Bolster plate

GERD WOLFF 1500 x 1500 x 800mm

Condition: used, Year of construction: 1999, x-travel 12000 mm y-travel 3600 mm z-travel 1500 mm spindle turning speed range 3000 U/min Control: Heidenhain iTNC430 Milling head 2 axes, indexed 2.5° Vertical (Y-axis): 3600 mm Transverse (Z-axis): 1500 mm Longitudinal (X-axis): 12,000 mm Guide rail length: 14,700 mm Guide rail width: 1400 mm Lowest milling position of the spindle nose measured from the floor (head horizontal): 855 mm Low column design 870 x 900 x 2,625 mm: 3,000 kg High stand design 870x900x3,025 mm: 3,500 kg Motor power: 37 kW Mounting: ISO 50/ DIN 69871-A Speeds: 11.7:231:3000 rpm Feed range: 2:2500 mm/min Rapid traverse X-axis: 12000 mm/min Z-Y axis: 15000 mm/min Feed motor power X-axis: 55 Nm Z-axis: 37 Nm Y-axis: 37 Nm Accuracy Positioning accuracy: 0.025 mm Repeatability: 0.015 mm Weight: approx. 42,000 kg Air supply to the machine: 300 L/min at 4.5 bar NOTE: The clamping plates and chip conveyors are not included in the scope of delivery. Lrodpoxwdygsfx Afaok However, we can offer you both used and new clamping plates and chip conveyors on request.

Condition: ready for operation (used), Year of construction: 2009, operating hours: 9,192 h, travel distance X-axis: 1,200 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 500 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, spindle speed (max.): 16,000 rpm, number of axes: 3, This 3-axis HERMLE C 1200 vertical machining centre was manufactured in 2009. It features an impressive X-axis travel of 1200 mm, Y-axis travel of 900 mm, and Z-axis travel of 500 mm. The machine is equipped with a spindle speed of 16,000 rpm and includes 30 tool stations. If you are looking to get high-quality machining capabilities, consider the HERMLE C 1200 machine we have for sale. Contact us for further details. • X – 1200 mm Lrjdpfx Afjylw Stoaok • Y – 900 mm • Z – 500 mm • Machining Center C 1200 V • Heidenhain iTNC 530 contouring control • Spindle 16,000 rpm • SK 40 • 30 Tool Stations • Rigid Clamping Table • Coolant System • Electronic thermal compensation (iTNC) with temperature sensors on the motor spindle and machine base • Portal design with a closed rear wall for significantly better support during torsional loads • Two axes are located in the tool, providing very good mass distribution and ideal conditions for high rapid traverse and feed rates • Feed screw diameter and pitch (X and Z axes): 40 / 20 mm • Feed screw diameter and pitch (Y axis): 50 / 20 mm • Direct measuring system • Resolution: 0.0001 mm • Position tolerance (Tp) in X-Y-Z axes according to VDI/DGQ 3441: 0.010 mm • Recommended ambient temperature for maintaining accuracy: 20 °C ± 1 °C • Flushing/wash-down system for rinsing the side work area • Display: 15" TFT color flat screen • Flexible contour programming • Part program memory • Tool diameter capacity: 80 mm • Tool diameter with free adjacent slots: 125 mm • Maximum tool length: 300 mm • Maximum tool weight: 8 kg • Maximum magazine load: 120 kg • Chip-to-chip tool change time according to VDI 2852: 6.5 seconds • Manual control unit includes electronic handwheel, axis direction keys, feed control, rapid traverse, emergency stop, and enable switch • Machine on – 11,927 h • Spindle on – 9,192 h Additional equipment • Chip conveyor • Heidenhain touch probe • Electronic Manual Control Module (iTNC) Technical Specification Taper Size SK 40

Condition: excellent (used), Year of construction: 2002, x-axis 4000 mm y-axis 3500 mm z-axis 1500 mm Control SIEMENS 840 D w-axis 1500 mm column daylight 2500 mm surface area 3000 x 2000 mm Lsdpfx Aovwgmmofaork workpiece weight 10000 kg spindle turning speed range 5-6000 U/min transmission ratio 2 power capacity - milling spindle 45 kW dist. cutter spindle - workpiece spindle 3500 mm max. torque on the spindle 1250 Nm tool change unit 200 -fach tool diameter 135 / 250 mm weight of tools max. 50 kg tool length - max. 400 mm tool taper ISO SK-50 the portal milling machine is in very good condition. ADDITIONAL EQUIPMENT DRILLING/MILLING Angle milling head yes automatic tool clamping yes Tool clamping yes Ball screws yes Guideway cover yes Coolant system yes High-pressure cooling system (internal cooling) yes Full work area panelling yes Portal machining centre with tool changing system and second table top.

Year of construction: 2011, condition: ready for operation (used), - USED - TRAVELLING COLUMN CNC MILLING MACHINE WITH ROTARY AND SHIFTING TABLE Ljdpfx Afowl R Agsasrk LONGITUDINAL TRAVEL: 8000 mm TRANSVERSAL TRAVEL: 1500 mm VERTICAL TRAVEL: 2500 mm RAPID FEEDS L-T-V: 35 m/min TABLE SIZE: 2000 x 2000 mm TRANSVERSAL TRAVEL OF THE TABLE: 1500 mm MAX ADMITTED LOAD: 15000 Kg HEAD: A/B AXIS AUTOMATIC ; CONTINUOUS ; ISO 50 ; 7000 rpm; 49 kW; 1180 Nm TOOL MAGAZINE: CHAIN-TYPE ; 80 POS CONTROL UNIT: HEIDENHAIN iTNC 530 ACCESSORIES: SWARF CONVEYOR ; LASER TOOL SETTER ; PORTABLE HANDWHEEL NOTE: WITH ROTARY TABLE 1500X1500 mm; MAX ADMITTED LOAD 15000 Kg

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 20194, travel distance X-axis: 4,000 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 1,500 mm, power: 49 kW (66.62 HP), Features High rigidity for heavy-duty machining Large table for oversized workpieces CNC control with HEIDENHAIN TNC 530 for precision operations Automatic tool changer with 50 positions Centralized lubrication and hydraulic system Lrsdpfxsx S Hgzs Afaok

Condition: good (used), Year of construction: 1995, functionality: fully functional, travel distance X-axis: 10,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 3,000 mm, - CNC control Heidenhain TNC 415B - controlled 2-axes NC-milling head 2,5° - coolant device The machine will be sold without the plate field Accessories: ca. 20 pieces tool tapers DIN 2080 with bolts DIN 69872 some spare parts like bevel gears for the milling head and ball screw for X-axis. Technische Daten / technical details: Verfahrweg X längs / X-travel longitudinal 10000 mm Verfahrweg Y quer / Y-travel cross 1500 mm Verfahrweg Z vertikal / Z-travel vertical 3000 mm Werkzeugschaft / spindle taper SK50 Drehzahlbereich (2-stufig) / spindle speed (2-steps) 35-3000 UpM /rpm Vorschub / infeed 6-10000 mm/min Eilgang X,Y,Z / rapid feed X,Y,Z 10, 15, 10 m/min Lsdpfx Afswrzkzsaork Antriebsleistung Hauptmotor 100%ED / drive capacity main motor 100%ED 37 kW Gewicht der Maschine ca. / weight 39300 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: used, Year of construction: 2013, machine/vehicle number: 5279, travel distance X-axis: 8,000 mm, travel distance Y-axis: 1,600 mm, travel distance Z-axis: 1,300 mm, spindle speed (max.): 4,000 rpm, spindle speed (min.): 22 rpm, Year of construction 2013 Control system: SIEMENS Sinumerik 840D pl HSK 100-A tool holder TRAVEL horizontal-longitudinal X = 8,000 mm Vertical headstock slide Y = 1,600 mm Headstock horizontal-transverse Z = 1,300 mm FUNCTIONAL PROBE: m&h HSK 100 SIEMENS B-MPI HAND-HELD CONTROL UNIT TRAVELING WORK PLATFORM 3-SIDED SPRAY AND CHIP PROTECTION WALL CHIP CONVEYOR SPRAYING PLATE Sizes: Length: 10,000 mm Width: 2,500 mm WASHING GUN IN THE WORKROOM REINFORCED COOLANT SYSTEM Pump capacity: 32 l/min at max. 20 bar Coolant tank: 2000 l COLLISION MONITORING SYSTEM 2 CHANNEL pcs. 2 monitoring channels: - 1st collision monitoring orthogonal milling head (channel 1) - 2nd collision monitoring fork head (channel 2) PENDULUM MACHINING 3 WORK AREAS MILLING SURFACE INTERPOLATION (TRAORI, 3D tool radius compensation, spline interpolation) ROTATED AXIS COORDINATE SYSTEM 2 PICK-UP STATION For fork head, arranged on clamping plate Storage positions 10 Maximum tool weight kg 12.5 Maximum tool length mm 200 Maximum tool diameter mm 63 Maximum tool diameter when free mm 250 Neighboring position Tool holder HSK 6 AUTOMATIC TOOL CHANGER Number of tools in chain magazine 48 Maximum tool diameter with magazine filled to mm 125 Maximum tool diameter with mm 250 free adjacent positions Maximum tool length mm 500 - Maximum tool weight kg 25 Maximum tool load torque Nm 40 Tool holder HSK 100-A HEAD CHANGE MAGAZINE 1 pc.FORK HEAD WITH HIGH FREQUENCY SPINDLE AUTOMATIC FORK HEAD WITH INTEGRATED HIGH-FREQUENCY SPINDLE - High-frequency milling spindle: - Integrated high-frequency spindle - Tool holder HSK - A 63 DIN 69893 - Main drive power 20 kW at 100 % ED or 25 kW at 40 % ED Lredpfx Aju Sppwsfaok - Speed range up to 20,000 1/min - Motor spindle bearing with permanent grease lubrication - Sealing air seal - Torque: 40 Nm at 100% ED, 50 Nm at 40% ED - Automatic tool clamping - Power transmission according to speed-performance diagram GMN HCS 170 - Technical data according to data sheet E 745.1467.00 UNIVERSAL MILLING HEAD IN ORTHOGONAL DESIGN - Liquid-cooled milling head - Cast construction made of GGG 60 - Milling head, automatically swivels 180 x 1 degree - The resulting positions can therefore not only be approached via the CNC control, but also programmed and processed - Repeat accuracy at the spindle nose ±0.002 mm, part accuracy thus ±3 sec - HSK 100-A tool holder - The milling spindle is equipped with a hydromechanical quick tool clamping system - Tool pull-in force: 45 kN - Internal coolant supply form A-D - External coolant supply via shower ring - Speed range 22- 4,000 1/min MAIN DRIVE by a frequency-controlled liquid-cooled AC motor with - 32 kW drive power at 100% duty cycle, 46 kW at 40% duty cycle. Direct power transmission WITHOUT gearbox, therefore no heating or wear of a gearbox. - 637 Nm torque at 100% ED, 875 Nm at 40% ED

Condition: excellent (used), operating hours: 8,064 h, Brand : LAGUN Model : GBM-22E Type : CNC 5 EJES Cnc :HEINDENHAIN 530 Table dimensions : 2.200 x 1000 mm Number and width of T slot: 7 x 22 mm Distance between T slots: 140 mm Axis travels (X,Y,Z) : 2.000 x 1.200 x 1.000 mm Head type : Automático Spindle speed : 4.000 rpm Taper : ISO 50 DIN 2080 Main motor : 28 kw Continuusly variable speeds : 50➗ 4.000 Speed range : 2 Rapid traverse : 10.000 mm/min Machine weight : 15 tn Electronic hand-wheel : Yes Ledpjyg R Abjfx Afaerk Working hours : Machine running: 22.924 h Control on : 23.132 h Automatic cycle: 8.064 h

Condition: used, Year of construction: 1973, spindle diameter 130 mm x-travel 3000 mm y-travel 2000 mm total power requirement 4,5 kW weight of the machine ca. 30 t Spindle Ø 130 mm Lodot Hwt Sjpfx Afaerk Spindle taper SK 50 Working range: X = column, longitudinal 3,000 mm Y = headstock, vertical 2,000 mm Z = spindle stroke 1,000 mm Lower table 3,300 x 2.400 mm Max. weight on table 10 tons/m² Min./ max position of work spindle above table 770 / 2,770 mm Feeds 0.9 - 2,000 mm/min Quick feed for headstock and column 5,000 mm/min Quill feed 0.5 - 1,200 mm/min Speed range, partially infinitely variable 4.5 - 1,250 rpm Weight, approx. 30,000 kg Accessories / Special Features * HEIDENHAIN Digital Display for 3 axes. * Hardened guideways. * Ball screw spindles. * Infinitely variable spindle speeds and feeds. Feeds can be individually driven with motor. * Moving operating platform. * Hanging control panel. * Manual operating control. * Platform. * Hydrostatics in the column displacement. * Mounting plate 3,200 x 2,500 mm, planed, with t-slots. * Top table approx. 1,400 x 2,600 x height 900 mm, one face is handled. * Hydraulic clamping of column and slides. * Motor driven tool clamp. * Lots of accessories, including tool holders with and without tools, separate chip extractor, clamping aids, 1 angle plate, and other plates. Lots of other accessories. This is a strong machine which is very suitable for heavy cuts and therefore ideal for the machine tool industry and for tool manufacturers. Condition : Good. Machine can soon be inspected under power. Delivery : Ex stock as inspected Payment : Net, after conclusion of contract Thank you for your interest. We have other horizontal borers on stock. Please let us know what you need.

Condition: used, Year of construction: 2004, travel distance X-axis: 6,000 mm, travel distance Y-axis: 2,500 mm, travel distance Z-axis: 1,400 mm, CNC HEIDENHAIN iTNC 530 X-AXIS STROKE 6000 MM Y-AXIS STROKE 1400 MM Z-AXIS STROKE (VERTICAL) 2500 MM SPINDLE CONNECTION ISO 50 DIN 69871-B50 SPINDLE SPEED 5000 RPM MOTOR POWER S1 37 KW - S6 56 KW AUTOMATIC INDEX HEAD 1 ° X 2.5 ° TOOL CHANGER 40 PLACES COOLANT TROUGH THE SPINDLE AND EXTERNAL CHIP CONVEYOR ANCHORING PLATE 8000 X 2000 MM PERIMETER PROTECTIONS Ledpfx Aexhqivefasrk