Coating surface treatment system

Surfin Technology TRP501

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators. Ledefz U S Eepfx Ancoaa

Year of construction: 1993, condition: good (used), machine/vehicle number: 03.2370, Arthur Klink - internal broaching machine (WAG 748) machine type: internal vertical hydraulic broaching machine manufacturer: Arthur Klink type: RISZ 10 x 1000 built in: 1993 stroke: 1000mm pulling force: 10.000KG working stations: 3 PCs drive: hydraulic system equipment: coolant system, magnetic chip conveyer remark: machine under power in stock the machine has an automatic workpiece loading system for 2 workpieces, ideal useable for high production Lajdpfxocc D Dde Ancoa Optional accessories available on request: tools, workpiece holder Information about us: we are specialized for second hand broaching machine and still have anytime about 80 pcs of used broaching machines in our stock, vertical and horizontal machines from 3000kg up 63.000kg pulling force and from 1000mm stroke up to 3500mm stroke.

Condition: used, Year of construction: 2020, functionality: fully functional, operating hours: 1,000 h, Kovo Staněk TZNZ 5-11/16-36 (2020) – High-Performance Hanger Shot Blaster Type: overhead rail / hook (CE) • Year: 2020 • Total weight: 12,000 kg • Condition: excellent, production-ready. Capacity & Power Max workpiece: Ø 1600 × 3600 mm (H) Max hook load: 1000 kg Throwing wheels: 5 × 11 kW, rotor Ø 350 mm (individually fed) Abrasive hopper: approx. 1800 kg Air demand: 20 m³/h at 6 bar Noise level: ≤ 85 dB(A) Ljdpfexpiw Ujx Ancoaa Machine size (W × D × H): 4730 × 5070 × 6520 mm Mains: 400/690 V, 50 Hz • Control voltage: 24 V DC Control & Automation PLC (NX platform) with touchscreen HMI and remote service access. Up to 99 programs with per-job settings: blast time, turbine speed, hook rotation and speed, swing angle of turbine block, servo abrasive flow per wheel, automatic conveyor start/stop. Diagnostics and full interlocking on doors and motions. Wear Protection & Build Blasting chamber lined with XAR500 wear plates (5 mm) and manganese steel X120Mn12 in formed/high-wear zones; replaceable rubber in impact areas. Wheel internals (blades, cages, liners) made from tool steel 1.2379 / X153CrMoV12 (~62 HRC). Heavy welded turbine block housing. Service platform with safety gate and Total Stop. Abrasive Circuit Designed for steel shot S330 (initial charge about 1.5 t). Elevator → air separator → shared hopper loop; magnetic/air cleaning maintains media quality. Servo dosing to each wheel ensures uniform intensity and reduced consumption. Extraction & Filtration CIPRES CARM dust collector, 7.5 kW fan, automatic back-draft flap; ducting includes automatic valve for cabin purge at cycle end. Handling System Powered monorail with adjustable speeds; servo-driven hook rotation and lift; pneumatic diverter switch; two 1.1 kW hoists. Timed sequence allows loading the next batch while blasting. Applications Forgings, castings, welded structures and general steel fabrications—surface preparation before painting, galvanizing or coating with high throughput and repeatable Sa 2½–3 results. Key Advantages 5 wheels for high coverage and speed • PLC plus servo precision • XAR and manganese lining for long service life • 12-ton EU build • Low noise ≤ 85 dB(A). Available for inspection on request via the platform.

Condition: new, Year of construction: 2025, functionality: fully functional, power: 88 kW (119.65 HP), temperature: 220 °C, heating capacity: 30 kW (40.79 HP), workpiece height (max.): 1,500 mm, workpiece length (max.): 500 mm, insulation material: Steinwolle, insulation thickness: 150 mm, workpiece width (max.): 500 mm, Scope of delivery: 1. chemical pre-treatment by spraying (in cycle process) 2. dryer 3. powder coating system 4. single powder oven 5. conveyor technology, semi-automatic 6. electrical control system Hall/ floor space Floor area of the system max. 12,000 x 6,500 mm Hall floor Industrial floor Workpiece sizes Max. Part dimensions L= 500mm, H= 1,500mm, W= 500mm Range of steel parts Conveyor technology P&F chain conveyor in cycle mode, semi-automatic Pre-treatment Chemical Power supply Electricity On-site power (max. 88 kW) Gas On-site power Compressed air On-site power Water On-site power Calculation Type of system Cycle system Conveying speed 3.2 meters / min Length per cycle L = 1,600 mm Time for cycle movement: Tm = 1.6 meters : 3.2 meters/min = 0.5 minute Time for cycle standstill: Ts = 8.5-12 minutes Total time for cycle Tt = Tm + Ts = 9-12.5 min Electrical energy: Total power 88 kW Lsdpfoulwg Njx Anceaa min. Average consumption 60 kWh max. average consumption 70 kWh

Condition: good (used), Year of construction: 2014, Technical data shown on photos. Lsdjufp Svopfx Ancjaa Parts shown by hand not come.

Condition: good (used), Year of construction: 2006, I sell the automatic pneumatic end cutting saw Weinig Grecon Dimter Opticut 200 Elite Year 2006 Motor power 7,5kW Input table automatic feeding 4,10m (throughfeed system) Outut table automatic 6 pcs. kickers on right outfeed table Optimising with mistakes deffect reading and automatic cutting sequence modes. Lasdpfx Ajxtxi Isncsa Available immediately. CE version. Documentation included.

Condition: new, SAPI Powder Coating The Perfect Coating for Lasting Protection. Powder coating is a highly effective and widely used method for applying a protective and decorative surface to various types of substrates. It is a dry finishing process where a fine powder made of resins, pigments, and additives is applied to a substrate. The powder is electrostatically charged, allowing it to adhere evenly to the surface and form a uniform coating. To achieve optimal adhesion and durability, the substrate is thoroughly cleaned and prepared first. Oils, dirt, and other contaminants are removed to ensure a clean surface. This is crucial for ensuring that the powder bonds effectively to the substrate, creating a strong and long-lasting coating. Components of a Powder Coating System A typical powder coating system consists of several components and devices required for applying and curing the powder coating. Spray Booth and Spray Area The booth provides a clean environment for the application process and ensures an even distribution of the powder. 🎨 Powder Coating Gun A powder coating gun is used to apply the powder coating to the workpiece. 💨 Powder Feed System The powder feed system consists of a hopper or container where the powder coating material is stored. It typically includes devices like powder pumps, feed hoses, and powder sieves to transport the powder from storage to the spray gun. 🔄 Pre-treatment Equipment Pre-treatment systems are used to prepare the substrate before applying the powder coating. This can include processes like cleaning, degreasing, rinsing, and surface treatment to ensure proper adhesion and durability of the coating. 🧼 Curing Oven A curing oven is a crucial component of a powder coating system. It is used to heat the coated substrate to the correct temperature so the powder coating melts, flows, and hardens into a permanent surface. The oven usually consists of a conveyor system or racks to transport the coated parts through the oven chamber. 🔥 Lodjun Sd Uopfx Ancjaa Exhaust System An exhaust system is installed to remove excess powder, fumes, or volatile compounds generated during the coating process. It helps maintain a clean and safe work environment for the personnel and prevents the accumulation of powder particles in the air. 🌬️ Looking for a Powder Coating Solution? Are you searching for a custom powder coating solution? We specialize in providing tailored powder coating solutions to meet your individual needs. Whether you have specific color requirements, complex designs, or challenging substrates, our experienced team is ready to deliver exceptional results. 💡 Contact us today to discuss your requirements, and let us develop a custom powder coating solution for you. 📞 Get in touch with us today!

Condition: used, Year of construction: 2011, operating hours: 7,003 h, fuel type: diesel, Equipment: cabin, head guard, * Total weight: 12,650 kg * Year of manufacture: 2011 * Maximum load capacity: 3,800 kg * Remote control Ledev Sl Dgopfx Ancsaa * 4 hydraulic outriggers * Roto-steering * All-wheel steering * Front-wheel steering * Crab steering -----Internal vehicle number: 10736----Subject to errors and prior sale.

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Vacuum system (with its pump) N. 4 Vertical supporting columns of the top supporting beam N. 1 Horizontal top supporting beam (where the carriage slide on) N. 1 Motorized sliding carriage with horizontal metal arms N. 2 Horizontal metal arms with vacuum cups, adjustables N. 2 Out-side rollers ways (on gound) to in-feed pile of panels to the Loader N. 1 Out-side motorized rollers table (which in-feed the panels to the Unloader), with also cross motorized conveyor belts (at 90°), dimensions mm 7232 (ca.) Separate electric and command panel Electronic Programmer OMRON Perimetral safety metal grids Working capacity (cycles/min) 16 - 20 (ca.) Min/Max panels thickness mm 10 - 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1200 x 3200 (ca.) Total installed motor power Kw 23.3 Laodpfxsd Rg Dpo Ancsa

Condition: new, Year of construction: 2025, functionality: fully functional, total length: 30,000 mm, total height: 4,300 mm, total width: 6,500 mm, workpiece weight (max.): 100 kg, temperature: 220 °C, heating capacity: 80 kW (108.77 HP), workpiece height (max.): 1,200 mm, workpiece length (max.): 2,500 mm, insulation material: Mineralwolle 75 kg/m³, insulation thickness: 150 mm, workpiece width (max.): 800 mm, The continuous system consists of the following components: Chemical pre-treatment by spraying Dryer Powder coating system Powder curing oven Conveying technology (cycle process) Lsdpfeum Uflex Ancoaa Electrical control system