Relieving lathe

WMW DH 250III x630

Condition: used, Technical details: turning length: 630 mm swing diameter over slide rest: Hinterdrehschlitten: 250 mm center height over bed: 270 mm centre distance: 900 mm spindle bore: 26 mm range of revolutions per minute - continous: 1,8 - 450 U/min return movement speed: 23 / 32 / 46 / 370 / 510 / 740 U/min cross feed: 0,07 - 1,11 / 36 step mm/U longitudinal feeds:: 0,063 - 0,63 / 12 step mm/U tailstock quill taper MT: 5 quill travel: 250 mm Csdjvbh N Rspfx Akcsrb Total power requirement: 7,0 kW machine weight approx.: 3,9 t dimension machine xH: 3,2 x 1,2 x 1,8 m Application: Mainly for relief turning and relief grinding of cutting tools (especially hobs with and without thread pitch). Back turning and relief grinding is possible from the front, the back and in the axial direction of the machine. Main drive via 8-stage manual gearbox. Feed gearbox is designed as a 12-stage manual gearbox. Swiveling range of the rear slide = 360deg. Swiveling range of the cross slide = 360degrees Equipment: lathe chuck driving disc Ø 210 mm with fixed tip fixed tip in tailstock with 4 pieces machine feet 3 jaw chuck Ø 250 mm i.D. *

Condition: used, Year of construction: 2009, greates pass round over bed 1050 mm dist. between centers 6000 mm centre height 520 mm turning length 4810 mm workpiece weight max. (main spindle) 6000 kg Maximum workpiece weight with steady rests 8000 kg max. torque on the spindle 12500 Nm number of spindle speeds 2,8-560 1/min feed per revolution 0,08-56 mm chuck diameter 630 mm Maximum travel distance of the longitudinal slide 4810 mm Crjdsygxy Uepfx Akcob Maximum travel distance of the cross slide (suppor 530 mm Maximum travel distance of the tool slide (support 340 mm Tailstock quill diameter 150 mm total power requirement 31 kVA weight of the machine ca. 10500 kg dimensions of the machine ca. 7860 x 1970 x 1480 mm Equipment/accessories: -2 x face plates -3 jaw chucks -2 x steady rests -Multifix holder -Turning tools -Various tips -Technical documentation

Year of construction: 1984, condition: used, machine/vehicle number: 25 948, throat: 485 bzw. 1050 mm roller-Ø: 500 mm passage height: 380 mm table size: Arbeitstisch 780 x 800 mm sawing band length: ueber 2 Laufraeder 3920 - 4050 mm sawing band width max.: 20 mm band speed: 15 - 940 m/min engine: 380 V, 4 kW space needed: 950 x 2130 x 2100 mm weight: 1740 kg Codpfx Akjb N Eh Hjcjrb

Condition: used, Year of construction: 1994, turning diameter 570 mm turning length 2000 mm control Sinumerik 805 Siemens swing diameter over face slide 365 mm main spindle speeds: 3-2.500 U/min Cjdpfeu Sbkgex Akcjrb drive of main spindle 15/19 kW spindle bore 62 mm spindle head DIN 55027 No.8 tailstock taper MT 5 quill stroke 190 mm pinole diameter 80 mm feed range - long. and cross 0,01-50 mm/u total power requirement 50 KVA weight of the machine ca. 5 t dimensions of the machine ca. m

Condition: good (used), Year of construction: 1956, Heavy lathe, turning machine, lathe, center and feed screw lathe, center and feed screw lathe -Manufacturer: Weisser, lead screw lathe type PF200 -Turning length: 1340 mm -Turning Ø over bed: 420 mm -Turning Ø over support: 240 mm -Spindle bore: Ø 41 mm -Spindle speeds: 31.5 - 1400 rpm -Three-jaw chuck: Röhm Ø 250 mm -Accessories: incl., see photos -Tailstock mount: MK4 Credpfetzf N Rox Akceb -Drive motor: 2.5/3.5 kW -Dimensions: 2670/1000/H1230 mm -Weight: 1450 kg

Condition: used, Year of construction: 1984, x-travel 2500 mm y-travel 750 mm z-travel 1000 mm Crjdpfx Astqqnwokcsb table surface area 2550 x 800 mm spindle taper SK 50 control HEIDENHAIN, TNC 150 B weight of the machine ca. 16 t

Condition: good (used), Year of construction: 1994, functionality: fully functional, feed length X-axis: 1,050 mm, feed length Y-axis: 360 mm, feed length Z-axis: 500 mm, travel distance X-axis: 1,050 mm, travel distance Y-axis: 360 mm, travel distance Z-axis: 500 mm, overall weight: 3,000 kg, Equipment: documentation/manual, Tiger FO 135 universal milling machine Description of the machine The machine was purchased new in 1994 and has only been in operation for a few hours. The milling machine is fully functional. The axis movements are smooth and the guides are in good condition. good condition. These have an automatic lubrication system. The table is in good condition and shows hardly any signs of wear. The machine also has a digital readout for the 3 axes, which makes it possible to work with cutter compensation and recurring measurement machining. Operating instructions are included with both the machine and the digital indicator. Technical specifications - Table dimensions 1,400 x 340 mm, 4 T-slots - Automatic traverse path: ➢ Longitudinal X 1,050 mm ➢ Transverse Y 360 mm ➢ Vertical Z 500 mm - Fixing the spindle cone: ➢ Vertical axis ISO 40, automatic locking ➢ Horizontal axis ISO 40, manual locking - Spindle speed range: ➢ Vertical axis 33 ÷ 1,560 rpm, 12 speeds ➢ Horizontal axis 35 ÷ 1,550 rpm, 12 speeds - Installed power: ➢ 5 kW vertical spindle motor ➢ 7.5 kW horizontal spindle motor ➢ Direct current motor 15 Nm - Variable power supplies Continuous speed 0 ÷ 1,500 mm/min - Fast feed ➢ Lengthwise and crosswise 3,000 mm/min Vertical 1,500 mm/min - Universal head with manual shaft lowering of 80 mm - Automatic lubrication with pump - Low-voltage electrical controls on the pushbutton panel of the side arm - Star/delta start - Magnetic thermal protection from Siemens - Net weight 3,000 kg - Machine dimensions (for transportation) ➢ Width 2,300 mm ➢ Depth 2,900 mm ➢ Height 2,400 mm Accessories - Counter supports for cutting shaft - Cutting shaft ø32 mm Tiger FO 135 universal milling machine Description The machine was purchased new in 1994 and has only had a few hours of operation. The milling machine is fully functional. Axis movements are smooth and the guides are in good condition. These have an automatic lubrication system. The table is in good condition and shows hardly any signs of wear. The machine also has a DRO for the 3 axes, which offers the possibility of working with milling compensation and recurring measurement processing. Both the machine and the DRO come with operating instructions. Technical specifications - Table dimensions 1,400 x 340 mm, 4 T-slots - Automatic travel: ➢ Longitudinal X 1,050 mm ➢ Transverse Y 360 mm ➢ Vertical Z 500 mm - Fixing the spindle cone: ➢ Vertical axis ISO 40, automatic locking ➢ Horizontal axis ISO 40, manual locking - Spindle speed range: ➢ Vertical axis 33 ÷ 1,560 rpm, 12 speeds Horizontal axis 35 ÷ 1,550 rpm, 12 speeds - Installed services: ➢ 5 kW vertical spindle motor ➢ 7.5 kW horizontal spindle motor ➢ DC motor 15 Nm - Variable power supplies Continuous speed 0 ÷ 1,500 mm/min - Fast forward ➢ Longitudinal and transverse 3,000 mm/min Cedpfx Aerqwbiokcerb ➢ vertical 1,500 mm/min - Universal head with manual shaft lowering of 80 mm - Automatic lubrication with pump - Low voltage electrical controls on side arm push button panel - Star/delta start - Magnetic thermal protection from Siemens - Net weight 3,000 kg - Dimensions of the machine (for transport) Width 2,300 mm ➢ Depth 2,900 mm ➢ Height 2,400 mm Accesories - Counter supports for cutting shaft - Cutting shaft ø32 mm

Condition: new, Center length ----- 1000 mm Center height ----- 230 mm Crsdpfxjk Iug To Akcsb Turning diameter ----- 460 mm Passage of main spindle ----- 58 mm Bed width ----- 300 mm Spindle speed ----- 25-2000 rpm Motor ----- 5.5 KW Weight ----- 1750 kg INCLUDING * 3-axis digital readout brand SINO * Quick-change chisel holder type Multifix TOOB2 with 4 attachments * Self-centering 3 chuck 250 mm * Independent 4 chuck 320 mm * chuck 350 mm * Fixed and moving grips * LED work light and cooling system * Electric brake (CE) * Foot brake * Box with various tools

Condition: refurbished (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: SL154SY, turning length: 750 mm, turning diameter over cross slide: 510 mm, turning diameter: 680 mm, spindle motor power: 7,500 W, spindle speed (min.): 50 rpm, spindle speed (max.): 5,000 rpm, spindle bore: 56 mm, travel distance X-axis: 215 mm, travel distance Y-axis: 70 mm, travel distance Z-axis: 550 mm, mount diameter: 20 mm, rapid traverse X-axis: 18,000 m/min, rapid traverse Y-axis: 6,000 m/min, rapid traverse Z-axis: 24,000 m/min, rotational speed (max.): 3,000 rpm, rotational speed (min.): 20 rpm, type of input current: three-phase, feed length X-axis: 215 mm, feed length Y-axis: 70 mm, feed length Z-axis: 550 mm, torque: 70 Nm, bar passage: 56 mm, total height: 2,015 mm, total length: 3,336 mm, total width: 1,873 mm, Equipment: rotational speed infinitely variable, MORI SEIKI SL154SY LATHE WITH LNS BAR FEEDER RENISHAW LASER CHECKED TOOLBOX. Cjdpfx Aoxddfvjkcerb MACHINE INSPECTED AND READY TO WORK IN OPTIMAL CONDITIONS.

Condition: used, Year of construction: 1996, spindle passage 80 mm max. turning diameter 395 mm Max. Turning length 750 mm Crodpfjxbtqvox Akceb control System TX 8H max. Spindle speed 3.150 U/min. CNC lathe | TRAUB - TNA 400 The machine is in a well-maintained condition. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags:TNA400 | TNA-400