Bandsaw - Horizontal

EPPLE EPPLE BS 275 G

Condition: new, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, tire size: 245/70 R 17,5, color: grey, operation weight: 12,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Dcjdpfx Agohlz R Sevsh Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: good (used), Year of construction: 2007, machine/vehicle number: 195311, Offer 24601 Technical data: - Welding current max. 450 A 60% ED - 320 A 100% ED - Welding current adjustable in 3 coarse steps + 12 fine steps - 50 to 450 A - separate wire feed case with intermediate package 1 m - 4 roller wire feed continuously adjustable - 2 cycle + 4 cycle – regulation - Digital volt + amp display Djdpfxovt Trze Agvech - Spot welding - Interval welding - Water-cooled hose package 4 m - Ground cable - Pressure reducer - Connection 400 V / 50 Hz / 63 A - Space requirement approx. W 750 x D 1100 x H 1600 mm - Weight approx. 180 kg

Condition: used, Universal Tool Milling Machine DECKEL Type FP 1 Machine No. 51265 Year of manufacture: approx. 1967 Travel paths X: 300 mm Y: 150 mm Z: 340 mm Table size 600 x 200 mm Spindle taper SK 40 - S20 x 2 Spindle speed 40–2000 rpm, 16 steps Motor power 1.0 and 1.6 kW, pole-changing Power supply 380 Volt, 50 Hz - Feed on X and Z axes - Spindle speed via 2 motor speeds and 8 gear steps - Quill movement at vertical milling head 60 mm Dcodpeghtvaefx Agvoh - Swiveling, rotating, and tilting angle table - Coolant pump in machine base - Separate control cabinet Space requirements L x W x H 1100 x 1100 x 1600 mm Weight 690 kg In good condition

Condition: refurbished (used), Year of construction: 2011, Used automatic hydraulic bandsaw for metal MEP SHARK 332 NC EVO Blade dimensions: 3320x27x0.9mm Mitre angle: from 45° to +60° Operating modes: manual, semi-automatic dynamic, semi-automatic, automatic Cutting speed: 15-100m/min (inverter) Cutting capacity: at 0° - round 300mm - square 260mm - rectangle 330x260mm Dimensions: 2600x2320x2000mm Year of manufacture: 2011 Weight: 1050kg Dsdpfsul Svlex Agvech The machine is fully refurbished and tested.

Condition: new, Year of construction: 2026, CORMAK HBS275 band saw, equipped with a hydraulic cylinder, a cooling system and an arm swivelling up to 60º, together with blades from renowned German company Röntgen, is used commonly in ironworking, where precision, quality and cutting speed are essential. Horizontal band saw with a swivelling arm for cutting metals, allows for cutting in plane perpendicular to the axis of material cut and at any angle from 0 to 60º. Material for cutting can be fed manually or with any mechanical feeding device, with automatic tool feed. Band guides are equipped with dedicated carbide plates and bearings. This has a huge impact on band guiding, its durability, cut straightness, cutting accuracy and quality. Carbide guiding drastically reduces the wear of the machine and blades. Machine's arm made of uniform cast iron as well as a 27 mm wide cutting band are capable of low and high quantity cutting of profiles and other materials. The vice is located in an adjustable bed, equipped with a quick clamp. Blade guides have cemented carbide plates and roller bearings. Its these cemented carbide guides that provide cut precision and straightness. The arm, positioned at an angle of 25º, thus increasing blade durability. To the bottom of the arm a brush wire is attached, ensuring clean and functional brush. Machine's drive is transmitted through a worm drive. A 3-phase motor with 2 cutting speeds and motor thermal protection. This cutting machine also has a strain gauge - a band tension sensor and an automatic switch-off in case the cutting band breaks. Upper part of the base constitutes a tank for flood coolant draining and chips produced during cutting. A cast iron workbench is attached to the base, with a swivel arm and control panel on separate arm. The main cutting move in the cutting process is moving the cutting band and the arm lowering feed. The arm lowering speed (the cutting speed) is adjusted with the hydraulic cylinder. The feed speed is controlled by the control panel. There are 2 cutting band speeds to choose from: 37.5 and 75 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Total power 1.5 kW Power supply 400V 50Hz Arm lowering control hydraulic cylinder Band dimensions 2455 x 27 x 0.9 mm Band speed 37.5/75 m/min Vice base height 900 mm Weight 215 kg Angle 0º ø220 Dcsdpfx Asudi Unegvjh 260 x 140 200 x 200 45º R ø160 160 x 140 160 x 160 60º R ø100 120 x 100 100 x 100

Condition: new, weight max. 10 t Dcodpfx Agof Ep Dijvsh workpiece diameter 100 - 3200 mm drum diameter 300 x 120 mm feed 100 - 1000 mm/min total power requirement 2 x 0,55 kW

Condition: excellent (used), Year of construction: 1955, Drilling capacity in steel St 37 Ø 65 mm Drilling capacity in cast iron Ø 75 mm Spindle mount MT 5 Throat 1250 mm Spindle stroke 400 mm Dedpetwzk Dofx Agvjch Spindle speeds 22.4 – 1800 rpm Feed range 0.056 – 0.56 mm/rev Column diameter Ø 300 mm Motor power, 2-stage: 3.6 / 4.8 kW Clamping surface, base plate 1320 x 1000 mm Dimensions L x W x H (with motor!) 2250 x 1000 x 3100 mm Transport dimensions L x W x H (without motor!) 2250 x 1000 x 2800 mm Weight 5100 kg Accessories / Special features: • Cube table L x W x H 650 x 500 x 500 mm • Central clamping • Feed • Right-to-left travel • Motorized up and down travel • High speed range up to 1800 rpm • Coolant system • Lighting Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 D - 44143 Dortmund - Wambel

Condition: used, Year of construction: 1990, sheet width 3050 mm plate thickness 12 mm distance between columns 3100 mm table height over floor 900 mm cutting angle adjustment 0,5 - 3 ° Djdpfxju Uu Smj Agvsch no. of strokes 6 - 13 Hub/min back stop - adjustable 1000 mm down holder 18 St oil volume 350 l total power requirement 22,5 kW weight of the machine ca. 8 t dimensions of machine L x W x H 3,96 x 2,10 x 2,22 m - with adjustment of cutting gap - Accessories: electr. back gauge, spare knives

Condition: used, Year of construction: 2014, machine/vehicle number: 0102-260010, The Behringer HBP413A bandsaw automatic is an economical metal bandsaw for automated 90° cutting operations in industrial production. The HBP413A bandsaw automatic offers a cutting range for round material from 10 mm to 410 mm and for flat material from 10 x 8 mm up to 500 x 400 mm, with a saw blade dimension of 5,800 x 41 x 1.3 mm. The frequency-controlled saw band drive has a motor power of 5.5 kW and offers steplessly adjustable cutting speeds from 20 – 140 m/min (66 – 459 ft/min). The cutting speed can be set and monitored on the control panel. The total drive power is approx. 7.5 kW. Special equipment: chip conveyor, micro-dosing unit, and vertical bundle clamping device at the feed gripper and in the sawing area. Dcedjy D Immepfx Agvoh

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Bandsaw MACC SPECIAL 411 CSO, year 2019 Condition: very good - Sawing machine with cutting band falling controlled by hydraulic - Vice closure operated manually - Manual head return - Vertical rotation on bolt with adjustable tapered bearings without backlash - High-capacity band control by two-speed motor and special reducer with bronze gear tempered and ground worm screw - Blade tensioning obtained per manual rotation of the handwheel and guaranteed by microswitch - Vice with device for quick approach - Accident-preventing devices on flywheel casing, on control handle, on blade, and external guard - Hydraulic cylinder for controlled descent - Cutting thickness 1,2 mm - Cutting range 45° left 60° right - Adjustable end stop for cuts of the same size - 24 V low voltage control - 0,06 kW power-driver pump for band cooling - Pedestal with chip collection tray and removable tank for coolant Djdpfx Ajpmaubogvoch - Inlet conveyour