Press brake

Bystronic Xpert 150 x 3100

Condition: ready for operation (used), Year of construction: 2001, pressure 50.0 t chamfer lenght 2090 mm distance between columns 1665 mm column arm 400 mm table width 60.0 mm ajustment speed 100 mm/sec working feed 10.0 mm/sec return speed 92.0 mm/sec stroke 200 mm table height 910 mm dayligth 470 mm Number of working hours 36.160 h total power requirement 6.0 KW weight of the machine ca. 4850 kg range L-W-H 3458 x 2450 x 2450 mm with only approximately 36.160 operating hours (!!) - Inspected condition - Machine video - ?v=x8Z0h2_wA6s Equipment: - CNC electro-hydraulic press brake - CNC control type OPERATEUR 2 with 8 axes (X1+X2, Y1+Y2, R1+R2, Z1+Z2) * CNC-controlled backgauge adjustment (X-axis) * CNC-controlled vertical adjustment of the stop fingers (R1+R2) * CNC-controlled left-right adjustment of the stop fingers (Z1+Z2) * Hand control unit for manual axes movement * Pivoting control, front left - AMADA/PROMECAM quick clamping system for the upper tool * 1 split set of offset upper tools (UKB 10.512) - AMADA/PROMECAM bottom tool holder * 1x split set of 1-V dies (UKB 20.810) - Side guards (hinged doors) - Rear guards (hinged door) - CE marking - 1x freely movable double foot switch - Operating instructions (PDF) Nksdpfx Aexabutshvou

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Nsdpfx Aswu Tu Dshveku Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, measuring range X-axis: 1,200 mm, measuring range Y-axis: 2,000 mm, measuring range Z-axis: 1,000 mm, Measuring Range X – axis 1200 mm Y – axis 2000 mm Z – axis 1000 mm Accuracy acc. ISO 10360 E = [2,6 + 4L/1000]µm Nkedpfx Aodv I Abshvou DCC controller Renishaw UCC S5 JS box Renishaw MCU-5 (wireless on demand) Temperature sensor Renishaw Probe system Renishaw REVO 5-axis scanning probe Probe changer Renishaw (price REVO system new appx. € 80.000,--) Application software Inspect3D Inca V6 avzula version built 2014, retrofit 2017 with Revo

Condition: ready for operation (used), Year of construction: 2013, sheet thickness steel (max.): 25 mm, power: 6 kW (8.16 HP), Working area 3000x1500. Loadmaster system included.Due to not using machine for longer time,the service is required. Nkjdpfxewh R R Ns Ahvju

Condition: as good as new (ex-display), Year of construction: 2022, Press design double column press Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 4000 kN Free ripping force max. 400 kN Nedjph Uk Njpfx Ahvoku Pressure build-up time Closed die steel to steel Max. 4 sec. Dimensions 3,800 mm long and 4,475 mm wide Max. Opening width 800 mm Stroke 800 mm Table height above floor 1100 mm Height above floor (headroom) approx. 4300 mm Hall height min. 5500 mm parallel deviation at 20°C +/- 0,1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of press without operating materials and table plate approx. 28 t Press table Table size 1500x1500 mm Speeds Fast closing with 100 mm sec. Pressing speed 8 - 3 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Hydraulics Number of pressing cylinders/driving cylinders 1 pc. Operating pressure max. 300 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 3 bar Main pump BOSCHREXROTH axial piston pump approx. 145 L/min Oil volume approx. HLP 46 MW 1000 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Auxiliary pump BOSCHREXROTH, gear pump 10 L/min Pressure stabilization for up to 300 sec. Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Connection hydraulics main motor 40 kW Sliding table press with 400 T capacity, Closing speed up to 100 mm/ ( adjustable via touch screen ) Opening speed up to 100 mm/sec ( adjustable via touch screen ) Starting press speed 10 mm/sec ( adjustable via touch screen ) table top size 1500x1500mm ram size approx. 1600x1500mm Oil temperature monitoring 55 degree warning, 60 degree shutdown Automatic lubrication ( adjustable via touch screen ) Free positioning of the ram ( adjustable via touch screen ) SICK/PILZ light barriers 14 mm, front, up to 1800 mm height Hydraulic and mechanical ram protection Circuit oil cooling ( adjustable via touch screen ) Ejector in table, 20 T press force, 350mm travel Ejector moves outwards with the table Table plate milled flat, with DIN 22 T grooves Pressure adjustment from 60 T to 400 T ( adjustable via touch screen ) Travel limitation either by pressure or position Set-up mode, single stroke and cycle sequence ( adjustable via touch screen ) Swiveling control panel on the cabinet Two-hand operation, with opening button, manual/single stroke/cycle switchover button Installation, commissioning, instruction against separate charge The control is supplied by SIEMENS. ( S 7 1200 ) Also the touch screen monitor with 9 inch. The remote maintenance unit SECOMEA -Ethernet is included in the delivery. The side of the press has two 1000 mm high and 800 mm wide windows with double doors. (sliding table press, hydraulic press, hydraulic press, double column press)

Condition: new, DESCRIPTION DM100 Z2C - performs edge rounding and removes sharp burrs from both the inner and outer edges of steel, stainless steel or aluminium parts after laser, shear or punch cutting of metal parts from 50 x 50 mm up to 1100 x 100 mm in size. Ekdjtxp The 1st station processes the products through a contact roller (approx. 55° shore) with an abrasive belt and removes strong burrs in the first step. The 2nd station processes the products with 2 counter-rotating cross belts each from below and from above. The cross belts round off the parts to be machined on both the inner and outer edges. A big advantage is also the deburring of products with surface protection foil, because only the edges are processed without damaging the foil. Technical data - DM1100 Z2C: Working capacity (Ø mm) 1100x100 No. of belt stations (Z) 1 No. of cross belt stations 2 Abrasive belt, dimensions (mm) 1100x2200 Abrasive belt speed (m/s) 8-22 Cross belt speed (m/s) 2-8 Feed speed (m/s) 0.6-3.2 Sanding belt motor per head (kW) 18.5 Njdpfsd Ixadsx Ahveku Cross belt motor (kW) (2x) 3 Feed motor (kW) (3x) 0.18 Total power (kW) 33 Power consumption (A) 62 Rod suction connection per head (Ø mm) 150+185 Dimensions (mm) 3600x2330x2350 Weight (kg) 5000

Year of construction: 2008, condition: ready for operation (used), A Geiss large-format vacuum thermoforming machine is available. Panel cutting min.: 1100mm/1300mm, max. panel cutting: 2100mm/1800mm, max. forming depth: 620mm. Additional panel format 1: min.: 850mm/750mm, max.: 1850mm/1250mm. Additional panel format 2: min.: 1050mm/800mm, max.: 2050mm/1300mm. Including a separate loading machine with pneumatic panel separating equipment, an automatic aligner for panel cuts in longitudinal and transverse direction, a pneumatic pusher for removing the molded parts from the loading unit, fully automatic central lubrication of the loading machine, several interchangeable pallets for window panel sets, a storage rack for window panels as well as a vacuum control with four independently adjustable flow stages and an air preparation system. Documentation available. On-site inspection is possible. Njdpfxswih Are Ahveku

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, 🚨 FOR SALE: 2x Kardex XP500 Machines – Top Condition! 🚨 For sale for removal. We are building a new warehouse and do not require these units. In good condition, recently serviced, well maintained throughout the time we have owned them. Price is per unit, negotiable. Shelves can be easily reconfigured to accommodate different product types / sizes. Bins can be sold with machines if desired. Machines are currently configured for dual tray presentation. Also includes 10-bay Kardex SortBench. Details: Model: Kardex XP500 Quantity Available: 2 units Nksdpfxevuvbzo Ahvju Condition: Well-maintained and fully operational Key Features: High-density storage to maximize space utilization Fast and reliable picking system for enhanced productivity Built for heavy-duty industrial applications Ergonomic design to improve workplace safety Energy-efficient operation Why Kardex XP500? These machines are perfect for businesses looking to improve efficiency, save floor space, and boost order-picking accuracy. Location: The units are currently stored in Wanganui, New Zealand.

Condition: like new (used), Year of construction: 2017, TRUMPF TruDisk 5001 (6C) * MFD 2017, as-new condition * laser power: 5 kW * wavelength: 1030 nm * beam quality: 4 mm mrad * beam switch for 4 fiber exits, min. fiber diameter: 100 µm * fiber connector: LLK-D * option: field bus interface & IIO3-card * 2 identical lasers available Nedjqfguaopfx Ahvoku

Condition: used, Deburring and fine grinding machine for sheet metal / flat material, new The compact machining centre for deburring, slag removal, rust removal, oxide layer removal, edge rounding, fine grinding through to polishing metal surfaces. Nkodpfxonah Tao Ahveu Machine is suitable for heavy-duty use. Due to the fixed working height, this machine can also be optimally integrated into a production line and is suitable for machining large parts. Working width: 650 - 1650 mm Maximum part weight: 2000 kg Wide belts with abrasive belt unwinding: 3250 mm As standard with vacuum hold system, optional with magnetic hold system By using 3250 mm long abrasive belts, you get a uniformly smooth surface and reduce consumption costs, as these belts have a longer service life. Due to the modular design of the machines, it is possible to offer the optimal configuration for the customer's machining task. The machine structure can accommodate up to 5 internal machining units and 2 additional external machining units. The high rigidity of the machine structure and the feed table of this machine, combined with the advanced mechanics and electronics, make this series a universal machining centre for deburring and finishing. Please, contact us for getting more information and pictures on mail(at) or *