Pneumatic press for aluminum profiles

Condition: ready for operation (used), Year of construction: 1985, machine/vehicle number: 1304, functionality: fully functional, pressing force: 367 t, stroke length: 100 mm, table width: 525 mm, table length: 430 mm, table height: 800 mm, No minimum price – guaranteed sale to the highest bidder! EXW – Buyer is responsible for dismantling and loading! The machine was rebuilt in 2018! TECHNICAL DETAILS Press force: max. 3,600 kN Ram stroke: max. 100 mm Ram adjustment: 40 mm Stroke rate: 40 strokes/min Table area: 430 × 525 mm Table height: 800 mm MACHINE DETAILS Connected power: 7.5 kW Mains connection: 3-phase, 380 V, 50 Hz Nodpfx Ajz Tf Eneg Rjwn Control voltage AC: 220 V Control voltage DC: 24 V Main motor power: 7.5 kW Oil capacity: 50 l Ambient temperature: +5 °C to +40 °C Average temperature over 24 h: max. +35 °C Humidity: 30–95 %, non-condensing Altitude: 1,000 m above sea level Noise level: ≤ 70 dB Dimensions & Weight Dimensions (W x D x H): 1,200 x 2,000 x 2,400 mm Space requirement: approx. 1,500 mm Machine weight: 8,000 kg Control cabinet dimensions: 800 × 1,200 × 300 mm Control cabinet weight: approx. 100 kg EQUIPMENT Operating manual Testing information Digital documentation Note: Induction unit is not included in the scope of supply.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SÇ 902 S Hidrolik Alüminyum Köşe Presi Makinesi, • Complies with CE standards • Corner press machine designed for joining aluminium profiles at 90 degrees • 2 upper presses and blade movement are hydraulic • Equipped with a mm scale system for adjusting blade height and feed • Centering square stop is hydraulic • Drain button for fine adjustment is available • Machine comes with 2 pieces of 4 mm blades • 2 pedals are used for hydraulic pressing and profile clamping Nsdpfjrbk Tfsx Ag Rown • Polyamide plate is provided to prevent damage to profile surfaces • Left and right profile support arms are available

Year of construction: 2025, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 54942, No minimum price – guaranteed sale to the highest bidder! EXW – Dismantling and loading must be organized by the buyer! TECHNICAL DETAILS Nominal test force: 50 kN Test stroke: < 1,400 mm Usable distance between pressure plates: approx. 800 mm Test area width: 500 mm Test speed: continuously variable 0.001–1,200 mm/min Resolution of displacement measurement: ≤ 0.001 mm Diameter of pressure plates: 246 mm Centering bore: 40 mm Thread: M12 Hardness: ≥ 56 HRC Design: Steel, hardened, rotatable at the top and bottom, lockable at 0° Measuring range of the enveloping circle: 30–250 mm Design: Probe with bearing rollers Measurement: Recording under load MACHINE DETAILS Control system: Control system with control computer Test program: Enveloping circle measurement Network: Fast Ethernet, 100 Mbit/s between the control computer and the separately required operating PC Software delivery: USB stick with installation software Documentation: Version and license status not documented separately Last calibration: 08/04/2025 Dimensions & Weight Machine dimensions: approx. 750 × 900 × 1,950 mm Base frame dimensions: approx. 730 × 900 × 700 mm Control cabinet with control computer dimensions: approx. 600 × 600 × 1,900 mm Machine weight: approx. 490 kg Base frame weight: approx. 50 kg Voltage supply: 3 × 400 V AC, 50 Hz, N + PE Type plate power: 3,000 W Connected power: approx. 3 kVA EQUIPMENT Base frame Control cabinet with control computer Rotatable pressure plates Enveloping circle measuring device with probes and bearing rollers USB stick with installation software Compressed air connection: Pneumatic connection with shut-off valve Nwsdpfx Agez Tf D Re Ron Note: The functionality has been tested and confirmed. However, an unresolved error message on the drive prevents further use. The machine is in like-new condition visually. The operating PC is not included in the offer.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2019, total length: 495 mm, total height: 780 mm, total width: 585 mm, overall weight: 17 kg, No minimum price – guaranteed sale to the highest bidder! EXW – Dismantling and loading are to be organized by the buyer! The system is available immediately! TECHNICAL DETAILS Nwjdpfx Aoz Tf D Dog Ren Build volume X-axis: 230 mm Build volume Y-axis: 190 mm Build volume Z-axis: 200 mm Layer height: 0.06–0.4 mm Build plate: Heated glass plate Build plate temperature: up to 120 °C Filament diameter: 2.85 mm Nozzle temperature: up to 280 °C Print speed: up to 150 mm/s Material flow: up to 24 mm³/s Compatible print cores: AA 0.4; BB 0.4; AA 0.25; AA 0.8; BB 0.8; CC 0.4; CC 0.6; DD 0.4 MACHINE DETAILS Technology: Fused Deposition Modeling (FDM) Software Print preparation: UltiMaker Cura, Cura Cloud Printer management: UltiMaker Digital Factory Supported operating systems: Windows, macOS, Linux Environmental conditions Operating temperature: 15–32 °C Operating humidity: 10–90% RH, non-condensing Storage temperature: 0–32 °C Non-operating humidity: 10–90% RH, non-condensing Installation: Away from direct sunlight Power supply: 100–240 V AC Mains frequency: 50–60 Hz Power consumption: 350 W Operating noise: < 50 dB(A) Connectivity: WLAN 2.4 GHz, LAN, USB Monitoring: HD camera Dimensions & Weight Dimensions: 495 × 585 × 780 mm Net weight: 14.4 kg Operating weight: approx. 17 kg EQUIPMENT Dual-extrusion print head Automatic nozzle lift system Interchangeable print cores Dual-gear feeder Filament flow sensors Dual spool holder with NFC detection Color touchscreen HD camera Heated glass plate PEI print bed Spool holder with material guide Power cord Ethernet cable USB stick Operating manual CE marking Print Core AA 0.4 – 2 pieces Print Core BB 0.4 – 1 piece Nozzle cover – 3 pieces

Condition: used, Hydr. flat form scissor lift table FLEXLIFT FLUNDER type 1500 / 100 (without hydraulic unit) Year of manufacture 1991 Nominal lifting capacity 1500 kg Lifting capacity (practically tested) 1000 kg (at approx. 350 bar) platform size 2100 x 1400 mm stroke max. 930 mm Overall height - bottom 100 mm (with mounting frame) Overall height - top 1030 mm Nsdpfx Agsl Nbqcj Rown Hydr. operating pressure 350 bar = lifting force 1000 kg Motor power of hydraulics 1,5 kW mains connection 400 Volt, 50 Hz - mechanical-hydraulic safety limit switches stop the lowering process when the safety bar is actuated - without hydraulic power unit - without electric control length of installation frame 2270 mm width of mounting frame 1580 mm height of mounting frame = height at bottom 100 mm dead weight of lifting table 500 kg good condition

Condition: excellent (used), functionality: fully functional, TECHNICAL DETAILS General Information Nedpfx Ajz R Dwksg Rown Manufacturer: Baykal Type of Machine: Hydraulic Plate Shear Model: HNC 8100/6 Working Area Working Width: 8,100 mm Sheet Thickness: max. 6 mm EQUIPMENT Motorized Back Gauge Automatic Shear Gap Adjustment Automatic Angle Adjustment Sheet Support Device

Condition: excellent (used), Year of construction: 2016, TECHNICAL DETAILS Control System CNC control: FANUC Professional 5 Axes and Travel Ranges X-axis: 550 mm Y-axis: 1,000 mm Z-axis: 500 mm C-axis: 360°, continuous rotation A-axis: 150° (+30° / 120°) C-axis measuring system: Rotary encoder A-axis measuring system: Rotary encoder Feed Rate and Rapid Traverse Feed rate X-axis: 32 m/min Feed rate Y-axis: 40 m/min Feed rate Z-axis: 40 m/min Rapid traverse X-axis: 48 m/min Rapid traverse Y-axis: 50 m/min Rapid traverse Z-axis: 50 m/min Rapid traverse A-axis: 18 m/min Rapid traverse C-axis: 18 m/min Work Table and Workpiece Table dimensions: 500 mm Maximum workpiece size: 650 × 500 mm Workpiece weight: max. 350 kg Spindle Spindle speed: max. 14,000 rpm Nwedps Aayfhsfx Ag Ren Tool System Tool holder: HSK-A63 Tool magazine: 323 positions Tool changer: Double gripper Tool diameter: max. 70 mm Tool diameter with adjacent occupied positions: max. 140 mm Tool length: max. 300 mm Tool weight: max. 8 kg Operating Hours Total operating time: 63,813 h Spindle running time: 30,592 h Machine Dimensions and Weight Length: 3,550 mm Width: 2,900 mm Height: 3,200 mm Machine weight: 15,700 kg EQUIPMENT Electronic handwheel Chip conveyor Measuring probe

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in Njdpfet Tqy Eox Ag Rewn heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, Year of construction: 2019, battery capacity: 1,376 Ah, battery voltage: 80 V, overall weight: 2,500 kg, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Battery type: 8 PzS Nominal voltage: 80 V Capacity: 1,376 Ah Voltage in idle state: 88.89 V Suitable for: Linde E70 and E80 Dimensions & Weight Dimensions (L x W x H): 1,290 x 1,030 x 770 mm Net weight: 2,500 kg All dimensions are approximate values. No guarantee is given for typographical or measurement errors. Nwedpfx Aoz S Nw Eog Rsn Collection conditions: Side loading up to 6 tons is possible with a large forklift truck on site. Loading is done at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons and up to a width of 230 cm. Collection is only possible after receipt of the payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. If collection is not carried out on time, a storage fee of €20 per machine per day will be charged. Outstanding storage fees must be paid in full before collection. Lot number: 1156

Condition: used, Year of construction: 2019, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Load capacity forklift: 2,500–5,000 kg Fork length: 1,350–2,000 mm Mounting: FEM 3A MACHINE DETAILS Nwsdpfx Agoz S Nwxo Rsn Dimensions & Weight Dimensions (L x W x H): 1,350 x 800 x 1,000 mm Net weight: 250 kg EQUIPMENT Hydraulic telescopic forks For loading onto a pallet for truck loading All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: Side loading up to 6 tons is possible using a large forklift on site. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons and up to a width of 230 cm. Collection is only possible after receipt of the payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. If collection is not carried out on time, a storage fee of €20 per machine per day will be charged. Any outstanding storage fees must be paid in full before collection. Lot number: 1103

Year of construction: 2005, condition: excellent (used), machine/vehicle number: 47885/05, pneumatic punching of window profiles stroke 20 mm Njdpfx Aeff Apisg Rewn

Condition: used, Year of construction: 2022, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS FEM class: FEM 3 Load capacity forklift: 3,000–5,000 kg Fork length: 1,350–2,350 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 1,350 x 1,000 x 1,000 mm Nwsdez S Nwlopfx Ag Rjn Self-weight: 200 kg All dimensions are approximate values. No guarantee is given for typographical or measurement errors. Collection conditions: Side loading up to 6 tons is possible using a large forklift on site. Loading is done at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of the payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. In case of delayed collection, a storage fee of €20 per machine and day will be charged. Outstanding storage fees must be paid in full before collection. Lot number: 1081

Condition: used, machine/vehicle number: 90540056, Year of construction: 2017, operating hours: 788 h, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Load capacity: 1,200 kg Lifting height: 2,500 mm Fork length: 1,150 mm MACHINE DETAILS Battery voltage: 24 V Battery capacity: 150 Ah Battery type: 2 PzB Dimensions & Weight Dimensions (L x W x H): 1,800 x 800 x 1,720 mm Own weight: 800 kg Service valid until: 07/2027 UVV certification valid until: 07/2027 Operating hours: 788 h EQUIPMENT Formerly a Jungheinrich full-service unit All dimensions are approximate values. No warranty is given for typographical or measurement errors. Collection conditions: Side loading up to 6 tons is possible with a large forklift on site. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of the payment confirmation by email. Collection without prior registration is possible from Monday to Friday between 07:00 and 16:00. If collection is not carried out on time, a storage fee of €20 per machine per day will be charged. Any outstanding storage fees must be paid in full before collection. Nodpfx Agsz S Nwfj Rewn Lot number: 446

Year of construction: 1984, condition: used, Corner connector, MachinePressta 7000, type PV 7. Nwedpfx Aji Dx A Eog Ron

Condition: used, machine/vehicle number: W41153L00104, Year of construction: 2022, operating hours: 3,050 h, load capacity: 2,000 kg, lifting height: 150 mm, fork length: 1,150 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Load capacity: 2,000 kg Lifting height: 150 mm Fork length: 1,150 mm MACHINE DETAILS Battery voltage: 24 V Battery capacity: 166 Ah Battery voltage in idle state: 25.3 V Dimensions & Weight Dimensions (L x W x H): 1,800 x 800 x 1,300 mm Own weight: 900 kg Operating hours: 3,050 h EQUIPMENT Folding platform Formerly a Linde full-service unit Nwsdpfoz S Nv Uex Ag Rsn All dimensions are approximate values. No guarantee is given for typographical or measurement errors. Collection conditions: Side loading up to 6 tons with a large forklift truck available on site is possible. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of the payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. If collection is not made within the specified time, a storage fee of €20 per machine and day will be charged. Any outstanding storage fees must be paid in full before collection. Lot number: 397