Circular Shear

WMW KS 1000

Year of construction: 1980, condition: good (used), Offer 22501 Technical data approx: - max. working width 1020 mm - max. material thickness at 40 kg/mm² strength 1,5 mm - man. backgauge adjustable up to 550 mm - front angle stop - sheet holding-down device - table size 1100 x 650 mm - working height 900 mm - space requirement approx. W 1800 x H 1450 x D 850 mm - weight approx. 400 kg - mobile Nodpfx Acskzik Heboct

Condition: new, Year of construction: 2024, machine/vehicle number: 302340, Profile Bending machine KB Türkei model MB 30 bottom shaft 30 mm top shaft 35 mm two rollers driven with basement capacity: up to round tube 48 x 3,0 mm flat material 50x10 mm Ncjdpfsd S Uf Sjx Acbot square tube 40x40x3,0 mm weight 170 kg motor 0,75 kw 400 Volt 50 Hz 3 ph.

Condition: new, carrying capacity 500 kg number of suction cups 6 suction cup dia. 215 mm Vacuum lifter VH 6-500 for the horizontal transport of smooth, dry and airtight panels. Robust supporting structure made of steel, painted in RAL 2000 with low Own weight. consisting of: - 1x galvanized longitudinal beam with a length of 2,400 mm - 3x galvanized crossbeams with a length of 1,000 mm - 6x Springy, articulating and adjustable suction cup holders - 6x suction cups Ø 215 mm, the seal can be separated in case of wear whose metal supports can be changed inexpensively and without tools - 6x ball valves to switch off individual suction cups, thus also smaller formats can be lifted without having to move suction cups or traverses. - 1x spiral connection cable small helix: * with an extension length of 3,500 mm, designed as an extension cable with CEE plug and coupling. * is routed to the lifting device next to the load chain. - Low-maintenance, very high-quality, dry-running rotary vane vacuum pump a suction capacity of 8 m³/h and a final vacuum of 85% (150 mbar) - Electrical connection: 3 phases 230/400 V + PE, 50 Hz, with cable (approx. 0.5 m long) and CEE plug (16 A). Integrated into the control with isolating transformer (necessary if the vacuum lifter is connected via the crane trolley and this has no neutral conductor) - Operating handle can be extended to 1,000 mm from the center of the traverse. Sturdy sheet metal bag for your crane control incl. at no extra charge. - Operation "suction / release" using manual slide valve: The wear-free and very robust manual slide valve ensures safe Suction and release after pressing the release button. (twice loosening according to EN 13155) - Control and safety device for vacuum lifters: * Robust control box. * Contactor circuit for the vacuum pump. * Safety warning device with audible alarm. * Vacuum gauge with danger zone indicator. * Large vacuum storage tank with safety check valve * Double actuation when releasing the load. - Fine dust filter to protect the vacuum pump Nedpfxsq Sc Aus Acbjct - Detailed and easy to understand documentation. One year warranty against material and manufacturing defects One-shift operation (without wearing parts). Initial test UVV 18, VBG 9a with CE declaration of conformity - according to EN 13155 - Packing for truck transport.

Condition: new, Year of construction: 2025, Automatic snap lock roof panel machine Sl-1 auto is designed by our company for the self-locking roof panels production in automatic mode. This machine forms a roof lock by rolling with the help of special rolling rolls. At the same time while rolling it cuts fastening holes for roof panel’s fixation. Automatic snap lock roof panel machine SL-1 auto consist of: - Roll forming part, which directly forms the desired profile of the panel with the help of rolling rollers. The machine is equipped with width easy adjustable system - to change the width; you just need to turn a special adjustment wheel. The rolling machine has 10 pairs of forming rolls to form a click-seam lock. It has special tool to cut fastening holes in panels. Nodpjn Hqmmofx Acboct - Automatization system of machine, with the main elements as follows: automatic control panel, manual control panel, control cabinet, measuring wheel. With the help of this system, machine operator can program it to perform metal rolling and cutting operations in automatic mode. It is easy to set the number of panels for rolling and their lengths, so you just need to feed metal into machine, and it will roll panels of click-seam of the desired length and quantity in automatic mode. It is possible to perform several tasks (multi-tasking). If use manual control panel you can check each operation step of the automatic mode before put it to full automatic process. - Guillotine shear, designed for cutting click panels of various widths. The special configuration of blades makes it possible to cut such profile and to get high quality final product. Shear system has electric motor to make cutting operations easy. As an additional equipment for the machine, we offer: - metal uncoiler for convenient installation of roll metal and feeding it into the machine. - full automatic decoiler to make roll forming process maximum automatic. - ribbed panel rolls, to form additional ribs to the click-fold panels, so it gets more interesting look to the roof and increasing the rigidity of the system. - ribbed panel forming machine RPFM (microwave panels machine) to form microwaves on roofing panels. Due to its low weight, the automatic roll forming machine for self-locking panels SL-1 auto can be used in the construction of civil and industrial facilities, in factory workshops and workshops, as well as directly on the roofing site. Using of machine close to the place of installation avoids transportation costs and the associated risk of damage to the roofing sheets. The high of snap lock roof panel profile when installed is 26mm: As an option, we can also make machine for 31mm lock high production: The maximum workpiece width for rolling can be 700mm. The minimum workpiece width is 250mm. Automatic snap lock roof panel machine Sl-1 auto has special protective cover that prevents foreign objects from getting to working part of machine. So snap lock automatic roll forming machine SL-1 auto is convenient to use with the help of automatic mode so you can minimize operator’s work and to get high-quality roofing panels with high productivity.

Year of construction: 2009, condition: ready for operation (used), machine/vehicle number: 527, Offer 23035 Technical data approx: - Pressure capacity 30 T. - max. sheet thickness 10 mm - max. punching diameter 105 mm - punching capacity - e.g. steel sheet : 105 mm in 1,5 mm ; 45 mm in 5 mm - e.g. VA - sheet metal : 90 mm in 1,5 mm ; 45 mm in 4 mm - stroke 7 - 70 mm Nedolnkc Uepfx Acboct - throat 560 mm - maximum stroke rate 120 H/min - single stroke / continuous stroke - drive 400 V / 4 kW - space requirement approx. W 8000 x H 1850 x D 1700 mm - weight approx. 1900 kg - with: - stop table with stops - foot switch; - emergency stop button - punch quick change device - various receptacles for punches and dies

Year of construction: 1987, condition: used, sheet width 150 mm coil weight 80 kg coil external diameter 650 mm 1000 mm Ncedpfx Aofn Aqlocbjt diameter of the mandrel 230 - 445 mm total power requirement kW weight of the machine ca. t dimensions of the machine ca. m

Condition: new, Year of construction: 2025, Roll forming metal siding “double façade panel” machine SPM-2 Roll forming metal siding “double façade panel” machine SPM-2 is new design product of our company for façade and wall metal panels forming with the necessary configuration. These double façade panels are very popular in construction business of cladding residential buildings and industrial structures, for the construction of fences of various configurations, gazebos, roofing elements, etc. Ncodpoxghngjfx Acbot The SPM-2 metal siding production line is fully automatic and consists of a rolling part of the machine, an automation system and guillotine cutting shears at the machine exit. The line can have as additional parts a manual or automatic uncoiler for metal rolls, depending on the customer's needs. As standard version, this metal siding double façade panels roll forming machine SPM-2 makes a flat panel profile, but with the additional equipment, it is possible to roll panels with a microwave or rib shape profile. To start rolling, it is necessary to install a roll of metal to the decoiler and to put the end of the strip to the first rolling rollers of the equipment and feed it into them. After step by step, to put the metal to the next rollers, adjusting it if necessary. When metal comes to the cutting device of machine you need to feed metal into cutting knives and to make “zero” cut. After such step, equipment can move to automatic operation mode. The control panel of machine has the ability to set the number of tasks and the length of products, single tasks or to work in multitasking mode. After setting up necessary parameters the machine will automatically roll the metal cladding wall panels and cut them into necessary sizes. Thus, the customer will receive final product as quickly as possible and with the highest possible result. The roll forming speed is adjustable and can be up to 10-15 meters per minute. The SPM-2 metal wall cladding panels production line has special tools for punching out fastening holes on the side of the panel. It makes possible for the customer to get more interesting solution options and to offer a wider range of products to the end user. The rolling part of the machine has 18 pairs of forming steps, ensuring high quality of final product. You can get machine with protective cover or without it as per your request preferences. Specifications Material width (mm) 416 The material thickness (mm) 0,4-0,5 Engine power (kW) 3 + 1,1 Rolling speed (m/min) 10-15

Condition: used, Year of construction: 2010, functionality: fully functional, sheet thickness steel (max.): 1 mm, number of blades: 5, working width: 1,250 mm, number of feed rollers: 2, FORSTNER MST 1250 Longitudinal Slitting and Sheet Cutting Machine The machine is in very good condition and fully operational. Designed for longitudinal slitting and cutting into sheets. It is currently connected - can be tested on site. Longitudinal slitting into 6 strips (5 pairs of knives), with the option to mount up to 7 pairs. Control – Siemens SIMATIC touchscreen panel. Full documentation (PDF) included. Specifications: Model: FORSTNER MST 1250 Made in: Austria Year: 2010 Working width: 1250 mm Nodpex R Sk Nofx Acbsct Thickness: up to 1.0 mm Slitting knives: 5 pairs Shearing: circular shears Controller: Siemens SIMATIC panel If you have any further questions, we will be happy to answer.

Condition: ready for operation (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 1, overall weight: 4 kg, Downspout Pipe Production Line Strip thickness: 0.6 - 0.7 mm Material quality: Steel and Pre-painted Product diameter: Ø 100 mm ( 75, 87, 111,120 mm optional dimention) Production Line included: Double Head Decoiler: 4+4 tons, Roll Forming Machine casstte type ( with extra cassettes ) Hydraulic Cutting Unit. Njdpswvhnhefx Acboct

Condition: new, Year of construction: 2026, The manufacture of modern folding machines is our passion, which we would like to share with you. At trade fairs, we share our experience and attention to our bending machines, thanks to which we can continue to improve our folding benches, so we don't forget who we really work for. The quality of our bending machines is very important to us. Bending machine ZGR-2140 / 1.2 Warranty: 12 months. Certificate CE Eccentric pressure that is shifted to both sides of the machine Working length: 2140mm STEEL SHEET 1.2 mm Non-ferrous metals 30% more sheet thickness Folding beam: 24 mm Bending angle: 145 degrees Cutting along the entire working length, Lifting the upper cheek in three positions, Ncedpfx Aceb Na Eqsbst maximum clear width between the side panels 80 mm rear frame for holding sheet metal, front cutter limiter to ensure the specified cutting width, We are looking forward to your contact!