Recoiler - mandrel 0,5 t

KEMMERICH

Condition: excellent (used), functionality: fully functional, Year of construction: 1999, Coil weight: 150kg Strip witdh: max. 100mm Outer diameter: max. 1.200mm Inner diameter: 320 ... 520mm Lhsdpfx Aoh T Ducjfasf Performance • decoiler fixed on moveable frame • Disc on back side and ring on front side for lateral coil keeping • manual adjustable brake

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Lhedpjkvnumsfx Afaof Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: ready for operation (used), A complete punching system with a grid punch is available. 1) Reel Gebrüder Kemmerich 7VID, year of manufacture: 1981, max. load: 1000kg. 2) Straightening machine, max. material width: 300mm, max. material thickness: 2mm. 3) Feed unit Alba UVHY 300/0.1, feed speed: 6.5m/min, max. material width: 300mm, max. material thickness: 4mm, transport rollers: 2. 4) Punching grid HR 50/600 NL, stroke rate: 300/min, stroke: 30mm-80mm. On-site inspection is possible. Ljdpjw Az R Aefx Afaehf

Condition: used, Pay-off and Take-up Decoiler KEMMERICH / STANGE Type HA 1500 / 500 Serial No. 51673 Year of Manufacture: 2023 (unused) Ljdpoua Nngsfx Afashf Maximum coil weight: 1500 kg Coil width with guide arms: 500 mm Coil width without guide arms: 670 mm Coil inner diameter: 300 - 370 mm Coil inner diameter with extension jaws: approx. 380 - 440 mm Decoiler turntable diameter: Ø 2080 mm Coil outer diameter without pressure arm: max. 2350 mm Coil outer diameter with pressure arm: max. 2200 mm Center of turntable to decoiler base: 1200 mm Decoiler shaft, support shaft: Ø 70 mm Speed: approx. 1.5 to 20 rpm Motor power: 1.1 kW Power supply: 400 Volt, 50 Hz - stepless turntable speed adjustment via frequency converter - loop switch / proximity switch for decoiler STOP - central expansion via hand crank - clockwise and counterclockwise rotation - pneumatic pressure arm with running roller - 4 guide arms, 870 mm each - 4 plastic extension jaws for adapting the turntable Space requirement (L x W x H) Weight: 970 kg Very good condition

Condition: new, Year of construction: 2025, Single band console decoiler 500 mm - Loading capacity 1.500 kg - Inner φ 480-530 mm - with 4 clamping arms, ball bearings and with disc brakes - max coil width: 500 mm Lhodpfx Afjfvbxqjasf

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable. Ledpfx Aeg U Utvofaehf

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet Lodpfx Aehlnzkefajhf - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Year of construction: 1987, condition: used, sheet width 150 mm coil weight 80 kg coil external diameter 650 mm Lhjdpfx Afefn Aqljasf 1000 mm diameter of the mandrel 230 - 445 mm total power requirement kW weight of the machine ca. t dimensions of the machine ca. m

Condition: new, machine/vehicle number: 246203 xxxx, functionality: fully functional, Ideal basis for setting up CNC machines and applications The FB2 flatbed unit is ideal for getting started with CNC technology and is ideal for model making and hobby applications. The FB2 is also often used in industry for measuring and dosing technology, as it offers extensive expansion options. The unit also offers access to the isel modular system. Various sizes from travels of 530 x 500 mm to 1030 x 1250 mm and extensions such as base frame and housing are available and can be individually combined. BEST SUITABLE FOR: • modular isel building block system • universal range of applications • easy handling • ideal for laboratory, model making and workshop use • assembly and mounting • printing and engraving • drilling and milling • dosing and screwing • forming and modeling • gluing and casting • soldering and welding • measuring and testing • sawing and cutting and much more Z-passage = 190 mm (Z-passage = 300 and 500 mm on request!) FEATURES: Lodpfx Afshqmamjaohf • durable stepper motors in the 200 W range • reliable LES units with steel ball screws are installed as drives • clamping of workpieces using a T-slotted plate • available with and without protective cover • variable gantry apertures, depending on customer application OPTIONS: • iSA milling spindles and water-cooled HF milling spindles • Cooling spray device • Cold air cooling, Cool-Min • Automatic tool length measurement • Rotation units • Workpiece clamping systems (hand lever, vacuum clamping tables, etc.) • Suction systems • LED machine room lighting • RAL color selection • CAD/CAM-Software • Diffusers 190 mm, 300 mm or 500 mm • Powerful 4-axis control controller • Underframe • Enclosure with sliding/folding door

Condition: ready for operation (used), Year of construction: 1980, Power: 300 to Size of bolster: 1.200 x 850 mm Overhang: 400 mm Width of ram: 1.100 mm Opening in bolster: 400 x 250 mm Daylight: 500 mm Frequency: 32 1/min Lhodpfxsd A Hbce Afasf Stroke: 30 - 140 mm Ram adjustment: 105 mm Weight: app. 19.500kg Other - allowed for 2-Hand safe working - euqipped by safety valve Herion Xsz 20 - Motorized grease lubrication - Pneumatic ram balancing cylinders - Motorized ram adjustment - T-slots in ram - Stand alone control panel - bearing of con rod overhault