4 roll plate bender 3000 x 160 mm

Haeusler VRM-HY

Year of construction: 1978, condition: ready for operation (used), A Haeusler CNC large-format 4-roll plate bending machine is available. Number of rolls: 4, Roll width: 3050mm, Max. prebending plate width: 3000mm, Max. prebending plate thickness: 60mm, Max. rolling capacity at max. plate width and 3500mm bending diameter: 70mm, Roll diameter top/bottom/side: 620mm/600mm/500mm, Max. top roll load: 12000kN, Operating speed: 4m/min, Connected load: 132kW, Weight: approx. 85t. Including cone bending device. Documentation available. An on-site inspection is possible. Lrsdozka H Aspfx Ahksr

Condition: new, functionality: fully functional, Year of construction: 2026, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed performance: for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Lrjdet Akt Repfx Ahkor Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Variable geometry with linear guides for roller movement Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Year of construction: 1981, condition: ready for operation (used), Working width: 2500mm, max. sheet thickness: 20mm, lateral cylinder support device with three adjustable support rollers and conical bending device, machine provided for exchangeable top rollers up to min. Ø 450mm, machine revision 2009, factory inspection 2012. Lrjdpfxonvfdbs Ahksr

Condition: used, Year of construction: 2005, total length: 7,800 mm, total width: 1,700 mm, total height: 1,580 mm, Colour: Green Empty weight: 11.000 kg Price: On request - Year: 2005 - Documentation available: No - CE certificate present: No - Drive system: Conventional - Drive: Hydraulic - Number of rolls [pcs.]: 4 - Number of driven rolls [pcs]: 2 - Max. sheet thickness [mm]: 12 Lodpfx Aszkkrvohksrr - Max. prebending thickness [mm]: 10 - Max. working width [mm]: 2500 - Top roll diameter [mm]: 360 - Bottom roll diameter [mm]: 300 - Transport dimensions: 7800mm x 1700mm x 1580mm (l x w x h) - Transport weight [kg]: 11000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Year of construction: 1993, condition: ready for operation (used), machine/vehicle number: Seriennummer: 9302394, CNC-Control HATASTAR 2000 The press capacity is 500 t or 5000 kN In addition to the machine tools are available Switch Cabinet left X1- + R-/ X2- + R-Axe on round guide Lredped Egc Asfx Ahkjr Y1- + Y2-Axe hydraulic Upper tool clamping pneumatic sheet metal trace-device Second tow-hands Operation universal matrice 100x100x5'100 mm knife 280 x 5'100 mm Matrices-central plate, b = 111 mm

Condition: used, functionality: fully functional, Year of construction: 1992, machine/vehicle number: 10842, We are offering this pre-owned sheet metal rolling machine Chr. Häusler VRM-hy 3000x15, year of manufacture 1992. Model: VRM-hy 3000×15 Serial number: WO 10842 Lrsdpfxex Sqc To Ahksr Year of manufacture: 1992 If you have any questions or require further information, please do not hesitate to send us a message or call us.

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Make: HAEUSLER Lodpfezbqquex Ahkerr Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: refurbished (used), functionality: fully functional, Year of construction: 2007, DAVI_MCB 3060 WT 4-roll plate bending machine CNC _ 3000x65 MM - Year of make 2007 Capacity plate width 3100 mm Plate thickness 65 mm Ljdpfx Asy D Npishksrr Prebend 55 mm TOP ROLL 600 MM LOWER ROLL 550 MM Configuration installed: • Surface hardening of the four rolls • Dual pre-pinch, with adjustable force upon the input of plate thickness • Conical bending hydraulic attachment - hardened contrast pad. • Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. • Calibration system for re-rolling of welded shells rounding. • Console electric independent with centralized commands joysticks and CNC screen readout. • CNC controller DAVI GENIUS semiautomatic and fully automatic programmable. with digital readout of the 4rollers for use in manual operation, • Opening front side hydraulic drop-end to unload closed shells. • Variable working speed step-less axis interpolation. • Safety installation with emergency stop. • Instruction manuals for operation and service Voltage electric 3phase Vac 380/50 power Kw 75 nr.1 top support hydraulic operated , shell ID max 5 mtrs - CNC programmable nr.1 side support hydraulic on the left nr.1 side support hydraulic on the right, finger pusher to swing the sheet plate forming cones rolling.

Year of construction: 1978, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1978 Specifications Metric US Standard Rolling width 3050 mm Rolling thickness 3x toproll Ø 60 mm Rolling thickness 5x toproll Ø 70 mm Rolling thickness prebending 50 mm Top Roll Ø 630 mm Bottom Roll Ø 600 mm Side roll Ø 500 mm Number of rolls 4 Rolling speed 0 - 5 Lodpfx Aekvm S Nshkerr Adjustiment lower roll 200 mm/min. Adjustment side rolls 200 mm/min. Number of driven rolls 2 Power 120 kW Dimensions (Estimate) Length 5790 mm Width 4200 mm Height 4200 mm Weight 85000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1980, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1980 Specifications Metric US Standard Rolling width 3000 mm Rolling thickness 3x toproll Ø 130 mm Rolling thickness 5x toproll Ø 140 mm Rolling thickness prebending 120 mm Top Roll Ø 950 mm Bottom Roll Ø 850 mm Side roll Ø 180 mm Number of rolls 4 Rolling speed 2 + 4 Adjustiment lower roll 0 - 400 mm/min. Adjustment side rolls 0 - 400 mm/min. Number of driven rolls Lrsdpjkvm Szefx Ahkor 2 Power 132 + 37 kW Dimensions (Estimate) Length 12000 mm Width 5440 mm Height 5650 mm Weight 286000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1993, HENKE VARIANT 140/120, dual-feed machine, year of manufacture 1993, 2 moulds, new control system Lrodoxl S Uhjpfx Ahkor

Condition: excellent (used), Year of construction: 1997, number of rollers: 4, roller (bottom) diameter: 280 mm, roller (top) diameter: 200 mm, side roll diameter: 280 mm, roller length: 3,000 mm, sheet thickness (max.): 6 mm, overall weight: 7,250 kg, total length: 6,000 mm, total width: 2,000 mm, total height: 2,000 mm, power: 6 kW (8.16 HP), 4 roll plate bender HAEUSLER - VRM-HY MACH-ID 9604 Make: HAEUSLER Type: VRM-HY Control: HAEUSLER CNC Rolling width: 3000mm Rolling thickness 3x toproll Ø:4mm Rolling thickness 5x toproll Ø:6mm Rolling thickness prebending: 3mm Top Roll Ø: 200mm Bottom Roll Ø: 280mm Side roll Ø: 280mm Number of rolls: 4 Rolling speed: 0-5 Adjustiment lower roll: 0-200mm/min. Adjustment side rolls: 0-200mm/min. Number of driven rolls: 2 Power: 6kW Ledpfxey Expuo Ahkorr Length: 6000mm Width: 2000mm Height: 2000mm Weight: 7250kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, functionality: fully functional, Year of construction: 1971, For sale: this four-roll plate rolling machine, type VRM HY 3000/18. The machine is connected and can be tested. Weight: 24,000 kg. Lodpexwqdrsfx Ahksrr

Year of construction: 2007, condition: ready for operation (used), A CNC profile drilling machine Voortman with a movable drilling cabin is available. Working height range: 30mm-1050mm, positioning speed: 40m/min, table width: 300mm, max. working width: 1800mm, support depth: 1500mm, tool stations: 5, max. travel speed: 40m/min, tool holder: SK40, drilling diameter range: 5mm-40mm, thread cutting range: M6-M30, working length: 16200mm. Documentation available. On-site inspection possible. Lrjdpsxp Rb Ijfx Ahksr