Vertical machining center

IBARMIA ZV 40/L 3000

Year of construction: 2008, condition: ready for operation (used), Sanding range: 2000x900mm, transverse movement: 875mm, longitudinal movement: 2450mm, distance table to spindle center: 845mm, magnetic clamping plate dimensions: 2000x800mm, max. table load: 2.3t, feed rate longitudinal axis: 1000-30. 000mm/min, feed transverse axis: 0,01-2000mm/min, feed vertical axis: 0,001-1500mm/min, grinding wheel dimensions: 500x100x203,2mm, power grinding spindle motor: 22kW, length: 6800mm, width: 3450mm, weight: 13t. On-site inspection is possible. Dedpouyk N Isfx Aiweut

Condition: good (used), Year of construction: 2007, Parts shown by hand not come. Technical details shown on picture. Duodpfjrpn Dvsx Aiwst

Condition: like new (used), Year of construction: 2018, operating hours: 23,501 h, functionality: fully functional, turning length: 705 mm, turning diameter: 366 mm, spindle motor power: 18 W, spindle speed (min.): 4,000 rpm, spindle speed (max.): 10,000 rpm, travel distance X-axis: 260 mm, travel distance Y-axis: 50 mm, travel distance Z-axis: 795 mm, rotational speed (max.): 10,000 rpm, total height: 2,395 mm, total length: 5,330 mm, total width: 4,100 mm, overall weight: 8,360 kg, CNC controller: Mitsubishi M730UM (CELOS - ERGOline Touch) Capacity X-axis travel mm: 260 Y-axis travel mm: ±50 Z-axis travel mm: 795 Turning length mm: 705 Max. turning diameter mm: ø: 366 Swing over bed mm: ø: 920 Swing over cross-slide mm: 740 Bar work capacity mm: 80 Tool magazine Magazine places: 20 Tool holder: BMT40 Upper turret Number of tool slots St .: 20 Speed driven tools RPM: 10.000 Drive power driven tools kW: 5.5/4.9/4.2 (3 min/5 min/cont) Rapid Feed Rate: 30 Main spindle Speed spindle rpm: 4.000 Drive power spindle kW: 18.5/18.5/15 (25%ED/50%ED/cont) Maximun torque Nm: 49 Counter spindle Speed spindle rpm: 5.000 Drive power spindle kW: 11/7.5 (25%ED/cont) Maximun torque Nm: 22 Dodpfeywtwwsx Aiwout Counter spindle travel mm: 734 Coolant system Tank capacity liter: 366 Equipment Electronic Handwheel Chip conveyor Signal lamp High pressure pump Measuring probe Paper band filter Working time hours Under power: 23.501 Cutting Time: 7.494 Potencial nominal kVA: 48 Basic machine dimensions / weight Length mm: 5.330 Width mm: 4.100 Height mm: 2.395 Weight kg: 8.360

Condition: new, Year of construction: 2024, functionality: fully functional, Incorrect investment by a corporation. Machine is new and unused (already delivered). The machine is available immediately with no lead time. An extremely rare opportunity. Machine type: Horizontal machining center with pallet changer Model series: NHX 8000 Control: Siemens S840Dsl with CELOS Measuring system: fully closed loop scale feedback (X/Y/Z) Machine concept: DCG Travel paths X/Y/Z: 1,400 / 1,200 / 1,350 mm Dedsxizdaspfx Aiwjut Rapid traverse X/Y/Z: 50,000 mm/min Pallet system: Turn-type pallet changer Number of pallets: 2 Pallet size: 800 × 800 mm Pallet load: 2,200 kg [optional 3,000 kg] Max. workpiece Ø/H: 1,450 mm / 1,450 mm Pallet change time: 16 s B-axis: direct drive Minimum index: 0.001° Maximum speed: 100 rpm Spindle: powerMASTER Speed: 16,000 rpm Power: 85/50 kW (10% duty cycle / continuous) Torque: 549/279 Nm Taper: HSK-A100 Cooling: central spindle cooling Internal coolant: optional CTS 7 MPa Tool magazine: chain-type, 60 positions [optional 100/120] Rack magazine options: 180 / 240 / 330 positions Max. tool diameter with adjacent tools: 110 mm Max. tool diameter without adjacent tools: 320 mm [for >10,000 rpm: 230 mm] Max. tool length: 800 mm Max. tool weight: 30 kg Tool-to-tool: 1.9 s Cut-to-cut: 5.0 s Equipment / Options: - Workpiece probe - Tool measurement - Laser control (optional) - High-pressure coolant 7 MPa (optional) - Chip conveyor - Fully enclosed enclosure with roof Dimensions n.a. Weight n.a. Connection data n.a.

Condition: used, TECHNICAL DETAILS - Number of axes : 4 MILLING SPINDLE Dsdpew D Hwwjfx Aiwsut - Tool holder type : BT50 - Spindle power : 45 [kW] - Spindle speeds : 12000 [rpm] LINEAR AXES - Travels on X/Y/Z axes : 1700/1400/1240 [mm] - Rapid traverses rates (X/Y/Z) : 48 [m/min] - Cutting feed rates (X/Y/Z) : 20 [m/min] B ROTARY AXIS - Travel : 360 [°] - Indexing precision : 0.001 [°] TOOL CHANGER - Auto. Tool Changer type : Bras chargeur - Tool magazine capacity : 60 - Tool exchange time : 6 [sec] PALLET CHANGER - Pallet changing device type : Rotopalette - Pallet size : 1250/1250 [mm] - Pallets number : 2 - Maximum weight upon pallet : 3000 [kg] - Distance table center / spindle nose (min./max.) : 70-1470 [mm] - Maximum workpiece diameter : 1970 [mm] POWER SUPPLY - Supply voltage : 400 [V] WEIGHT & DIMENSIONS - Machine weight : 32500 [kg] MACHINE HOURS - Number of hours under power : 34422 [h] EQUIPMENT - CNC : Fanuc 31i-model B5 Interface : Ethernet / RS232 / USB / PCMCIA - Electronic handwheel - Rigid tapping - 3 colors status lamp - Coolant tank * with high-pressure pump : 70 [bars] * Coolant through spindle * with paper filtering unit * with cooling unit for coolant * With cabin washing - Chips conveyor - Tool probe - Workpiece probe : Renishaw RMP60 - Electric transformer

Condition: good (used), Year of construction: 2007, Used OKUMA lathe - Model: LT200-M TwinStar - Year: 2007 - including chip conveyor - coolant tank - immediately available Dujdpfsv S Svvsx Aiwjt

Condition: excellent (used), Year of construction: 2013, Traub TNL 18-7B CNC Automatic Lathe Base machine: 2441 x 1396 mm Weight: 3800 kg Spindle height above floor: 3800 mm Connected power: 24 kW Main spindle Max. bar capacity: 18 mm Max. speed: 12,000 rpm Cross-cut speed: 5,000 rpm Z stroke: 205 mm Rapid traverse: 40 m/min Z measuring system resolution: 0.001 mm Feed force: 3000 N Spindle head / short taper: Traub short taper mount Max. clamping force: 1400 daN Max. clamping pressure: 40 bar Min. clamping pressure: 7.5 bar Piston area: 40 cm2 Total cylinder travel: 5 mm Clamping tube thread: M25 X 1 Counter spindle Workpiece diameter: 21 mm Workpiece clamping depth: 180 mm Max. speed: 12,000 rpm Strokes: X: 120 mm Y: -20/+40 mm Z: 250 mm Rapid traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Max. clamping pressure: 30 bar Min. clamping pressure: 10 bar Top tool turret with B-axis Number of stations: 8 Shank cross-section, turning tool: 16 x 16 mm Stroke: X: 120 mm Y: -25/+40 mm Z: 250 mm Rapid traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Chip-to-chip time: 0.5 sec Measuring system resolution: X: 0.0005 mm Y: 0.0005 mm Z: 0.001 mm Lower tool turret Number of stations: 7 + counter spindle Shaft cross-section, turning tool: 16 x 16 mm Stroke: X: 120 mm Y: -20/+40 mm Z: 250 mm Rapid traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Chip-to-chip time: 0.5 sec Measuring system resolution: X: 0.0005 mm Y: 0.0005 mm Z: 0.001 mm Tool drive for upper tool turret Number of driven stations: Max. 8 Drive power: 2 kW Max. speed: 12,000 rpm Torque: 3.9 Nm Tool drive for lower tool turret Number of driven stations: 7 + counter spindle Drive power: 3.4 kW Max. speed: 12,000 rpm Torque: 7.3 Nm Tool drive for the rear unit Number of stations: 7 Number of driven stations: max. 3 Pitch spacing: 46 mm Drive power: 2 kW Max. speed: 7,500 rpm Torque: 4.7 Nm Drive power: 2 kW Max. speed: 4,000 rpm Torque: 11.8 SCOPE OF OFFER INCLUDES (list is not exhaustive): Traub CNC lathe Tool holders, driven and non-driven Duodpfx Aiowg Takewot High-pressure and belt filter system Oil mist separator Fire extinguishing system Chip conveyor Bar loader Operational documentation For the exact scope of offer, see the photo gallery No liability is assumed for the accuracy, completeness, or timeliness of the information provided.

Condition: used, Year of construction: 2002, cutting diameter / mm saw band length / mm cutting width / mm KASTO tec AC5 automatic band saw Sawing capacity: 23kW Machine weight: 5.9t Year of manufacture: 2002 Cutting ranges in mm approx.: Round: 530mm Square: 530x530mm Flat: 530x630mm Smallest dimension to be sawn: 10x10 mm Minimum length to be sawn: 6 mm Minimum residual length, single cut: 10 mm Minimum residual length, automatic mode: 35 mm Automatic material feed, single, max. (standard): 600 mm Automatic material feed single max. (optional): 1500/3000 mm Multiple material feed: 9999 mm Machine roller conveyor length: 1568 mm Max. piece weight: 2275 kg Cutting speed: 12-120 m/min (infinitely variable) Cutting feed: continuously adjustable Material feed: with ball screw Dsdpfxoxrg E Ie Aiwsut Automatic feed: with horizontal clamping device Material clamping: hydraulic, continuously adjustable Clamping force Machine clamping device: 200-1000 daN Feed clamping device: 200-2000 daN Saw blade clamping: hydraulic, factory-set Saw blade cleaning: by easily replaceable double brush, driven by a hydraulic motor. Coolant tank volume: approx. 185 l Pump capacity: approx. 25 litres/min On request, we can offer you the 4 immediately available saw blades at an additional cost.

Condition: good (used), Year of construction: 2008, - Max. turning diameter over bed: 700 mm - Turning length: 1,500 mm Main spindle: - Speed range: 2,800 rpm - Enlarged main spindle: Ø 150 mm, bore: 110 mm - Drive power: 30 kW, 900 Nm - Spindle nose: Size 11 Total power requirement: 59.5 kVA Approx. machine weight: 14.5 t Space requirement approx.: 6.4 x 3.0 x 2.6 m EQUIPMENT: - 3-jaw chuck, SMW KNCS-N 400 K11 - Tailstock - Programmable CNC steady rest slide (cross slide NOT retractable) - SMW-AUTOBLOK SLU-3, self-centering steady rest, clamping range Ø 12 - 152 mm - Full clamping cylinder for partial hollow clamping, draw tube bore max. Ø 100 mm - In-process measuring system Renishaw for X-/Z-/C-axis - Programmable CNC tailstock on W-axis - Drilling/milling spindle and C-axis 0.001° - Tool changer: 80 positions Tool system: HSK-A63 - Y-axis travel +115/-115 = 230 mm - B-axis 225°, positioning in 0.001° increments - ICS / internal coolant supply for driven tools - Synchronized thread cutting with driven tools - Software for use of multifunctional tools, e.g. special tool with radially arranged indexable inserts, which can be positioned in the drilling/milling spindle at 60°, 90°, 120° and 180° positions - Software for gear hobbing for straight and helical gearing with speed synchronization of main and milling spindles Dusdpfexmirgsx Aiwot - Electrostatic extraction unit - Chip conveyor - Documentation - CE marking

Condition: good (used), The powered tools listed here with VDI 50 interface are designed for a SAUTER tool changer and are in good condition as well as fully functional. They were previously used on a GILDEMEISTER CTX 600 CNC lathe. 6 x driven tools, straight version, brands NACKE and WTO, VDI 50 for SAUTER-brand tool turret: Dujdpfobql S Hsx Aiwjt Item No.: XVI 24275 1 drilling/milling unit, straight version, manufacturer: NACKE, VDI 50 mm, similar to DIN 69880, no. 40.5040 / 80 96 / 027.1, collet Ø 25 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €545.00 plus statutory VAT. Item No.: XVI 24277 1 drilling/milling unit, straight version, manufacturer: NACKE, VDI 50 mm, similar to DIN 69880, no. 40.5040 / 80 96 / 027.3, collet Ø 25 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €400.00 plus statutory VAT. Item No.: XVI 2687 1 drilling/milling unit, straight version, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €650.00 plus statutory VAT. Item No.: XVI 2687 1 drilling/milling unit, straight version, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €650.00 plus statutory VAT. Item No.: XVI 2687 1 drilling/milling unit, straight version, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €650.00 plus statutory VAT. Item No.: XVI 2687 1 drilling/milling unit, straight version, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: €650.00 plus statutory VAT. Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany