Rotary table

KAMA KURA

Condition: good (used), Year of construction: 1981, functionality: fully functional, SINGLE-DIE TUBULAR RIVET HEADER NATIONAL M5 Rebuilt on 2024. New electrical system. Operational, working. Available for any test. Number of die: 1 Number of pieces per min.: 300 Length Rivet: 20 mm. Depth of Pierce (max.): 5 mm. Cutoff diameter: 5 mm. Floor space (width): 1.300 mm. Dcedpfx Astxni Noc Hok Floor space (length): 2.690 mm. Power of main motor: 7.5 KW Net weight: 3.100 kg. Gross weight: 3.700 kg.

Condition: new, Year of construction: 2026, Miter saw and cut-off saw, type: ZS 200 N - 5 KW motor with machine stand, but without saw blade Machine operated via handwheel and worm gear (rear) Tilting Saw blade diameter: 520 mm, saw blade arbor bore: 50 mm Saw blade speed: 2800 rpm 400 volts / 5 KW (S6/40%) motor with brake and automatic star-delta motor switching Cutting width at 90 degrees: 420 mm Cutting width at 45 degrees: when tilted: 295 mm Cutting height at 90 degrees: 200 mm Cutting height at 45 degrees when tilted: 140 mm The saw can be tilted to an acute angle of approximately 25 degrees on one side and tilted flat to the left up to 30 degrees. Dodpfx Acoi Dfido Heck Machine weight: approx. 250 kg Location: Available from stock in 54634 Bitburg - immediately available -

Condition: used, Year of construction: 2005, x-travel 600 mm y-travel 500 mm z-travel 600 mm control iTNC 530 Heidenhain table surface area 900 x 500 mm spindle turning speed - stepless 0-12.000 U/min spindle drive 10 kW tool taper SK40 DIN 69871 tool magazin: 24 total power requirement 22 kW weight of the machine ca. 6,4 t dimensions of the machine ca. 5,3 x 3,5 x 3,5 m Chip conveyor scraper belt Coolant system 3 pumps / cartridge filter Grundfoss high-pressure pump type CRK2-220/22 A-W-A-AUUV Dedpfx Ajvxwq Esc Heck

Condition: used, machine/vehicle number: 1 284 066, Feed diameter: 200 mm Through-hole: 50 mm Mounting, short taper according to DIN 55027: Size 6 Outer diameter of the clamping cylinder: 290 mm Overall height (clamping cylinder to the front of the chuck, without jaws): 150 mm pneumatically actuated Dcodpecm Tgksfx Ac Hjk

Year of construction: 1993, condition: good (used), machine/vehicle number: 86317, Offer 25335 Technical specifications: - Nominal / continuous temperature, stepless: up to 1280 °C - Three-sided heating (bottom and sides) Dodpfxex D U Eys Ac Hock - Temperature control via NABERTHERM Controller C 19 - Drive: 400 V / 5.5 kW - Internal dimensions approx.: W 250 x H 140 x D 350 mm - Usable volume: 11 L - Base frame: W 900 x H 900 x D 950 mm - Required space approx.: W 800 x H 600 x D 750 mm - Weight approx.: 80 kg

Condition: used, Year of construction: 1993, Technical details: tube diameter: 80 mm tube diameter min.: 6 mm control for program: Gelma MM-1 tube pipe draw up length: 1800 mm weight of the machine ca.: 0,232 t dimension machine xH: 1,9 x 0,7 x 1,3 m Semi-automatic PIPE BENDING MACHINE Operating modes are manual but also semi-automatic Application: for multiple bending of pipes The swivel unit with bending preselection for 3 different bending angles in single and automatic mode. The machine is currently equipped with a stop bar for tube size Ø 10mm for 6 angle settings. The bending machine is movable/adjustable. Equipment/accessories: 6 cam rods/stop rods Dcjdpfju Ibyyex Ac Hok 6 control disks Bending tool for Ø 12mm *

Condition: used, Year of manufacture: 1980s/90s Technical data: Centre height: 185 mm Centre distance: 750 mm Turning diameter over bed: 370 mm Dcodeydk Hhopfx Ac Hsk Spindle bore: 36 mm Bed width: 250 mm Speed range: 38 - 1600 rpm Tailstock taper: MT 3 Quill stroke: 110 mm Dimensions (W x D x H), approx.: 1950 x 900 x 1200 mm Weight, approx.: 800 kg Equipment: - 3-jaw chuck, make: Röhm, ø 200 mm - Quick-change tool post with 4 holders - Bed stop - Chip tray

Condition: good (used), NHH lathe Type: 1N611N Turning diameter bed: 260 mm Turning diameter support: 160 mm Spindle bore: 26 mm Turning lenght: 600 mm Dsdpfxjqgdkio Ac Hsck Digital measurement Diameter faceplate: 155 mm Speed: 2000 RPM Dimensions: 150x85x155 cm LxWxH

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication Dcsdpfx Acek S Htxs Hsk - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition

Condition: new, Year of construction: 2024, functionality: fully functional, Price for the purchase of a powder coating system – Negotiable!! • Electrical data: 100-240V 50-60Hz • Powder feed rate up to: 200g / min • Air consumption up to: 250L / min at 6 bar • Air quality / moisture: less than 1.3 g / nm3 • Air quality / oil: less than 0.1 mg / nm3 Data for the powder coating gun • Output voltage: 100 kV Dcjdjg U I Ugjpfx Ac Hek • Max. output current: 100 µA • Hose length: 6 m - antistatic hose • Polarity: Negative • Conformity: ATEX 2mJ Description • Applicator for quick color changes, ready to use out of the box • Intuitive 7" touch display • Automatic cleaning function – gun flushing • Up to 20 user-defined programs • 3 automatic programs • Remote control of paint quantity and program change from the handle Equipment • Controller of the PSS series • ProfiJector RI-1 blunt powder injector • ProfiGun powder gun with quick coupling and remote control • Set of hoses • Stand with vibrator and extraction unit with fluidization PSS driver • 7-inch touch panel, operable with gloves • 3 automatic programs (overcoating, hard-to-reach areas, flat surfaces) • Graduation in 0.1kV and 0.1uA steps • Advanced pneumatic valves for air flow control (romer - patent pending) • Actual air flow measurement responds to errors such as pressure drops or system blockages • Extended diagnostic tools • Possibility to name programs • Possibility to control external master controllers with ModBus protocol (A series) ProfiGun PM-1 gun • A lightweight ergonomic gun, perfectly balanced with a contoured handle • The ceramic cascade with a voltage of up to 100,000V efficiently charges all types of powders • The new nozzle generation ensures perfect powder penetration into complex shapes • The profiled nut provides a good grip • The conductive handle with a high carbon content offers excellent grounding for the painter • The spray gun is made of special materials with increased impact resistance • Fully disassemblable design with a replaceable powder path tube • The spray gun is patented in the USA and the EU • Cascade polarity - negative ProfiJector powder coating pump Description • Design of a new efficient injector • The most effective feed angle, proven by research • Saves paint and air compared to injectors with a right angle • Compared to other pumps, it is characterized by relatively low operating costs • The injector is covered by a European patent