Recutting circular saw

Esterer DKN

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Vacuum system (with its pump) No. 2 Vertical supporting columns of the top supporting beam No. 1 Horizontal top supporting beam (where the carriage slide on) No. 1 Motorized sliding carriage with horizontal metal arms No. 2 Out-side rollers way (on gound) to in-feed pile of panels to the Loader Csdpfx Ajfi Tg Hei Neha Out-side motorized rollers table (which receives panels from the Loader) Separate electric and command panel Perimetral safety metal grids Working capacity (cycles/min) 16 (ca.) Min/Max panels thickness mm 10 / 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1300 x 3000 (ca.) Total installed motor power Kw 30

Condition: as good as new (ex-display), Year of construction: 2026, S&F drum chipper type ATH 220x530/3 Demonstration machine / trade fair machine / new machine Solid design with long service life Feed height: 200 mm Feed width: 500 mm Number of chipper knives: 2 pieces Number of counter knives: 1 piece Rotor diameter: 520 mm (solid steel rotor) Number of feed rollers: 3 pieces Throughput rate: up to approx. 20 rm/h * Chipping length: approx. 30 mm Chipper drive power: 45 kW or on request Feed roller drive power: 2 x 2.2 kW Operating/control voltage:400/220 V, 50 Hz Weight: 2,600 kg *depending on chipper length, kW main motor, number of knives, feed S&F chippers and drum chippers with horizontal infeed are used in many areas of the wood processing industry (sawmills, timber mills). Chippers from the ‘ATH’ series produce high-quality and homogeneous wood chips with a low proportion of fines from residual wood, for example as quality chips for the cellulose industry or as fuel chips for energy generation Codpfow I R Rnjx Ai Nsha Advantages: - Maximum throughput - Low fines content - Low maintenance - Flexible use - Customised production

Condition: like new (used), Socolest DAS 200 twin-shaft multiblade feeding and receiving table - Made in Italy - centering feeding table - discharge receiving table - top drawing rollers TECHNICAL PARAMETERS: - cutting height 200 mm - cutting width 400 mm - engine power 2 x 55 kW - track width 630 mm - disc diameter max 350 mm - feed speed 40 m / min - hydraulic roller height adjustment - hydraulic cutting height adjustment - hydraulic feed - four top pulling rollers - four rows of anti-rejection latches - shaft diameter 70 mm - sleeve diameter 90 mm - pneumatic side pressure centering - diameter of ferrules 2 x 250 mm - minimum workpiece length 720 mm - laser - feeding table belt 5700 mm - width of table 600 mm - top roller pneumatic pressure roller - speed of table regulated on inverter - receiving table 9200 mm - width of rollers 800 mm - diameter of rollers 135 mm - four drop chains - distance between chains 1900 mm Transport dimensions 1300 cm x 240 cm x 200 cm weight 8 t Chsdpfx Aijqup Ans Nea

Condition: new, Year of construction: 2025, functionality: fully functional, Professional WoodMizer LT70 sawmill, complete configuration, still packaged. The machine was delivered in April 2025 and has never been used. It was assembled by the manufacturer and is ready for operation. Chsdpfx Aieyr I Dmo Nsa

Condition: ready for operation (used), Year of construction: 2023, Load capacity: 1450/1125kg, load center: 600mm, lift height: 3200/4900mm, battery weight: 300-350kg, free lift: 900mm, mast height lowered: 2100mm, mast height extended: 4900mm, reach: 590mm, ground clearance under mast: 80mm, ground clearance at axle center: 50mm, track width: 1292mm, frame cross-section: 1058mm, front overhang: 655mm, wheelbase: 1120mm, rear overhang: 175mm, side shift: 80mm left / 80mm right, lost load thickness: 880mm, fork tilt back: 3°, fork tilt forward: 3°, min. turning radius: 1350mm, support arm height: 282mm, support arm length: 530mm, maximum speed: 6km/h, gradeability: 5%, battery capacity: 24V/270Ah, fork dimensions: 35x100x1070mm, front wheels (polyurethane): OD 200mm / width 50mm, rear wheel (solid rubber): outer diameter 250mm / width 75mm, AC drive motor: 24V / 2.5kW, AC pump motor: 24V / 5kW, rated power: 2.5kW, width: 1512mm, length: 1950mm, net weight without / with battery: 2800/3150kg, operating hours: 86h. An on-site inspection is possible. Chsdpfxsw S Tyao Ai Noa

Condition: good (used), Year of construction: 1995, Chipper with horizontal feed via vibratory chute Chodpfx Aijxc H Rlo Noa Motor: 30 kW Max. feed width: 320 mm Max. feed height: 80 mm With conveyor belt

Condition: new, Year of construction: 2025, MAX MAMMUT 400-500-600: High speed log profiling line (up to 600 mm in diameter) for the production of prisms, "river use", "trieste use" beams, boards in general and semi-finished products for pallets. FULLY HYDRAULIC MACHINERY Minimum diameter of logs 120 mm Maximum diameter of logs 600 mm Minimum working length mm 1.800 Maximum working length mm "Infinite" (∞) Tool holder shaft diameter 60-80 mm Cutter diameter mm 300 Feed speed mt / min. 5 - 70 Cedshpbthjpfx Ai Nsha

Condition: used, Iseli BS 5 sharpening machine Iseli EBW leveling machine Codpfowgh H Eex Ai Noha

Year of construction: 2006, condition: ready for operation (used), Panel type: Tubular panels for 3-layer parquet, panel length: 2230mm, panel width: 782mm, panel thickness: 9mm-22mm, panel thickness tolerance: 0.5mm/panel, feed rate: 15m-50m/min, output: 12 cycles/min, working height: 1015mm, max. saw blade diameter: 250mm. Extraction included. Documentation available. On-site inspection is possible. Codpfjt Amc Iex Ai Noha

Condition: good (used), Year of construction: 2000, Schroeder Mosaic Press 160mm. Gluing patterns - brick / English pattern plate 640x274mm and halves 640x137mm glued in 6 variants: - single brick offset 50% - double brick offset 50 % - triple brick offset 50 % - single brick offset 25 % Chjdpfxsr Iyvbe Ai Nea - double brick offset 25 % - triple brick offset 25 %