Belt sander

Bernardo MS 150 x 2000 S-2

Condition: new, Bernardo Belt Grinding Machine MS 150 x 2000 S-2 Tape dimensions 150 x 2000 mm Ijdpfx Aod Rw Rhsqusau Belt speed 14.5 / 29 m/sec. Contact disc x W 200 / 155 mm Flat grinding table 460 x 150 mm Suction connection of 100 mm Engine power S1 100% 2.1 / 2.8 kW Motor recording power S6 40% 2.8 / 3.6 kW Voltage 400 V Length 1080 mm Width 520 mm Height 1000 mm Weight approx. 85 kg

Year of construction: 1993, condition: used, TYPE : DEA 400/2000 Type YEAR : n.d. Year MAXIMUM SLEDGEHAMMER PRESSURE : TON. 400 Ram capacity SLIDING STROKE : mm. 1,100 Slide strok MAX VERTICAL LIGHT : mm. 1,600 Max shut height TABLE DIMENSIONS : mm. 2,000 x 1,600 Table size RAPID SPEED : mm/sec 650 Fast stroke TABLE PRESS CAPACITY : TON. 160 Cushion capacity PRE-MILER stroke : mm. 400 Cushion stroke HEIGHT ABOVE GROUND : mm. 5,800 Ground up to floor FRONT LIGHT : mm. 3,400 Distance btw uprights Iajdpfx Aqjihf R Ujusu LATERAL LIGHT : mm.1,600 Lateral window

Condition: new, width of the strips 150 mm band length 2000 mm band speed 14.5 + 29 m/sek grinding width 460 x 150 Plantisch mm Dust suction hood 100 mm total power requirement 4.0 kW 100% ED weight 84.0 kg range L-W-H 1080 x 520 x 1000 mm Standard with 2 speeds, ideal for grinding stainless steel properties - Good sanding performance due to high belt speed - Quick adjustment for horizontal and inclined position - Continuous flat grinding surface for optimal grinding of long workpieces - Constant belt tension through spring-loaded tensioning device - Universally applicable for grinding edges, surfaces and for cylindrical grinding - Including quick-release system for quick strap changes - Simple adjustment of the parallel belt run by means of an adjusting screw - Graphite coating on the flat grinding surface increases the sliding properties of the Sanding belt scope of delivery - Sanding belt K 80 - Hinged protective screen - Sanding and support table Iodpfsxabf Eox Aquoau - workpiece stop - Dust extraction nozzle - Separate off button - underframe

Condition: new, Year of construction: 2026, For sawing e.g. stainless steel, tool steel, hollow sections and solid materials Two-pole drive motor enables saw band speeds of 30 and 65 m/min Monitoring of saw blade tension electromechanically via microswitch When the saw arm is raised, the lowering cylinder locks in the upper position via the solenoid valve - additional locking at the cylinder is therefore not required Saw arm inclined by 25°, thus longer service life of the saw band Precise and robust band guides with adjustable HM plates Iodpfx Aeg U Uv Rjquoau After completion of the cutting process the saw band stops automatically in the lower end position Lowering of the saw arm by gravity or manually With infinitely adjustable, constant saw arm lowering speed via hydraulic cylinder Dimensions and weights length approx. 1200 mm width/depth approx. 650 mm height approx. 1800 mm Weight approx. 270 kg Electrical data Supply voltage 400 V Mains frequency 50 Hz Machine data Saw band speed(s) 30 / 65 m/min Speed levels 2 Saw band length 2450 mm Saw band width 27 mm Saw band thickness 0,9 mm Material feed Table height material feed 925 mm Cutting range 0° round (tube) 220 mm 0° round (solid material) 120 mm 0° rectangular lying (hollow profile) 230 x 150 mm 0° bundle (tube) 230 x 120 mm -45° round (tube) 160 mm -45° round (solid material) 85 mm -45° rectangular lying (hollow profile) 160 x 90 mm -60° round (tube) 90 mm -60° round (solid material) 55 mm -60° rectangular lying (hollow profile) 90 x 90 mm Art. No.: 3680001 S

Condition: used, Technical details: x-axis: 120 mm Isdpfowa A Hmjx Aqueau z-axis: 610 mm diameter: - mm measuring range Y-axis: Höhe: 0 - 610 mm weight: 19 kg interface: 2xRS-232C, 2xUSB-A/B total height: 950 mm measuring system resolution capability: 0,0001 mm power consumption: 43 Watt Floor Space WxD: 320 x 330 x H: 950 mm High-precision height measuring *

Condition: new, Year of construction: 2024, TECHNICAL DATA Iasdpfxjfpb Nmo Aquou Table size 1100 x 760 mm table height 870 mm milling spindle not interchangeable 30 mm clamping height 140 mm height adjustment 125 mm suction socket 2 x Ø 120 mm speed 3000 / 4500 / 6000 / 9000 rpm Colour RAL 7035 light grey and RAL 5000 violet blue Net weight approx. 800 kg TECHNICAL DESCRIPTION Solid German mechanical engineering Table milling machine with one-sided swivelling fixed milling spindle for swivelling range from -5° to +45.5 Positioning control for height and swivel adjustment with zeroing of the height and offset measurement travel Electronic position and speed displays 4 speeds 3000 / 4500 / 6000 / 9000 rpm Belt quick tensioning device Push button for spindle start and stop Left and right rotation Cutter quick clamping device Fine planed cast iron table with rigid frame support Control panel at the bottom of rigid frame support Milling stop 216 total adjustment via handwheel and LCD display incl. cast stop plates and aluminium splitter tongues Machine socket Lockable main switch Mechanical motor brake Milling protection and pressure device GAMMA V 1629 Curved milling fence 1639 Tapoa Milling spindle 30 mm, not exchangeable CE-conform GS tested

Condition: good (used), Year of construction: 2006, 1 used 4-axis horizontal machining center Brand Haas Type EC 1600 Year of manufacture 2006 Travel ranges X-axis 1626 mm Y-axis 1270 mm Z-axis 813 mm Spindle centerline to table 304 mm Spindle SK 50 Max. rated power 22.4 kW Max. speed 7500 rpm Max. torque 460.0 Nm 700 rpm Table size Length 1626 mm Width 914 mm T-slot width 16.00 mm T-slot center-to-center distance 125 mm Number of T-slots in standard configuration: 7 Max. load capacity on table (evenly distributed) 4536 kg Integrated 4-axis (B-axis) Table 1626 mm x 813 mm mm Clamping surface diameter 762 mm Adjustability 360° Max. workpiece swing diameter 1270 mm Table load 4536.0 kg Max. rated power 3.7 kW Rotational torque (continuous) 2712 Nm Backlash 30 arc-sec Gear ratio 500:1 Braking torque 5423 Nm Minimum resolution 0.001° Indexing accuracy ± 30 arc-sec Repeatability 15 arc-sec Rapid traverse rate on B axis 36°/sec Max. feed rate for machining on B axis 36°/sec Spindle centerline to table 146 mm Max. feed rate for machining in x, y, and z axes 12.7 m/min Rapid traverse rate on X axis 15.2 m/min Rapid traverse rate on Y axis 15.2 m/min Rapid traverse at Z 15.2 m/min Axis motors 30-station tool changer Max. tool diameter (full) 102 mm Max. tool diameter (adjacent positions empty) 254 mm Max. tool length 508 mm Max. tool weight 13.6 kg Tool-to-tool (average) 8.00 s Chip-to-chip (average) 12.60 s Isdsv N Di Aopfx Aqujau General information Coolant tank capacity 360 L Dimensions Domestic pallet 488 cm x 366 cm x 346 cm Export crate 488 cm x 366 cm x 348 cm Weight 13608.0 kg

Condition: good (used), Year of construction: 2014, Technical data shown on photos. Ijdpeufp Svofx Aquoau Parts shown by hand not come.

Year of construction: 1993, condition: good (used), machine/vehicle number: 03.2370, Arthur Klink - internal broaching machine (WAG 748) machine type: internal vertical hydraulic broaching machine manufacturer: Arthur Klink type: RISZ 10 x 1000 Iasdpfxocc D Dde Aqusu built in: 1993 stroke: 1000mm pulling force: 10.000KG working stations: 3 PCs drive: hydraulic system equipment: coolant system, magnetic chip conveyer remark: machine under power in stock the machine has an automatic workpiece loading system for 2 workpieces, ideal useable for high production Optional accessories available on request: tools, workpiece holder Information about us: we are specialized for second hand broaching machine and still have anytime about 80 pcs of used broaching machines in our stock, vertical and horizontal machines from 3000kg up 63.000kg pulling force and from 1000mm stroke up to 3500mm stroke.

Condition: new, Bernardo drill grinding machine DG 32 Pro Specifications Drill diameter 2 - 32 mm point angle 90° - 135 Speed 4800 rpm Motor power 0,25 kW Voltage 230 V length 350 mm width 210 mm height 305 mm Weight approx. 32 kg Scope of delivery - Diamond grinding wheel SBC - Collets ER 20, 3 - 12 mm, 10 pcs. (3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 mm) - Collets ER 40, 13 - 32 mm, 20 pcs (13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 / 23 / 24 / 25 / 26 / 27 / 28 / 29 / 30 / 31 / 32 mm) - Collet holder ER 20 resp. ER 40 Features - Including device for pointing, i.e. better centering of the drill tip on the workpiece and reduction of the necessary feed force - 30 pcs. ER collets included in the scope of delivery, which are also suitable for clamping intermediate sizes - Additional station for relief grinding of the drill cutting edges (clearance angle) - Universally adjustable point angle from 90° - 135 - Rotor with precision ball bearing ensures very smooth operation Iajdpfsgd H U Ujx Aqueu - Fast and precise working results due to simple operation - Vibration-free running due to high dead weight and rubber feet