SCHNELL Robomaster 6012 bending robot

SCHNELL Robomaster 6012 bending robot

Year of construction: 1997, condition: ready for operation (used), Wire diameter (single wire): 6mm-14mm, wire diameter (double wire): 6mm-10mm, maximum bending angle: 180°, motor power: 22kW, feed rate: 1.5m/s, bending speed: 1000°/s, cutting time: 0.4s, hydraulic tank volume: 300l. Machine dimensions X/Y/Z: approx. 4900mm/1640mm/2200mm, weight: approx. 3300kg. Control system defective. Documentation available. On-site inspection is possible. Fpsdpfouwrv Dex Aalsg

Condition: good (used), Year of construction: 2013, grinding diameter 140-355 mm grinding length 3000 mm centre height 260 mm weight of the machine ca. 8,3 t dimensions of the machine ca. 8500 x 3500 mm SA 6Ux3000 external cylindrical grinding machine Year of manufacture: 1981 Retrofit: 1 x 2013 SERWEMA Maximum grinding diameter with tailstock: 140 mm Maximum grinding diameter without tailstock: 355 mm Maximum grinding length: 3,000 mm Fjdpfxsynmpyo Aalopg Center height 260 mm Workpiece weight max. 500 kg Machine footprint 8500 x 3500 mm Machine weight 8500 kg

Condition: refurbished (used), Year of construction: 2011, Used automatic hydraulic bandsaw for metal MEP SHARK 332 NC EVO Blade dimensions: 3320x27x0.9mm Mitre angle: from 45° to +60° Operating modes: manual, semi-automatic dynamic, semi-automatic, automatic Cutting speed: 15-100m/min (inverter) Cutting capacity: at 0° - round 300mm - square 260mm - rectangle 330x260mm Dimensions: 2600x2320x2000mm Year of manufacture: 2011 Weight: 1050kg Fpjdpfeul Svlox Aaleg The machine is fully refurbished and tested.

Condition: used, Year of construction: 2016, functionality: fully functional, working width: 2,000 mm, wire diameter (max.): 6 mm, type of input current: three-phase, operating speed: 142 mm/s, mesh size: 9,999 mm, continuous power (apparent): 833 kVA, We offer a used Schlatter MG600/MG24.4/10Sp-AC mesh welding machine, model year 2016. Type: MG600/MG24.4/10Sp-AC Serial number: 4885.31609 Year of manufacture: 2016 Rated primary voltage U1N: 400 V Rated secondary voltage Ua: 230 V Primary phases: 3 ~ Secondary phases: 1 ~ Frequency: 50 Hz Fsdpfx Aajyaqzqslopg Rated apparent power Sp: 833 kVA Rated primary current I1,p: 1202 A Primary short-circuit current I1cp: 50 kA Secondary short-circuit current I’acp: 10 kA If you have any questions or require further information, please feel free to send us a message or call us.

Year of construction: 2003, condition: refurbished (used), machine/vehicle number: 50/140/03, GENERAL CHARACTERISTICS Ø Grinding Wheel Dimensions (OD x ID x width) 508 mm Regulating wheel width 254 mm Diamond dressing speed Ø508 x 254 mm Lubrication (Auto/Manual) centralizado automático / automatic lubrication CNC Brand FANUC CNC Model Series 18i - T CNC Axes Nº 8 Grinding wheel width 254 mm Fpsdpfx Aaed Nw T Ioleg ELECTRICAL CHARACTERISTICS Total Power 25 kW Voltage 220/380 v DIMENSIONS AND WEIGHTS Long 2150 mm Width 2200 mm High 3400 mm Weight 8000 kg

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, input voltage: 400 V, year of last overhaul: 2023, ATTENTION: THIS MACHINE AT A ONE-TIME SPECIAL PRICE. General description: Year of construction: 2001/2023 Manufacturer: Emag Machine type: VL3 Technical Data: Control: Fanuc 21i-T Rotation diameter: approx. 210 mm Maximum speed 6,500 1/min Turret: VDI 40 mm, 12 stations The machine does not have a life tool. Hinged belt chip conveyor Spindle holder: GR. 5 Circulating parts conveyor. Machine weight: approx. 5.5 t The following work was carried out during this overhaul in 2023: -Machine was completely dismantled, cleaned and repainted, The main spindle was re-supported -The guides and guide shoes were replaced in the X-axis and Z-axis -The ball screw in the X-axis and Z-axis was replaced -New unit for central lubrication and new hoses -Hydraulic unit was checked and serviced. Drive coupling between motor and pump was replaced -Cooling unit was checked and serviced: Temperature difference controller was replaced - Clamping cylinder was re-mounted and sealed. Gearbox of the A-axis was re-mounted and coupling between motor and gearbox was replaced -Electrical cabinet was cleaned -Control panel was replaced -New screen -New interior lighting -Turret was dismantled, wearing parts checked, cleaned and resealed -Cleaned turret encoder and encoder wheel -Length measuring systems in X-axis and Z-axis disassembled and cleaned -Pick-up station springs replaced Fpsdpotpu Szjfx Aaleg -X-axis and Z-axis motors were checked for bearing damage -The windows on the work door were replaced. -The chip conveyor was completely dismantled, re-stored, cleaned and painted -Of course, various small parts of the machine were also replaced The product has been described by us with the utmost care. The description is non-binding and should be checked during an inspection.

Condition: used, Technical details: bending angle max.: 0 - 225 ° working height: 850 mm Fpsdpfex Adbnsx Aaljg operating voltage: 380 V bending angle max.: 0 - 225 ° number of bars max.: 15 mm diameter max.: 55 mm revolutions per minute: 5 -16 U/min total power requirement: 5,5 kW Weight approx.: 0,7 t dimension machine xH: 1,60 x 1,20 x 1,02 m Reinforcing Steel Bending Machine Perfekt 55 KA, PA, PLA — high-performance production machine. Thanks to the control system with four different bending speeds, the machine operates with exceptional efficiency. The bending angle is continuously adjustable from 0 to 225 degrees for left or right rotation. With its correction potentiometer for material spring-back compensation, the machine is ideal for medium and large-scale series production. Using the PA program control unit, up to eight different bending angles can be continuously pre-programmed from 0 to 225 degrees via rotary knobs. without accessories! *

Condition: excellent (used), Year of construction: 1991, swing diameter 400 mm Q U O T A T I O N We are pleased to offer you ex our stock, subject to prior sale, and error in technical data : WMW - GLAUCHAU Hydraulic Internal Grinding Machine with Face Grinding Device model SI 6/1 AS-N x 315 year 1991 Internal grinding diameter 40 - 400 mm Internal Grinding depth, max. 315 mm Max. grindable External dia. 400 mm Weight of workpiece without steady, max. 630 kg Workpiece Swing Ø, with / without safety hood, max. 500 / 600 mm Height of centre above table 360 mm 16 step workpiece spindle speeds 40 – 400 rpm Workpiece spindle bore, approx. 53 mm Workpiece headstock swivelling max. 30 ° Adjustment of workpiece headstock position crosswise, max. 400 mm Automatic cross traverse of grinding head 70 mm Adjustment of grinding head position on slide crosswise, approx. 100 mm Feed of grinding head, intemittendly 0.001 – 0.025 mm/stroke Feed of grinding head, continually 0,1 – 1 mm/min Table stroke, max. 630 mm Table speeds infinitely variable 0,1 – 8 m/min (10 m/min) Distance workpiece headstock and grinding slide, max. 1,250 mm Adjustment of Grinding spindel stock on table 520 mm Spindle drive, approx. 7.5 kW Total electrical load, approx. 17 kW - 380 V - 50 Hz Weight, approx. 6,000 kg Accessories / Special Features: • Universal internal grinding spindle head with automatic cycles to grind cylindrical and conical bores with one or multiple diameters, external diameters and grinding of narrow end-faces. • Face grinding device, hydraulic swivel-in, with automatic cycles to grind end-faces, multiple end-faces and two tiered end-faces simultaneously Fodpfx Ajxyllvjalepg • Electronic cycle control with control tableau to set up all the grinding and dressing cycles including ampere-meters for internal grinding spindle and face grinding spindle • Belt-type grinding spindle drive with mounted grinding spindle and 5 pieces separate interchangeable grinding spindles along with various pulleys with various diameters. • Dressing device for both grinding spindles • HEIDENHAIN Digital Read-Out for the cross adjustment of the Workpiece headstock • A large amount of operating tooling and accessories as : 4-jaw Faceplate Ø approx. 520 mm, 3-jaw chuck Ø approx. 380 mm, 3-jaw-chuck Ø approx. 130 mm, pulleys, spindle sleeves, grinding flanges, foot switch, • Separate hydraulic unit, built on switch cabinet, coolant device with magnetic separator. Condition : very good, universal machine for all sorts of grinding tasks ! Please click here to view a video of the machine running : ! Delivery : immediately available, FCA Metzingen Payment : 100 % Net, after conclusion of contract, before loading

Condition: excellent (used), Year of construction: 2006, operating hours: 53,000 h, functionality: fully functional, Full-option CNC gear grinding machine in outstanding condition, previously used in special-purpose machinery manufacturing. The machine produces up to 200 different gear types/products for special orders in batch sizes from 1 to 10,000. Manufacturer: Reishauer Model: RZ 150 Type: CNC Gear Grinding Machine Year of manufacture: 2006 Fsdoyxrygspfx Aaljpg Serial number: 7XXXX Machine specifications: - 2 identical workpiece spindles - Workpiece spindles with tailstocks - Turret design - Enclosed machining area - External loading and unloading station - Especially designed for run-in gearings Equipment: - Grinding worm profiling device Reishauer RP 120 - Hoffmann belt suction filter system HSF 150 - OLAER cooling unit CD35.02-NE - OLAER designation PC31.02NE-S - ELBARON extraction/filter unit RON/A2000V-2V-RH - 5-axis robotic automation (optional) Operating data: - Total operating hours: approx. 70,569.5 h - Run-time / part counter workpiece spindle / workstation 1: counter reading 01794635 - Run-time / part counter workpiece spindle / workstation 2: counter reading 002929 Hoffmann belt suction filter system HSF 150 - Connection: 400 V / 50 Hz - Phases: 3 / PE - Operating voltage: 400 V - Connected load: 31.4 kW - Nominal current: 56.9 A - Control voltage: 24 V DC - PLC voltage: 24 V DC - Valve voltage: 24 V DC - Lamp voltage: 24 V DC OLAER cooling unit CD35.02-NE / PC31.02NE-S - Year of manufacture: 2005 - Refrigerant: R134a - Fill quantity: 2.1 kg - Max. permissible operating overpressure HD: 21.7 bar - Max. permissible operating overpressure ND: 10.6 bar - Voltage: 400 V / 3 Ph / 50–60 Hz alternative: 480 V / 3 Ph / 60 Hz - Max. current: 5 A - Power: 2.5 kW ELBARON RON/A2000V-2V-RH - Year of manufacture: 07/2005 - Weight: 74 kg - Connection: 3 x 400 V AC / 50 Hz alternative: 1 x 230 V / 60 Hz - Power: 3.56 kW - Current: 7.0 A - Protection class: IP54 - High voltage max.: 9.9 kV DC - Current max.: 24.8 mA Condition: - Machine under power - Operated in single-shift to two-shift operation - Preventatively maintained - Very well-kept condition - Comprehensive documentation available Scope of delivery: - Without tools - Without production fixtures - Without grinding wheels - 5-axis robotic automation optional - Comprehensive documentation available Availability: - Inspection by appointment - Available from 06/2026 Sales information: - Sale as seen and inspected - Warranty excluded

Condition: new, Year of construction: 2026, Robotic gantry system for metal sheet and profile cutting 3D robotic gantry system for plasma and oxy-fuel cutting has double-side drive, precise positioning system by racks and pinions on the 3 linear axes with exceptional speed and dynamics. Zero-backlash on the 3 rotational axes allow 4-side machine processing of profiles and round tubes. Precise gearboxes with minimum backlash, dynamical engagement of the motors to the racks, and rigid guide system allows smooth movement, excellent cut quality of corners and small holes. The gantry system has a cantilevered part crossbeam, which allows profile cutting in a cabin especially designed for this purpose. Transversal motion range (Y axis) -- on request Longitudinal motion range (X axis) -- on request Vertical motion range (Z axis) -- 1500 mm Beams and profiles types: T, L, H, U, rectangular tube, round tube Maximum dimensions of beams: Width up to 1200mm Rectangular tubes: Cross-section up to 600x600mm KEY FEATURES ▪ Stable metal construction with precise linear guides and servo-drives with racks and pinions on all axes; ▪ High dynamics, on all X, Y and Z axes: up to 30 m / min speed and acceleration up to 3 m / s²; ▪ 3D control on seven axes allows for a higher level of CNC programming; ▪ Maximum use of machine resources, thanks to the concept of combined processing of sheets and profiles - the ability to 100% load the machine when switching between sheets and profiles, without downtime for loading sheets and profiles and unloading cut parts ▲ PLASMA CUTTING EQUIPMENT HYPERTHERM -- on request Fpodpfx Aash I Nw Djlog ▲ INSTALLATION AND TRAINING INCLUDED Approximate installation and training period - 15 days