Press Brake

AMADA PROMECAM ITS2 8025

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication Fjdsx Tgr Tepfx Ak Uepl DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1993, Technical details: sheet width: 3050 mm plate thickness: 6,0 mm distance between columns: 3460 mm no. of strokes: min./max.: 9 / 17 Hub/min back gauge: 750 mm (motorisch) mm cutting angle: 0,5° - 3,0° ° cutting gap adjustment: manuell mm down holder: 18 Stück (hydraulisch) Stück Table dimensions: 380 x 3100 mm total connected load: 7,5 kW weight of the machine ca.: 4,56 t dimensions of machine: L: 3,64 x B: 2,55 x H: 1,58 m Fsdsu Rni Hjpfx Ak Ujpl Equipment: With side stop L: 1000 × W: 100 × H: 60 mm and stop bar 990 mm, with 8 supports Operation via control panel and foot switch Cutting zone lighting Stroke counter Machine feet *

Year of construction: 2024, condition: new, Motorized sheet metal shear Technical data Cutting capacity: 2.5 mm Cutting length: 2550 mm Cutting angle: 1°40′ Fpsdohk Nf Rjpfx Ak Uol Stroke rate/min: 35 1/sec Motor power: 3 kW Back gauge range: 550 mm Table width: 400 mm Table height: 850 mm Height: 1260 mm Width: 1350 mm Length: 3100 mm Weight approx.: 1540 kg

Condition: ready for operation (used), Year of construction: 2003, sheet width 2520 mm plate thickness 2.50 mm ST thickness at "Niro-steel" 1.50 mm upper clamping bar adjustment 160 mm adjustment speed 100 mm/sec Adjustment folding beam 80.0 mm Bending speed ca. 120 Grad/sec compressed air 6.0 bar work height max. 869 mm control POS 2000 total power requirement 7.2 kW voltage 400 V weight 3430 kg Current new price ~ 100.000 euros From a maintenance workshop With very good equipment (!!) Equipment: - CNC electric motor-driven universal swivel bending machine * High-precision mechanics with modern control technology * For individual and series production * Robust high-speed machine with high axis speeds * Torsion-free welded construction - Rotatable upper beam / as automatic tool change system * With 2x tool stations (sharp and goose foot bending rail) * Reduces set-up and idle times * Eliminates time-consuming tool changes and adjustments Fpedpfxoxbh Eus Ak Usl - SCHRÖDER CNC control model POS 2000 * Control panel at front right (operable with PC mouse) * Color display * USB interface * Automatic cutting calculation * Material and tool library * Dimensionally accurate bending simulation * Windows XP operating system * Swivel control, front right - Servo converter-controlled drives * for bending/upper beam & electric backgauge - CNC motorized lower beam adjustment - CNC electric motorized backgauge * Travel speed 300 mm/sec. - with rear sheet metal support surface, including ball rollers - 1x freely movable double foot switch - Operating instructions (PDF)

Condition: like new (used), Year of construction: 2024, Overhauled: 2024 Year of manufacture: 1994-2000 Saw blade 560 mm Motor power 6,5 / 8,0 KW Speed 1500/3000 min-1 Cutting speed 2100 - 4200 m/min Saw height control: electronic Working range square max.: 170x170 mm Working range flat max.: 300x150 mm Working range round max.: 200 mm Saw feed 0 - 40 mm/s infinitely adjustable Cutting length 5-950 mm (9999 mm multiple stroke) Feed speed max. 500 mm/s Weight approx. 1900 kg Dimensions LxWxH 2200mm x2700mm x1950mm The machine is in mint condition, both technically and visually, following a completed retrofit. Due to its equipment and design, the machine can be used very efficiently for a wide range of applications. The programmed HMI control system ensures simple and very profitable operation of the machine. The soundproof cabin reduces noise emissions to a minimum. The machine is generally overhauled in our company at the customer's request. Among other things the following points will be renewed: - Conversion to Siemens S7 PLC control - Conversion to Siemens HMI user interface - Replacement of the ball screw - Replacement of servo motor and servo inverter - New electrical components - New pneumatic lines - New pneumatic components - Overhaul or replacement of all pneumatic cylinders - Renewal of the valve terminal - Optimization of extraction performance - Overhaul of minimum lubrication system - Replacement of general wear parts Fjdpfxsuiy Hre Ak Ujpl - Overhaul of the cab The machine also has: - Soundproof cabin - Splitting extension (for a high-quality cutting surface without return marks) - Height control fully electronic Warranty: Unless otherwise agreed, we provide a 6-month guarantee on all parts overhauled or replaced by us. Working time and wearing parts are excluded from the guarantee. Optional: - Mass clamping device for parallel sawing of several workpieces - Flat magazine for automatic feeding of up to 6 m long primary materials - Roller conveyors for primary material - Reinforced motor 18.0 KW (frequency-controlled) - Delivery and installation on your premises - Training of your employees

Year of construction: 1981, condition: good (used), machine/vehicle number: 3626, OFFER 21448 Technical data: - max. working width 2540 mm - max. cutting capacity St 40 4 mm - motorized cutting angle adjustment - cutting gap adjustment by means of graduated adjusting screws - number of hydraulic clamping bars 14 pcs - motorized rear stop with positioning 10 - 1000 mm - number of strokes depending on cutting angle and cutting length 23 per minute - hydraulic drive 400 V / 7.5 kW - table height 1030 mm - space requirement approx. W 2500 x H 1630 x D 2150 mm - weight approx. 3600 kg - including: - sheet metal lifting with pneumatic assistance - front angle stop + support arms - electronic cutting depth adjustment - cutting line illumination Fedpehhc Ixjfx Ak Uspl - electric foot switch

Condition: used, Year of construction: 2001, functionality: fully functional, Press force 85 t, Bending length 2050 mm, Distance between uprights 1750 mm, Control DELEM, Stroke 215 mm, Throat depth 410 mm, Total power 13 kW, Weight 8,750 kg, Machine dimensions 3190 x 2100 x 2375 mm Fpsdpfow Imq Rjx Ak Uol

Condition: ready for operation (used), Year of construction: 2012, A Mitutoyo coordinate measuring machine overhauled in 2023 is available. Measuring dimensions X/Y/Z: 705mm/1005mm/605mm, max. workpiece height: 800mm, table dimensions X/Y: 880mm/1720mm, max. table load: 1000kg, resolution: 0.1µm, traverse speed: 520mm/s, measuring speed: 8mm/s. Machine dimensions X/Y/Z: approx. 1500mm/2000mm/2750mm, weight: approx. 2000kg, control: GEOPAK and CAT 1000 PS. Including various probe trees. Documentation available. On-site inspection is possible. Fedpsx Ih A Njfx Ak Ujpl

Condition: used, Year of construction: 2014, total length: 1,500 mm, total width: 1,150 mm, total height: 2,400 mm, Weight: 3.600 kg - Year: 2014 - Documentation available: Yes Fsdpfx Akexapftj Ujpl - CE marking present: Yes - CE certificate present: No - Serial number: 441 - Power [kW]: 3.0 - Press force [ton]: 28 - Max. working width [mm]: 1000 - Column gap [mm]: 950 - Throat depth [mm]: 220 - Backgauge depth [mm]: 415 - Transport dimensions: 1500mm x 1150mm x 2400mm (l x w x h) - Transport weight [kg]: 3600kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: ready for operation (used), Year of construction: 2018, operating hours: 18,845 h, spindle speed (max.): 4,000 rpm, travel distance X-axis: 260 mm, travel distance Y-axis: 53 mm, travel distance Z-axis: 830 mm, spindle motor power: 33,000 W, controller manufacturer: SIEMENS, controller model: 828D, number of axes: 3, This 3-axis DOOSAN Puma 2600 SY II was manufactured in 2018, designed for precision in horizontal turning. Ideal for complex machining tasks, this machine ensures robust performance and durability. If you are looking to get high quality turning capabilities consider the DOOSAN Puma 2600 SY II machine we have for sale. Contact us for more information. Fodpjyr R A Ejfx Ak Ujpl Additional equipment • Mekiload Gantry Loader • Renishaw Equator • Renishaw Equator • Machine includes a rotary indexing magazine • Machine includes a gantry robot Machine Benefits Qualitative Machine Benefits • Tool change time: 1. 0 second • Max speed (station): 5000 rpm • Holder for turning tools: 25 x 25 mm • Holder for boring bar: Ø50 mm • Coolant pump capacity: 1. 5 kw Technical Machine Benefits • Max. Turning diameter over bed: 780 mm • Max. Turning diameter over slide: 630 mm • Max. Turning length: 760 mm • Main spindle torque: 719 nm • Spindle mount (main): a2 #8 • Sub spindle speed: 6000 rpm • Sub spindle power (30 min): 18. 2 kw • Sub spindle torque: 220 nm • Spindle mount (sub): a2 #5 • Number of stations: 24 (12 driven) Extra Information Machine still under power