Folding Machine - SBS E 2540/1,5

Knuth SBS E 2540/1,5

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. Nodpfxowu Tu Ds Ahvjku - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: used, Year of construction: 1986, plate thickness 6,0 mm pressure 18 t cutting angle - upper blade 90 ° blade length 225 x 225 mm voltage 380 V total power requirement 5,5 kW weight of the machine ca. 650 kg dimensions of the machine ca. 1,10 x 0,80 x 1,05 m Nsdpjg Ip Efsfx Ahveku - Angular stops adjustable

Condition: new, Year of construction: 2025, Capacity 2020 x 2 mm (ST37) Delivery of the upper beam by hand lever left + right Slanted segments in the upper beam Continuous bending and lower beam rails RAL 7016 paint Manufacturing EU immediately available ex works Freight costs on request Nksdpfx Ahefifa Aoveu

Condition: new, functionality: fully functional, Year of construction: 2025, Box Type Electrostatic Powder Coating Oven: Length: 500cm, Width: 250cm, Height: 300cm - Powder Coating Booth with Filter: Length:300cm, Width:220cm, Height:270cm Nksdpfx Ahsv Nvndevou - Electrostatic Powder Coating Equipment: Model: HMK MULTICOLOR, Type of Use: Manual

Condition: new, Year of construction: 2025, Entry-level sheet fiber laser metal cutting machine Lower laser cutting cost and easy operation The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Nsdshv U U Dspfx Ahvoku Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Condition: New Laser Type: Fiber Laser Laser Power: 1000W, 1500W, 2000W, 3000W Cutting Area: 3000*1524mm Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Cutting Speed: 0-100m/min Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: good (used), Three-phase motor, electric motor -Power: 5.5/8/22 kW -Speed: 740/975/1475 rpm -Shaft: Ø 55 mm -Construction: B3 -Protection class: IP 33 -Dimensions: 750/510/H390 mm Nedpfed E Tfnex Ahvjku -Weight: 275 kg

Condition: new, Year of construction: 2025, Bending machine PROD-MASZ to the plate ZGR 2640/1.2 is a sensational machine for precision bending of all types of metal sheets (steel 1.2mm, titanium zinc 1.2mm, aluminum of 1.5 mm, copper sheet 0.8 mm). Equipped with a rack supporting plate, two front bumpers, bending angle measurement, a single lock of bending angle, turnbuckles, eccentric mechanisms. Each part of the machine is adjustable, which allows for adjustment of the arc bending. Used in the device locking system (set by the operator) allows you to achieve the desired angle of bending. Table rear and front bumpers are made of galvanized racks. Ideal for all kinds of steel treatments - wherever the roof is exposed to moisture infiltration. Proper execution of these connections certainly prolong the life of the roof. By hers construction she can be used not only for bending panels with both the ferrous metal, sheets of plastic and fiberboard. - Max. bending angle: 145 degrees Njdpfx Aodad Adshvsku - Rotary shears cut to full working length - Thickness of bending bar: 24 mm - Protractor - Weight: 350 kg Rotary shears (max. plate gauge 0,8 mm / Steel) + 350 Euro - The machine have certificate CE and 12 months warranty. Only shipping is possible Delivery every week Price excl. shipping We provide invoices with 0% of tax.

Condition: new, Year of construction: 2025, DON'T WAIT ANY MORE AND ORDER YOUR MACHINE We offer you a wide range of sheet metal bending machines and guillotine shears. What you can expect from us: fast and safe delivery without complications; competent advice and service during the guarantee period and afterwards. Promised. Advice, delivery or maintenance? It's a pleasure. For individual machines or entire packages? No problem. We know all our devices inside and out. For years. And as a manufacturer, we are always up to date. We look forward to you. Bending machine 3.14m/0.8mm Technical specifications: - maximum working width: 3140 mm - Bending capacity: up to 0.8 mm (steel sheet) - Bending angle: max 145 degrees - Bending beam thickness: 24 mm - the cut with the roller shears over the entire working width - lifting of the upper beam in three positions - Passage opening: 80 mm - degree scale - angle stop - Front and depth stops - Weight: about 400 kg - The roller scissors (max. cutting capacity up to 0.8 mm / sheet steel) plus 350 euros - The machine complies with CE guidelines and has a 12-month guarantee. Price: €2050.00 Njdpfscka Suox Ahveku The delivery costs are: €330.00 Cash on delivery Delivery within 4 days from order date We are looking forward to your contact! Invoices are issued with 0% as intra-community delivery

Condition: good (used), Hook type shotblasting machine 250 kg TOSCA TS-250 Type: Hook type Max. diameter of workpiece: 1000 mm Max. height of workpiece: 1500 mm Max. workpiece weight: 500 kg Machine oppening width: mm Nr. Of turbines: 2 Turbine type: 360 Turbine wheel diameter: 360 mm Power of turbine: 7,5 kW Max. turbine flow: 105 kg/min Type of transport rail: Y Cleaner type: airwash Foundation: no Housing protection: Mn+ rubber Req. air flow: 3.000 m3/h Max. installed power: app. 19 kW Total weight of machine: 0 kg Total width of machine: mm Total height of machine: mm Total length of machine: mm Njdpevpgq Nofx Ahveku Machine is in the process of full refurbishment. All components that are damaged will be replaced with new, turbiness fully reconditioned, new color RAL 7037/2000..... Machine will be dellivered in condition comparable AS NEW. !!! AS NEW CONDITION !!!

Condition: used, Year of construction: 1980, machine/vehicle number: xxxx, Lg.no. 24211 Technical data approx: - max. working width 1020 mm Nedpfst H I Aqsx Ahvsku - max. material thickness at 40 kg/mm² strength 1.5 mm - man. back gauge adjustable up to 550 mm - front angle stop - sheet hold-down device - Table size 1100 x 650 mm - Working height 900 mm - Space requirement approx. W 1800 x H 1450 x D 850 mm - Weight approx. 400 kg - mobile