With cooling unit and compressor
Capacity: 2000-2500 bph
Bottle: 0,5 l
Bokq393pri
ADS G66C blow molding machine
Capacity: 8,000 bottles / h
Btkgldqwbw
Number of slots: 6
Year of production: 1997
Machine with air recovery
Form: 1.5 liters
Number of hours worked: 33,408 h
Included:
- preform basket tipper
- preform feeder
- 800 l air tank
- sterilizing filter
- preform chiller MTA year 2003
The machine is in very good condition, regularly serviced, the machine can be checked in a dry mode.
The injection blow molding machine VICTOR MACHINERY MSZ 30 for the production of bottles was built in 2015.
Technical parameters :
- screw diameter: 40 mm
- screw L / D: 22: 1
- injection weight (HDPE): 190 g
- maximum speed of the screw: 10-225 rpm.
- heating power: 8.3 kW
- injection clamping force: 292 kN
- blow clamping force: 46.7 kN
- maximum plate size (L x W): 400 × 270 mm
- minimum mold thickness (H): 180 mm
- mold heating capacity: 3 kW
- opening: 220 mm
- drying cycle: 3.5 sec.
- eng...
Semiautomatic PET Bottle Blow Molding Machine PV-30 is an two-step bottle stretch blowing machine. It has 1 cavity and the capacity range of the products is from 19.0 L to 30.0 L PETor PET KEG, barrels and cans with productivity up to 40 b/h
Be2lvzphfl
Output: 280kg/h, clamping force: 400kN, installation height: 500mm, opening stroke: 900mm, dimensions clamping plates: 700x830mm, drive power: 129kW, heat output: 43.1kW, connected load: 172.1kW, operational hours: 70,000h, with partial wall thickness distribution control PWDS.
Ssojrg
Automatic PET Bottle Blow Molding Machine A-3000-4 is an automatic two-step bottle stretch blowing machine. It has 3 cavities and the capacity range of the products is from 0.25L to 2.2 L with productivity up to 4 000 bottles (1.0L) in hour.
Vc2buji
Brand: LOG MACHINE
Shot weight: 298 g
Jb9slc9dc
Screw diameter: 45 mm
Clamping force: 160 ton
Opening stroke: 430 mm
Distance between tie bars: 460x460 mm
Mold thickness: 180-500 mm
ARBURG 630S 2750-800/290 2K machine / production line with Wittmann W823 robot, rotary table, 2 conveyor belts and protective housing
Year of manufacture: 2015
Injection unit:
Screw diameter: 45 mm
Injection weight: 291 g
Injection pressure: 2470 bar
Dosing volume: 318 ccm
clamping unit :
clamping force: 275 t
tie bar distance: 630x630 mm
size of clamping platens: 900x900 mm
ejector: hydraulic
clamping unit: hydraulic
control system:
SELOGICA - touch control panel
Additional equipment:
Productio...
screw size:45 mm
Kaieoz
injection shot weight in Polysterol:149 g/PS
closing pressure:100 kN
1,0 St. gebr. Spritzgießmaschine
Hersteller: DEMAG
Zr8sesy
Typ: Ergotech80/420-310System
Baujahr: 2000
Schließkraft: 80 Tonnen
Schnecken DN: 35 mm
Spritzteilgewicht: 151 g / PS
Steuerung: NC4
Ausstattung:
1 x Kernzug
Schnittstelle Roboter
Mit Motan Aufsatztrockener
screw size:100 mm
injection shot weight in Polysterol:3.574 g
clamping force:13.000 kN
INJECTION UNIT:9200
screw size:100 mm
max. swept volumne:3.927 cm³
injection shot weight in Polysterol:3.574 g/PS
injection pressure:2.352 bar
CLAMPING UNIT:.
closing pressure:1.300 t
tie bar distance:1.600 x 1.250 mm
mould hight - min.:650 mm
mould hight - max.:1.400 mm
opening stroke:2.430 mm
CONTROL:.
microprocessor control:Unilog B4
screen text:deutsch / german
Manual:deutsch / german
EQUIPMENT:.
ro...
screw size:30 mm
injection shot weight in Polysterol:65 g/PS
closing pressure:400 kN
daylight:270 x 270 mm
opening stroke:350 mm
mould height - Max./min.:200 mm
Bdwqo9ro3s
control:Selogica (1. Version)
daylight between platens - max.:550 mm
total power requirement:21 kW
dimensions of the machine ca.:4,30x1,60x2,08 m
few operation hours - condition like new -
- wear reisistant plastification unit
- fully hydraulic clamping unit
- with Vario system
- mould blow unit
- sorter unit
- interface ...
Screw diameter: 30 mm
Screw speed: 20-300 r/m
Max stroke volume: 99 cm3
Max shot weight: 114 g
Closing force: 45 t
Opening path: 200 mm
Ejector force: 2t
Ejector path: 20 mm
Mold installation height min.: 264 mm
Plate spacing max.: 464 mm
Buzceyznkg
Platten size: 860x320 mm
ARBURG 630S 2500-1300/350 / two-component machine
Year of manufacture: 2003
injection unit:
Screw diameter: 70 mm
injection weight: 826 g
Injection pressure: 1470 bar
Dosing volume: 904 ccm
clamping unit :
clamping force: 250 t
tie bar distance: 630x630 mm
size of clamping platens: 900x900 mm
ejector: hydraulic
clamping unit: hydraulic
Control system: SELOGICA
Additional equipment:
Euromap
Robot interface
Hydraulic core pull x 1
Control with hot runners x 12
Proportional valve on both injection ...
screw size 28 mm
injection shot weight in Polysterol 62 g/PS
closing pressure 500 kN
Control T2
stroke 350 mm
ejector stroke 80 mm
clamping plate 500x500 mm
worm stroke 120 mm
Drive 11 kW
total power requirement 19,29 kW
weight of the machine ca. 2,0 t
Hpxpwie
dimensions of the machine ca. 3,2x1,1x1,8 m
Hersteller: ARBURG
Typ: 320C500-100
Baujahr: 2002
Schließkraft: 50 Tonnen
Schnecken DN: 30 mm
Spritzteilgewicht: 36 g / PS
Steuerung: SELOGICA
Bwy2d9gg0s
Ausstattung:
1 x Kernzug
Schnecke Hochverschleißfest
Euromap 32 - polig
Zylindereinheit bis 450° C
Anschluss Selektiereinheit
Technical parameters :
- control: UNILOG 4000
- clamping force: 75 tons
- opening force: 53 kN
- external panel size: 640 x 640 mm
- spacing between columns: 404 x 404 mm
- column diameter: 65 mm
- min. mold height: 250 mm
- column spacing: 400 mm x 304 mm
Frexh9c
- plate size: 640 mm x 540 mm
- mold opening stroke: 375 mm
- max. mold opening: 625 mm
- ejector force: 17.5 kN
- ejector stroke: 160 mm
- dry cycle: 32 1 / min.
- screw: 35 mm
- screw stroke: 140 mm
- screw speed: 0-275 min.
- nozzle...
screw size 40 mm
injection shot weight in Polysterol 182 g/PS
closing pressure 950 kN
mould height - Max./min. 250 - 725 mm
opening stroke 475 mm
tool clamping area 640 x 640 mm
420 x 420 mm
Dimensions (L/W/H) 4,3x1,4x2,0 m mm
total power requirement 27,5 kW
weight of the machine ca. t
dimensions of the machine ca. m
CNC Injection Moulding Machine Unilog 4000 Control
with core drawing
with belt convoyer, HB Therm 80°
drying air drier
Oipksj88c
Clamping force: 1000 ton
Opening force: 40 ton
Mold opening path: 1900 mm
Clear axial distance h x h: 1550 x 1200 mm
Clamping plate distance: 2000x1605 mm
Bvklllmuko
Ejector force: 200 kN
Ejector stroke: 300 mm
Screw diameter: 90 mm
Injection pressure: 2300 bar
Injection volume: 2799 cm3
Shot weight: 2407 g
Control MOSAIC
Core pulls 2 + 2 NG10
Daylight between platens max 1.900 mm
Dimensions (long x wide x high) 11.800 x 3.300 x 2.600 mm
ARBURG 520C 2000-675 with robot Wittmann W818 / machine in very good technical condition
Year of manufacture: 2002
injection unit:
screw diameter: 45 mm
injection weight: 240 g
Injection pressure: 2500 bar
Dosing volume: 286 ccm
clamping unit :
clamping force: 200 t
tie bar distance: 520x520 mm
size of clamping platens: 685x685 mm
ejector: hydraulic
clamping unit: hydraulic
control system:
SELOGICA
Svbhbw
Additional equipment:
Euromap 67
Euromap 12
Robot interface
Hydraulic core pull x 1
Injecti...
candle diameter: 21 mm
candle length: 300 mm
capacity: 1872 Stück/h
heating-up temprerature: 70-120 °C
cycle time: 13 sec
candle material: Paraffin/Stearin
control: Siemens S 5
space requirement of the machine approx.: ca.L:24 xB: 2 xH: 5,2 m
Candle Production Plant / Candle Molding Machine
- This plant is applied for the production of parafin/stearin candles according to the casting process with a high degree of automation.
- Multicoloured candles can be produced and equipped with various mou...
1,0 St. gebr. Spritzgießmaschine
Hersteller: ARBURG
Typ: 320C600-100
Bwy08trbsa
Baujahr: 2003
Schließkraft: 60 Tonnen
Schnecken DN: 25 mm
Spritzteilgewicht: 44 g / PS
Steuerung: SELOGICA
Ausstattung:
1 x Kernzug
Integralangußpicker
Förderband im Maschinenbett
Technical data :
- CNC control: UNILOG 4000 B
- maximum clamping force: 50 tons, 500 kN
- opening force: 40 kN
- meter reading: 9852,8 h
- maximum injection volume: 99 cm3
- maximum injection pressure: 2022 bar
- maximum processing temperature: 450 degrees C
- auger: 30 mm
- plasticizing capacity: 10.5 g / sec.
- screw stroke: 140 mm
- screw speed: 0-290 min.
- nozzle stroke: 200 mm
- heating power of heaters: 7.88 kW
- external panel size: 480 x 480 mm
- spacing between columns: 304 x 304 mm
- ...
screw size:55 mm
injection shot weight in Polysterol:390 g/PS
closing pressure:1600 kN
daylight:520 x 520 mm
opening stroke:max. 650 mm
mould height - Max./min.:250 mm
control:Selogica
daylight between platens - max.:max. 900 mm
total power requirement:46,3 kW
weight of the machine ca.:6,7 t
dimensions of the machine ca.:5,40x2,00 x 2,20 m m
CS version IV
- LCD control monitor, colour type
- technology step 2, - servoregulated with 2 regulating pumps
- with Selogica-control
- highly wear re...
ENGEL electric EMAX 200/100
Clamping force: 100 ton
Screw diameter: 25mm
Bwpyga2a8l
ARBURG 520C 2000-675 with robot Wittmann W430
Year of manufacture: 1998
injection unit:
screw diameter: 45 mm
injection weight: 240 g
Injection pressure: 2500 bar
Dosing volume: 286 ccm
clamping unit :
clamping force: 200 t
tie bar distance: 520x520 mm
size of clamping platens: 685x685 mm
ejector: hydraulic
clamping unit: hydraulic
Control system: SELOGICA
Additional equipment:
Euromap
Robot interface
Air valve x1
Hydraulic core pull x2
injection unit hardened - bimetal
The machine is equipped w...
Used machine in good condition. Available for immediate delivery.
- Clamping force: 1.400 kN
- Screw diameter: 40 mm
- Injection pressure: 2.100 bar
- Injection volume: 220 cm³
Bv2mob8rpo
- Screw L/D ratio: 20
- Mould opening stroke max: 500 mm
- Mould height max: 480 mm
- Mould height min: 240 mm
- Daylight between platens max: 980 mm
- Platen size (h x v): 650 x 650 mm
- Distance between tie-bars (h x v): 430 x 430 mm
- Core pulls: 1
- Power: installed max: 18,5 + 9,60 kW
- Weight: 6.800 kg
...
1,0 St. gebr. Spritzgießmaschine
Hersteller: ARBURG
Typ: 270S350-60
Bwyz7q8rcr
Baujahr: 1998
Schließkraft: 35 Tonnen
Schneckendurchmesser: 25 mm
Spritzteilgewicht: 36 g / PS
Steuerung: SELOGICA
Ausstattung:
1 x Kernzug
Angußpicker Hersteller: Eigenbau
Injection ENGEL ES 330/80 HL ST built in 1997 in Austria.
Technical parameters :
- CNC control: EC88
Injection elements:
- screw diameter: 35 mm
- injection weight: 140 g
- injection pressure: 1600 bar
- injection volume: 154 ccm
Closure components:
- closing force: 80 t
Encx0dz
- table top dimensions, max .: 730 x 600 mm
- ejector: hydraulic
- closing system: hydraulic (tie-bar-less)
Dimensions:
- weight: approx. 6000 kg
- dimensions of the machine (length x width x height): 3.91 x 1.38 x 2...
Machine type: Km 4000 MCz
Weight: 272,000 kg
SPRING UNIT:
Screw diameter: 1st unit 140 mm; 2nd unit 95 mm.
injection weight: 1st unit 8825 g; 2nd unit 2690 g
Clamping force: 40,000 kN
Stroke volume: 1st aggregate 9698 cm³; 2nd aggregate 2956 cm³
injection pressure: 1st unit 1960 bar; 2nd unit 1931 bar
CLAMPING UNIT:
Clamping force: 4,000 tons
Mould opening force: 290 tons
clear width H x V: 2,240 x 1,800 mm
max. opening stroke: 5,200 mm
max. mould opening stroke: 4,100 mm
mould installation heig...
screw size 60 mm
injection shot weight in Polysterol 380 g/PS
closing pressure 1600 kN
mould height - Max./min. 300-850 mm
tool clamping area 700x700 mm
450x450 mm
total power requirement 45 kW
weight of the machine ca. 5,7 t
dimensions of the machine ca. 5,5x1,3x2,9 m
Bfqbyse2o8
Serial No: 300137
ARBURG 470C 1500-150/150 / 2K machine / machine in very good technical condition
year of manufacture: 2005
injection unit:
screw diameter: 25 mm
injection weight: 49 g
Injection pressure: 2500 bar
Dosing volume: 54 ccm
clamping unit :
clamping force: 150 t
tie bar distance: 470x470 mm
size of clamping platens: 685x685 mm
ejector: hydraulic
clamping unit: hydraulic
Control system: SELOGICA
Additional equipment:
2K machine
Euromap 67
Robot interface
Air valve x1
Hydraulic core pull x 1
Injection u...
including Robot and hopper dryer +loader
- Screw diameter: 22 mm
- Shot weight max: 35 g
- Injection rate: 78 cm³/s
- Injection pressure: 2.060 bar
- Injection volume: 38 cm³
- Screw speed: 360 rpm
- Screw L/D ratio: 18,7
- Nozzle stroke / force max.: 28 mm / kN
- Nozzle stroke max: 200 mm
- Clamping force: 500 kN
- Mould opening stroke max: 600 mm
- Mould height min: 200 mm
- Heating zones: 4
- Platen size (h x v): 500 x 350 mm
Bvrqe3szwf
- Ejector force: 40 kN
- Control: CC200
- Oil tank ca...
1,0 St. gebr. Spritzgießmaschine
Gsrjlqgo
Hersteller: ARBURG
Typ: 270S350-60
Baujahr: 1998
Schließkraft: 35 Tonnen
Schneckendurchmesser: 25 mm
Spritzteilgewicht: 36 g / PS
Steuerung: SELOGICA
Ausstattung:
1 x Kernzug
Angußpicker Hersteller: Eigenbau
Injection molding machine SANDRETTO MODULA 270/1372 MACH 2 produced in 1999 in Italy.
Technical data :
- machine version: HP - High Pressure
- injection volume: 665 cm3
- clamping force: 2650 kN
- initial opening force: 530 kN
Ddltbtf
- column spacing: 570 x 570 mm
- screw diameter: 60 mm
- length, width, height: 8.40 x 1.80 x 2.38 m
- machine weight: 10,300 kg
screw size:*** mm
injection shot weight in Polysterol:*** g/PS
Buc2okkbnp
closing pressure:1100 kN
Screw diameter 25 mm interface for sprue picker,
printer interface
ready for use good condition ,no shift operation
with( additional control probably disk drive defective)
Injection unit new sealed.
Xeyq97v
ARBURG 470C 1500-800 / machine in very good technical condition
Year of manufacture: 2004
injection unit:
screw diameter: 50 mm
injection weight: 359 g
Injection pressure: 2000 bar
Dosing volume: 392 ccm
clamping unit :
clamping force: 150 t
tie bar distance: 470x470 mm
size of clamping platens: 650x650 mm
ejector: hydraulic
clamping unit: hydraulic
Control system: SELOGICA
Bw70px8wrk
Additional equipment:
Hybrid machine: energy saving, high speed and very quiet.
Hydraulic core pull controlled b...
including Robot and hopper dryer +loader
Bvrqfzgksi
- Screw diameter: 22 mm
- Clamping force: 1.000 kN
- Shot weight max: 42 g
- Injection rate: 157 cm³/s
- Injection pressure: 2.400 bar
- Injection volume: 46 cm³
- Screw speed: 400 rpm
- Screw L/D ratio: 24,8
- Nozzle stroke / force max.: 225 / 28 mm / kN
- Nozzle stroke max: 225 mm
- Mould opening stroke max: 350 mm
- Mould height max: 450 mm
- Mould height min: 150 mm
- Daylight between platens max: 800 mm
- Platen size (h x v): 650 x 600 mm...
1,0 St. gebr. Spritzgießmaschine
Hersteller: KRAUSS MAFFEI
Typ: KM80-520C1
Baujahr: 2001
Schließkraft: 80 Tonnen
Bwwhnk8arw
Holmabstand h x v: 405 x 405 mm
Öffnungsweg max: 750 mm
Schneckendurchmesser: 40 mm
Schussgewicht in PP: 156 g
Steuerung: MC4
Ausstattung:
Kernzug pneumatisch 1 x FAP
Kernzug hydraulisch 1 x BAP
6 Heißkanalregelstellen
Plastic injection molding machine TOYO MACHINERY SI-130-6 was built in 2016. The injection molding machine has 127 tons of short circuit and 266cc injection. The installed control enables the machine to work with many injection molds.
Technical data of the injection molding machine:
- clamping force: 127 tons
- man-hours: 15554 h
- injection capacity: 266 cm3
- minimum mold height: 150 mm
- maximum height of the mold: 550 mm
- clearance between tables: 950 mm
- maximum opening with minimum mold...
Offer-Details:
Bws7tp9t0v
Stock-No. 13147
Manufacturer Krauss Maffei
Type of machine KM 800 – 6100 MX
Year 2006
Working hours 68000 h
Controlversion MC 5
Screentext German
Location Eschweiler - Germany
Clamping unit:
Clamping force 8000 kN
Mould opening force, max. 560 kN
Travel force movable platen opening 89 kN
Travel force movable platen closing 92 kN
Size of mould platens (h x v) 1600 x 1530 mm
Distance between tie bars (h x v) 1120 x 1000 mm
Mould opening stroke 1600 mm
Mould height min...
screw size 50 mm
injection shot weight in Polysterol 200 g/PS
closing pressure 950 kN
mould height - Max./min. 250-700 mm
tool clamping area 590x590 mm
380x380 mm
total power requirement 33,2 kW
weight of the machine ca. 4 t
dimensions of the machine ca. 4,3x1,4 m
Bfqby2wbc9
Serial No: 330077
ARBURG 420S 1300-350 with robot Wittmann W818
Year of manufacture: 2000
injection unit:
Screw diameter: 45 mm
injection weight: 194 g
Injection pressure: 1670 bar
Dosing volume: 230 ccm
clamping unit :
clamping force: 130 t
tie bar distance: 420x420 mm
size of clamping platens: 650x650 mm
ejector: hydraulic
clamping unit: hydraulic
control system:
SELOGICA
Additional equipment:
Euromap 67
Euromap 12
Robot interface
Air valve x 1
Hydraulic core pull x 1
Injection unit hardened - bimetal
Proportio...
Used machine in good condition. Available for immediate delivery.
- Screw diameter: 75 mm
- Shot weight max: 1.640 g
- Injection volume: 1.725 cm³
- Clamping force: 3.800 kN
- Daylight between platens max: 700 mm
- Platen size (h x v): 1.025 x 945 mm
- Dimensions (long x wide x high): 8.400 x 2.000 x 2.700 mm
Ogluthu
- Weight: 19.000 kg
1,0 St. gebr. Spritzgießmaschine
Hersteller: KRAUSS MAFFEI
Typ: KM150-700C1
Baujahr: 2001
Schließkraft: 150 Tonnen
Holmabstand h x v: 500 x 500 mm
Öffnungsweg max: 800 mm
Schneckendurchmesser: 50 mm
Schussgewicht in PP: 311 g
Steuerung: MC4
Jw7eze
Ausstattung:
Kernzug pneumatisch 1 x FAP
Kernzug hydraulisch 2 x BAP
12 Heißkanalregelstellen