Complete sawline for big logs

AKE,Söderhamns, Remill, Catech, Ari

Condition: good (used), Year of construction: 2019, CNC through-feed center with dual clamp drive in X-direction and gantry design in Y-direction. The second gripper enables trimming down to 15 mm as well as continuous milling movement along the X-axis. The workpiece length is measured (X-direction) via sensor measurement. Working area: X-axis: 3,500 mm Y-axis: 950 mm Z-axis: 80 mm Milling spindle 12 kW HSK-F63, up to 24,000 rpm max. 4-position linear tool changer for milling tools. Max. tool diameter: 120 mm Max. tool length: 100 mm Single pick-up station for ergonomic insertion or removal of tools into the machine. Additionally usable as extra tool positions for up to 11 virtual tools. Automatic length measuring system for tools in Z-direction. Drilling head DH 25 8H 1S - 17 vertical spindles - 8 horizontal spindles - Grooving saw in X-direction Dowel insertion unit with 2 tools Dowel diameter: 8 mm, lengths: 20-25-30-35 or 40 mm Air cushion tables at front and rear, foldable Machine software WOODFLASH with: - CNC Board (general machine operation) Lredpfxexrahcj Afask - Tool database (Tecno-Manager) - Programming editor External workstation license Dongle upgrade: 3D simulator with collision check for WOODFLASH at the machine Release of workpiece at the rear side of the machine Machine is supplied without tools and HSK holders

Condition: excellent (used), Storti RM 500 edger - Italian production Ljdpfx Afek Talpsaork - year of production 1993 - electric spacing of discs TECHNICAL PARAMETERS: - cutting width max 435 mm - cutting height max 170 mm - engine power 2 x 22kW - max element width 600 mm - minimum material length 800 mm - max disc diameter 600 mm - spindle diameter 40 mm - two upper pulling rollers - one upper pressure roller - roller motor power 2 x 1.1 kW - roller pressure with automatic jump - seven bottom pulling toothed rollers - electric disc adjustment - two lasers - feed speed 25 and 50 m/min - feeding table 2950 mm - receiving table 3000 mm - drive rollers D100 mm - power of the roller feed motor 2 x 1.5 kW Transport dimensions 500x240x180 cm weight 3500 kg

Condition: ready for operation (used), Year of construction: 2023, number of axes: 9, This 9-axis NAKAMURA-TOME WY150 was manufactured in 2023, featuring a turn-mill centre with a comprehensive toolholder setup including 6 external, 4 internal, 3 radial rotating, and 12 axial rotating holders, plus a collet chuck and a 3-jaw chuck. Consider the opportunity to buy this NAKAMURA-TOME WY150 turn-mill centre. Contact us for more information. Additional equipment • 6 external toolholders • 4 internal toolholders • 3 radial rotating (driven) toolholders • 12 axial rotating (driven) toolholders • 1 collet chuck • 1 three-jaw chuck Lrodpfx Aoyb Sakefaek

Condition: new, Year of construction: 2025, HIGH-PERFORMANCE WRAVOR BANDSAW, SPECIALLY DESIGNED FOR PRECISE AND EFFICIENT CUTTING OF LAMINATED BEAMS. IT ENSURES HIGH-QUALITY CUTS, MINIMAL MATERIAL LOSS, AND OPTIMAL PRODUCTIVITY. Lsdpovu Um Njfx Afajrk 📌 Key features: ✔ Precise cutting of laminated beams ✔ Automatic control for increased efficiency ✔ Robust and reliable construction

Condition: refurbished (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 12786 040, overall weight: 20,000 kg, rotor diameter: 640 mm, total length: 4,900 mm, total height: 2,600 mm, total width: 4,100 mm, rotor width: 2,000 mm, power: 203 kW (276.00 HP), rotational speed (max.): 340 rpm, input current: 415 A, Equipment: rotational speed infinitely variable, The Vecoplan VAZ 2000 M F-T is a powerful single-shaft shredder. This robust shredder offers an efficient and reliable solution for a wide range of applications. Possible applications: - Household waste - plastics - paper With its proven technology and high throughput of 4-5 tons per hour, the VAZ 2000 M F-T is the perfect choice for shredding and volume reduction in disposal and recycling processes. Lrodpfx Aourkc Refajk The pictures are examples. The pictures do not show the machine as it is offered, they only serve as an example of what the machine will look like after the overhaul. Price on request.

Condition: new, Ostas 3-roller round bending machine SBM 1270 x 95 Special equipment included in the price: Hardened rollers Motorized rear roller adjustment Digital display Features: - Asymmetrical 3-roller round bending machine with motorized drive - Hardened rolls - Motorized rear roll adjustment - Digital display Lsdpog Tzbhsfx Afaerk - Upper roll can be swung out - Conical bending device - foot switch Technical details: - sheet width: 1270 mm - sheet thickness: 3,0 mm - roll length: 1270 mm - Roll diameter: 95,0 mm - Smallest bending diameter: 140,0 mm - Motor power: 1,1 kW - Dimension L-B-H: 2100 x 760 x 1250 mm - weight: 470 kg

Condition: used, Year of construction: 1989, functionality: fully functional, Used dip installation, manufacturer Bachhäubl HS2 12.5 - 12.50 m long x 1.50 m wide x 1.50 m high, clear internal dimensions; - Year of manufacture: 1989; - Control unit with timer relay for setting immersion time. - Wooden support with frame approx. 7 m long, hold-down device with 7 prongs, approx. 7 m long; - Basin interior in good condition, Lredjx Aktwspfx Afaek - single-walled, without collection tray! - Weight approx. 8.5 tons - Transport dimensions approx. 13.00 x 2.35 x 2.80 m - Installation is supplied without impregnation agent and without sludge, - free loaded on truck!

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Ljdpfx Afewp Rqfsaerk Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Year of construction: 2011, condition: used, functionality: fully functional, Finger jointing line for cross sections up to 200 cm² (80/240 mm or 100/200 mm), with the following. components: 1. HOWIAL tilt unstacking - SH/4t - 1,75x1,75x6,00m - 4t - short. Length 2,50 m, semi-automatic separation of the package. For tilting the wood pile up to 45°. Electric motor drive. stack dim. max. 1,75 x 1,75 x 6,00 m max. stacking load 4 t shortest wood length 2,5 m 2. HOWIAL - VE 1 lamella separator for crosscut saw. With pneum. controlled tongues, on which the material is marked for defects, deposited on the roller conveyor below. 3. HOWIAL - evaluation roller conveyor RO-1 digital wood moisture measuring, control and recording system for autom. recording and control of wood moisture in cycle measuring method according to electric resistance principle. 4. gann DMT-8 dig. Wood moisture measuring, control and recording system for automatic detection and control of wood moisture in the cycle measuring method according to the electrical resistance principle. Plant in large switchboard complete with ink jet printer. 5. HOWIAL - crosscut saw AS-30 B pneum. Under table crosscut, with 2 autom. feed units, autom. crosscut. Special photocell control for detection of fluorescent line markings. Automatic waste disposal possible. Saw motor power 7,5 kW saw blade diameter 700 mm feed drive approx. 2 x 1,5 kW Air pressure 8 bar feed speed max. approx. 60 m/min. 6. HOWIAL - conveyor belt cut off waste, with studded belt and guide plates belt width 350 mm belt 2000 mm long belt speed 0,4 m/sec. 7. HOWIAL - double roller conveyor RO-2 6,00 m long incl. transversal transport, drive by round belt, all rollers driven. Cross transport chain conveyor. Ejection ± moisture right Transport speed adjustable 100 m/min. length approx. 6,00 m Width of rollers approx. 400 mm Lrodpfxji Ezx Dj Afajk Diameter 112 mm 8. compact finger jointing machine Cook Bolinder The technical data are original from Cook Bolinder: wood width from 75 to 245 mm Timber thickness from 20 to 105 mm Input lengths from 1m to 6 m Cross sections from 30 cm² to 200 cm² Pressing force 5 - 22 to Spindle diameter 50 mm tine profile 15/15 spindle speed approx. 6000 upm Total electrical connected load approx. 62 kW Machine weight approx. 9 to. Gluing OEST comb system for PU Modern Telemechanique SPS control. 9. HOWIAL - Roller conveyor with destacking system Driven roller conveyor with autom. ejector and hydr. driven destacking arms. Technical data: H: 920 mm L: approx. 12.000 mm 10. safety fences incl. circuit breaker 11. finger joint testing machine BSPLT-100 Testing machine for finger joint bending test according to DIN 1052-1/A1 and EN 385 Support distances freely adjustable, attached dimension scale, autom. calculation of support distances in the software. Fully automatic test procedure by mouse click on PC (not included). Alternatively, the test procedure can be started by key operation on the front panel. Connection of any commercially available PC or laptop (Win 2000/XP) via the supplied RS232 serial cable. Fully automatic measured value logging as well as automatic logging in MS-Excel with graphical display. Representation max. wood width: 300 mm max. wood thickness: 140 mm max. compression force: < 100 kN max. support length: 2100 mm Measuring accuracy WITHOUT DISMANTLING

Condition: refurbished (used), Completely refurbished Bongioanni CRL 4 tensioning wagon with clamping blocks. Track gauge 1200 mm. Rails newly milled. Servo-electric drive. Sale upon customer order. Lrsdpfx Asxtwxbjfask