Used Bellow for sale (185)

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for Iiedpfxsuxfu Nj Aa Esd non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Year of construction: 2015, condition: used, workpiece diameter 300 mm workpiece weight 999 kg workpiece height 145 mm Features: -Digital display vertical axis -Automatic feed -Programmable automatic end stop -Grinding spindle drive with infinitely variable electronic speed control -Infinitely variable cross feed and table rotation -24V magnetic clamping plate 300 mm -Various occupational safety devices, e.g. protective cover monitoring, operating status display via traffic light -Lubricating oil level monitoring -The machine was completely overhauled in 2015, at which time the entire electrical system was replaced with PLC control and 24V control voltage -Paper belt filter system specially designed for this machine The following work has now been carried out: -Replacement of bellows and belts -New bearings for grinding spindle -Grinding carriage bed and rotary table bed scraped by hand to restore better and more precise running characteristics -Grinding carriage and cross table lifted from machine body and all tracks Isdpfexflclex Aa Esid cleaned, lubrication checked -Various wear parts, such as rubber caps and switching elements, replaced -Detailed functional check -Modernisation of feed arm -Paint touch-up work, machine colour: light grey RAL 7035 and RAL 7012

Condition: used, maximum load weight: 28,070 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 08/2020, next inspection (TÜV): 03/2027, loading space volume: 92 m³, total width: 2,550 mm, total height: 4,000 mm, Equipment: ABS, Knapen Walking Floor K100 92m³ 10mm Floor New TÜV, brakes, air bellows, etc. replaced General Info • Manufacturer: Knapen Trailers • Model/Type: K100 A5060 • Year of manufacture: 2020 • Chassis number: XPNK0C100LD071956 202003-0071956-r_order-configur? • Country of registration: Germany • Unladen weight: approx. 7,924 kg 202003-0071956-r_order-configur? • Gross vehicle weight: 36,000 kg 202003-0071956-r_order-configur? Iisdpfsyxa Ekjx Aa Ejd • Max. axle load: 24,000 kg • Max. king pin load: 12,000 kg (permitted in country of registration) • Volume: approx. 91.9 m³ • Tapered walking floor trailer • Axle design: rigid?rigid?rigid --- Dimensions • External length: 13,670 mm • External width: 2,550 mm • External height: 4,000 mm • Internal height front: 2,690 mm • Internal height rear: 2,785 mm • Fifth wheel height: 1,150 mm • King pin to 2nd axle: 7,750 mm • Axle distance 1st-2nd axle: 1,310 mm • Axle distance 2nd-3rd axle: 1,310 mm --- Axles & Chassis • 3 x SAF 9 t Intradisc+ Integral CD Off-Road axles • All axles rigid • Disc brakes Ø 430 mm • 10-hole wheel connection • Air suspension with standard control panel left in front of axles • Lift axle, fully automatic via EBS • Start assist included (3x braking) • Radio remote control for lift axle --- Tyres & Rims • Goodyear KMAX T • Tyre size: 385/65 R22.5 • Steel rims 22.5" x 11.75 • 6 wheels total • No spare wheel --- Body • Closed side walls left and right • Moving partition wall (min. ground clearance 100 mm) • Rear doors with external locking bars • One locking bar per door • Upper steel belts, left and right swiveling • Platform at front wall • Ladder on front wall left and right • Standard roof bows Ø 60.3 mm (4 units) • Bow storage: 3 x approx. 4,100 mm • Tarp 680 g/m² (RAL 9006 White Aluminum) • Tarp supports 3-position (4 units) • Lashing straps (4 units) --- Floor / Walking Floor • Cargofloor system CF-500 SL-C • Electric control • Ribbed aluminium floor boards 10 mm (21 boards) • Fixed front plate • Stainless steel plate at rear under floor --- Attachments • JOST landing legs with stroke equalization • Plastic toolbox left in front of axles (1000 x 500 x 500 mm) • 30 l water tank with soap dispenser • Closed side underrun protection • Swiveling mud flaps • Anti-spray mat on 3rd axle • Long stairway with extendable rear steps and platform • 2 x wheel chocks left • Broom and shovel holder right --- Lighting • 6 x round LED taillights (3-chamber) • LED fog and reversing lights • LED side marker lights (4 pairs) • LED marker lights at rear • Reflective contour markings according to EU regulations • LED work lights at rear (remote controlled) • LED work lights at landing legs (remote controlled) • LED LCG-2 switch unit --- Hydraulics/Connections • ISO-N and ISO-S connectors + 15-pin socket • Knapen Trailers V1 radio remote control • Hydraulic connections centrally at front wall (vertical) • Pressure line left, return line right • Additional hydraulic connections at landing legs • Brake connections present • Acoustic reversing signal (manually adjustable) --- Paintwork • Superstructure in RAL 7011 Iron Grey • Wheel hubs in RAL 2008 Bright Red Orange • Chassis and underside unpainted For further information, please feel free to contact me.

Condition: used, Year of construction: 1972, functionality: fully functional, machine/vehicle number: 1307-62, total height: 1,600 mm, total length: 1,360 mm, total width: 610 mm, grinding wheel diameter: 175 mm, overall weight: 670 kg, grinding length: 500 mm, grinding spindle speed: 4,350 rpm, travel distance X-axis: 500 mm, travel distance Y-axis: 225 mm, travel distance Z-axis: 230 mm, grinding spindle motor power: 550 W, table length: 800 mm, table width: 165 mm, power: 0.55 kW (0.75 HP), disc diameter: 175 mm, Semi-automatic tool grinding machine with infinitely variable table drive. Machine inspected, grinding motor newly fitted with bearings. Grinding spindle of newer design without disturbing noises (repairable). Bellows in good condition, cross bellow new. Clamping surface undamaged. Electrical system inspected. For further details, see operating manual. Iiodsytq Abepfx Aa Ejd

Condition: new, functionality: fully functional, New, fully functional Leybold/VAT Leycon HV gate valve with bellows 6528450 for sale from old stock, with a 6-month warranty. Iedpfjyrr Shsx Aa Ejid Worldwide shipping available – request a quote! If you are looking for a vacuum pump, accessories, or any vacuum technology-related equipment, please contact us. We are happy to assist you with purchasing, technical advice, or developing custom solutions.

Condition: used, Vacuum lifting device, vacuum lifter RIVATEC UNIGRIPPER Custom-made as a handling device for an industrial robot Year of manufacture: approx. 2008 Load capacity: approx. 50 kg - 7 suction pads Ø 32 mm (design allows for 12) Iedpfx Ajwywipea Ejid - 16 suction pads Ø 42 mm (design allows for 20) - 5 suction pads Ø 60 mm (design allows for 6) - a few suction cups missing, see photos (bellows suction pads) - swiveling base body for suction surface at 90° angle or flat 180° - base body pneumatically swiveling - Very elaborate and precise construction with linear guides - Flange plate for suspension or attachment to the robot - Equipped with many Festo components Required space (L x W x H): 620 x 300 x 300 mm Net weight: 28 kg Good condition 2 units available, price indicated per unit

Year of construction: 2022, condition: new, machine/vehicle number: 82002022104, ZIM 1025 PLUS Block and Paverstone Machine is special design machine for block and interlock production that works fully automatic.The movement of the machine is programmed the PLC microprocessor computer. By changing moulds all kinds of blocks, paverstones, curbstones, grass stones, lentos and precast concrete elements can be produced in a serial way. 20cm block can be produced 10, interlock paverstones can be produced 25 units in one press. Machine is able to produce the insulated block upon demand. Thanks to special features developed by our engineers machine have very short cycle time. For example mould changing is wery easy and take short tme in new system. Automation system and operator panel which is developed and redesigned in long years become user friendly and useful. Iedpfxoifz Aho Aa Ejid With our special design vibration table you can produce high quality products with less energy. We use pneumatic bellows in machine mould connections, due to this system vibration on mould is expanded regular and uniform. Service and maintenance is easy thank to our strong machine chassis and ergonomic design

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Universal Milling Machine Deckel FP4M with 3-Axis Heidenhain Digital Readout, Special Paint Finish in Light Grey, CE Compliant!!! Technical Specifications: - Year of manufacture: 1987 Machine no.: 2203-2790 - Rigid angle table (freshly planed) - Spindle speed: 50–2500 rpm - Feed rate: 8–630 mm/min - Drive power: 3.7 / 4.4 kW - Spindle brake - Rapid traverse: 1300 mm/min - Travel X/Y/Z: 500/400/400 mm - Vertical milling head on column adjustable by 150 mm - Vertical and horizontal quill – SK40 - Vertical quill extendable by 90 mm - Drawbar thread: M16 - Weight approx. 1500 kg Accessories & Features: - 3-axis Heidenhain digital readout - Coolant system Iiodsxctyajpfx Aa Ejd - Chip tray - Central lubrication system About the machine: For sale is a Deckel FP4M universal milling machine, CE compliant and in very good condition. The machine has been partially overhauled, displays minimal backlash on the handwheels, and all lead screws move smoothly and evenly. Even at maximum speeds, the milling machine runs quietly. Rapid traverse is available on all axes; all bellows are new. The rigid angle table has been freshly planed. This is a reliable and user-friendly machine. An oil change has been performed. Mechanically and electrically tested. The Heidenhain digital readout makes operation easier and even more precise. Take advantage of the opportunity to inspect and test the machine under power on site.

Condition: excellent (used), Year of construction: 1978, functionality: fully functional, Universal milling machine Deckel FP1 with 3-axis digital display K&C infinitely variable feed in light gray Super condition Technical data: >> Year of construction 1978 Machine no. 2101-0465 >> Rigid angle table >> Speed: 40 - 2000 rpm >> Feed stepless 2 axes >> Drive power .:1,5 / 1,9 KW >> Spindle brake >> Rapid traverse >> Travel X/Y/Z: 300/160/340 mm >> Vertical milling head can be moved 100 mm on headstock >> Vertical quill and horizontal quill - SK40 >> Tightening system S20x2 >> Weight approx. 700 kg Accessories and equipment: Iisdpot Aav Isfx Aa Esd >> 3-axis digital indicator K&C Newly assembled with manufacturer's warranty and operating instructions. Display unit: Reference points, setting zero points, entering coordinates, mm/inch switching, absolute or incremental coordinates, circular functions, hole rows, radius milling functions, etc. >> Coolant device To the machine : We are offering a Deckel FP1 universal milling machine in very good condition. The machine has very little crank play and all spindles can be moved easily. The bellows are all new. On this newer FP1 model, the feed is infinitely variable in two axes and the machine also has a rapid traverse. An oil change has been carried out. Mechanically and electrically tested. The new digital display from K&C makes work easier and even more precise. Take the opportunity to inspect and try out this machine on site under power.

Condition: excellent (used), functionality: fully functional, Universal Milling Machine Deckel FP3 with 3-Axis Digital Readout RSF Elektronik Z-530!! Technical Data: >> Year of manufacture: approx. 1975, Machine No. 0681 >> Swivel and tilting table (recently overhauled) >> Speed range: 40 - 2000 rpm >> Feed and rapid traverse in 3 axes >> Drive power: 3 kW >> Travel X/Y/Z: 500/300/400 mm >> Features: Vertical & horizontal spindle >> Vertical quill and horizontal quill extendable - SK-40 >> Drawbar system M16 >> Weight approx. 1300 kg Equipment and Accessories: >> 3-axis digital readout RSF Elektronik Z-530 Iijdpfxoxu E I Hj Aa Esd >> Coolant system >> Central lubrication About the machine: For sale is a Deckel FP3 universal milling machine in good condition. All spindles move smoothly. Most of the bellows are nearly new. The swivel and tilting table is as new. An oil change has been carried out. The machine has been mechanically and electrically tested. The digital readout makes work easier and more precise. Take advantage of the opportunity to inspect and test the Deckel on-site under power. The machine is immediately available!!!

Year of construction: 1992, operating hours: 100 h, condition: used, functionality: fully functional, Description Corner crimper for pressing profiles with a height of up to 68 mm. Extremely high pressing force achieved by a large-volume bellows cylinder (maintenance-free). The machine is easy to adjust and operate. Counter bearing pneumatically positionable with mechanical locking Iiodpex Rvl Rjfx Aa Eod Support arms and pressing blades included as standard Two-hand operation for safe use Options Additional support Special pressing blade Technical Data Pressing height: 68 mm Pressing force: 40 kN (4 t) Drive: Pneumatic Compressed air supply: 7 bar Air consumption per cycle: 30 l Dimensions (L × D × H): 650 × 820 × 1,270 mm Weight: 205 kg

Condition: like new (used), Year of construction: 2017, workpiece weight (max.): 3,000 kg, travel distance X-axis: 800 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 510 mm, workpiece height (max.): 510 mm, workpiece width (max.): 1,250 mm, workpiece length (max.): 975 mm, empty load weight: 4,200 kg, Equipment: cooling unit, Fanuc Robocut C800iB - Model Year 2017 Fanuc's largest wire EDM machine AWF Automatic Wire Threading Turkish Control Unit - Touchscreen Fanuc Link i Remote Control Water Cooler Core Joint Part Holding Twin Servo Wire Tension Control Thermal Compensation Fanuc New Series 15" Touchscreen and Turkish Control Unit Able to make 5 cuts with the standard new power supply and achieve a surface quality of 0.30 microns. New lower head design and lower head tube protected by bellows. Twin Servo wire tension control ensures consistently stable wire tension during cutting, resulting in more precise cuts. Advanced AWF2 system allows for wire threading at the point of breakage. Program transfer and remote control via CF card, USB, RS232C, and Ethernet Standard Features Maximum throughput workpiece clamping (mm): 1250 x 975 x 500 mm Maximum workpiece weight (kg): 3000 kg X-Y axis travel (mm): 800 x 600 mm Z axis travel (mm): 510 mm U-V axis travel (mm): 200 x 200 mm Maximum cutting angle (°/mm) std. Maximum cutting angle (°/mm) opt.: ±30° / 150 mm : ±45° / 70 mm Minimum axis travel (mm): 0.0001 Wire diameter (mm): Ø 0.1 ~ Ø 0.30 Maximum wire weight (kg): 16 kg Footage (mm): 2900 × 3260 mm Machine weight (KG): 4200 kg Control unit: FANUC Isdpfx Asxfaqkoa Ejid

Condition: new, Year of construction: 2025, functionality: fully functional, grinding length: 1,500 mm, grinding width: 300 mm, total length: 3,000 mm, total width: 1,000 mm, grinding height: 150 mm, grinding wheel diameter: 300 mm, overall weight: 2,500 kg, grinding spindle motor power: 11 W, grinding wheel speed: 1,450 rpm, Equipment: documentation/manual, The GRAFS GRfix-1500e is a heavy-duty surface grinding machine designed for rough and high-performance grinding of steel plates. Developed and manufactured entirely in Poland, this model combines robust construction, long service life, and user-friendly electronic control. Main features: - Electromagnetic table 300×1500 mm, S-pole, holding force 120 N/cm² - Grinding motor 11 kW, high-quality Polish production - Segmented grinding wheel Ø300 mm, 6 aluminium oxide segments - Laser sensor for automatic workpiece height detection (as an additional option) - PLC control (Mitsubishi) with 7” HMI touchscreen – programmable grinding cycles (rough pass, automatic downfeed 0.001–0.05 mm, spark-out, pause, auto-stop) - Stepper motor feed with encoder for precise vertical adjustment - Mitsubishi inverter – variable carriage speed 1–16 m/min - Remote diagnostic support via Internet (Wi-Fi connection) - External coolant filtration system MS60 with rotary magnetic drum separator, 150 L tank, and 60 L/min pump - LED 24V working light and internal coolant pipe for table flushing - Powder-coated body: RAL7012 (frame) / RAL7021 (carriage) Mechanical design: - Extremely rigid welded steel body (10 mm thick plates, stress-relieved) - Carriage on PWTR precision rollers for smooth and silent motion - Replaceable hardened steel guide strips - Quick manual positioning of the carriage above the workpiece - Fast up/down movement of the spindle motor for easy tool change - Easy mounting system for the grinding wheel – only three bolts - Maximum workpiece height: 150 mm Iiodpsxmhyijfx Aa Esd Optional equipment: - Accordion-type bellows covers - Alternative coolant filtration units (magnetic, paper, or combined) Advantages: - Perfect for rough surface grinding of large steel plates - Designed for high efficiency and long-term stability - Fully European components – Mitsubishi Electric control system - CE conformity, electrical inspection and Polish technical documentation (DTR) included Warranty: 12 months Technical data summary: Parameter Specification Grinding table: 300 × 1500 mm (electromagnetic, S-pole) Max. workpiece height: 150 mm Grinding wheel: Ø300 mm, 6 segments Spindle motor power: 11 kW Carriage speed: 1–16 m/min Downfeed: Automatic 0.001–0.05 mm Control system: PLC + 7” HMI Mitsubishi Coolant system: MS60 magnetic separator, 150 L tank, 60 L/min pump Weight: ~2800 kg (depending on configuration) Power supply: 400V / 50Hz Made in Poland The GRAFS GRfix-1500e is a professional surface grinder built for intensive, rough grinding applications where high metal removal rate and long-term precision are essential. A reliable, industrial-grade solution for steel fabrication shops, tool manufacturers, and service centers.

Year of construction: 2017, operating hours: 5,000 h, condition: ready for operation (used), functionality: fully functional, Three Geneglace machines installed in one insulated container with ice-collector screw bellow allowing ice for direct drop into ice-bin or to a rotary valve that blows the ice to location (up to 60 meter). The icemachines are connected to a Bitzer screw compressor unit in a pumpsystem using a horisontal liquid separator. The system has a air-cooled condenser in cascade with a schell&tube condenser. If used for leisure snow machine, this is a 100% mobile unit and makes 100m3 meter of dry sub-cooled ice pr. day Iiodpfx Aow R Da Usa Eod Machiner is for Freon only, like R449a or R404a or similar.

Condition: used, Year of construction: 2017, functionality: fully functional, bending force (max.): 36 t, TRUBEND CELL 7000 High-End Aut. bending cell Year of construction: 05/2017 ADDITIONAL Functions: ToolMaster Bend (incl. Tool Identification System - TIS) Tool gripper for faster tool change (only in conjunction with ToolMaster Bend and gripper changing module) Conveyor belt Additional system pallet Additional mechanical gripper (without jaws) Additional jaws for mechanical finger gripper Gripper changing module incl. tool cleaning station Multi-suction device with flat suction cups and electromagnets TCB - Thickness Controlled Bending STANDARD configuration: TruBend 7036 Cell Edition - Stable Machine frame - Electro-mechanical direct drive (torque motor) - 6-axis backgauge system with stop sensor - Segmented Wila tool clamps without Tool Identification System - TIS ATTENTION: lower tool clamp in the same design as the upper tool clamp - Switch cabinet air-conditioning BendMaster (15) - Stable frame and manipulator - Bearing load: 15 kg, max. sheet load: 3 kg - Floor tracks: Welded construction with stable guide rail. Travel 3215 mm - Gripper coupling at BendMaster - Electrical drives - Mechanical finger gripper with jaws Iisdpfoyalx Rjx Aa Ejd LoadMaster Bend - Handling system - Multi-suction device with bellows suction cups - Double sheet detection and separation - Transfer station - System pallet Safety - Safety cell with swing sliding doors: The complete working and danger zone is safeguarded by a safety cell Lighting Control system - PC control with 19“ Touch screen - Mobile operating terminal - Network connection - Teleservice via Internet

Year of construction: 2024, condition: new, functionality: fully functional, machine/vehicle number: CO2-1125-5000, 1x Vacuum Belt Filter Completely constructed in stainless steel 1.4404/1.4571, grates in stainless steel 1.4301 Finish: pickled and passivated Including: 1x drive roller 508x1427 1x steering roller 88.9x1850 6x support/tension rollers 88.9x1850 1x VBF frame 1x VBF hood frame 1x safety grilles (1.4301) 2x spray pipes, each fitted with 12 nozzles 6x hood brackets for vacuum tube 1x mounting materials, incl. gaskets 1x holder for control valve and paddle 2x slide blocks for tension roller HMPE100 2x bearing blocks for scraper blade HMPE100 1x scraper blade HMPE100 1x drive SEW KH87/T R57 DRN90L4TF 2x bellows d100 wbz 100-E1 2x misalignment switches 2x emergency stop switches 2x emergency stop cords 1x pressure reducer 1x hose and coupling for connection to bellows 23x nozzle holders 23x nozzles 4x rubber seals for wash cabinet 1x rubber seal for suspension conveyor 2x double wash gutters Iiodpfx Aasxfvahj Eod

Condition: ready for operation (used), Year of construction: 2009, Travel ranges working area 1: X: 6450mm, Y: 1535mm, Z: 250mm, working area 2: X: 6200mm, Y: 1535mm, Z: 250mm, working area 3: X: 6200mm, Y: 1520mm, Z: 275mm, axis travel configuration 1: X: 6820.5mm, Y: 1963mm, Z: 350mm, axis travel configuration 2: X: 6820.5mm, Y: 1963mm, Z: 350mm, axis travel configuration 3: X: 6820.5mm, Y: 1963mm, Z: 663mm (5-axis head), Z: 350mm (additional machining units), control: Biesse XP600. Maintenance: complete C-axis was replaced in 2015 including accessories, vacuum pump was fully replaced in 2016 including bellows, hoses and additional components, in 2021 the machine was equipped with a new high-performance control PC running a current Windows 10 operating system. With extensive documentation. An on-site inspection is possible. Iisdpfx Aeylziija Eed

Condition: new, mileage: 5 km, power: 132 kW (179.47 HP), fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: mechanical, loading space length: 4,800 mm, loading space width: 2,100 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), soot filter, New German vehicle: * Euro 6 * 6-speed gearbox * Start/Stop * GVW 3,500 kg. * ABS + ESP + ASR * Driver airbag * Manual air conditioning * Central locking with remote control * Electric front door * Electric exterior mirrors * Trailer hitch with 3000kg towing capacity * All-weather tires Vehicle transporter - EPS4VA construction * Subframe and substructure made of aluminum profiles * Dimensions of loading area approx. 480 x 210 cm. * Own weight approx. 350 kg. * Full aluminum structure * Aluminum loading ramps approx. 220 cm long * Side marker lights (LED) orange * Side limit lights (LED) red / white * Cable winch Options on request: * Structure for double-tire chassis * Aluminum loading ramps approx. 200-220 cm inserted in sills behind the rear wheels * Cable winch with cable winch shifting. * Ball coupling behind the driver's cab * Additional socket behind the driver's cab, 7 or 13 pin * Additional air suspension, three-fold bellows with dual-circuit system, 2 pressure gauges with valve * Compressor for additional air suspension * Storage box * Wheel stoppers / wheel chocks * Work lights * Light bar carrier * Light bar * LED work lighting integrated into the side of the loading floor * Trailer type Modello, 550x205, 3500kg, price on request Load securing also available from us: * Tensioning and lashing straps * Locking bars * High visibility vests * Transport boxes * Edge protection * Storage bags * Wheel stoppers * etc. Financing and leasing possible We manufacture bodies of any size on any chassis. Tarpaulin, GRP sandwich, aluminum. visit us at: Bodies - Trailers - Advice - Financing Ijdsnq Eh Aopfx Aa Eoid Subject to errors and prior sale, no liability for printing and input errors.

Condition: new, Year of construction: 2026, turning height: 3,000 mm, workpiece weight (max.): 50,000 kg, turning diameter: 4,200 mm, feed length X-axis: 4,700 mm, feed length Z-axis: 2,000 mm, faceplate diameter: 4,000 mm, feed rate X-axis: 25 m/min, feed rate Z-axis: 15 m/min, rotary table diameter: 4,000 mm, rotational speed (max.): 100 rpm, torque: 128,000 Nm, spindle speed (min.): 3,000 rpm, table load: 50,000 kg, power: 100 kW (135.96 HP), Equipment: rotational speed infinitely variable, TECHNICAL DATA: Machining diameter 4200 mm Max. workpiece height 3000 mm Max. workpiece weight 50,000 kg Faceplate diameter 4000 mm Faceplate speed range 0-30/0-100 rpm Max. faceplate torque 128,000 Nm Main drive power 75/90 kW Iijdpfx Aajq Ny Dte Ejd EQUIPMENT: -1-2 support configuration -Machine enclosure -Chip conveyor -Cooling water preparation -C-axis -Fork head -Driven tools/BT50 -Bellows cover -Central lubrication SKF/VOGEL -12-month warranty -Complete electrical equipment 230/400 V, 50 Hz, Made in Germany, CE standard CONTROL: FAGOR or SIEMENS OTHER: Geometry acceptance according to DIN 8609-3

Condition: new, Year of construction: 2026, Through our many years of experience in service, we have decided to develop and produce our own milling machines. Iiedeh Su Ipepfx Aa Eed The FPS 500M is a conventional milling machine perfect for training and production. Through the Heidenhain Positip 8016 active digital display positioning and for example the creation and approach of a bolt hole circle is possible. Control Heidenhain Positip 8016 Active - Digital display Speed 0 - 3000 rpm geometrically stepped direct gear with 16 gear steps for maximum torque / milling power Feed rate 0 to 500 mm/min, infinitely variable rapid traverse 1,5 m/min quill extendable quill, vertical 80 mm SK40 optional: horizontal work spindle or horizontal quill (approx. 100mm extendable) Pulling system: hydraulic tightening system - DIN 69872 optional: DIN 2080 Axes X/Y/Z 500/400/400 mm Table Rigid angular table 800x480mm Equipment - Vertical and horizontal spindle - Milling head manually tiltable +/- 90 °. - Travelling chip tray - Machine light - Central lubrication - Z-axis bellows Options - universal table - rotary table - Shaper head - dividing head - counterholder - etc. Further technical data can be found in the attached data sheet.

Condition: new, We can deliver all spare parts for JUNG JF- und HF-series. z.B. grinding flanges, switches, bellows, refurbished grinding and transvers spindles, hydraulic pistons etc. Also equipment like magnetic chucks (new oder refurbished), dressers, Iiodpfxegbt U Ns Aa Eed filtrtion units, lubrication pumps etc. Also used parts which are discontinued by the manufacturer. Please inquire wih the exact part name.

Condition: used, Year of construction: 2020, functionality: limited functionality, overall weight: 150 kg, GRUNDFOS Electronically Controlled Dry-Running Pump TPE 100-250/2-S A-F-A-BAQE-ND1 Single-Stage Inline Pump Art. 99114824 PN16. 3 x 380-500 V DN100 with MGE160MH-2-FF300-JA Motor We are offering the Grundfos electronically controlled dry-running pump. ⭐︎ Condition: Good (used) The electronically controlled dry-running pump is used but fully operational. The pump was functioning flawlessly up until removal a few weeks ago. Manufacturer: Grundfos Model: TPE 100-250/2-S A-F-A-BAQE-ND1 Description: Single-stage inline pumps with speed-controlled MGE motor Frequency converter: integrated Pump speed: 2930 rpm Rated flow: 135 m³/h Rated head: 20.1 m Isdpfsyc T Apsx Aa Eeid Mechanical seal: BAQE Pump housing: Cast iron Impeller: Cast iron Gross weight: 157 kg For further technical details, please refer to the nameplate. Scope of delivery as shown. Inspection prior to purchase is possible and expressly encouraged. 2 units available. Price: per unit #Shelf 21-1-9 Shipping possible, but buyer pays shipping costs. Single-stage volute pump with opposing suction and discharge ports in inline design. Suction and discharge ports have the same diameter. The pumps are constructed according to the top-pull-out principle, i.e., the pump head (motor, headpiece, and impeller) can be easily removed for servicing or maintenance while the pump housing remains in the piping. The pump is equipped with an unbalanced rubber bellows seal. The mechanical seal complies with EN 12756. Piping connection via DIN flanges PN 16 according to EN 1092-2 and ISO 7005-2. The pump features a fan-cooled permanent magnet synchronous motor. The motor efficiency corresponds to energy efficiency class IE5 according to IEC 60034-30-2. For speed control, the motor is equipped with a frequency converter and PI controller, both integrated into the motor terminal box. Electronic speed control enables continuous adaptation of motor speed and thus pump output to current demand. The pump is equipped with a differential pressure sensor.

Condition: used, mileage: 910,670 km, power: 335 kW (455.47 HP), first registration: 05/2019, fuel type: diesel, overall weight: 18,000 kg, axle configuration: 2 axles, next inspection (TÜV): 05/2026, brakes: retarder, color: white, gearing type: automatic, emission class: euro6, Year of construction: 2019, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, soot filter, Special equipment: Axle load measuring device, driver's side airbag, rear cab wall work lights (top), right exterior mirror with maneuvering position, bi-xenon headlights, compressed air connection in cab, air horns (2) on cab roof, cab: with air suspension, cab floor with 170 mm engine tunnel, 12.7 cm info display with additional indicator, cool box / refrigerator, light and rain sensor, air intake behind cab, roof air deflector (lockable) and side air deflectors, mounting plate / 40 mm saddle plate for fifth wheel coupling, reinforced engine brake, PTO MB 131-2c, programmable special module, chassis lowering without residual pressure control on bellows, chassis height lowered by 25 mm, tire pressure monitoring system, spare wheel, retarder, drawers under side rail, automatic circuit breaker, cab seats: passenger seat with armrest, cab seats: driver’s comfort suspension seat, external sun visor, steel rims 11.75x22.5 (front axle), 12V socket in passenger footwell, 24V / 25A socket in passenger footwell, carpet on engine tunnel, preparation / switch for lift axle on trailer/semitrailer, additional thermal insulation, transmission oil cooler. Further equipment: Emission standard EURO 6, axle configuration: 4x2, front axle load 7.5 t, Actros 4, trailer socket 24V / 15-pin, work lights, audio system: radio with USB connection, exhaust outlet to the right, electric and heated external mirrors, rear axle differential lock, steel air reservoir, medium compressed air unit, driver assistance system: attention assist (drowsiness detection sensor), driver assistance system: brake assist (Active Brake Assist), driver assistance system: lane keeping assist, cab width 2.30 m, cab: L ClassicSpace, suspension: leaf/air, front spring support aluminum, front springs 7.5 t, 1 leaf, electric window lifters, tinted windshield, generator 100 A, 12-speed transmission - type: G 211-12, AdBlue tank: 60 liters, manual roof hatch (steel), rear axle crown wheel 440, body/superstructure: tractor unit, lower comfort bed, central locking system, communication interface, 3-part mudguard, fuel tank: 390 liters aluminum, radiator shutters, regulated power steering pump, 2-stage air compressor, engine 10.7 l - 335 kW inline 6 diesel (OM 470), engine compartment encapsulation, ramp mirror, residual heat utilization, disc brakes front and rear axles, seat upholstery: fabric, cab seats: passenger functional seat, cab seats: driver's seatback folding, voltage converter 24V / 12V 10A, front splash guard, front axle stabilizer, external left storage flap, 24V cab outlet, tachograph / EC control unit, cab door extension, aerodynamically shaped underbody paneling, front underrun protection, CB radio preparation, toll recording preparation, cranked front axle, regulated water pump, permissible total weight 18,000 kg, additional heater (water-based). Iiodpfxoxcc H Ne Aa Esd —As viewed or offered, without further services / accessories. Our offer is in general without new TÜV inspection. Should a new TÜV inspection be required, we will gladly provide a quote from our partner workshops! Vehicle may display advertising stickers and/or lettering. Our general terms and conditions of delivery and payment apply. We support you with export, preparation of export documents, procurement of license plates, supplier declaration, etc.! The information provided in advertisements, online, price tags, and images are non-binding descriptions and

Condition: used, Year of construction: 2009, functionality: fully functional, 1 Universal Testing Machine Type H 10 KM Used device with Windows 11 software for tensile, compression, and bending tests; comes with one pair of wedge grips up to 10 kN and a certificate for tensile and compression displacement measurement. For testing in tension, compression, shear, bending, etc. • This is a dual-spindle benchtop model. • The machine complies with DIN 51220 and 51221, Class 1. • Digital display for force and displacement, 4½ digits, with peak value memory. • Five-range automatic switching for force and displacement measurements. • Digital speed adjustment from 0.5 to 1000 mm/min in increments of 0.1 mm. • Break detector and automatic return function are standard features. • Driven by a precision servo motor with high-frequency chopper control unit and digital feedback for load-independent, constant speed. • Quiet operation thanks to toothed belt drive and ball screw spindles with bellows cover. • Fully computer-controllable via RS 232 interface. Max. load: 10 kN in tension and compression Max. travel: 1150 mm without grips Force measurement: Strain gauge Iisdpfx Aexghlfea Ejd Measurement principle: Temperature-compensated Displacement measurement: Built-in optical encoder, 0.01 mm resolution Power supply: 220-250 V, 50-60 Hz Power consumption: 1.0 kW Dimensions: Height 1575 mm, Width 635 mm Clear width of frame: 410 mm Weight: approx. 95 kg Includes: 10 kN load cell and certificate for force and displacement.

Condition: new, empty load weight: 501 kg, maximum load weight: 1,299 kg, overall weight: 1,800 kg, loading space length: 3,500 mm, loading space width: 1,800 mm, loading space height: 100 mm, loading space volume: 0.6 m³, color: silver, Hydraulics, automatic reversing, hot-dip galvanizing, * IMMEDIATELY AVAILABLE * Technical data: - Type: New vehicle - Availability: IMMEDIATELY! - TÜV: 2 years from first registration - Floor: Multiplex floor with anti-slip surface - Gross vehicle weight: 1,800 kg - Unladen weight: 501 kg - Payload: 1,299 kg - Loading area dimensions: 350 x 180 x 10 cm (L x W) - Drive-on angle approx. 4 ?. - Tires: 195/50 RC 13C - Brake: yes - Support wheel: yes - Incl. vehicle documents (letter) - 100 km/h approval: Included! AA118/3518, top model, car transporter with one axle line, equipped with fully electronic air suspension system. For the regular user looking for the best possible quality. Mounting of the suspension system completely under the vehicle. Equipped with an 18 bar quality compressor with air dryer, electronic control and height control. 12V 70Ah vehicle battery. Particularly simple button operation. Only works with a fully connected 13-pin plug! Depending on choice with 18mm multiplex floor or 19mm aluminum floor profiles. Optionally with an additional remote control and/or with an additional air tank (5 liters). Standard equipment: - thermally galvanized chassis - very stable welded steel frame - rear sloping rear - very stable V-drawbar - plastic mudguards - wheel suspension, independent air suspension - incl. 100km/h approval - loading area can be lowered to the road surface or the ground by means of air suspension, drive-on angle approx. 4 ?. - Electronic air suspension - 2 air bellows - 2 adjustable shock absorbers - emergency valves, for external filling of the air suspension - 195/50 RC 13C tires - polyamide air hoses - stainless steel couplings - custom-made wiring harness - function only with fully occupied 13-pin socket - mounting suspension system completely under the loading area - 2 sensors for height control - electronic control in the drawbar - compressor 12V 18-bar - Made in Germany - integrated 12V, vehicle battery, 70Ah - plug for external battery charger - ASCU control system - 15mm multiplex floor panel, made of birch wood, with anti-slip coating and full-surface - lashing points, left, right and front - folding license plate holder with LED lighting, - support wheel, automatic - large-dimensioned safety lighting - integrated rear fog light - reversing light - 13-pin plug - registration papers: COC papers Accessories / optional extras available: - all-aluminum floor - tarpaulin AA3518, 330x180x180/193cm (LxWxH) desired color 4x zigzag lock from - box body AA3518, 25mm isol. panels met alum. Roll-up door - Fixed front wall / high front grille - 2. Compressor with additional air tank - Wireless remote control for air suspension system - External battery charger - Battery charger integrated in the vehicle with 230V connection - Spare wheel 13 inch - Aluminum alloy rims - Spring rod Autostop / wheel stopper to prevent driving too far - Mobile emergency compressor - Storage box for accessories - Winch hand 820 kg braked - Winch hand 1200 kg braked - Winch hand 1450 kg braked - Weather protection cover for winch New vehicle with warranty and TÜV. We are happy to offer you suitable financing !, Descriptions and pictures are protected by copyright !!! Over 800 trailers immediately available for you! We are Brian James / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Debon / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialist for over 30 years. Iodpfxju Hrxwj Aa Esid