Plate Shear - Hydraulic

ERMAK CNC HGS 4100-6

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in Codpfx Abofg E Hpo Tsrk place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: excellent (used), Year of construction: 2012, Technical Data: Working length: 4100 mm Distance between uprights: 3550 mm Press force: 300 tons CNC control: DELEM EPC-3D Controlled axes: Y1/Y2; X; R; Z1/Z2 Hydraulic tool clamping top and bottom: WILA system CNC crowning Stroke: 550 mm Throat depth: 405 mm Installation height: 620 mm 2 bending aids Angle measuring system Motor power: 30 kW Laser monitoring Table height: 980 mm Dimensions (L x W x H): approx. 5550 x 2950 x 3400 mm Cjdpfx Aexdt Umeb Tjrk Weight: approx. 24.5 tons Accessories: Manual tool changer Segmented bending with step-by-step support of the bending aids (segment bending) 1 set of tools Condition: Very good condition The seller assumes no liability for typing or data transmission errors. The machine’s appearance, technical condition, and wear are consistent with its age; used machines are sold without any warranty.

Year of construction: 2020, condition: refurbished (used), Dear customers! Our experience has shown that the communication by e-mail usually drags out everything unnecessarily. We would like to help you quickly, but it is better to spend three minutes on the phone than three days writing e-mails back and forth. T.S.W.C. 30.20 Dry bulkhead Dimensions: 3000 x 2000 mm W X H + Fan in the height Air capacity: 10.800 m³ / h Motor: 2,20 kW ex-proof Exhaust air pipe: 500 Ø mm depth: 900 mm Double filtration: paper filter + Paintstop filter mat over Cedpfxsfn Ndde Ab Tjrk Terminal strip (+180,- EUR net) Options/additional price for: Paintstop filter mat terminal strip: 180,- EUR net side baffle plates with hinge: 590,- EUR net Pictures may vary. We can also offer you complete spraying rooms with supply air system, heat exchanger, supply air ceiling, piping etc. Just contact us.

Year of construction: 2022, condition: new, Ostas 3-roller round bending machine SBM 1270 x 95 Special equipment included in the price: Hardened rollers Motorized rear roller adjustment Digital display Features: - Asymmetrical 3-roller round bending machine with motorized drive - Hardened rolls - Motorized rear roll adjustment - Digital display - Upper roll can be swung out - Conical bending device - foot switch Technical details: - sheet width: 1270 mm - sheet thickness: 3,0 mm - roll length: 1270 mm Credpog Tzbhjfx Ab Tek - Roll diameter: 95,0 mm - Smallest bending diameter: 140,0 mm - Motor power: 1,1 kW - Dimension L-B-H: 2100 x 760 x 1250 mm - weight: 470 kg

Condition: excellent (used), Year of construction: 1996, Technical data: maximum cutting width: 3100 mm maximum cutting performance for steel St40: 15.0 mm motorized adjustable parallel stop: 1500 mm Csdpfsummw Tex Ab Tjrk motorized adjustable cutting gap adjustment cutting angle adjustment working height: 860 mm motor power: 22 kW side protective grille with light barrier on the back dimensions (length x width x height): approx. 4650 x 3600 x 2050 mm weight: approx. 13.5 tons We can only show a small part of our current range of used machines here. Please also visit our homepage! The seller is not liable for typing or data transmission errors. The machine's appearance, technology and wear and tear are in keeping with its age; used machines are sold without any warranty.

Condition: excellent (used), Year of construction: 2015, operating hours: 27,500 h, Operating hours: 27,500 h Credpfxexbfvwo Ab Tok Laser on: 17,000 h Resonator: 5KW Price on request

Condition: used, functionality: fully functional, Year of construction: 2007, working width: 4,250 mm, type of crowning: CNC-controlled, overall weight: 16,000 kg, total length: 6,000 mm, total width: 1,700 mm, total height: 3,000 mm, - Press beam operating hours: 9,874 h - Stroke: 600 mm - Force: 1,700 kN - Working length: 4,250 mm - 5-axis backgauge - CNC crowning - Hydraulic tool clamping (top/bottom) - Die adjustment for hemming - CNC-controlled bending aid - Bendguard safety device - ACB angle measuring sensor Cedpfoxcxy Sjx Ab Tjrk

Condition: excellent (used), Year of construction: 2015, Technical data: Codpfx Ajxcayaeb Terk Working length: 4100 mm Frame gap: 3700 mm Pressing force: 170 tons Top drive with 4-cylinder design CNC control: TASC 6000 Number of controlled axes: X; R; Z1/Z2 Stroke: 445 mm Throat depth: 410 mm Installation height: 385 mm Working height: 1050 mm Hydraulic tool clamping, top and bottom Pneumatic die shifting, CNC-controlled Crowning, CNC-controlled CE mark Motor power: 37 kW Dimensions (L x W x H): approx. 5650 x 2350 x 3000 mm Weight: approx. 13.5 tons Accessories: Electronic pressure gauge Measuring system with centrally mounted glass scales and temperature compensation Control cabinet cooling BendGuard safety system Network capability Support arm with adjustable height Condition: Overall in very good condition Machine has been stored The seller does not accept liability for typographical or data transmission errors. The machine's appearance, technology and wear correspond to its age; used machines are sold without any warranty.

Condition: used, Year of construction: 2012, operating hours: 25,000 h, total length: 5,250 mm, total width: 2,350 mm, total height: 2,750 mm, Weight: 12.500 kg Price: On request - Year: 2012 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 7336127126 - Operating hours: 25000 - Drive system: CNC - Control system brand: Cybelec - Control system type: DNC-880S - Power [kW]: 18.5 - Number of axes [pcs]: 4: Y1+Y2+X+R - Press force [ton]: 175 - Max. working width [mm]: 4050 - Column gap [mm]: 3600 - Max. stroke [mm]: 255 - Control type: DNC 880S - Control: CNC Credpfx Ajwmf Efeb Tjk - Transport dimensions: 5250mm x 2350mm x 2750mm (l x w x h) - Transport weight [kg]: 12500kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2002, fuel type: gas, Number of working hours 3184 h weight max. 8 t Crjdjwx R T Espfx Ab Tjk weight of the machine ca. 13400 kg