Trolley for carriage of sashes and frame

COMALL CARR 600 - 85/9 Q

Condition: ready for operation (used), Year of construction: 2018, Machining sides: 3, workpiece materials: aluminium/steel, travel X: 4000mm, feed rate: 120m/min, A-axis: +/-110°, spindle speed: 18000rpm, tool holder: SK30, tool positions: 8, max. profile dimensions X/Y/Z: 4000mm/250mm/190mm, machine dimensions X/Y/Z: approx. 5750mm/2100mm/2350mm, weight: approx. 4000kg, control: Mecal. Documentation available. On-site inspection is possible. Gsdpfoyh Nv Hex Ankjub

Condition: refurbished (used), Year of construction: 2024, Manufacturer: Elumatec Type SA/ SAS 142 Overhaul year: 2024 Saw blade max. carbide: 500 mm Drive power saw motor: 4 KW Gedpfxsuiy Nyo Ankeub Saw motor speed: 2800 min-1 Cutting speed saw blade 500 mm: 4400 m/min Saw height control: infinitely variable, fully electronic Working range square 90° max.: 130 x 130 mm Working range flat: 90° max.: 190 x 130 mm Working range round: 90° max.:150 mm Pneumatic feed length: 5-560, 10-1120 mm Compressed air connection, on site 6 bar Weight(saw)approx.: 800 kg Dimensions LxWxH (saw)approx.:2900mm x 1400mm x 1500mm Installation area LxW: 2900mm x 1400mm Additional description Elumatec SA/ SAS 142 4KW Retrofit Elumatec SA 142 4KW Retrofit Fully automatic sawing machine for non-ferrous metal and plastic After completion of the retrofit, the machine is in mint condition, both technically and visually. The machine will be overhauled in our company at the customer's request. Among other things, the following points were renewed: - Conversion to Siemens S7 PLC control - Conversion to Siemens HMI control panel - New electrical components - New pneumatic lines - Maintenance or replacement of all pneumatic cylinders and valve terminals - Maintenance of minimum lubrication system - Replacement of general wear parts - Overhaul of the cab Warranty: Unless otherwise agreed, we provide a 6-month warranty on all parts overhauled or replaced by us. Working time and wearing parts are excluded from the warranty. Optional: - Extension of the sawing area to flat 90° max.: 300 x 120 mm - Splitting extension (for a high-quality cut surface without return marks) - Servo-controlled material feed - Saw blade feed Servo-controlled - Mass clamping device Feed vice - Delivery and installation on your premises - Training of your employees

Condition: used, • Load capacity 350 kg Guodpfoxnvq Esx Ankjb • 6 vacuum suction cups, 250 mm diameter, adjustable • Vacuum lifter can rotate 90° and tilt 90° • Suction cups with guide tube and electric trolley • 4 units available, brand new and unused • Immediately available IV: + Design Standards 1. The construction of the unit strictly complies with European CE standard EN13155:2016, American ASME (Mechanical Engineering Association) B30-20-2006, and German UVVI8 regulations. The key design parameters exceed the requirements of the aforementioned standards. 2. Safety factor: The main structure features a factor of 4.0, vacuum safety level is 65%, and the standard safety level is 85%, which is 20% above the standard safety requirement. V+ Equipment Inspection and Standards 1. General Check that all materials are complete, inspect if the equipment exterior is painted or scratched, check for damage to the suction cups and pipes. 2. Pre-shipment Inspection © Equipment suction test © Equipment pressure holding test © Alarm system test © Various control components • Price on request

Condition: new, Year of construction: 2026, functionality: fully functional, A sliding table saw for working with high density boards, MDF boards, ABS and PVC panels, solid wood and other wood-based materials of similar structure and hardness. The saw is designed for small and medium carpentry work. Gjdpfxotz Smis Anksub Strong, professional sliding table saw with a movable table on bars and a separately powered scoring. Saw tilts in the 90–45 degrees range Solid, durable design ensures stability and work safety Controllable speed adjustment Technical data Table dimensions 970×550 mm Sliding table length 3200 mm Cutting width by the fence 1200 mm Transverse cutting by the transverse cutting guide 3100 mm Saw tilt 0°–45° Saw diameter Ø350 mm Saw hole diameter Ø30 mm Saw blade height 0–87 mm Saw blade 350 max height 105 mm Saw blade height at 45° angle 0–60 mm Saw blade 350 max height at 45° angle 73 mm Main saw spindle speed 4000 / 6000 rpm Scoring saw diameter Ø125 mm Scoring saw hole diameter Ø20 mm Scoring speed 8000 rpm Main motor power 5.5 kW Scoring motor power 0.75 kW Intake connector under table diameter 100 mm Intake connector diameter in the saw guard 80 mm Machine weight 680 kg Available equipment Cutting saw Scoring Transverse cut fence Longitudinal fence Modern - ergonomic saw guard Worktop extension Fence for mitre cutting Saw blade tilt gauge indicator User manual EC declaration of conformity

Condition: used, Year of construction: 2023, DOUBLE GLASS BEAD SAW TRF 527 VIS CE 1 pc DOUBLE GLASS BEAD SAW TRF 527 VIS CE TRF 527 VIS: Double miter saw for the simultaneous cutting of two glass beads positioned one above the other. The right saw unit is fixed, adjustment of the left unit is via the set cutting length can be read off a digital display. The units have supports that allow two glass beads to be cut simultaneously. The upper support can be removed for cutting larger cross-sections. After the cutting process is completed, the pneumatic clamping cylinders automatically swing to the side to simplify loading and unloading of the machine. STANDARD EQUIPMENT • Fixed unit on the right • Digital dimension display • Pressure switch • 2 HM-tipped saw blades • Electrical system with motor brake, undervoltage release, motor protection switch • Pressure switch • Tool set • Guards with horizontal clamping devices, pivoting • Two-hand control • Belt drive • Pneumatic unit lift • Middle support TECHNICAL DATA • Motor power 2 x 1.2 kW • Saw blade diameter Ø 220 mm • Max. cutting height without support 80 mm • Max. cutting width at 90 degrees 55 mm • Max. cutting width at 45 degrees 40 mm • Max. cutting length 2800 mm (optional 4000 mm) • Min. cutting length 158 mm • Weight 217 kg • Space requirement (standard equipment) 3000 x 850 mm Extended cutting capacity 1 pc Maximum cutting length • 4000 mm Star stop 4 positions 1 pc set 2 mechanical stops for adjusting up to 4 intermediate angles. Additional center support. 1 adjustment for rebated profiles. 1 adjustment for rebated profiles as per drawing: - Attachment to the clamping devices to compensate for the profile inclination - Allowances on the rear stops of the units and the center support. The sketch below shows (in green) a beveled presser that follows the inclined profile and presses it against the allowance on the stop (shown in red). Storage location: Garbsen Gedpfexnlgcsx Ankeub

Condition: good (used), Year of construction: 1992, Single-piece sanding machine sanding from top and bottom electric height adjustment with digital display continuously variable feed speed star/delta starter pneumatic belt tensioning main switch sanding belt oscillation finishing brush unit top and bottom, manual height adjustment Working width: 190 mm Gujdpfx Answyda Uekeb Working height: 4 - 150 mm Min. workpiece length: approx. 280 mm Abrasive belt dimensions (L x W): 1850 x 200 mm Feed speed: 5 - 25 m/min Installed power: approx. 14 kW Extraction port diameter: 2 x 180 mm Dimensions (L x W x H): 2000 x 1000 x 2050 mm Weight: approx. 1800 kg Incl. infeed and outfeed roller conveyor (L = 1600 mm, non-driven) Note on used machines: • Technical data subject to errors and prior sale. • Quoted prices are ex-works – loaded free of charge! • The machines have been cleaned and function-tested. • All machines are sold as inspected, with no claims to warranty. Buyers are welcome to inspect machines at the location. • Special agreements are only valid in written form. (We answer inquiries only when your address and telephone number are provided!)

Condition: new, The ALTENDORF F 25 offers everything in a small space, what a sliding table saw must be able to do. Whether in the first own workshop, for daily use, in industrial production Gsdpfx Asu R S Hcsnksub industrial production or as a powerful second machine. - The F 25 is the space-saving all-rounder that simply makes you simply makes you more productive. Materials such as wood panel materials, solid wood, wood-like materials or extruded or extruded profiles can be cut with the best precision, easy handling and outstanding cutting quality can be easily processed. The one-sided swivel saw blade also enables angled cuts. The smooth-running double roller carriage based on the Altendorf as well as the digital display of the height and tilt are standard features. A machine for beginners and professionals alike. Double roller carriage, tiltable, man. Height and swivel adjustment, Rip fence with man. Fine adjustment, angle mitre fence, Preparation for retrofitting, of a scoring unit ----- Technical data ----- Swivel range: 0 - 46 °, carriage length: 3,200 mm, Cutting width: 1,000 mm, Cutting height: 100 mm, max. saw blade Ø: 315 mm, max. saw blade projection: 104 mm, Non CE version: max. saw blade Ø: 350 mm, max. saw blade projection: 121.5 mm, Crosscut fence extendable up to: 3,450 mm, speeds: 4,200 rpm, Motor power: 4.4 kW, 5.5 HP, work table height: 880 mm - large extraction hood is optional - - new exhibition machine -

Condition: used, cut-off saw 3 KW Spindle diameter 50 mm Spindle length 300 mm Number of tools variabel St. Control CNC Dimensions (L/W/H) 2500x1700x2100 mm weight 1700 kg HABERKORN - FZS-2 Electronic Slotting Machine with Stepless Slotting Spindles and Automatic Roller Table ----- Crosscut Saw ----- Spindle Positioned at the Top Three-Phase Motor 3 KW Spindle Diameter 30 mm Gsdpfowgwlkex Anksub Speed ??2800 rpm Saw Blade Diameter 400 mm * Automatic Brake with Speed ??Monitoring * Stepless Saw Positioning with Siko Display * Guard and Extractor Hood with 100 mm Diameter Extractor Nozzle 2 Slotting Spindles 50 mm Diameter ----- Power 2 x 7.5 KW Speed ??4200 rpm Spindle Diameter 50 mm Max. Tool Diameter Approx. 360 mm Usable Length 300 mm * Both slotting spindles can be positioned via ball screw * Freely programmable 19 programs, display with function keys * Protective and extraction hood with 180 mm diameter extraction nozzle * Automatic brake with speed monitoring Studio table ----- * Swivel range +/- 65° * Automatically changing counter wood (programmable) * Pneumatic clamp * High-precision electrical degree indicator * Automatic length compensation * Counter wood at any angle setting in the cutting plane Special features ----- Continuously adjustable roller table feed Laser for workpiece positioning Manual length stop LA 2000 Length 2500 mm Extraction nozzle diameter: 2 x 180 mm for slotting spindles 1 x 100 mm for crosscut saw ----- Price of the above-mentioned machine upon request! ----- Images show the same model. Original images not yet available. (Technical specifications according to the manufacturer - no guarantee!) All prices quoted are net, plus statutory VAT.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SÇ 901 S Pnömatik Alüminyum Köşe Presi Makinası, - Conforms to CE standards - Corner press machine designed for 90 degree joining of aluminum profiles - 2 top presses and blade movement is pneumatic - There is a mm ruler system for the height and advancement of the blades. - Centering miter wedge is automatic Godpfx Ajrbiv Aonksub - Drain button available for fine adjustment - Pneumatic presses use 2 pedals to squeeze the profile - Profile surfaces are polyamide sheet to prevent damage - Side support arms available

Year of construction: 2012, condition: excellent (used), Used Ras 62.25 CNC Folder Model: 62.25 Ras Year 2012 RAS 62.25 CNC folder Gsdon Tnzfjpfx Ankoub Capacity: 2540mm x 2.5mm CNC Auto Bending Machine (Year 2012) Complete with fitted System 6000 Touch screen control (screen recently replaced) 3.2 Metre J shape back gauge Twin Foot Pedal Control MACHINE GUARD SOLUTIONS Light Guards Complete with segmented and straight tools