Machining centre

Mazak Vertical Centre Nexus 510C-II

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Pjdjwp Rqfepfx Ahyegk Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: good (used), Year of construction: 2012, Parts shown by hand not come. X1020mm Y610mm Z610mm 12.000 rpm,25 KW, 160Nm Control unit: HEIDENHAIN iTNC 530, 4th axis will come without parts shown by hand. Pgsdpsx Awzbsfx Ahyek

Condition: ready for operation (used), Year of construction: 2017, operating hours: 3,163 h, travel distance X-axis: 1,016 mm, travel distance Y-axis: 508 mm, travel distance Z-axis: 635 mm, controller manufacturer: HAAS, table load: 794 kg, spindle speed (max.): 12,000 rpm, number of axes: 3, This 3-axis HAAS VF-3SS was manufactured in 2017 and features a robust Haas CNC Control. It offers X-axis travel of 1,016 mm, Y-axis travel of 508 mm, and Z-axis travel of 635 mm. The machine supports a spindle speed of 12,000 rpm and a rapid traverse of 30.5 m/min. If you are looking to get high-quality milling capabilities, consider the HAAS VF-3SS machine we have for sale. Contact us for more information. • Machine hours (as shown on the screen): Pjdpfx Ahjx D I Stoysgk • Power On: 25,416 h • Cycle Start: 8,164 h • Table: • Size: 1,372 × 457 mm • Tool changer: 30+1 positions (side-mount) • CNC control: Haas CNC Control

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, CNC Turning and Milling Center - DMG GILDEMEISTER - CTX gamma 1250 TC YOM: 2009, until 2011 showroom machine, from 2012 operating The machine can be inspected by appointment in the factory under power. Condition: Good (high accuracy), ready for immediate use. Spindle hours (August 1st, 2025): 9.580 h The heart of the machine is the integrated traveling column with turning milling spindle and interpolating B-axis. Machine basic data: * Part hollow clamping device (hydraulic) * C-axis * Cross slide above with turning/milling spindle as motor spindle, with hydraulic clamping in turning, tool holder: Capto C6 * Y-axis: +/- 200 mm * B-axis: +/- 120° * Disc-type tool magazine * Absolute, direct measuring systems in X-, Y-, Z1-axis * USB-interface, Ethernet interface Pgedpfx Aew Hg Nlohyok TECHNICAL SPECIFICATIONS: * Control: Heidenhain CNC Pilot 4290, 3-D path control TURN PLUS Working area: * Swing diameter over bed: 630 mm * Turning diameter: 630 mm * Spindle distance: 1.510 mm * Bar diameter max.: 65 mm Main drive I: * Drive power (100% / 40% ED): 24 / 34 kW * Speed range from - up to: - 5.000 rpm * Speed of the C-axis: - 5.000 rpm Turning/milling spindle: * Tool holder: Capto C6 * Spindle speed: - 12.000 rpm * Drive power (100% / 40% ED): 13.2 / 22 kW * Torque (100% / 40% ED): 60 / 100 Nm Tool magazine: * Number of tools: 36 * Dimensions of the machine approx. (Width/Depth/Height): 6.860 x 4.220 x 2.530 mm * Total weight of the machine approx.: 18,5 tons EQUIPMENT: * Well equipped … * No steady rest available * Documentation complete available. Detailed technical data sheet and information on equipment available on request. There is no guarantee for correctness and completeness of the technical details and and accessories.

Condition: excellent (used), CPM 2000 granulator, 90kW engine Pjdpfxjwcdpns Ahyjgk die diameter 410mm We have several pieces

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit Pedpfxsu Hmace Ahyegk non-driven extraction table Machine workshop checked Machine cleaned and repainted

Condition: refurbished (used), FULL LINE of Drilling, max working width mm 3200, with fast automatic handling equipment. Composed of the following machines: A) LOADER (Portal) "RBO" Winner C 3200 with double pick-up and central motorized rollers table. With 2 on-ground motorized rollers ways to in-feed the piles (stacks) of panels to loader. Pjdpfxedfgg Io Ahyegk B) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° C) 1st Auotmatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units D) 2nd Automatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units E) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° G) UNLOADER-STACKER (Portal) "RBO" Winner SC 3200 with double pick-up, with double storage station, with central motorized rollers table. With 2 on-ground motorized rollers ways to out-feed the piles (stacks) of panels from the Unloader

Condition: ready for operation (used), Year of construction: 2005, spindle speed (max.): 5,000 rpm, travel distance X-axis: 230 mm, travel distance Z-axis: 575 mm, spindle motor power: 26,000 W, total height: 1,840 mm, overall weight: 5,100 kg, controller manufacturer: MAZATROL, number of axes: 3, This 3-axis Mazak Quick Turn NEXUS 200MS was manufactured in 2005. It features a maximum turning diameter of 380 mm, main spindle speed up to 5000 rpm, and a sub-spindle speed of 6000 rpm. The machine includes a Mazatrol 640T Nexus CNC control and has a robust design with dimensions of 2765x1780x1840 mm, weighing 5100 kg. If you are looking to get high-quality turning capabilities consider the Mazak Quick Turn NEXUS 200MS machine we have for sale. Contact us for more information. Machine Benefits Technical Machine Benefits • Maximum turning diameter: 380 mm Podpfex D Rmtox Ahyegk • Maximum bar diameter (main spindle): 65 mm • Maximum bar diameter (sub-spindle): 42 mm • Distance between spindles: 580 mm Extra Information Machine has only worked in small batch 1-shift production. Dimensions Machine Depth 2765 mm

Condition: good (used), Manufacturer: Haver & Boecker Documentation available Podpfx Asv Sz Tdehyjgk Mechanical conversion from 50 kg to 25 kg bags in 1999 Control system: Siemens S7 Upgraded to the latest standard with spare parts support in 2015 Supported bag types: Quicklime, hydrated lime, cement, gypsum

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, CNC Turning- and Milling Center (Multi-functional-Machine) | Brand: MAZAK Type: INTEGREX e-650H II | Year of construction: 07/2009, Commissioning: November 2009 The machine can be inspected under power by appointment. Condition: Fully functional / operational. Operating hours (as at 10 March 2026): - Total: 91.430 h - Automatic operation: 52.054 hours - Automatic machining: 38.974 hours - Pure machining: 31.316 hours TECHNICAL SPECIFICATIONS: Workspace: - Max. Swing diameter: 920 mm - Max. Swing diameter over tool slide: 920 mm - Max. Turning diameter: 1.100 mm Main spindle: - Max. speed: 1.600 rpm - Min. speed: 35 rpm - Spindle bore: 260 mm (1.000 rpm) - Spindle nose: A2-11" - Spindle bearing inner diameter: 220 mm - Rated power (30 min. operation / 100% continuous operation): 45.0 / 37.0 kW - Max. torque: 4.500 Nm Tailstock (programmable): - Chuck: MK 6 Milling spindle: - Turret type: Single-spindle with ATC - Tool shank: Steep cone 50 - Max. tool diameter: 260 mm - Max. tool length: 500 mm - B-axis indexing increments: 0,0001° - B-axis positioning for turning - Min./max. milling spindle speed: 35 - 10.000 rpm - Milling spindle motor, AC: 37 kW Travel ranges: - X-axis: 1.025 mm - Y-axis: 650 mm - Z-axis: 6.423 mm - B-axis swivel range: 240° Dimensions: - Spindle centre height: 1.350 mm - Length: 13.267 mm - Width: 3.938 mm - Height: 3.920 mm - Weight: 41 tons Additional information: - Rated power (100% continuous operation): 99,5 kVA Automatic tool changer: - Number of tools: 120-position, SK50 DIN 69871 SPECIFICATIONS / SPECIAL ACCESSORIES: - Numerical control: MAZATROL MATRIX - Documentation - CE marking - Further excellent optional extras ... Pgedpfxeyuq Dzj Ahyek Without guarantee of completeness and correctness of the technical information and the equipment. - Subject to prior sale - Detailed technical data sheet and information on equipment available on request.