Vessel Turning Unit

DUMETA D-CHGK-5-D

Condition: new, weight max. 5,0 t workpiece diameter 100 - 2500 mm total power requirement 2 x 0,37 kW load capacity drive unit max. 2500 kg load capacity rotating unit max. 2500 kg table turning speeds 100 - 1000 mm/min Gusdpfx Ansgvwgcsksb diameter of running wheel 250 x 140 mm weight of the machine ca. 0,9 t Incl. double foot pedal (start-stop / left-right) Incl. remote control (on the cable)

Condition: new, Bernardo horizontal bandsaw HBS 275-400 V Technical specifications Cutting capacity round 90 ° and 225 mm Cutting capacity 90 ° 200 x 200 mm square Section flat 90 ° 245 x 150 mm Cutting area around 45° 160 mm Section square 45 ° 160 x 160 mm Cutting area around 60 ° 100 mm Cutting range, square 60 ° 100 x 100 mm Working height 910 mm Band saw blade dimensions 2480 x 27 x 0,9 mm Cutting speeds of 400 V 45 / 90 m / min Coolant pump S1 100% 100 W S1 motor power output 100% 1,1 kW Motor power S6 40% 1,5 kW Voltage 400 V Machine dimensions (L x D x H) 1430 x 720 x 1700 mm Weight approx. 190 kg Scope of delivery • Band saw blade • Workpiece stop • Base • Belt tension gauge Guodpfsd Du T Isx Ankjb • Vise with quick locking • Coolant system • Hydraulic lowering cylinder • Motor protection switch • Automatic shut-off

Condition: new, weight max. 5 t workpiece diameter 100-2500 mm gear diameter 250 mm gear width 140 mm total power requirement 0,8 kW Guodpfxefv A Axj Anksb weight of the machine ca. 0,8 t dimensions of the machine ca. 2,0 x 1,4 x 1,0 m

Condition: used, Year of construction: 1984, x-travel 2500 mm y-travel 750 mm z-travel 1000 mm table surface area 2550 x 800 mm spindle taper SK 50 control HEIDENHAIN, TNC 150 B Gedpfetqqnwsx Ankoub weight of the machine ca. 16 t

Year of construction: 2022, condition: new, Load capacity: 10.000kg Speed: 0.03- 1.6 rpm faceplate diameter: 1.500mm, expandable to 2.500mm welding current transmission: 800A Guodpfxjfxgp Ue Anksb

Condition: new, Year of construction: 2024, machine/vehicle number: 302340, Profile Bending machine KB Türkei model MB 30 bottom shaft 30 mm top shaft 35 mm two rollers driven with basement Gusdod S Uf Sspfx Anksb capacity: up to round tube 48 x 3,0 mm flat material 50x10 mm square tube 40x40x3,0 mm weight 170 kg motor 0,75 kw 400 Volt 50 Hz 3 ph.

Condition: used, Year of construction: 1987, pressure / t stroke / mm table-size / mm weight of the machine ca. 65000 kg Make: Shepherd Type: SVRM 4-roller bending machine: Gjdouddcajpfx Ankeub Year of construction: 1986 Working width: 3000cm Smallest pipe diameter with 600 mm roller: Ø 720 mm Smallest tube diameter with 360 mm roller: Ø 460 mm Sheet thickness up to (depending on the material): 50 mm Material SA- 738 B Working width: 2500 mm Material SA- 738 B Material thickness: 35 mm conical bending: Except for the top roller, all rollers can be moved in an inclined position for conical bending. The roller positions can be read on display instruments. For semi-automatic or fully automatic operation of the machine, the bearing jewels of the rollers are equipped with scale bars and slide cams for limit switch actuation. This allows the rollers to return to the same set position over and over again, giving a very high level of uniformity in the shot wefts being bent.

Condition: new, capacity 90 degrees: round 240 mm capacity 90 degrees: square 240 mm 165 x 310 mm saw band length 2725 x 27 x 0,9 mm mm Gjdpfx Anjhpktvjkoub table height 890 mm band speed 35 / 70 m/min total power requirement 1,1 kW weight of the machine ca. 0,35 t Dimensions (LxWxH) 1,7 x 0,75 x 1,8 m The Z252/DG has the following equipment: - hydraulic cylinder, - emulsion pump, - eccentric clamp, - base, - saw blade, - 400V plug -16A- The machine is delivered fully assembled and ready for immediate use.

Year of construction: 2004, condition: excellent (used), Four-side planer -max. planing width 23cm -max planing height 16cm -2 pulling rollers in the table -chromed table - smooth regulation of the feed speed -2 pulleys from the top in front of the lower head, additionally a roller apparatus for short elements - 4 spindles: lower 5.5kW, right 5.5kW, left 5.5kW, upper 7.5kw Gujdpshlp D Njfx Anksb The machine is in very good condition, little used, with spiral heads on the bottom right and left, with a Terssa knife head on the top.

Condition: new, Year of construction: 2022, feed rate X-axis: 20 m/min, feed rate Y-axis: 20 m/min, feed rate Z-axis: 15 m/min, overall weight: 7,400 kg, spindle speed (min.): 4,000 rpm, spindle speed (max.): 10 rpm, travel distance Y-axis: 1,500 mm, power: 22 kW (29.91 HP), DYAS Plate Drilling Center - DYAS PDC-1500 Guodpfjgbfaxsx Ankjb Number of Drilling Units 1 Vertical Motor Power 22 kW Spindle Torque 280 Nm Spindle Speed 10-4000 RPM Automatic Tool Changing (ATC) 16 Units Maximum material weight 760 kg Max. Max. Drilling Capacity (mm) Ø40 mm