Wire EDM machine

AGIE Classic V3

Condition: used, Year of construction: 2004, x-travel 650 mm y-travel 600 mm z-travel 500 mm control Sinumerik 840 D pl Siemens turning speed range - main spindle 20 - 28.000 min/-1 power capacity - main spindel 23 / 18 kW max. Torque 79 Nm tool taper HSK-A63 table surface area Ø 630 mm Swivel range A: +30° / -115 ° rotatable C: 360 ° max. table load 500 kg max. workpiece sizes Ø 630 x 313 mm table speed A:25 / C:65 min/-1 number of toolpositions 117 pos. max. tool diameter 90 (125) mm max. tool length 300 mm rapid traverse ( X / Y / Z ) 60 m/min Accelaration 10 m/s² feed power 8,5 kN total power requirement 43 kVA weight of the machine ca. 10,5 t dimensions of the machine ca. 6,5 x 4,5 x 3,0 m 5 Axis CNC - Machining Center Universal HERMLE - C 30 U Dynamic - Tool-Magazine 117 pos. - ca. 9.000h Spindle-hrs. after change Dedpfxjzd E Tbo Ab Tokp - OPTIONALLY available with a pallet changer (extra cost)

Condition: new, Year of construction: 2026, grinding length: 700 mm, grinding width: 400 mm, COSMOS E 7040 NC Precision Surface Grinding Machine, grinding area 700 x 400 x 350 mm, spindle power 3.7 kW, grinding wheel 300 x 50 x 76.2 mm, Mitsubishi PLC control and drive technology, very user-friendly, incl. magnetic chuck 700 x 400 mm with adjustable holding force, grinding spindle with speed regulation, automatic grinding cycle with rough grinding, fine grinding, spark-out and retraction, dressing with size compensation, coolant system with paper band filter. 12 months warranty. Inspection under power and test grinding possible at any time. We are happy to provide on-site installation and training as well as subsequent service! Financing / leasing available upon request – we will gladly provide an offer! Dsdpfsrwwt Sex Ab Tjkp

Condition: good (used), Year of construction: 1998, Max. Pitch circle diameter External gearing 300 mm Max. Pitch circle diameter internal gearing 300 mm Max. Outer diameter of workpiece (equipment) 450 mm Dkedpfx Aevu E Nuob Tsp max. module 6 gear hobbing width -max. 100 mm Max. Helix angle (with tool Ø 125 mm) +/- 45 ° strokes - infinitely variable 130 - 1300 Hub/min workpiece weight 1000 kg Minimum distance table top - tool spindle -55 / +300 mm Maximum distance table top - tool spindle 200 mm Maximum distance table top - tool spindle 350 mm Manual Upright side shift +/- 25 mm Manual swivelling angle of the tool spindle +/- 0,5 ° Max. Tool speed 15 UpM Max. Workpiece speed 27 UpM Max. Tool diameter 7 Zoll voltage 400 V frequency 50 Hz Max. Line power 70 A total power requirement 48 kW weight of the machine ca. 11 t dimensions of the machine ca. 4,27 x 3,11 x 2,87 m taper in main spindle SK 45 table hole 40 mm control Siemens Sinumerik 840 C Gleason PFAUTER gear shaping machine Mod. PSA 300 The CNC modular gear shaping machine with skiving cutter for the machining of external and internal cylindrical gears, with straight or helical involute with straight or helical involute toothing, as well as any other profile splitting process. The work cycle is controlled by a CNC unit, with specific software for machining the gears, machining. Field of application --> The PSA 300 has been designed for the production of: - Gears with straight external teeth - Gears with straight internal teeth - Gears with external helical teeth - Gears with internal helical teeth

Condition: used, Year of construction: 2001, Technical details: x-travel: 2500 mm y-travel: 1000 mm z-travel: 750 mm table surface area: 3220 x 1000 mm Workpiece weight approx.: 3000 kg spindle taper ISO: 50 milling spindle turning speeds: 20 - 5000 U/min feed speeds: 1- 30000 mm/min rapid traverse: 30 m/min total power requirement: 40 kW dimensions of the machine ca.: 6,9 x 4,1 x 3,7 m weight of the machine ca.: 21 t with CNC HEIDENHAIN TNC 426 30-pockets autom. toolchanger RENISHAW measuring probe coolant attachment with TSC and chip conveyor diverse toolholders * Dkodpfx Absvptmwj Tsp

Condition: excellent (used), Year of construction: 1995, Combination Unit: Manufacturer: GSG Feeder: Type: 840.02-027 Crusher Descaler: Type: 663.02-017 Wire Range: Ø5.5-16mm For wire rod with approx. 40-60 daN/mm² strength Crushing and Bending Rollers: Carbide Inserts Adjustment with 0.37 kW - 1.15 A gear motor Brush Drive with 0.25 kW gear motor, n=293 rpm Connection Voltage: 380-420 V 50 Hz Dry Coating Unit: Type: BSG/T Filling: Calcium Stearate (e.g., Traxit Type: D S 51 E) Stearate Consumption: approx. 350 g per t of wire Drawing Speed: max. 15 m/s Electrical Power: 2x 0.55 kW gear motors Cassette: 2 slots (supplied with 1x roller block + 1x cassette) Type: PKG/T (TS) Cleaned rolled wire Wire strength approx. 40–60 daN/mm² Wire range max. inlet diameter 9.5mm, finished diameter 3.5–8.5mm Roll dimensions min. Ø115mm, max. Ø125mm, Bore diameter Ø82mm, width 15–25mm Cooling pin diameter 25mm Cooling water consumption approx. 600 l/h Drawing machine: Manufacturer: Koch Type: KHZ 5000 Year of manufacture: 1993 Serial number: 13.821 Number of draws: 1 draw per block Drawing drum: Ø700mm Tensile force: mechanical 5000 N Wire material: mild steel wires Run-in strength: approx. 40 – 45 daN/mm² Maximum drawing range: Inlet diameter 5.0 – 8.5mm Cross-section reduction: 20 x 25% (mechanical gradation) Drawing speed: up to max. 7.0 m/s Brake: Twiflex, type: MRB Drive: AC motor/frequency converter, Siemens PN=110 kW, n=1485 rpm Spooler: Manufacturer: Koch Type: KHS 1250 Year of manufacture: 1993 Factory No.: 13741 Wire diameter: 5 – 8.5 mm Strength: approx. 55 – 70 daN/mm² Winding speed: V=7 m/s, adapted to the drawing machine Filling weight: approx. 3000 kg Spool drive motor: Three-phase motor with external fan Dodor Nfvmepfx Ab Tokp Type: 1 PQ 6253 – 6 AA 70- Z A 15 + K 20 + C 14 + H 46 P=37 kW, n=1000-2000 rpm, IP54, design B3 Laying drive motor: 66-671U, 1.5 kW, 170 V, 9.8 A, 1680 rpm, IP 44, B5-200 With Attached tachometer generator TG 20, 20 V / 1000 rpm With attached spur gear SK 32, i=57.53, design B6 Hydraulics: Hydraulic excavator type: H13 AK Pneumatics: Twiflex disc brake type: MRB Pneumatic cylinder type: SPWG 28032-25mm stroke Dimensions: 3100 x 3000 x 1700 mm (L x W x H) without counterweight

Year of construction: 2017, condition: ready for operation (used), - USED - FIBER LASER CUTTING MACHINE FOR TUBES WITH LOADING/UNLOADING SYSTEM MIN CIRCULAR SECTION: ø 25 mm MAX CIRCULAR SECTION: ø 355 mm MAX SQUARE SECTION: 260 X 260 mm MAX RECTANGULAR SECTION: 300 X 200 mm Dkodex E Eihspfx Ab Top MAX ADMITTED LOAD: 100 Kg/m SOURCE: IPG YLS-4000 ; 4000 W CONTROL UNIT: SIEMENS 840D WEIGHT: 12500 Kg NOTE: AUTOMATIC LOADING 3-12.5 mt; AUTOMATIC UNLOADING 12.5 mt; 3D CUTTING HEAD; CAPACITIVE SENSOR; AUTOMATIC ADJUSTMENT

Condition: used, Year of construction: 2017, CNC gantry plasma cutting machine (beveling unit) Dodpfxsw Rpvbj Ab Tokp Manufacturer: Zinser Type: 2425-I/3600 Year of manufacture: 2017 CNC control: 5010 Travel length: 11 m Oxy-fuel cutting table with oscillating conveyor system, including dust extraction system Dimensions: 2,000 x 8,000 mm 1 plasma torch with Hypertherm XPR300 power source automatic gas console including automatically rotating plasma beveling unit Bevel System 2015/350 Downflow filter system 3DFP9-SP Power: 9 kW Laser diode 3726

Condition: new, functionality: fully functional, Year of construction: 2025, laser type: fiber laser, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, Cutting format (mm): 12000*2500 X-axis travel (mm): 2530 Y-axis travel (mm): 12050 Z-axis travel (mm): 120 Maximum synthetic positioning speed (m/min): 140 Acceleration (G): 1.5 Dksdpfx Ajwwz Dxjb Tsp Main unit volume (mm): 15600*3650*1900 Floor area (mm): 16000*5500 Total machine weight (KG): 12500

Year of construction: 2007, condition: used, gear hobbing diameter - external 1200 mm gear hobbing diameter - internal 1200 mm gear hobbing width -max. 260 mm control Liebherr PC-NC max. workpiece diameter 1500 mm Dkjdpfxew Rf S Ej Ab Tjp table diameter 900 mm table bore diameter 320 mm max. table load 95 kN power capacity 30 kW coolant pump 120 l/min Axial distance between thrust spindle - table 0-820 mm Shaping spindle diameter 125 mm tool taper SK 45 DIN weight of the machine ca. 26 t dimensions of the machine ca. 8,073 x 6,183 x 4,375 m Strokes: - Stroke length min./max. - 0 mm / 270 mm - Stroke length adjustability - 270 mm - Stroke rate (double strokes) - 10 to 270 DH/min Equipment/accessories: - Chip conveyor - Cutting wheel holder SK 45 DIN - Cooler - Technical documentation

Condition: excellent (used), Year of construction: 2019, MAZAK QUICK TURN 350MB 1250U Max. swing diameter: 830 mm Max. turning diameter: 420 mm Max. turning length: 1,250 mm Max. milling speed: 5,000 rpm Max. spindle speed: 3,300 rpm Dsdpfx Abjy Igz Ds Tekp Machine is equipped with: - CNC control Mazatrol SmoothG - SMW three-jaw chuck KNCS 400, diameter 400 mm - Tool Eye - C-axis - NC tailstock - Reinforced coolant pump - Chip conveyor - 8 pcs. fixed tool holders - 2 pcs. driven tool holders