WEBER NE5 with 2 Co-Extr. WEBER ZE30

WEBER NE5 - ZE 30-ZE 30

Condition: as good as new (ex-display), Year of construction: 2023, The ENR series are air-cooled chillers for industrial use for outdoor installation. The ENR 038 has axial fans, scroll compressors, condensers with finned aluminum fins and self-cleaning coaxial evaporator for maximum reliability. Internal pump, tank, fan control, low GWP refrigerant R454B. Refrigerating capacity 37 Kw, envious GWP refrigerant R454B Gjdpfx Aofmd Hhegbsbg We have a lot of chillers directly from stock available used and new . contact us for a no obligation quote. We rent / sell / and also take over the service for all refrigeration systems Germany-wide.

Condition: reconditioned (used), Stock - No.: 2553 1 used, partly overhauled and functionally tested Single-Screw Extruder, equipped with: Material hopper loader Extruder BATTENFELD Typ UNI-EX 1-75-25 B Screw - Ø 75 mm – 25 L/D, Cylinder Air-cooled Extruder-Motor 120 kW – DC ( overhauled ) Screw –speed up to 130 r.p.m. additional Temperature controllers for down-stream equipment Control-Board with melt-pressure sensor / Display. Inspectiuon visist / trial-run shortly by appointment in our workshop Wuppertal Germany possible. We can offer, installed to this extruder: > screen-pack-changer > pelletizing ( strand, hot-face or waterring ) > other equipment Gjdpfx Aeiyyndsgbjbg Send us your inquiry. More extruder and complete pelletizing lines ex our workshop Wuppertal, send us your inquiry or visit us, you´re welcome

Condition: excellent (used), Year of construction: 2000, machine/vehicle number: 403, THERMO FORMING MACHINE TFT IMC 5030 (WITH TOOLS) Equipment / Additional information: unwinding: Roll recording: easy Max roll diameter: mm 1000 Settlement: automatically Thermoforming machine: Maximum tool dimensions: mm 520x330 Pos. Molding height max .: 15 mm Neg. Molding height max .: 120 mm Sheet width: mm 150/760 Movement Step: mm 50/330 Max HIPS film thickness: 1.8 mm Hub of the sub-table: 150 mm Clamping force: 7500 Kg Inst power top heater: 18.8 Kw Inst power under heater: 14.1 Kw Idle clock speed: per minute 40th power main drive motor: 2.2 Kw Engine power. Film feed: 0.75 Kw Air operating pressure: Kg / cm2 7 Water consumption at 12 °: 1t / 1` approx.30 Air consump. at 7 kg / cm2: 1t / cycle 125 Installed power: Kw 50 9xTool: Article no. // Tool no. // Cavities // Description / Product: 3599 // 457 // 10 // Vending machine cup capacity/capacity/contenance=223ml Gedpfx Asn D Ew Iogbjbg 593 // 460 // 8 // Coffee-to-go / thermo mug / thermo cup Filling capacity / Capacity / Contenance=300ml / 12 oz 509 // 452 // 6 // Ice cream cup: filled to the brim=140ml / Filling capacity with headspace 6mm: 120 ml 591 // 459 // 10 // Thermo mug ⌀ 81/180ml 740 // - // - // Standard cup with sealing edge ⌀ 75-120ml 3589 // 458 // 12 // Coffee-to-go / thermo mug / thermo cup: Filling capacity / Capacity / Contenance=80ml 595 // 456 // 10 // Vending cup / Gobelet pour automate: Filling capacity / Capacity / Contenance=150ml 210 // - // - // Baking case / technical part / plate or tray 8000 // 455 // - // Granule cup 180 ml / technical part with flat sealing edge

Condition: used, Year of construction: 1992, Overview This blowmoulder was built in 1992 from French manufacturer Sidel. It can produce up to 4.000 bottles per hour. Techn. Details Capacity: 4.000 bph 4 cavities Scope of delivery Blowmoulding machine | SIDEL | SBO 4/6 | 1992 Preform feeder Two types of molds for 1.5 L and 2.0 L bottles Cooling unit: RIEDEL Gedpfxsnpbhvo Agbobg

Condition: used, Coating system Hymmen CombiCoater ELX-S 1400 with UV dryer. * Technical data will follow shortly Gbedpelf H Tcsfx Agbjg * For self-dismantling and collection.

Condition: excellent (used), Desktop Metal 3D Printer Complete System Here we offer you Desktop Metal 3D printer complete system. Desktop Metal 3D printer studio system Complete system: 3D printer + debinding machine + sintering furnace Desktop Metal The three-part solution includes 3D printer, debinder and furnace Manufacturer Desktop Metal Model Desktop Metal Studio System Operating condition Used (Good) Year of manufacture 2019 Desktop Metal Studio System Includes: 1.1 Desktop Metal Studio 3D Printer Bound Metal Deposition (BMD) Technology. Features: Printed materials metal Technology FDM Use Industry Other features Office X-stroke 30 cm (12 in) Y-stroke 20 cm (8 in) Z-stroke 20 cm (8 in) Description: Unlike laser-based systems that selectively melt metal powders, the printer extrudes bonded metal rods - similar to an FDM printer. This eliminates the safety requirements often associated with metal 3D printing, Godpfok Hz Nqox Agbebg and it enables new features such as the use of closed-cell fills for lightweight strengths. 1.2 Desktop Metal Studio debinder (delamination machine) fully automatic debinding Cleaning tank: 17.4 L (in process) / 22.5 L (stock) Description: The debinder prepares green parts for sintering by dissolving the primary binder. With a low emission design, it requires no external ventilation and is safe for an office environment. Automatic liquid distillation and recycling means no need to refill between cycles. 1.3 Desktop Metal Studio Sintering Furnace hybrid technology (microwaves & conventional heating elements) Installation space 305x205x205mm Carbon housing Gas supply: 2 x 900 L gas cylinders Heating power: 20 kW Features: Function Sinter Configuration Chamber Heat source gas Other features High temperature, automatic Maximum temperature 1,400 °C (2,552 °F) Description: Fully automated and sized to fit through an office door, the furnace delivers industrial-grade sintering in an office-friendly package. Built-in temperature profiles matched to each design and material provide uniform heating and cooling without the residual stresses associated with laser-based systems. Condition: used / used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: used, Year of construction: 2008, clamping force: 160 kN, displacement volume: 251 cm³, injection pressure: 2,500 bar, overall weight: 8,200 kg, load hours: 37,200 h, screw conveyor diameter: 40 mm, terms of delivery: FCA Pegnitz delivery time: on request terms of payment: 100% prior to delivery Gbedpfx Agjwd Udlobog

Year of construction: 2013, operating hours: 960 h, condition: used, machine/vehicle number: Technical name AVN2000AB-2525PR-078250, Please check the below attached pdf. document for the full detailed description of the machine. For additional fotos and information please don't hesitate to contact us. Gbsdpfx Aslkdl Aegbjg Purchase 1 AVN2000AB Tunnelling Machine Mixed Ground Cutting Wheel The mixed ground cutting wheel is designed for AVN2000AB in mixed ground such as: mixture of soft ground, gravel or coarse gravel, weathered/soft rock. Supplied with soft ground cutting tools & disc cutters. Full set of cutting tools bolts and cutting wheel bolts included. Maximum Unconfined Compressive Strength (UCS ) 60 MPa Closed face type Cutting diameter 2 575 mm Cutting tools Chisel 12 No Chisel width 100 mm Scraper 8 No Cutting disc 11 No Cutting disc diameter 305 mm Tooling system backloading Machine AVN2000AB Articulated shield with face support / excavated material transportation by slurry. Slurry feed by 6 nozzles into crusher / excavation chamber and 2 nozzles to area around slurry discharge pipe. All nozzles (crusher/excavation) are equipped with interchangeable nozzles inserts for different nozzle diameters to run in medium pressure mode. Integral conical stone crusher behind cutting wheel. Face access for cutter inspection / change. Optional easily fitted cutting wheels for soft ground, mixed soil conditions with some rock and full rock conditions. Central drive unit with splinted shaft for reliable, heavy duty torque transmission to cutting wheel.

Condition: used, Year of construction: 2014, power capacity 3 kW feed pressure 7 bar liter capacity / l weight 286 kg Chicago Pneumatic CPVR15 CE screw compressor - Year of manufacture 2014 The CPVR15 CE impresses with its robust design, long service life and low operating costs. Whether in workshops, workshops or industrial applications - this compressor reliably supplies you with the compressed air you need. Drive power: 3 kW Delivery pressure: 7 bar Air output: up to 58 CFM (approx. 1,640 l/min) at 7 bar Weight: 286 kg Dimensions: approx. 965 mm (L) × 620 mm (W) × 1,040 mm (H) Operating noise: approx. 50-58 dB(A) Voltage/frequency: 415 V / 50 Hz Application: Workshops, craft businesses, industrial applications with medium compressed air requirements Included in delivery: 1x compressor - Chicago Pneumatic CPVR15 CE 1x refrigeration dryer - OMI ESD 108 - 0.70kW Gsdpfx Aoh A Sfdsgbsbg 1x Beko Öwamat 2 - oil-water separator Technical data was taken from publicly available sources

Condition: good (used), Robot Gbsdpfebrhtdsx Agbjg Manfacturer: Staeubli Type: RX170