2024 KRAUS MAFFEI KM PA 250/1400 PA G01

KRAUS MAFFEI KM PA 250/1400 PA G01

Condition: new, machine/vehicle number: Baureihe GSL 300 / Neumaschine, The cutting mills in the GSL series 300/400 to 300/800 are primarily intended for the shredding of production-related scrap material in the injection molding and blow molding sectors. In addition to the key advantages of the GSL series, the slow-running cutting mills GSL 300/400, GSL 300/600 and GSL 300/800 are particularly suitable for large-area parts, such as car door panels, bumpers or hollow bodies. The "V-arrangement" of the rotor blades keeps the pre-shredded material in the center of the rotor. This significantly reduces wear on the grinding chamber walls when grinding glass fiber reinforced plastics. Material sticking to the side walls is avoided. The staggered arrangement of the rotor disks means that only individual blades are used at any one time, so a higher cutting force is available in each case. Kwodjghgbhepfx Ad Not

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Kwsdswu Tu Dspfx Ad Njt Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: used, Year of construction: 2019, Year: 2017 Control type: CC300 Number of hours: 20,000H Storage location: MECA PLASTIC Deadline: AVAILABLE Closing force: 160 T Opening stroke: 460 mm Between columns: 520 mm x 520 mm Plate dimensions: 760 mm x 760 mm Minimum/maximum mold: 250/600 mm Maximum spacing between plates: 1060 mm Screw diameter: 35 mm Screw length: 20T cm3: 154 Ksdpfsv I Uw Iex Ad Nswt Bars: 2000 Motor power: 21 kW Heating power: 9.2 kW Closing weight: 8.4 T Length dimensions: 5.90 m Width dimensions: 1.70 m Height dimensions: 2.20 m Cores: NO Robot interface: YES Bi-metal: YES

Condition: excellent (used), Year of construction: 2016, operating hours: 23,170 h, clamping force: 2,500 kN, screw diameter: 60 mm, injection pressure: 2,005 bar, injection weight: 618 g, mold height (min.): 330 mm, Injection molding machine Krauss Maffei 250-1400CX with robot and gas boost (225) Product Code: 225 Availability: In Stock Year of production: 2016 Brand: KRAUSS MAFFEI Technical data Shot Weight: 618 g Injection speed: 848 ccm/s Kodpfxevtzkfo Ad Nswt Clamping Force: 2,500 kN Screw dia: 60 mm Injection pressure: 2005 bar Tie bar distance: 630x630 mm Platen size: 1135x1180 mm Mould height min.: 330 mm Total day-light max: 1150 mm Type of controls: MC6 Language: German Power: 70 kW Workinghours: 23170 h Weight: 15000 kg Dimensions: 6,5x2,3x2,3 m Hopper: No Core pull: Yes Euromap: Yes Air valve: Yes Heating channels: Yes Gas bottle: Yes Picker or robot: Yes

Condition: good (used), Year of construction: 2006, Vertical Machining Center Machine type: DMG DMC 635 V Control: Heidenhain iTNC 530 Year of manufacture: 2006 TECHNICAL DATA: Travel distances: X-axis: 635 mm Y-axis: 460 mm Z-axis: 510 mm Rapid traverse (X/Y/Z): 30 / 30 / 30 m/min Kwjdpswzanwefx Ad Not Speed range: 20 - 10,000 rpm Spindle motor: 9 / 13 kW Tool holder: SK 40 Tool changer Tool positions: 20 Table size: 790 x 560 mm Max. table load: 600 kg Features: Chip conveyor Electronic handwheel Chip wash gun Operating mode: 4

Condition: excellent (used), Year of construction: 2011, operating hours: 28,000 h, functionality: fully functional, clamping force: 1,300 kN, For sale is a hybrid injection molding machine, 2 components, of the brand KraussMaffei and type KM 130-750 CX The machine is in very good condition, ready for immediate use, with low operating hours. Electronic injection unit and dosing unit, hydraulic clamping unit. Technical data: Year of construction: 2011 Operating hours: 28,000 h Clamping force: 130 T Kwsdpfeu Hxm Uox Ad Not Cylinder Ø 30mm / 40 mm (& 2*50mm additional) Core pull: 1*Hydraulic Valve gate: Pneumatic Tie bar extension: 160 mm Internal pressure transducer Selector switch On request, transportation and loading can be organized at an extra charge. can be organized throughout Europe. Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036721, clamping force: 6,500 kN, screw diameter: 70 mm, clearance between the columns: 1,110 mm, displacement volume: 1,078 cm³, injection pressure: 1,877 bar, injection weight: 981 g, opening stroke: 3,200 mm, plate height: 1,540 mm, drive type: Hydraulisch, clear span: 3,200 mm, tool weight: 2,200,000 g, Injection Moulding Machines Directly from the Manufacturer! As the manufacturer KraussMaffei, we offer you our certified and flexible stock machines: The hydromechanical two-platen clamping unit of the GXW machine sets new standards in terms of quality and productivity. With the sophisticated GuideX sliding shoe, forces are ideally absorbed and the service life of the moulds is extended. The innovative GearX locking system engages instantly and reliably. Powerful, user-friendly and value-retaining. TECHNICAL DATA: Kwodpfx Adjw U N Ixs Njt KM 650 / 2000 / 2000 GXW G06 (Order 38618339) CONTROL SYSTEM - MC 6 with 24'' TFT color screen with multitouch functions CLAMPING UNIT - Clamping force: 6500 kN - Max. mould opening force: 455 kN - Daylight opening (h x v): 1110 x 960 mm - Platen size (h x v): 1540 x 1440 mm - Mould installation height min. - max.: 1550 mm (without centre platen) - Opening stroke: 3200 mm - Max. mould opening distance: 1650 mm - Max. mould weight: 22,000 kg INJECTION UNIT 1 SP2000 - Screw diameter / type: 60 mm / thermoplastics - Effective L/D ratio: 23.3 - Injection pressure: 2420 bar - Shot volume: 792 cm³ - Shot weight at max. stroke for PS: 720 g - Injection speed: 140 mm/s - Injection throughput: 396 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 72.2 g/s - Nozzle contact force: 82 kN INJECTION UNIT 2 SP2000 - Screw diameter / type: 70 mm / thermoplastics - Effective L/D ratio: 20 - Injection pressure: 1877 bar - Shot volume: 1078 cm³ - Shot weight at max. stroke for PS: 981 g - Injection speed: 140 mm/s - Injection throughput: 539 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 98.3 g/s - Nozzle contact force: 82 kN ELECTRICAL PARAMETERS - Connected load: 341 kW - Power supply: 400 V / 50 Hz, 3 phases with neutral conductor WEIGHT & DIMENSIONS - Net weight: 43.5 t - L x W x H: 11.89 x 3.22 x 2.77 m ADDITIONAL EQUIPMENT - Wear-resistant plasticizing unit - BluePower full insulation for plasticizing cylinder - Open nozzle - BluePower ServoDrive - Pneumatic valve: 1-fold (BWAP), 1-fold (FWAP) - Pneumatic cascade valves: 6-fold (BWAP), 6-fold (FWAP) - Hydraulic core pull: 2-fold (BWAP), 2-fold (FWAP) - Mould heating: 96 zones (3.5 kW each) - Euromap interface for handling: E18 - Euromap central computer interfaces: E67, E77, E78, E63, E82.1 - Adaptive Process Control (APC+) - Graphic analysis package - Sliding table with turning unit, servo-driven - Vertical centre platen - Parallel clamping & opening during injection process with bar parallelism control between FWAP and centre platen or BWAP and centre platen - ColorForm interface signal interface for connecting an RPM unit - Electrical interface for HRS-Flexflow system - Electrical interface and hydraulic valves for "1-K dummy operation" - Interface for connecting a CoMo-Kistler Injection Basic System with good/bad part separation The machine is located at our plant in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your enquiry.

Condition: excellent (used), Year of construction: 2019, operating hours: 12,188 h, functionality: fully functional, machine/vehicle number: 233832, clamping force: 1,200 kN, screw diameter: 40 mm, mold height (min.): 300 mm, ejector stroke: 130 mm, opening stroke: 507 mm, plate length: 680 mm, plate width: 740 mm, total length: 4,854 mm, total width: 1,508 mm, total height: 2,503 mm, overall weight: 6,800 kg, pressure: 1,300 bar, type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, ENGEL VICTORY 500/120 SPEX injection molding machine, 2019, 120T, ECODRIVE, CC300, 12188 h For sale: ENGEL VICTORY 500/120 SPEX injection molding machine in excellent working condition. The machine has been used in a single production facility, regularly serviced and maintained, fully operational and ready for immediate use. Technical details: Year of manufacture: 2019 Operating hours: 12 188 h Clamping force: 120 tons Type: tie-barless Mounting plate with centering hole Ø125 mm Central ejector 12 heating zones for hot runner (Euromap 14), up to 22 kW total power Sliding hopper base Bimetallic barrel Screw type S8, GPS (G1), Ø40 mm, L/D 20 Non-return valve UNR9 (R9B) Ceramic heating elements ECODRIVE hydraulic package – SHV1 CC300 controller (languages: Polish, English) Ecograph, IQ weight monitor Power supply: 3x400V + N + PE / 50Hz 4-fold rotameter Contactless position sensors 4 programmable digital inputs and 4 outputs Piovan S52 material loader (150 kg/h) Weight: 6 800 kg Condition: For sale: ENGEL VICTORY 500/120 SPEX injection molding machine in excellent working condition. The machine has been used in a single production facility, regularly serviced and maintained, fully operational and ready for immediate use. Technical details: Year of manufacture: 2019 Operating hours: 12 188 h Clamping force: 120 tons Kwjdjxmu N Dopfx Ad Njt Type: tie-barless Mounting plate with centering hole Ø125 mm Central ejector 12 heating zones for hot runner (Euromap 14), up to 22 kW total power Sliding hopper base Bimetallic barrel Screw type S8, GPS (G1), Ø40 mm, L/D 20 Non-return valve UNR9 (R9B) Ceramic heating elements ECODRIVE hydraulic package – SHV1 CC300 controller (languages: Polish, English) Ecograph, IQ weight monitor Power supply: 3x400V + N + PE / 50Hz 4-fold rotameter Contactless position sensors 4 programmable digital inputs and 4 outputs Piovan S52 material loader (150 kg/h) Weight: 6 800 kg Condition: excellent, available for inspection and test run. Location: Hajnowka, Podlaskie, Poland

Condition: excellent (used), Year of construction: 2013, overall weight: 540 kg, volume flow: 310.8 m³/h, pressure (max.): 8.5 bar, Equipment: type plate available, PROD. ATLASCOPCO TYPE - GA30 S/N - API324380 YEAR - 2013 POWER (kW) - 30 PUMP (m3/min) - 5.18 Kodsqfd U Iopfx Ad Njwt CIS (bar) - 8.5

Condition: ready for operation (used), Year of construction: 2019, operating hours: 34,573 h, General Data Machine weight 2200 kg Ksdpex Nkn Rjfx Ad Nswt Measurements height 2240 mm Dimensions Machine Length 7200 mm Injection Unit Screw diameter 80 mm Clamping Unit Clamping force 4500 kN This HAITIAN JU4500II was manufactured in 2019. It features a clamping force of 4,500 kN, a maximum injection volume of 1,239 cm³, and a screw diameter of 80 mm. The machine includes a robot interface (Euromap 67) and is still in production with excellent condition. If you are looking to get high-quality injection moulding capabilities, consider the HAITIAN JU4500II machine we have for sale. Contact us for more information about this machine. Application Types Injection Moulding