. Technical data Manufacturer: TES Sp. z o.o. Model: BluLine4 HiTech MultiFlex Year of manufacture: 2017 Bottle capacity range: 0.5 l – 4 l Number of cavities: 2-4 The line includes: Codjzd Sb Sopfx Aiijri ✅ Preform feeder ✅ PET bottle blowing machine ✅ Bottle packer for trays Advantages of the equipment Complete and ready-to-use production line Universal range of produced capacities Solid construction and proven TES technology Very good technical condition Ideal for manufacturers of beverages, water, household chemicals, and other products packaged in PET bottles Price: negotiable. If you have any questions or would like to obtain additional information, please contact us by phone or private message. We will gladly provide detailed information and send additional photos of the equipment.

Year of construction: 1996, condition: used, lamping force: 500kN, max. holding force: 37kN, mold protection force: 3-37kN, max. opening force: 37kN, max. increased opening force: 194kN, max. opening stroke (adjustable): 375mm, min. mold installation height: 250mm, max. distance between platens: 625mm, clear distance between tie bars: 320x320mm, platen dimensions: 490x490mm, max. ejector force: 38kN, max. ejector retraction force: 26.7kN, max. ejector stroke (hydraulic): 150mm, screw diameter: 25mm, screw L/D ratio: 20, max. screw stroke: 100mm, max. shot volume: 49cm³, max. nozzle contact force: 60kN, max. nozzle retraction stroke: 180mm, total installed power: 15.5kW, length: 4030mm, width: 1850mm, height (horizontal/vertical): 2000/3060mm, weight without oil: 3.06t, an on-site inspection is possible. Codpj Ah Tyiefx Aiijri

Condition: good (used), Year of construction: 2001, Ref. no.: 18092 Manufacturer: ENGEL Type: ES 1350H 200W / 300HL-2F Year of construction: 2001 Clamping unit Clamping force: 300 ton Opening stroke: 855 mm Platen size (h x v): 1050 x 650 mm Injection unit Screw diameter: 60 +35 mm Injection volume: 735 +135 cm³ Shot weight: 662 + 122 g Injection pressure: 1834 +1620 bar Measurements and weight Dimensions: 7,75 x 2,35 x 2,6 m Machine weight: 24780 kg Further information: ENGEL ES 1350H200W/300HL-2F — 2K Injection Moulding Machine This machine from the prestigious Austrian manufacturer ENGEL, built in 2001, features a clamping force of 300 tonnes and a true 2K L-configuration in horizontal layout. Motor and Hydraulic System Cedpfx Ajwm Iy Ejiieri The machine is equipped with a powerful electric motor coupled to a high-pressure hydraulic pump group. The electric motor continuously drives the hydraulic pump, providing pressurised oil flow throughout the entire system. This pressurised oil feeds the clamping cylinder, the injection pistons of both units, and the ejector system. The thick red hydraulic hoses visible behind Unit B carry this high-pressure oil flow — both units are supplied via independent hydraulic circuits, allowing Unit A and Unit B to operate simultaneously without influencing each other. Operating Principle The two independent injection units are positioned at 90° to each other — in an L-shape. The mould is locked with 300 tonnes of clamping force. Unit A injects the primary material into the mould at 1834 bar. Immediately afterwards, Unit B injects the second material or colour from a 90° angle into the same mould at 1620 bar. The two materials bond at a molecular level inside the mould, cooling is completed and the ejectors push out the finished 2K part as a single piece. No gluing, screwing or assembly is required — two materials emerge as one single part in a single cycle. Applications Automotive interior and exterior trim parts, large technical plastic components, parts combining a rigid body with a soft grip surface, two-colour large-surface parts.

Condition: used, Year of construction: 1996, functionality: fully functional, working width: 300 mm, planing height: 200 mm, High-performance planing and profiling machines / Four-sided planer Manufacturer: Weinig Type: Hydromat 30 / H 30 N The machine comes from a parquet manufacturing facility. Planing width: approx. 300 mm (according to the model designation) Planing height: approx. 120 mm (estimated) Spindle arrangement: Bottom (surfacing), 22 kW Right, 7.5 kW Left, 18 kW Top, 30 kW Cedpfx Aez D Exbsiiori Spindle diameter: 50 mm Feed rate adjustable, 12 - 120 m/min. Voltage: 380 V, 50 Hz Expected availability from January 2027!

Condition: ready for operation (used), Year of construction: 2005, operating hours: 60,000 h, functionality: fully functional, clamping force: 9,500 kN, screw diameter: 105 mm, clearance between the columns: 1,400 mm, displacement volume: 4,546 cm³, injection pressure: 1,778 bar, injection weight: 4,137 g, Clamping force 950 kN Mould opening force, max. 665 kN Travel force movable platen opening 112 kN Travel force movable platen closing 117 kN Size of mould platens (h x v) 1960 x 1710 mm Distance between tie bars (h x v) 1400 x 1150 mm Mould opening stroke 1800 mm Mould height min/max 600/1200 mm Max. daylight 2400 mm Injection unit: Screw diameter 105 mm Ls/D ratio 23 Injection pressure 1778 bar Stroke volume 4546 ccm Shot weight (PS) 4137 gr. Injection rate 805 ccm/s Screw speed 126 1/min Plasticising rate max. 147 g/s Nozzle pressure 166 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 110 kW Installed heating capacity 59 kW Adjustable barrel heating zones 7 Credpfx Aiox Hz I Neiei Reservoir capacity 1500 ltr. Dimensions and weights: Dimensions of the machine ca. 12,00 x 3,50 x 3,00 m Total machine weight 67000 kg Max. mould weight 20300 kg

Condition: good (used), Year of construction: 2005, Ref. no.: 16369 Manufacturer: BATTENFELD Type: EM 75-120 Unilog B4 All-electric Year of construction: 2005 Clamping unit Clamping force: 75 ton Opening stroke: 800 mm Distance between tie bars: 405 x 405 mm Mould height min.: 150 mm Mould height max.: 480 mm Injection unit Screw diameter: 18 mm Injection volume: 30 cm³ Shot weight: 27 g Injection pressure: 2440 bar Measurements and weight Dimensions: 4,5 x 1,7 x 2,0 m Machine weight: 4500 kg Further information: BATTENFELD EM 75/120 UNILOG B4 All-Electric Precision Injection Moulding Machine The BATTENFELD EM 75/120 UNILOG B4 is a high-quality Austrian-made all-electric injection moulding machine. The BATTENFELD EM series was considered one of the most advanced servo-electric machine concepts of its time and was specifically designed for energy-efficient and highly precise production processes. All major machine movements are driven by modern servo motors, providing: * very low energy consumption * high repeatability and precision * smooth and quiet machine operation * low maintenance requirements * stable and accurate production performance Crsdpfx Aewl Rucoiioi The machine is especially suitable for: * technical plastic components * electronic parts * precision moulded products * small and medium-sized production runs Compared to conventional hydraulic machines, the all-electric technology offers significantly improved energy efficiency and process stability. Equipped with the reliable BATTENFELD UNILOG B4 control system, the machine provides: * user-friendly operation * precise process control * stable cycle times * accurate servo axis management The machine has approximately 69,094 operating hours and appears to be in clean and well-maintained condition. The photos clearly show: * a clean electrical cabinet * well-maintained mechanical components * properly kept servo-electric units * a clean injection unit The BATTENFELD EM 75/120 UNILOG B4 is a reliable and energy-efficient solution for demanding plastic injection moulding applications.

Condition: repair required (used), Injection moulding machine, Engel ES 330/85, Used machine As shown in the pictures, its working condition is uncertain. Codpfoukn S Hsx Aiijri Overall dimensions :3100 x 1950 x 2600 mm Weight: 5500 kg Manufacturer: Engel Type: ES 330/85 Year of manufacture: 1997 Electrical data: 380V, 60 A, Contoller cards: Keba PS 244; Keba DO 321; Keba DO 321; Keba DO 321; Keba DI 325; Keba DI 325; Keba DI 325; Keba TT 081; Keba AR 181; Keba PD 242; Keba CU 211

Condition: good (used), Year of construction: 2003, functionality: fully functional, planing width: 230 mm, working height: 100 mm, Planer Moulder P 1000 UNIMAT STAR with 6 Tool Holders Cjdpfx Asxyu Itoiisri

Condition: ready for operation (used), Year of construction: 2006, operating hours: 30,000 h, functionality: fully functional, clamping force: 8,000 kN, screw diameter: 95 mm, displacement volume: 3,367 cm³, Clamping force 8000 kN Mould opening force, max. 560 kN Travel force movable platen opening 89 kN Travel force movable platen closing 92 kN Size of mould platens (h x v) 1600 x 1550 mm Distance between tie bars (h x v) 1120 x 1000 mm Mould opening stroke 1600 mm Mould height min/max 500/1100 mm Max. daylight 2100 mm Hydraulic ejector - stroke 300 mm Ejector force 200/100 kN Injection unit: Screw diameter 95 mm Ls/D ratio 23 Injection pressure 1795 bar Stroke volume 3367 ccm Shot weight (PS) 3064 gr. Injection rate 690 ccm/s Credpsymn Rvjfx Aiiji Screw speed 116 1/min Plasticising rate max. 104 g/s Nozzle pressure 166 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 53 kW Adjustable barrel heating zones 7 Oil Reservoir capacity 1500 ltr. Dimensions and weights: Dimensions of the machine ca. 11,00 x 3,00 x 2,60 m Total machine weight 44500 kg Max. mould weight 12200 kg Accessories: - Anti vibration pads Additional Options: - 1 x air valve - tiebar pull system - 3 x core pulls on movable plate - 2 x core pulls on fix plate - 20 x hot runner controller - Robot interface according to Euromap 67

Year of construction: 2007, condition: ready for operation (used), Various injection molding machines are available. 1) Arburg Allrounder 420 A 1000-400, clamping force: 100t, screw diameter: 30/35mm, year of manufacture: 2005. 2) Demag 1000-420-310 EL-Exis S, clamping force: 100t, screw diameter: 30mm, year of manufacture: 2003. 3) Demag 1000-420-200 EL-Exis S, clamping force: 100t, screw diameter: 25mm, year of manufacture: 2003. 4) Arburg 570 C 2000-150/60 2K, clamping force: 200t, screw diameter: 25/12+15mm, year of manufacture: 2007. 5) Arburg 420 C 1000-250, clamping force: 100t, screw diameter: 35mm, year of manufacture: 1996. 6) Arburg 420 C 1000-250, clamping force: 100t, screw diameter: 30/25mm, year of manufacture: 1995. 7) Arburg 420 C 1000-250, clamping force: 100t, screw diameter: 30mm, year of manufacture: 1994. 8) Netstal Synergy 600-110, clamping force: 60t, screw diameter: 25mm, year of manufacture: 2001. 9) Arburg 900T 800-150, clamping force: 80t, screw diameter: 25mm, year of manufacture: 2001. 10) 2 KM SilcoStar 922A, year of manufacture: 2007. On-site inspection is possible. Individual sale possible. Some machines are partially dismantled and/or defective. Credpfxswkiico Aiioi