Drilling and Milling M/C

HBM BF 45 Profi DRO

Condition: new, WMD45 - ROGI Drill Cutter Drilling capacity ----- 45 mm Spot milling capacity ----- 80 mm Finger milling capacity ----- 32 mm Dimensions of the work table ----- 800 x 240 mm Gtjdpfsga T Anox Ahvsw Dimensions of the T-slots ----- 14 mm Spindle mounting ----- ISO30 Maximum distance spindle - table ----- 460 mm Spindle stroke ----- 120 mm Head tilt ----- Left / Right 90 Degrees Longitudinal displacement of the work table ----- 560 mm Transverse displacement of the worktable ----- 230 mm Speed range 75 - 3200 rpm Weight ----- 350 KG Motor ----- 1.1 KW Voltage ----- 400V-3F INCLUDED * Drill head with pin ISO30 - B16 * Left / Right switch * Spindle protection * Fine adjustment * 2 Speed motor * Driven wedge * Tap function * Digital depth stop * CE plug OPTIONS * Base cabinet * Router clamp * ISO30 router bit holder + 12 collets in case * Router set

Condition: used, abrasive belt measures: 50 x 100 Ø mm Gtedpfob Tcv Hsx Ahvjw engine: 380 V, 0,7 kW space needed: 650 x 550 x 1050 mm

Condition: used, functionality: not functional, Year of construction: 1971, The abbreviation LARC stands for Lighter Amphibious Resupply Cargo. This refers to the tailgate of the vehicles, which enabled the military to transport a truck or other military equipment. The XV in LARC denotes the maximum payload: 15 tons. The vehicles are made of aluminum and have the following (precise) dimensions: 13.71 m in length, 4.41 m in width, and 4.70 m in height. (American measurements: 45 ft x 15 ft x 14 ft). The original LARC vehicles were equipped with two Cummins 8-cylinder diesel engines, each delivering 300 HP. On land, the vehicles could reach a maximum speed of 48 km/h and, on water, 9.5 knots, which is approximately 18 km/h. The unladen weight of the vehicle is 22 tons. The maximum permissible weight was 35.5 tons. Gtodpfxexcgy Ho Ahvsw The previous owner intended to convert the boats to fully electric drive in order to subsequently organize tours on the Wadden Sea. Around €200,000 was invested, but the project was not completed. The diesel engines have been removed and are no longer available. Battery packs are present and partially installed. The exact remaining work required is not known.

Condition: good (used), Year of construction: 2005, Hurco machining center VMX 1 condition see pictures Gsdpov Nzucofx Ahvotw

Condition: used, Column drilling machine ALZMETALL type AB 4 SV Machine no. No. 14805 Year of construction approx. 1980 drilling capacity 40 mm Spindle holder MK 4 - short quill throat 340 mm Quill stroke 180 mm Table size 710 x 560 mm Column diameter 160 mm Spindle speed 30 - 765 rpm infinitely variable Motor power 2.3 and 3.4 kW pole-changing Mains connection 380 Volt, 50 Hz - Spindle speed via 2 motor speeds and infinitely variable via variator gearbox - Reduction gear with 2 gear stages for high torque at low speeds - Spindle on/off via rotary switch or electric foot switch - Automatic feed 0.1 - 0.2 - 0.3 mm/rev - Table height adjustment via hand crank - Machine base with machined workpiece support surface - LED lighting device Gedpfon N Ekcsx Ahvetw Space requirement L x W x H 1200 x 725 x 2050 mm Weight 615 kg good condition

Condition: used, Iron lathe Gtsdpfxordmm Dj Ahvsw

Condition: used, Clamping plate, marking-out plate, measuring plate, measuring table, welding table, welding table, straightening plate -Clamping plate comes: from a measuring machine -Width: 1335mm -Length: 3000mm -Height: 250mm -Plate thickness: 40 mm Gtjdpfx Aefc T Tqohvsw -Plate is with: support ribs -with: 4x adjustable feet -Number: 1 piece available -Transport dimensions: 3000/1335/H750 mm -Weight: 2749 kg

Condition: excellent (used), Drilling capacity -20 mm Spindle taper FEHLMANN Spindle speeds 50-6300 rpm Throat 276 mm Cross table 530 x 255 mm Digital read-out Accessories Godpfx Aouy Sazjhvetw MARCELS MASCHINEN CH

Condition: new, distance between shaft and table: 470total power requirements: 2,2 kwweight approx.: 1,2messurements (LxWxH): Länge2400 mm Breite/Tiefe2160 mm Höhe2300 mm Gewicht 1200 kgspindle rotation speed: 60 4200 min¯¹ Godpod H Hhzofx Ahvjtw

Condition: new, bore capacity in steel (diameter) 13,0 mm x-travel 300 mm y-travel 130 mm turning speeds 100 - 2500 U/min throat 165 mm spindle taper MT 3 MK table-size 490 x 120 mm diameter of hob 30,0 mm Gtodpfx Ajxabb Hjhvew motor 230 Volt total power requirement 0,75 kW weight of the machine ca. 50 kg. dimensions of the machine ca. 520x500x740 mm Scope of delivery: - Key chuck 1 - 13 mm / B 16 - Drill chuck arbor MK 3 / B 16 - tightening spindle M 12 - Height-adjustable protective cover - operating key