Profiling scaffold, scaffold stand

Dreistern P3.100

Condition: used, sheet thickness steel (max.): 2 mm, total width: 250 mm, Profiling line Dreistern P3.100 with mobile cut-off unit and accessories Machine bed features: Production direction: right to left Axle distance: 330 mm 48 stations 44 stations can be driven (44 gearboxes) Quick-change plates Mechanical quick-release clamps Coolant piping 1 x 42 kW Baumüller motor 1 x 15 kW Baumüller motor Profiling frame features: Tool width per frame: 275 mm Working shaft diameter: 50 mm Working shaft connection: 30 mm with keyway Fixed lower shaft (6 pieces with adjustable lower shaft) Axial adjustment Adjustment range of lower/upper shaft: 80 - 170 mm Gearbox features: Worm gear ratio 1:21 Lower/upper shaft gear ratio 1:1 Mobile cut-off unit features: Travel distance: 1900 mm Profile rail guidance Ball screw drive Bosch servo motor Ppsdpfjy Sm Eqjx Amyjw Valve block with punching unit Folding table length: 3000 mm Emergency stop Scope of delivery: Machine bed with gearbox support Infeed table Measuring wheel unit, pneumatic Straightening device Strip filter unit 800 liters Hydraulic unit for separator 44 gearboxes 44 profiling frames 2 Baumüller DC motors 66 universal joints The system operated flawlessly in production until it was dismantled at the customer's facility. Control system not included. Strip unwinder and perforation unit are also available from us as used machines. The system can also be easily extended with additional stations. We can support you with the following when reassembling the system: Planning Mechanical overhaul Control system construction Painting Safety concept CE documentation

Condition: new, Year of construction: 2026, PROFESSIONAL WIRE FEEDER WITH AC SERVO MOTOR FOR LASER AND TIG WELDING Citronix professional wire feeder with servo technology - means that it uses ac servo motor for motor drive, which enables it not only to feed wire very precisely even when the speed is low, but also the ability to set the length in „mm“ for wire withdrawal, and also, after the material is cooled down, we can push it again (the smallest step 0,1 mm) This is a very important feat with laser welding, and this working method is an advantage compared to wire feeders made in the Far East, since with those machines the function of withdrawal and pushing the wire is set on time, and the consequence of this method is that the tip of the welding wire never comes back to the place where the withdrawal started. We made the Citronix wire feeder in a way that it can control not only the wire feeding process, but it can also manage (turn on and off) both the laser source and the gas magnetic valve. This is another significant difference and advantage compared to other manufacturers, because usually there is no spot welding technology in laser welding machines, so if someone wants to weld sheets in the spot welding technology, he can set the spot time and the wire feeder will control the laser source. Wire feeder has 4 operation technologies: 1. continuous welding with wire feeding; 2. continuous welding without wire feeding; 3. spot welding without wire feeding; Wire feeder has 200 memory cells – locations, if the parameters are set, they can be saved on the memory location and we can name them in any number or text combination, in order to make use easier. We also developed a foot pedal, which can be attached to the wire feeder and regulate the feeding speed. It works like a gas pedal in motor vehicles. If, for example, we set the maximal speed 10 meter per minute on the display, and press the pedal all the way, the speed will be 10 meter per minute (or the speed we set), if pressed only half way, the speed will be half of the set speed. This feat can be used if the operator remains in one place, for example if he is sitting. If this pedal isn't necessary, the wire feeder can be attached to the system in a manner to turn on-off the welding process from the button on the torch. This pedal is optional, and in case you want to order it, it is additionally charged 400 EUR. Take a look at the monitor images and see the functions – parameters that can be adjusted. Citronix wire feeder can be used not only for laser welding, but also for the TIG welding, we made a filter to prevent HF-spark. Wire thickness it can push is from 0,8-2,4 mm. At this moment, we have a menu in English, German, Hungarian, and Serbian language. In our offer we have a lot of welding machines we developed ourselves and they are all digitally and software based MIG MAG, MIG PULS SYNERGIC welding machines, also for robot welding with touch screen monitor, TIG ac dc with touch screen monitor, digital plasma cutting machines, electronics for controling the high pressure water jet pump, sand dispenser for water jet cutting, voltage THC with touch screen monitor... Psdjmk S Slopfx Amyepw We are also very involved in innovation and development, please take a look at our other products, if you are a manufacturer, and are interested in discussing further, we are also selling know-how.

Condition: used, sheet thickness steel (max.): 2 mm, total width: 250 mm, Roll Forming Line Dreistern P3.100 with Accessories Machine Bed Features: Production direction: right to left Centre distance between axes: 330 mm 22 stations 18 driven stations (18 gearboxes) Quick-change plates Mechanical quick release clamps Coolant and lubricant piping 2 x 18.5 kW Bosch motors Roll Forming Stands Features: Tool width per stand: 275 mm Working shaft diameter: 50 mm Working shaft connection: 30 mm with keyway Fixed lower shaft Axial adjustment Adjustment range lower shaft to upper shaft (UW-OW): 80 - 170 mm Gearbox Features: Worm gear ratio 1:7.5 Lower shaft to upper shaft ratio (UW-OW): 1:1 Scope of Delivery: Machine bed with gearbox carrier Infeed table Measuring wheel unit, pneumatic Special straightening unit 18 gearboxes 18 forming stands 2 Bosch motors 36 drive shafts The machine was running flawlessly in production until it was dismantled at the customer's site. Control system is not included. Decoilers and punching units are also available as used machines. The line can be easily extended with additional stations. We can support you with the reassembly of the line, offering: Psdpfx Asy Sm A Asmyjpw Planning Mechanical overhaul Control system construction Painting Safety concept CE documentation

Condition: used, sheet thickness steel (max.): 2 mm, total width: 250 mm, Profiling Line Dreistern P3.100 with Accessories Machine Bed Features: Production direction: left to right Center distance: 330 mm 18 stations 16 powered stations (16 gearboxes) Quick-change plates Mechanical quick-release clamps Coolant piping 2x 18.5 kW Bosch motors Profiling Frames Features: Tool width frame: 275 mm Working shaft diameter: 50 mm Working shaft connection: 30 mm with keyway Fixed lower shaft Axial adjustment Adjustment range lower to upper shaft: 80 - 170 mm Gearbox Features: Worm gear ratio 1:7.5 Lower to upper shaft ratio 1:1 Scope of Delivery: Machine bed with gearbox support Infeed table Measuring wheel unit, pneumatic Special straightening unit 16 gearboxes 16 profiling frames 2 Bosch motors 32 cardan shafts The machine was working flawlessly in production until dismantling at the customer's site. Control system not included. Coil decoilers and punching units are also available used. The line can easily be extended with additional stations. We can support you with reassembly of the line: Psdey Sm Apjpfx Amyjpw Planning Mechanical overhaul Control system construction Painting Safety concept CE documentation

Year of construction: 2004, condition: excellent (used), 3D coordinate measuring machine in a stand-alone design *Floor-mounted installation on steel feet *Height from floor to measuring plate: 600 mm Measuring range *X 3,200, Y 1,600, Z 1,800 [mm] Measurement uncertainty *30 + L/40, max. 60 [µm] at L = 3,000 mm Dynamics *3D traversing speed: 220 mm/sec *3D acceleration: 1000 mm/sec² Probing system *Renishaw PHS / alternatively PH10M *Renishaw TP20+2 modules Control system *Pantec Eagle Pro Wireless control unit *Handheld control unit HT400 Software Ppsdpfx Amehlqknjyew POLYWORKS Inspector Optional technologies Probe changer MCR20 Probe changer ACR3 Optical scanner KREON or NIKON Supplier’s services Transport, commissioning, calibration, final acceptance Warranty 12 months, from the date of acceptance

Condition: used, material width:304,8 mm material thickness:0,12 - 2,2 mm feed length:304,8 mm clamping force of fastening pincer:850 N Pedpfxscxxrxj Amyspw clamping force of moving pincer:4410 N feeding force:650 N weight of the machine ca.:0,15 t dimensions of the machine ca.:0,7 x 1,05 x 0,6 m

Condition: used, Year of construction: 1984, machine/vehicle number: 220-3, Ref. No. 25304 Technical Data: - Machine for producing longitudinal seams on the edges of square or rectangular long ducts - Number of roller shafts with seam rolls: 15 pcs - Material thickness: from 0.5 to 0.63 mm Pjdpfx Amow U Rb Heyepw - Duct dimensions: from 80 x 80 mm up to 100 x 100 mm - For duct dimensions from 100 x 100 mm - Material thickness: 0.5 to 1.0 mm - Feed speed: 15 m/min - Pneumatic connection - Drive: 400 V / 3 kW - Includes: - Foot switch - Duct guide plates - Separate lubrication system - Space requirements: approx. W 5400 x H 1200 x D 800 mm - Weight: approx. 950 kg

Condition: new, Fully automated roof tile profiling machines available in various sizes and designs. Our range includes over 60 roof tile patterns. Delivery time and machine configuration are determined individually for each order. Please contact us for further information and technical documentation. Ppedsyu Sz Iepfx Amyew

Condition: used, sheet width 3200 mm plate thickness 2,5 mm weight of the machine ca. 3,5 t Pjdpfx Aer Ngtfemyepw Tools recentely grounded. Bending angle preselection via potentiometer

Condition: used, Year of construction: 1973, machine/vehicle number: 104530, pression: 100 t throat: 350 mm table size: 690 x 840 mm clearance hole in the die: 160 mm Ø tappet area: 450 x 600 mm Ppodpfxeddhw Sj Amyow tappet adjustment: 80 mm stroke adjustment: 8 - 100 mm number of strokes: 60 /min engine: 380 V, 5,5 kW space needed: 1850 x 1850 x 2650 mm weight: 6800 kg