Clamping bracket with T-slots

unbekannt 1667/1000/H1400 mm

Condition: used, Technical details: turning diameter over bed: 830 mm turning dia. over face-slide: 540 mm turning length: 3000 mm turning diameter over support: 540 mm centre distance: 3000 mm faceplate diameter: 800 mm Rapid feed X axis: 4 m/min. control: MTC K (Monforts) range of revolution per miute: 2 -1.600 U/min spindle passage: 88 mm tailstock taper ISO: MK6 tailstock quill stroke: 200 mm max. workpiece weight between centers: 1250 kg max. workpiece weight -without tailstock: 3000 kg turning dia. in gap: 1.200 mm length of gap: 310 mm Weight approx.: ca. 6.85 (ohne Späneförderer und Kühlmittelbehälter) t dimension machine xH: 2,55 x 1,1 x 1,29 m Cycle lathe Machine overhauled in 2010 Ledpfx Ajwmlknsb Ajhn Operation via control panel Thread cutting by calculation Interpolator of NC control Chip conveyor manufacturer Cable drag Three-jaw chuck D=500mm without clamping jaws Various accessories *

Condition: used, Technical details: turning diameter over bed: 1200 mm turning diameter over support: 800 mm turning length: 3200 mm length of gap: 600 mm center height measured in bed: 600 mm turning dia. in gap: 600 mm spindle turning speed - continuous: 4,6-545 / 22 steps U/min spindle passage: 90 mm feed: 1,4-510 m/min taper: MK6 total power requirement: 15 kW weight of the machine ca.: 10,0 t dimensions L x W x H: 6,20x2,00x1,80 m dimensions electric cabinet LxWxH: 0,55x0,33x1,0 m equipped with: face chuck diameter 1000m (4 jaw chuck) fourfold chisel taper steady rest closed, inside diameter 250mm revolving tail center conical turning device * Lhodpfx Aszuyfajb Aon

Condition: used, Table unit from a DROOP & REIN portal milling machine Clamping plate with T-slots made of cast steel gray cast iron Table unit with clamping plate and very solid guideway Table clamping surface 5500 x 2000 mm Travel of the table clamping plate approx. 3100 mm Table height 1050 mm Table load: max. 20 tons Ball screw: Ø 100 mm Thread pitch: 20 mm (single-start) - Processing table guided very stably on the bed - Metal telescopic guideway cover - comes from a DROOP & REIN portal milling machine - Longitudinal table movement via ball screw and SIEMENS servo motor - Clamping surface with 11 T-slots 28 mm - Drive via SIEMENS 1FT6134-6AB71-1AG2 servo motor with IC200448S/R encoder (RN 000 B25) Lodpfx Ajthuzpjb Aohn Total length 9500 mm Width 2000 mm Overall height 1050 mm dead weight 28 ton. good condition

Condition: used, Technical details: honing diameter: Ø 400 mm stroke: 600 mm Ledpou Ngybefx Ab Aehn throat: 390 mm table-size: 1.550 x 780 mm table surface area: 1.400 x 480 mm table:: fest total power requirement: 4,1 kW Weight approx.: 2,8 t dimension machine xH: 2,0 x 1,2 x 4,35 m Further technical details: - longitudinal travel of machine table approximately 500mm - cross travel of machine table approximately 200mm - working height 350mm (non-adjustable) - distance column / table 0 - 200mm Equipment: - oil tank Ø 300 x 600mm - control panel i.D. *

Condition: used, functionality: fully functional, Year of construction: 2007, operating hours: 22,372 h, laser hours: 11,345 h, laser power: 4,000 W, sheet thickness steel (max.): 20 mm, sheet thickness aluminum (max.): 8 mm, overall weight: 16,000 kg, total length: 11,600 mm, total width: 5,200 mm, total height: 2,200 mm, working range: 40,002,000 mm, Equipment: cooling unit, Standard Features: Ledpfx Abjv Sm Ruj Ashn • Enclosed machine frame with integrated laser unit • Laser unit: TruFlow 2000 CO₂ laser with high-frequency excitation, maintenance-free turboradial blower, reflector telescope, cooling unit, logbook function • Automatic pallet changer • Longitudinal conveyor belt for small parts/waste • Drive: Maintenance-free three-phase servo motors • Cutting head quick-change device Laser cutting head with 5" lens and laser cutting head with 7.5" lens • Programmable cutting gas pressure setting • ControlLine capacitive height control and process control • Automatic focus adjustment with FocusLinePlus • Laser power control • Positioning laser • NitroLine high-pressure cutting • Fast processing with SprintLine • Automatic production of smaller holes • PlasmaLine plasma sensors • Automatic sheet metal surface and edge detection • Programmable Performance cycles • Microweld • Spray device for safe thick sheet processing • Automatic blow-off system • Residual heat extraction • Sinumerik 840D control system: Open PC-based control, easy operation, online help, integrated e-shop, diagnostic functions, maintenance logbook, technology data, teleservice • TruTops Laser lite workshop programming Safety: • Multi-beam light barriers, fully encapsulated and ventilated beam guidance, monitoring system, multi-chamber extraction and compact dust extractor, protective cabin • RJ45 network connection via installation via teleservice • 3.5" floppy disk drive • TFT color display More powerful lasers: • TruFlow 4000, including NitroLine Plus, nitrogen beam tube ventilation and lens monitoring sensors Extended machine equipment: • PierceLine Process Control System • A total of 2 Machine auxiliary pallets, structural steel webs • Crane-mounted traverse for manual pallet handling • Pneumatic cutting

Condition: used, Technical details: table length: 3600 mm table width: 3600 mm table load: 50 t table travel: 2000 längs / longitudinal mm table height over floor: 1350 mm table speed: ca. 1000 mm/min table rotating: 360 ° total power requirement: 14 kW weight of the machine ca.: 38,5 t dimension machine xH: 5,5x3,7x1,4 m space requirements of the machine approx.: 6,2x3,7x1,4 m Main areas of application: -Multi-sided machining -Supplement for travelling column milling machines or boring mills Electric and mechanics of the Rotary Table have been overhauled. - newly equipped with a digital measuring system (DRO) for x-travel and rotation - control via control panel - table clamping plate 14t weight - table load capacity 50t 11 pcs T-slots according DIN 650: - a=42mm - h=75mm - b=70mm - c=31mm Rotary Table can be inspected under power! Following work has been proceeded: - Integration of a Digital Read Out (DRO) for the x axis and a rotary encoder for C-axis - integration of a control via a control panel - renewal of hydraulic pipes / hoses, screw connections, manometers, flow chokes and filters - bearing of both axis transmissions - control cabinet and complete machine cabling has been renewed - end positions cleaned, checked, adjusted and defective replaced by new ones - frequency converter for continuous speed retrofitted - preparation of the necessary documentation (operating instructions, electrical and hydraulic diagram) - cracked gearbox housing repaired via casting lock - renewal of the guideway wipers - processing of the guideway cover including new wipers - machine has been repainted Lsdpeu N D Rqsfx Ab Ajhn - renewal of axis drives - feed gear cleaned and resealed - feed motor new bearing installed *

Condition: new, Year of construction: 2025, functionality: fully functional, turning diameter over cross slide: 420 mm, spindle bore: 103 mm, turning diameter: 660 mm, turning length: 3,000 mm, spindle speed (max.): 1,320 rpm, spindle speed (min.): 9 rpm, spindle motor power: 15,000 W, Equipment: rotational speed infinitely variable, Immediately available. No waiting, start machining right away! Machine: MEXPOL TUB 660 x 3000 mm with stepless speed adjustment via frequency inverter Bed width: 560 mm Distance between centers: 3000 mm Center height: 330 mm Spindle bore: 103 mm Workpiece weight: up to 3000 kg Spindle nose: DIN 55027/11 Speed range: 9 – 1320 rpm Ljdpfx Abeyr Dmke Ashn Main drive: 15 kW Feed rate: longitudinal feed 0.039–18 mm/rev, cross feed 0.02–9 mm/rev Rapid traverse: longitudinal 3800 mm/min, cross 1900 mm/min Tailstock: Quill diameter 105 mm, Stroke 225 mm, MT6 Thread cutting: metric, inch, module, DP Standard equipment: frequency inverter, quick-change toolpost size C, coolant system, interlocked chuck guard, work light, change gear set, CE conformity Dimensions: 4970 × 1650 × 1500 mm Weight: 4750 kg Fixed steady rest (roller jaws) Ø 20–200 mm Fixed steady rest (roller jaws) Ø 180–430 mm Delivery: Immediate from stock (while stocks last)

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, 1. Waterjet cutting system with accessories, year of manufacture 2005, machine number: 95 246, Model 4060D, including: 2. Machine details: - NC 4060 D (Duplex with 6 cutting heads for abrasive cutting) - 1 x cutting table: 4200 x 6700 mm - X-axis travel: 2750 mm - Y-axis travel: 6470 mm - Z-axis travel (height): 250 mm - Positioning accuracy (X/Y): +/- 0.075 mm/m - Repeatability (X/Y): +/- 0.05 mm - Feed rate X: 10,000 mm/min - Feed rate Y: 10,000 mm/min - Feed rate Z: 4,000 mm/min Technical specifications: - 1 x Fanuc GE 300 i (NANO CNC) SYSTEM Control functions • 15-inch color LCD display (resolution 1024 x 768) • Machine control panel • 1.5 GHz Pentium III processor • Vertical and horizontal soft key bars • Slim operator panel with QWERTY keyboard • 40 GB program storage (hard disk) • 2 MB RAM for part programs • Windows 2000/XP operating system • Hand-held control unit (remote control) for easy axis positioning – 1 x MPG unit – 6 x WJS standard cutting heads mounted on holders (2 x 3 pieces) – 6 x SM 3000 abrasive metering units – 1 x IGEMS Standard or Professional – 1 x documentation – 2 x abrasive storage tanks, 1,500 l each Ledpoxgumcsfx Ab Aehn – 1 x sludge removal system, 3 x diaphragm pumps – 1 x wastewater tank 1,500 l – 1 x cascade tank – 1 x new stainless-steel cutting tank (4 x 6.7 m) - 10 m high-pressure hoses with fittings - 1 x KMT high-pressure pump, 100 HP, 4,100 bar, only 9,500 operating hours - Installation and maintenance by WJS personnel Machine connections: Electrical connection: 3 x 400 V+N+PE, 25 A, 50 Hz Compressed air supply: 600 l/min Air pressure (technically dried): 6.5 bar

Condition: new, Year of construction: 2026, load capacity: 5,000 kg, Column Lifting Rotating Device with 5-Ton Capacity Protec Syncrolift Rotating Device/Positioner Double Column, Wireless and Manual Remote Control Column Adjustment with Two Travel Modes Load Capacity 5000 kg, 360° Minimum Working Height: 700 mm Maximum Working Height: 1600 mm Speed: 0.5 rpm Lhsdpfowak U Esx Ab Ajn Clamping Plate Diameter: 700 mm Rotating Motion: 1.1 kW 2 to 10-Ton Capacity Available Upon Request

Year of construction: 1990, condition: excellent (used), used T-slot clamping angle Technical data: Dimensions Height 1120 mm Width 320 mm Slot width 20 mm with - 7 horizontal T-slots Lhsdpegwxmxjfx Ab Ajn used, in good condition