Plate Bending Machine - 3 Rolls

NOSSTEC 8266 15/40

Condition: excellent (used), 3-Roll Plate Bending Machine / Round Bending Machine Manufacturer: Nosstec, Sweden Type: 8266 15/40 Year of manufacture: 1998 Serial number: 3058 Working width: 1,540 mm Hjdpfx Agoz Agn Dstjnt Plate thickness: up to approx. 4 mm Rollers: 3 pieces, steel rollers Drive: motorized Operation: electric control with foot switch and mechanical hand adjustment Weight: approx. 840 kg Documentation included Very good condition, fully functional.

Condition: new, Ostas 4-roll round bending machine 4R OHS 2070 x 220 Hydraulic side roller infeed Hydraulic folding bearing Hardened rolls Hnsdpfstvn D Tox Agtjt Conical bending device Separate control panel Roller length : 2000 mm Top roller diameter : 220 mm Side roller diameter : 180 mm Total motor power : 4+3 KW Weight : 4900 kg Dimensions (mm) : 4050 x 1550 x 1470 (L x W x H) Performance data bending: 11 mm with smallest inner diameter (5 x top roll) 9 mm with smallest inner diameter (1.5 x top roller) Bending performance data: 9 mm with smallest inside diameter ( 5 x top roller ) 7 mm for the smallest inside diameter (1.5 x top roller) All bending capacities are calculated on the basis of 250 N/mm2 yield strength Material ( ST 37 - ST 42 structural steel ) Special accessories installed: Infinitely variable rolling speed: NC control:

Year of construction: 2010, condition: ready for operation (used), Electrode force: 100daN, welding capacity: 255kVA, nominal input: 80kVA, with Cooling System DALEX DRF 5.2. Hnodpfxsiknv Eo Agtot

Year of construction: 2024, condition: new, Motorized sheet metal shear Technical data Cutting capacity: 2.5 mm Cutting length: 2550 mm Cutting angle: 1°40′ Stroke rate/min: 35 1/sec Motor power: 3 kW Back gauge range: 550 mm Table width: 400 mm Hnedpfx Agshk Nf Retjt Table height: 850 mm Height: 1260 mm Width: 1350 mm Length: 3100 mm Weight approx.: 1540 kg

Condition: new, Year of construction: 2025, Maintenance-friendly dedusting system specially developed for aggressive sandblasting dusts with pre-chamber impact separator, complete essentially consisting of: a) 1 cartridge dry filter, type PF 2.16.B250 for 30,000m³/h (other sizes available) Hedpjdrtalsfx Agtjnt each consisting of a stable, vacuum-tight 3 mm sheet steel housing, divided into the raw gas chamber with filter cartridges, filter pre-chamber impact separator and clean gas chamber with filter cleaning by means of compressed air, each with separate Easy Open maintenance door. Dust collection hopper with slotted valve or rotary valve for dust disposal using big bags. Solenoid valve control with differential pressure display for optimum adjustment of filter cartridge cleaning. Maintenance doors as swing doors Maintenance easy.

Condition: ready for operation (used), Year of construction: 1998, pressure 85.0 t chamfer lenght 2050 mm distance between columns 1750 mm column arm 410 mm stroke 365 mm dayligth 535 mm ajustment speed 200 mm/sec working feed 1.0 - 10.0 mm/sec return speed 135 mm/sec back stop - adjustable max. 600 mm table width 120 mm work height max. 1050 mm Number of working hours 28.500 h oil volume 200 l operating pressure 340 bar total power requirement 14.0 kVA weight of the machine ca. 9050 kg range L-W-H 2680 x 2100 x 2885 mm with increased installation height / piston stroke very well maintained condition (!!) with only approx. 28.500 operating hours - in checked condition - machine video - ?v=ZuwyPKJSYLw Equipment: - CNC electro-hydraulic press brake - including DELEM CNC control * swiveling control panel at the front left - CNC controlled axes: Y1 - Y2 - X - R - Z1 - Z2 - I + CNC crowning - CNC electro-motorized back stop (X axis) - CNC electro-motorized height adjustment of the back stop (R axis) - CNC electro-motorized adjustment of the stop fingers (Z axes) - CNC pneumatic die displacement (I axis) - CNC motorized table crowning Hjdoxaa Uropfx Agtont - WILA electro-hydraulic upper tool clamping - WILA electro-hydraulic Lower tool clamp - 1x freely movable 2-hand / foot control - 2x front, stable support arms including "sliding system" - side protective device (swinging doors) - rear protective device (swinging doors) - bending tool storage cabinet (right front, side) - original operating instructions + circuit diagram etc. further technical data: - feed speed X axis .. 500 mm/sec. - feed speed R axis .. 300 mm/sec. - feed speed Z axis .. 1000 mm/sec. - travel range X axis .. max. 600 mm - travel range R axis .. max. 250 mm

Condition: excellent (used), Year of construction: 2018, Geared motor, electric motor, electric geared motor, spur geared motor -Manufacturer: SEW-Eurodrive, helical gearmotor -Type: R97/II2GD EDRN160L4/3GD/TZF/AL i18.24 -Speed: 1474/81 rpm at 50 Hz, see photo type plates -Power: 15 kW -Shaft: Ø 60 x 120 mm -Protection class: IP54 -Dimensions: 970/400/H370 mm Hedpfxet Drkyo Agtont -Weight: 231 kg

Condition: new, Year of construction: 2026, -Tfon Leveltech® S-3513 Leveling Machine. -The Tfon Leveltech® S-3513 is a precision leveling machine optimized for ultra-thin materials, combining advanced electromechanical controls with easy operation for consistent, high-quality flattening results. -Key Specifications: Material Thickness: 0 – 0.3 mm. Hedpfskyrzlex Agtent -Maximum Material Width: 1.300 mm Minimum Material Length: 70 mm Quick Change System for Straightening Rollers: Standard. Flattening Gap Adjustment: Electromechanical / PC Controlled. Machine Dimensions (L × W × H): 2,685 × 1,585 × 1,820 mm. Total Weight: 5.000 kg.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. Hedjfz U S Eepfx Agtont The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2019, condition: new, Recirculating air convection furnace Gas-fired furnace CGN Powder coating oven NEW – SGS-800/O Gema Optiflex Hjdocw Tzxopfx Agtjnt Width: 2500 mm, Height: 2500 mm, Depth: 12500 mm Directly from the manufacturer. For more information, visit Romer-Deutschland.