Blowing Machine SIDEL

Sidel SBO 6

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons Fpodpsg Ailcofx Akyon PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: used, Year of construction: 2000, Overview  This PET blow-moulding machine was manufactured in 2000 by French company SIDEL. The machine is currently in good working condition, running in production until the end of November 2025. It will be dismantled and craned out through the roof, with craning scheduled for December 2025. It becomes available after dismantling. Technical data - Capacity: - 7,600 bph on 1.0 L - Formats: - Neck finish 29/21 - Preforms processed: RPET Plastipak & Resilux - Number of moulds: - 6 (moulds not included) - Equipment & Features: - Quick change for shell molds - Sidel caterpillar oven - 6 heating modules - Sidel preforms tipper - Sidel preforms hopper & feeder - Sidel preforms infeed rail - Sidel caterpillar oven & blowing wheel - Solenoid valves Sidel Universal type - Sidel PCC version V2.02 - Sidel CE electrical cabinet (Siemens) - Service history: - Sidel maintenance completed September 2024 - Elongation sensor retrofitted - Additional service by client’s technicians Scope of Delivery  - Stretch blow-moulder SIDEL SBO 6 Series 2 Fsdpfxsyb Tbpj Akyopn - Preforms tipper - Preforms hopper & feeder - Preforms infeed rail - Caterpillar oven & blowing wheel

Condition: ready for operation (used), Year of construction: 1993, functionality: fully functional, product height (max.): 380 mm, workpiece diameter (max.): 130 mm, production capacity: 7,200 unit/h, TECHNICAL DETAILS Number of cavities: 6 Capacity with standard bottles: up to 7,200 bph Product formats Bottle volume: 0.25 – 3.0 L Max. bottle height: 380 mm Max. bottle diameter: 130 mm Preform dimensions Max. preform length: 210 mm Fsdpfxox A Uu Ee Akyopn Neck inner diameter: 34 mm MACHINE DETAILS Dimensions & Weight Blow module dimensions: 2,000 x 2,200 x 2,200 mm Blow module weight: 8,000 kg Oven dimensions: 3,000 x 1,100 x 2,100 mm Oven weight: 2,000 kg Control cabinet dimensions: 1,500 x 1,000 x 2,100 mm Control cabinet weight: 1,000 kg Transformer 415V / 380V dimensions: 1,000 x 500 x 2,000 mm Transformer weight: 500 kg Preform hopper and conveyor dimensions: 3,000 x 1,500 x 3,500 mm Preform hopper and conveyor weight: 600 kg Preform feeder dimensions: 2,000 x 2,500 mm Preform feeder weight: 250 kg Infeed guide rail length: 2,000 mm Power supply Total power: 142 kW Mains connection: 380/420 V +/- 10%, 50 Hz +/- 1% Cooling water Cooling capacity: 16,000 kcal/h Water temperature: 10 – 12°C Flow rate: up to 6.0 m³/h Water pressure: 5 – 6 bar Compressed air Service air pressure: 7 bar Service air flow: 50 – 100 Nm³/h Blowing air pressure: up to 35 bar Blowing air flow for 0.25 – 3.0 L: 155 – 770 Nm³/h EQUIPMENT Transformer 415V / 380V Preform hopper and conveyor Preform feeder Infeed guides Adaptation to other voltages possible

Condition: used, Year of construction: 1992, Overview This complete automatic can filling line has a nominal output of approx. 20,000 cans/hour for 330 ml cans (can type 211/202), packed 24 cans per foil-shrunk tray. The core is an O+H / KHS Hansacan filler with 30 filling valves, mechanically blocked to a Ferrum F 505 G seamer with 5 seaming heads. Empty cans are supplied by a TMG Impianti Vega 120/B depalletizer and rinsed on a Hysek Rinsstar 20000 rinser before filling. A date/coding printer is not included. Technical data - Line type: Complete automatic can filling line - Nominal output: approx. 20,000 cans/hour (330 ml), product- and temperature-dependent - Container: 330 ml can, can type 211/202; 24 cans per foil-shrunk tray - Controls: PLC Siemens S7, Siemens SIMATIC HMI - Warmer and drying station reconditioned; fill-height control and packaging machine new Equipment - Can Depalletizer | TMG Impianti | Vega 120/B | tier-sheet removal, can table, pallet magazine | 2014 - Can Rinser | Hysek | Rinsstar 20000 | filtered-water rinse | 2001 Fpjdpfozlqu Tex Akyen - Can Filler | O+H / KHS | Hansacan | 30 filling valves, fixed for can type 211/202, will be general overhauled | 1992 - Can Seamer | Ferrum | F 505 G | 5 seaming heads, blocked with the filler | 2010 - Can Warmer | SMB | stainless-steel tunnel | warms cans to approx. 25 °C before packaging | reconditioned - Fill-Height Control | Heuft | incl. pushing/reject station | new - Can Drying Station | Gesete | air-dries cans before coding | reconditioned - Packaging Machine | Termo Pack | UMT-1500 | tray erector, packer and foil shrink | new - 2x can turning stations (330 ml can) - Can conveyor system incl. electrical control panel (PLC Siemens S7) - Tray conveyor system incl. drive station Condition Used line delivered in reconditioned or new condition. The filler and Ferrum seamer are reconditioned and blocked as one unit with a new electrical panel (PLC Siemens S7), new pneumatic panel and renewed pneumatic valves; the can warmer and can drying station are reconditioned; the fill-height control and packaging machine are supplied new. This work is carried out as part of the order, so the line is supplied component by component and is not yet assembled or tested as one running unit. The can depalletizer is the exception - it is already fully reconditioned and in stock. Filler and seamer are delivered with CE declaration and full documentation. Components can be inspected on request. Availability On request; delivery time as per agreement. Reconditioned and new-build components are supplied with a lead time after order. Location and inspection on request.