Injection Moulding Machine

KraussMaffei KM 160-1000 CX

Condition: excellent (used), Year of construction: 2012, Krauss Maffei KM 160–1000 CX Injection Moulding Machine 🔹 Basic Information Manufacturer: Krauss Maffei Model: KM 160–1000 CX Year of Manufacture: 2012 Operating Hours: 57,654 hours Category: Hydraulic Injection Moulding Machine 🔧 Clamping Unit Clamping Force: 1,600 kN (160 tons) Platen Dimensions: 820 × 845 mm Tie-bar Distance: 520 × 520 mm Minimum Mold Height: 300 mm Maximum Opening Stroke: 950 mm 💉 Injection Unit Screw Diameter: 50 mm Injection Volume: 432 cm³ Shot Weight: 393 g Injection Pressure: 2,304 bar ⚡ Electro-hydraulic System Pump Motor Power: 37 kW Heater Power: 18.7 kW Pedpfx Apsyv E E Dodorc 👉 Option to install Energy Saving System (ESS) – actual energy consumption reduction by up to 30–60% 📐 Dimensions & Weight Machine Weight: 9 tons Dimensions (L × W × H): 5.54 × 2.06 × 2.18 m

Condition: used, Year of construction: 2012, Technical details: max. wheel diameter: 260 mm gear width: 320 mm max. module: 5 weight of the machine ca.: 21 t dimensions of the machine ca.: 8,71 x 5,97 x 3,49 m no. of teeth: 1...999 max. helix angle: +45/-45 ° pitch min.: 0,1 mm pitch max.: 1000 mm Prjdpfoy Amllox Apdec X-axis: 345 mm y-axis: 250 mm Z-axis: 320 mm b-axis: 360 ° c-axis: 360 °

Condition: used, Saw BEHRINGER HBE 321 A Dynamic Prsdpfox Tvkxjx Apdjc

Condition: excellent (used), Year of construction: 2008, Injection molding machine BATTENFELD HM 60/350 S Year of manufacture: 2008 Injection elements: Pedpfx Ask Rnq Nspdorc Screw diameter: 35 mm Injection weight : 153.8 g Injection pressure: 2083 bar Injection volume: 169 ccm Closure elements: Closing force : 60 t Clearance between columns: 370x320 mm Dimensions of table plates max: 550x530 mm Ejector: hydraulic Closing system: hydraulic Control: UNILOG B6 Additional equipment: Machine in very good technical condition Euromap 67 Dimensions: Weight: 3100 kg Length/Width/Height: 3.79x1.24x1.88 m Power supply: Pump/motor: 15 kW Heaters: 10.4 kW Total: 25.4 kW

Condition: good (used), Year of construction: 2019, Universal machining center Machine type: Hedelius Acura 65 Control: Heidenhain TNC 640 Year: 2019 Available after: Dezember 2026 SPECIFICATIONS 5-axis-simultaneous X-Axis: 700 mm Y-Axis: 650 / 465 mm Z-Axis: 600 mm Rapid motion: (X/Y/Z): 40/40/40 m/min. B-Axes: +30° / -115° Spindle speeds: 12.000 rpm Spindle power: 22 kW Torque: 117 Nm Tool: SK 40 Tool capacity: 65 Table size: D: 650 x 540 mm mm Max. Table Load: 500 kg Equipment Chip conveyor 3D-Touch probe: M&H Internal cooling: 25 bar Cooling tank: 500 l Electronical handwheel: HR 510 Oil mist separator Chip rinsing pistol Prsdpez D Aq Ujfx Apdsc Kinematikset 3D-Formenbauabstimmung Documentation - German

Year of construction: 1999, condition: ready for operation (used), Max. clamping force: 500kN, opening stroke: 350mm, tool installation height: 200mm, heating output: 6.5kW, screw diameter: 40mm, weight: 2.33t, no documentation available. Pjdpfjilhfcjx Apderc

Condition: excellent (used), Year of construction: 2019, Swing 806mm, Swing over cross slide 527mm, maximum cutting diameter 457mm, 762mm between centres, 584mm maximum cutting length, 0.01 degree C axis, 3000rpm Milling 3.7kW, +/- 50mm Y axis, 76mm Bar capacity, 22.4kW Spindle Motor, 3400rpm spindle, Prsdpfxezg Efio Apdec 24m/minute rapid feedrate, 24 Station turret, swarf conveyor, tailstock, tool setter, coolant,

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036946, clamping force: 800 kN, screw diameter: 40 mm, displacement volume: 201 cm³, injection pressure: 1,860 bar, injection weight: 183 g, mold height (min.): 150 mm, ejector force: 22,000 N, ejector stroke: 100 mm, opening stroke: 750 mm, installation height: 400 mm, total length: 4,750 mm, total width: 1,670 mm, total height: 1,850 mm, overall weight: 5,600 kg, heating capacity: 11.5 kW (15.64 HP), drive type: Vollelektrisch, clear span: 735 mm, tool weight: 600,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The basic injection molding machine, precisionMolding, offers the perfect entry-level solution for all-electric injection molding, enabling you to react quickly and innovatively to market requirements. It combines high performance, simple operation and short delivery times. It can be used in a wide range of applications, e.g. in the packaging industry, the electrical and electronics industry, medical technology and the automotive industry. Your benefits: - Optimized price-performance ratio for a wide range of applications - High energy efficiency thanks to all-electric machine concept - Realization of demanding delivery times thanks to basic machine concept with a wide range of options TECHNICAL DATA: KM 80 / 380 PA G01 (order 38670023) CONTROL  MC P1 with 15" TFT color screen with multi-touch functions CLAMPING UNIT  Clamping force kN 800  Mold opening force, max kN 120  Clear width (h x v) mm 470 x 420  Clamping platen (h x v) mm 610 x 560  Tool installation height min. - max. mm 150 - 400  Opening width mm 750  Mold opening stroke max. mm 350  Ejector drive electric  Ejector stroke mm 100  Ejector force forwards/backwards kN 22 / 22  Ejector speed forwards/backwards mm/s 300 / 300  Max. Mold weight kg 600 SPRING UNIT  Screw diameter / type mm 40 / standard  Effective Ls/D ratio 20.0  Injection pressure bar 1860  Stroke volume cm³ 201  Shot weight at max. stroke for PS g 183  Injection speed mm/s 200  Injection flow rate cm³/s 251  Screw drive/speed 1/min 334  Plasticizing flow (standard) g/s 24.7  Nozzle contact force kN 34 ELECTRICAL PARAMETERS  Connected load kW 20.6  Installed heat output kW 11.5  Power supply V / Hz 400 / 50 3 phases with neutral conductor WEIGHT AND DIMENSIONS  Net weight with switch cabinet t 5.6  Length x width x height m 4.75 x 1.67 x 1.85 ADDITIONAL EQUIPMENT  Low-wear plasticizing  BluePower fully insulated plasticizing cylinder  Open nozzle  Air valve 1 - fold (BWAP)  Pneum. Control hot runner valve gate 1 - compartment  Electrical interface cascade 4-fold  Euromap interface handling E18, E63  Euromap interface (central computer) E67, E77  Water battery 4 - compartment  Automatic central lubrication  Adaptive Process Control (APC)  Spray embossing circuit  Graphic analysis package The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. Podpfxjud H Dmo Apdsrc We look forward to your inquiry.

Condition: good (used), Year of construction: 1999, operating hours: 95,239 h, functionality: fully functional, machine/vehicle number: 173937, clamping force: 2,000 kN, screw diameter: 55 mm, clearance between the columns: 520 mm, mold height (min.): 250 mm, total length: 5,100 mm, total width: 1,800 mm, total height: 2,200 mm, overall weight: 6,630 kg, Equipment: documentation/manual, The machine ran perfectly until the last day before the new machine was delivered to us. The machine is therefore in good used condition. Due to a lack of space in the injection molding shop, the machine is being sold and is no longer powered. The pump / injection unit / clamping unit are sealed. The machine manual is available Prsdsv D Nxljpfx Apdsc Videos of the machine are available Pump operating hours: 95239 Automatic operating hours: 86082 Repairs from recent years: Filter replaced annually 05/2024 Fan in the control cabinet replaced 07/2023 New valve for Y201 and Y210 nozzle forward/backward 02/2023 New keypad installed. Field with motor and heater 12/2022 Ejector sealed. Injection unit sealed including new piston

Condition: as good as new (ex-display), Year of construction: 2026, Compact wide-belt sanding machine with combination sanding unit Prodpfxogf Sw No Apdsc Promotional features: - Switching the sanding pad on and off from the control panel - Switching the roller on and off from the control panel - Electronic control system Fox 500 KTR - Table extension with 2 rollers, with infeed and outfeed - Automatic table positioning with push button Article number: 5222100A2 Also suitable for smaller workshops for occasional use Combination sanding unit with sanding pad for fine sanding Standard equipment includes a diagonally grooved steel roller, Ø 120 mm, for calibrating Fine adjustment of the working height Clear control panel on the front Robust, tubular-reinforced monoblock steel machine body, robot-welded, with work units mounted high up for maximum rigidity Motorized height adjustment of the work table with digital display Electronically controlled sanding belt oscillation Carpet feed via geared motor with two speeds Natural rubber feed carpet with a negative profile Flexible steel pressure bar in front of the first unit Rubber pressure rollers, in front of or behind each work unit Pneumatic belt tensioning per unit with decimal correction option for grit size/belt thickness Universally applicable for solid wood and veneer thanks to the combination unit Entry-level model for smaller companies Working width 950 mm Equipment details: Combination unit for calibrating and sanding Diagonally grooved steel roller, Ø 120 mm, with fine height adjustment Hard sanding pad with graphite pad Universal design for calibrating and sanding solid wood, chipboard and veneer Technical data Length (product) approx. 1388 mm Height (product) approx. 1668 mm Width/Depth (product) approx. 1545 mm Connection for dust extraction Dust extraction nozzle diameter 140 mm Electrical data Connection voltage 400V Current type AC Phase(s) 3Ph Mains frequency 50Hz Power feed motor 0.33 / 0.55 kW Power height adjustment motor 0.25 kW Power drive motor 7.5 kW Sanding unit Sanding belt length 1525 mm Sanding width max. 950 mm Sanding belt width 970 mm Feed unit Feed speed 4.5 / 9 m/min Workpiece Workpiece height min. 4 mm Workpiece height max. 170 mm