SCHLATTER MESH WELDING LINE MG 24.1/8CSCHLATTER
MESH WELDING LINE MG 24.1/8C
Machine data
- Machine type:
- SCHLATTER MESH WELDING LINE MG 24.1/8C
- Manufacturer:
- SCHLATTER
- Condition:
- refurbished (used)
Price & Location
- Location:
- Madrid, Spain
Details about the offer
- Listing ID:
- A19429911
- Reference number:
- 4056
- Update:
- 25.06.2025
Description
Full revamped
WORKING RANGE
Panel width: max. 2500 mm
Weft wire length: min. 900 mm
Weft wire length with QF5 dispenser: min. 300 - 1600 mm
Spacing between extreme warp wires: max. 2400 mm
Mesh length (warp wire length): max. 2500 - 6000 mm
Spacing between warp wires: min. 100 mm
Spacing between weft wires: 25-250 mm
Adjustable by cutting device (0-1)
Warp wire diameter: 4.0 - 12.0 mm
Weft wire diameter: 4.0 - 12.0 mm
Number of warp wires: max. 24
WELDING MESH MACHINE MG 24.1/8C, Basic equipment including:
- 1 Machine frame
- 1 Upper support for press reception, continuously adjustable by hand crank
- 1 Magnet supports with retaining magnets and weft wire monitoring.
- 1 Row of pneumatic solenoid valves for press actuation.
- 1 Installation for air and water.
- 2 Pneumatic rotary drives with oil damping
- Static motor torque with 5 bar compressed air: 480 Nm
- Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1)
- 1 Advance carriage with panel lifting device
- 1 Set of tools for machine adjustment
WELDING SECTION
8 Type C Transformers
Rated power of each transformer: 100 kVA
No-load secondary voltage: 7.1 V
Rated secondary current: 14 kA
8 Thyristor contactors ES 130
Fjdpfx Afewu Tu Denspb
12 Welding presses: 5.0 kN
12 Chain current bridge for spacing of warp wires: 50-100 mm
12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm
10 Chain current bridge for spacing of warp wires: 100-150 mm
8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm
6 Chain current bridge for spacing of warp wires: 150 - 200 mm
6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm
24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm
24 Wire clamping pliers
Panel width: max. 2500 mm
Weft wire length: min. 900 mm
Weft wire length with QF5 dispenser: min. 300 - 1600 mm
Spacing between extreme warp wires: max. 2400 mm
Mesh length (warp wire length): max. 2500 - 6000 mm
Spacing between warp wires: min. 100 mm
Spacing between weft wires: 25-250 mm
Warp wire diameter: 4.0 - 12.0 mm
Weft wire diameter: 4.0 - 12.0 mm
Number of warp wires: max. 24
Seller
Registered since: 2022
Send inquiry
Telephone & Fax
Liverpool CentauroAlfa Jamb
Tauberbischofsheim HymmenCombiCoater ELX-S 1400
Ennepetal CHICAGO PNEUMATICCPVR15 + Lufttrockner
Königsbach-Stein PowasertADS SE 1
Maastricht 
Kežmarok RapidDGS
Roreto MASTERWOOD + AMSMultitec + Teknomat 3000
Wuppertal AlpahtecA-ES 75.28 V
Heiligenhaus KUKA Industrieroboter Lineareinheiten 8mKUKA KR180 R2900 KRC4 Linearachse 8m
Đakovo VITARINR 350 E
Machineseeker Trust Seal
What is the trust seal?
Machineseeker certifies selected sellers with the Machineseeker trust seal. Before approval, a standardized and comprehensive check is carried out by experienced Machineseeker staff.
What do we verify?
Check of
trade licence or commercial register extract
Verification of the dealer's
postal address
Validation of the
banking details
Verification of
accessibility to
main phone number
Credit report
may not contain negative criteria
Buyer complaints
can lead to withdrawal of the sealWhat does this mean for you as buyer?
The Machineseeker trust seal enables you, as a buyer, to identify trustworthy sellers who are very likely to do honest and righteous business, without having to do your own investigation.
Disagreements may of course still arise during the purchasing process. Machineseeker is not liable for any legal violations by buyers or sellers active on Machineseeker.