Center lathe

SARO SPS 1250x9000

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, sheet thickness (max.): 60 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), Equipment: cone bending device, documentation/manual, 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls 570 / 500 / 430 mm Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Fodpfxjzbqquj Akysgh Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1999, functionality: fully functional, turning length: 3,000 mm, turning diameter: 1,000 mm, spindle bore: 197 mm, Upon request, videos of the machine in operation can also be provided. Maximum turning length: 6000 mm Turning diameter: over cross slide: 1000 mm Fgjdpsyr N N Refx Akyeh over bed: 1250 mm Spindle bore: 197 mm Spindle speeds: 0 – 665 rpm Faceplate diameter: 1200 mm Workpiece weight: 15000 kg between centers Motor power: 55 kW / 74 hp 3 gear stages: 1.5-55 / 50-180 / 180-665 rpm Accessories: Sauter 4-position tool turret (rotation defective) Tailstock (hydraulics partially defective, pressure loss) Chip conveyor 2 chip guard doors (incl. safety device) 4-way bed machine (flat bed) LED lighting

Condition: excellent (used), Year of construction: 2004, winch inkl. lifting capacity max. 2t. auf 2,7 Meter lifting capacity max. 1 Tonne auf 5,3 Mete Number of working hours 270 h Fgodpfx Akoq N E U Ajysh electrical ja

Condition: good (used), Flat-jaw thread rolling machine, thread rolling machine, segment thread rolling machine, cold forming machine, knurling machine, thread rolling machine -Manufacturer: EWM, flat jaw thread rolling machine knurling machine -Type: unfortunately without type designation -Drive: 4.6/5.8 kW 1435/2890 rpm -Belt drive: 3-way adjustable -Knurling plate: RAA 1.0 -Central lubrication: -Dimensions: 1680/920/H1440 mm -Weight: 1308 kg Fgsdsi Eg Nkopfx Akyoh

Condition: used, Used Trumpf 5axis laser for sale / 3d laser for sale Used Trumpf 5axis laser for sale / 3d laser for sale Trumpf TLC Cut 5 Year 2006 Fully serviced twice a year by Trumpf Uk Last service January 2019 New vacuum pump fitted – 28/05/19 Hours: Beam on: 14,922 hours Laser on: 59,480 hours Fedpfxjfuah Nj Akyegh 3.2kw Fully serviced. Jigs / cutting beds included. Delivery and installation can be arranged.

Condition: excellent (used), functionality: fully functional, turning diameter over cross slide: 580 mm, spindle bore: 104 mm, turning diameter: 870 mm, turning diameter over bed slide: 1,150 mm, Geminis GE 870 S lathe, with a 4000mm center distance, featuring a complete cast iron bed, dimension display, 870mm swing over the bed, automatic feed on the carriage, rapid traverse on the slides, a quick-change tool turret, 580mm swing over the cross slide, 1100mm swing over the tailstock, 340mm tailstock length, and speeds ranging from 16-1250 rpm. The spindle bore diameter is 104mm. It is equipped with a 3-jaw chuck with a 400mm diameter and a quick-centering mechanism, as well as a 4-jaw independent chuck with an 800mm diameter. It also includes 2 fixed steady rests and an additional universal 3-jaw chuck with a 315mm diameter. The main motor has a power rating of 18.5 kW. Overall, the lathe is in very good condition. Fodjzmp Hkspfx Akyegh

Condition: excellent (used), functionality: fully functional, Year of construction: 2000, machine/vehicle number: 3roll 3500x140 mm prepinch, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: MG, controller model: MG, number of rollers: 3, roller (bottom) diameter: 880 mm, roller (top) diameter: 950 mm, side roll diameter: 880 mm, roller length: 3,550 mm, working width: 3,500 mm, working height: 3,950 mm, sheet thickness (max.): 140 mm, sheet thickness steel (max.): 175 mm, overall weight: 200,000 kg, total length: 8,800 mm, total width: 5,100 mm, total height: 5,775 mm, power: 200 kW (271.92 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, Hydraulic Plate Bending machine planetary pinch pyramid with prebend. model MG35140V 3 roll capacity 3500x140 mm The machine was overhauled in 2024, Capacity : Plate width mm. 3500 Plate thickness mm. 140 Capacity chart in enclosed Tech data: -3 rolls driven hydraulic motorized with axial gear unit on each roll independent -Synchronized hydraulic rotation of the 3 rolls with variable speed. -Planetary design with pre-pinch fully hydraulic -Conical plate bending with hardened contrast pad -Digital position readouts of the bending rolls -Rolls installed on bearings double crown heavy duty -Overload safety hydraulic operation protection of the 3 rolls Fgjdpfxjyzim As Akyjh -High pressure hydraulic power pack with multi-pumps oil feed -Centralized control panel electric on wheels with joysticks and digital readouts -Emergency stop with safety system around the machine working area Rolls surface length mm. 3550 Top roll mm. 950 Side rolls mm. 880 Electric power on hydraulic unit Hp 100 + Hp 100 Voltage 380 Vac / 50 Hz Configuration & accessories installed with the machine -Hardened surface of the 3 rolls -Conical plate bending attachment , rolls tilt with contrast roller type. -Centralized operator panel with directional joysticks electric. -Digital position readout of the bending rolls. -Emergency and safety installations, certified CE -User manuals and instruction books in English -Dimension see layout drw in enclosed

Condition: used, Year of construction: 2009, faceplate diameter 3000 mm swing diameter 3500 mm turning height 3200 mm Control Fanuc type Series 320i Model A slide adjustment 1750 mm ram head dimension 300x300 mm x-axis 2700 mm Table load 30000 kg main drive motor 100 kW Tool changer 16 weight of the machine ca. 89 t dimensions of the machine ca. 8,5x6x8 m Fjdpeyqu Rwofx Akyjgh No. 1104 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: excellent (used), travel distance X-axis: 1,500 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 750 mm, table width: 1,500 mm, table length: 850 mm, rotational speed (max.): 2,500 rpm, quill stroke: 120 mm, SHW UF 5 Travels - X-axis (rotary table): 1,500 mm - Y-axis (vertical headstock): 1,000 mm - Z-axis (horizontal headstock): 750 mm Control system - CNC control: Heidenhain TNC 355 Automatic swivel head (change between horizontal and vertical machining) Quill 120mm Milling spindle holder SK 50 Speed 2500 rpm Fodpfovfm I Tsx Akyegh Partial overhaul 2014 - Year of construction 1990 - Inspection/repair 2025 Table assembly - Travel distance: X = 1,500 mm - Clamping surface: 1,500 x 800 mm Chip conveyor Splash guard cabin We have ALL spare parts for this series (SHW UF 5) in stock! About us: MBM Maschinenservice & Gebrauchtmaschinen GmbH is an independent specialist for SHW machine tools. Our main focus is in the field of tool milling machines. Our services include spare parts deliveries, on-site customer service, machine overhauls and control system modernizations. Services: - Used machines - Spare parts - Customer service - Machine service - Machine overhauls - Control modernization _____ Used machine - used milling machine - used bed type milling machine - orthogonal milling head - metalworking - tool milling machine - milling head - SHW machine - SHW spare parts - milling machine used - milling machine used - CNC milling machine used - drilling milling machine used - milling machine metal used - metal milling machine used - metal milling machine used metal milling machine used - used cnc milling machine - cnc milling machines - cnc milling machines - milling machine - large part machining - large part machining - large part machining - cnc large part machining - milling - shw - uf5 - uf 5 - Uniforce - SHW UF - SHW Uniforce - SHW Uniforce 5 - UFZ 5 - UFZ5L - UFZ 5 L - MBM Milling Machine - MBM Machine

Condition: good (used), functionality: fully functional, lifting height: 10 mm, load capacity: 25,000 kg, For sale: Components for hoist P1600 / P2000 Main hoist motor 36/20 K6P P1600/P2000 Fine Gear FG36 Hoist gearbox P1600 / P2000 P2000 housing H20 P1600/ P2000 rope drum H20 P2000 bottom block 4/1, 25t, 20mm rope P2000 rope guide Traverse / sheave - rope pulley All parts in TOP condition Load capacity 25,000 kg / 25 t. Hoist motor 36/20 K6P Fine gear FG 36 20 hoists available for sale 2-stage trolley travel Fsdsv Uvftopfx Akyegh Fully functional Well below OEM list price