CNC Lathe

TRAUB TND 400

Condition: used, Year of construction: 1992, operating hours: 27,221 h, functionality: fully functional, machine/vehicle number: 474, turning diameter over cross slide: 240 mm, turning length: 800 mm, rotational speed (min.): 40 rpm, rotational speed (max.): 4,000 rpm, total height: 2,005 mm, total length: 2,953 mm, total width: 1,990 mm, type of input current: three-phase, overall weight: 4,300 kg, Last maintenance performed by INDEX-Werke GmbH & Co.KG on September 29, 2025. Chuck diameter: 200 mm Main drive: 30 kW Speed range: 40-4000 rpm Spindle bore: 65 mm Turning diameter over cross slide: 240 mm Turning length: 800 mm Cross slide with turret Tool positions: 12 Slide travel, cross/longitudinal: 220/850 Powered tools: 6 Speed at the drive wheel: 4000 rpm Guodpfx Asz Ng I Asfreh Tailstock Arbor diameter / Arbor travel: 85 / 140 Mount according to DIN 228: MK5 Total power: 52 kW Machine weight: 4300 kg Dimensions (L/W/H): 2953/1990/2005 Technical data subject to change without notice. Errors and prior sale excepted.

Condition: good (used), Year of construction: 2000, control type: NC control, controller manufacturer: Davi Smart, number of rollers: 4, roller (bottom) diameter: 340 mm, roller (top) diameter: 370 mm, side roll diameter: 320 mm, roller length: 3,100 mm, sheet thickness (max.): 25 mm, overall weight: 18,500 kg, total length: 5,900 mm, total width: 2,200 mm, total height: 2,300 mm, power: 30 kW (40.79 HP), Equipment: cone bending device, 4 roll plate bender Davi Promau - MCB-3037 Gusdpfozi Ra Rex Afrsh MACH-ID 9751 Make: Davi Promau Type: MCB-3037 Control: Davi Smart Year: 2000 Conical bending attachment Extended roll end for section bending jobs Digital read out position side rolls Central lubrication CE-Declaration Rolling width: 3100mm Rolling thickness 3x toproll Ø:20mm Rolling thickness 5x toproll Ø:25mm Rolling thickness prebending: 22mm Top Roll Ø: 370mm Bottom Roll Ø: 340mm Side roll Ø: 320mm Number of rolls: 4 Rolling speed: 0-5 Adjustiment lower roll: 0-200mm/min. Adjustment side rolls: 0-200mm/min. Number of driven rolls: 2 Power: 30kW Length: 5900mm Width: 2200mm Height: 2300mm Weight: 18500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, CNC turning machine TRAUB, Type TND 400 Serial No. 708, Year of manufacture 1996 CNC control TRAUB TX 8 F Nominal turning diameter: 400 mm Swinging diameter over bed: max. 470 mm Spindle bore in draw tube: 65 mm Motor power, spindle drive: 22 kW Total power consumption: 35 kW Mains connection: 380 volts, 50 Hz - Electronic handwheel - RS 232 data interface - Turret with 12 tool positions, VDI 40 - Includes 8 tool holders, VDI 40 - 3-jaw chuck, Ø 225 mm, SMW Autoblok, Type KNCS-N-Ø 225-65 Includes a large quantity of chuck jaws - Hydraulic internal expanding cylinder, SMW, Type ZHDAS-130-67 - Chip conveyor, KNOLL, Type 200 S-1/600 - Coolant system - Hydraulic unit (L x W x H 650 x 500 x 1000 mm) Space requirement L x W x H: 4800 x 2000 x 2100 mm Space requirement, base machine L x W x H: 3500 x 2000 x 2100 mm Gusdpfezacwdex Afroh Space requirement, chip conveyor L x W x H: 4500 x 700 x 1550 mm Weight: approx. 5 tons Good condition Machine is ready for demonstration. The internal expanding cylinder for workpiece clamping needs to be repaired.

Condition: ready for operation (used), Offered is a Traub TND 400. Center distance: 800mm, turning diameter approx. 250mm, travel X/Y approx. 220mm/850mm, spindle bore: 65mm, speed range: 40-4000rpm, 12-position disc turret, tool holder: VDI40 DIN69880, integrated coolant system, dimensions X/Y/Z approx. 3000mm/2000mm/2000mm, weight approx. 4300kg-4500kg. Inspection by appointment possible. Godpfx Afeykutxorsuh

Condition: used, TECHNICAL DETAILS - maxi bar diameter : 12.7 [mm] - main headstock strokes (fixed/rotary sleeve) : 130/80 [mm] - spindle power : 4 [kW] - rotation speed : 12 000 [rpm] - upper turret : 6 positions - lower turret : 6 positions - number of rotary positions on turret : 6 - sub-spindle maxi diameter : 12.7 [mm] - sub-spindle rotation speed : 12 000 [rpm] - dimensions : 2850 x 110 x 1480 [mm] - hours in production : 12408 [H] - spindle hours : 9400 [H] Godpfxsuhav Do Afrsuh EQUIPMENT - CNC TRAUB TX 8i control - bar feeder LNS Alpha ST 320 - C axis on main spindle and sub-spindle - brake on main spindle and sub-spindle - parts catcher with conveying strip - anti fire device - lubricating tank with pump with cooling unit - chip conveyor - various fixed and driven tool holders

Year of construction: 1995, condition: ready for operation (used), Power supply: 75A, connected load: 35kW, control system: Traub SYSTEM TX 8F, weight: approx. 4.5t, operating hours: 84,126h, the machine has problems when machining inclined surfaces. An on-site inspection is possible. Gujdpfxoy Tx Rze Afrsh

Condition: used, Three Dimension Coordinate Measuring Machine MITUTOYO CRYSTA-Apex S574 Guedjy Ufkkspfx Afreh

Year of construction: 2007, condition: ready for operation (used), Cutting range round: 560mm, cutting range flat (W x H): 620/560mm, material feed length, single: 900mm, multiple feed: 9999mm, shortest cut length: 6mm, minimum diameter to be cut: 15mm, minimum remnant in single cut: 15mm, shortest remnant length in automatic mode: 80mm, saw motor power, frequency-controlled: 5.5kW, cutting speed, stepless: 13-127m/min, saw blade dimensions: 7400/54/1.6mm, material support height: 700mm, total drive capacity in basic configuration: 12kW, length: 2370mm, width: 3610mm, overall dimensions with chip conveyor (L/W): 2370/3610mm, machine table height lowered: 2230mm, weight: approx. 5.2t with chip conveyor. An inspection on site is possible. Godpfx Afsxg Rhvsrjuh

Condition: used, Year of construction: 2005, turning diameter 275 mm turning length 900 mm control TRAUB TX8i spindle passage 65 mm power capacity at 100 % load 25,20 kW power capacity at 40 % load 30,20 KW max. torque at 40% / 100% load 180 / 135 Nm spindle turning speed - stepless 1 - 5.000 U/min spindle diameter in front bearing 110 mm C-axis 1 - 500 U/min worktool support No. 1 x-axis 290 mm y-axis 165 mm z-axis 600/950 mm B - axis 360 ° rapid traverse X/Y/Z 18 / 18 / 30 m/min feed capacity X/Y/Z 10 / 10 / 7 kN number of tools 2x2 + 2x2 number of driven tools 2x2 + 2x2 mm toolpiece turning speed range 8.000 / 2.000 U/min power capacity at 25 % load 5,80 kW max. torque at 25% load 4x18,6 / 4x74 Nm tool taper TRAUB Ø60 worktool support No.2 / No.3 / No.4 x-axis 170 mm z-axis 600/950 mm y-axis +/- 60 mm rapid traverse X/Y/Z 18 / 15 / 30 m/min feed capacity X/Y/Z 10 / 10 / 7 kN tool turret - number of stations 10 number of driven tools 10 mm toolpiece turning speed range 1 - 6.000 U/min power capacity at 25 % load 5,80 kW Gjdpfsw E Nnbox Afrsuh max. torque at 25% load 18,60 Nm tool taper DIN 69880 Ø40x63 bar loader DNH61 / 3000 Bar length 1.000 - 3.200 mm bar material dia. 18 - 63 mm hexagon max.45 mm total power requirement 95,00 kW weight of the machine ca. 16,00 t dimensions of the machine ca. 10,00 x 3,50 x H3,00 m With TRAUB TX 8i control unit, main and counter spindle with C-axis, 3 turrets, 1 vertical-tool-carrier with B-axis, dust exhauster, chip conveyor, coolant system with coalescence-separator. Barfeeder TRAUB Stamag DNH61 /3000 2 pc. 3-jaw chuck SMW KNCS-N 170-43 2 pc. HAINBUCH Spanntop chuck 40 pc. various tool holder non-driven 6 pc various tool holder driven Spare parts package Machine can be inspected under power.

Condition: new, pressure: 600bending length: 6050column width: 5100daylight: 680stroke lenght (max.): 455column throat depth: 450messurements (LxWxH): 7100x3275x3910weight approx.: 50.2004 axes (Y1, Y2, X, R): Ja alle Achsen über die Esa S630 (2D Grafik Steuerung)CNC crowning system by control: ja über die Esa S630 (2D Grafik Steuerung)motor power: 45Standard Equipment:KK Kletzer Europa We have developed a high-quality model specifically for the European market:The CNC press brake by KK Industries, made in Turkey. Model: KK Kletzer EUROPA XL The powerful EUROPA XL press brake stands out for its high precision, accuracy, and versatile offers a very large open height, resulting in a long cylinder stroke, and an extra-large throat depth to provide maximum flexibility during operations. We focus on delivering quality—reflected also in the control system:As standard, the machine comes equipped with the ESA S640 2D graphic controller. Additionally, the KKI EUROPA XL is equipped with CNC-controlled Y1, Y2, X, and R axes via the wning is also included and fully CNC-controlled through the same ESA S640. When it comes to tooling, we make no machine is fitted with premium top tools and dies from EUROSTAMP Italy. Naturally, a machine is only as good as the service behind t’s why we rely on highly qualified staff with many years of experience in CNC sheet metal processing. Technical Highlights: CNC axes: Y1, Y2, X, and R Controller: ESA S640 (2D graphical interface) Backgauge with double linear guides and ballscrews Motorized CNC-controlled crowning system Heavy-duty height adjustment with handwheel(from 175 tons: on linear guides) Laser safety system on the upper beam Gjdpfx Afsd Ehh Rereuh CE-compliant safety equipment Various options available Optional Controllers: ESA S640 – 15” 2D Touchscreen: ¤ 4,520.00 ESA 675 W – 21” 3D Touchscreen (Windows-based): ¤ 6,485.00 DELEM DA-66T – 17” 2D Touchscreen (Windows-based): ¤ 10,165.00 DELEM DA-69T – 17” 3D Touchscreen (Windows-based): ¤ 16,350.00