Used Weinig Profimat 26 Super for sale (536)

Condition: used, Weinig Unimat 23 Technical data Working width 30 - 230 mm working height 19 - 200 mm elevated on pedestal u- re-li-o-u.o Hjdpfoncc Igex Ag Ejfn without feeder only machine machine is dismantled, immediately available Transport can be organized

Year of construction: 2000, condition: excellent (used), Weinig High-Mech A4 bundling system Hedpfxeq Rvrbs Ag Eefn Bundle forming packaging unit possible to combine with other Weinig outfeed handling systems available from stock such as buffers and stackers. Consisting of 1. Weinig 815-300 high speed bundling unit 2. Weinig 812-200 outfeed roller conveyor with crossfeed 3. Control panel with Siemens S7-300 CPU

Condition: as good as new (ex-display), Please check in your junk mail if you do not receive a reply within 24hrs from sending your inquiry !!! CAN SHARPEN MAX 406MM DIAMETER CUTTERS !!! The G-716 Semi-automatic Cutterhead Grinder is used to sharpen 178mm to 406mm diameter eased edge, milled to pattern, and fingerjoint cutterheads. Worktable traversing is automatic and has adjustable stops. Cutterhead indexing is manual. Each knife is held against a positive stop while being ground !!! No Index Plate To Change No index plate to change when working with heads with different numbers of knives. The use of an index plate assumes that the knives and head separations are uniform throughout, which is often not the case. If the height of the knife is high or low, then the front face of the knife will vary from knife to knife making the task of grinding difficult. The one constant is the back face of the knife, therefore the use of an indexing stop against the back face will provide for accurate indexing regardless of the irregularities in the knives and head slots. Head Indexing and Wheel Feed: Manual Minimum / Maximum Diameter Cutterhead: 7″ Min./16″Max. 178mm Min./ 406mm Max. Worktable Feed: Air / Oil Travel (maximum): 12″ 305mm. Adjustable Limits: Proximity Switch Speed: Fully Adjustable Index Method: Manual index after each knife is ground. Grinding Spindle: 1-1/2 HP Wash Down Duty TEFC Motor 3600 RPM, Dual ABEC 7 Precision Bearings, with Sealed Lubrication. 8″ (203mm)Diameter Grinding Wheel (9″ 229mm Diameter Max.) Coolant System: 15 Gallon Tank with Casters, Sediment Tray Full View Sight Glass, 5 GPM Pump (120VAC) Wash Down Hose Included Hjdpjq Dzi Tsfx Ag Ejfn Specifications Grinds 7″ to 16″ diameter eased edge, milled to pattern, and finger joint heads Automatic traversing worktable with adjustable travel limits Manual indexing of knives against a positive stop with grinding position pneumatic brake allowing precision indexing without the need of an index plate High precision 1-1/2 HP grinding spindle with sealed lubrication Recirculating adjustable flow flooded coolant system with wash down hose Fully enclosed grinding chamber with viewing windows and task light Grinding wheel feed allows unattended operation. New Proscale.

Condition: ready for operation (used), Year of construction: 1990, functionality: fully functional, operating hours: 4,452 h, cutting height (max.): 120 mm, cutting depth: 340 mm, main saw diameter: 380 mm, Raimann KR 310 E 340/120 multi-saw with movable disc - manufactured in Germany - year of manufacture 1990 - DTR - number of hours 4452 h TECHNICAL PARAMETERS: - track width 340 mm Hfjdpfx Agorhig Es Ejn - cutting height max 120 mm - cutting height with movable disc 85 mm - engine power 30 kW - minimum length of the element 700 mm - width of table 740 mm - feed regulated on inverter 6-48 m/min - three rows of pawls - possibility to mount a bush - sleeve diameter 80 mm - length of fixed sleeve 190 mm - electrical adjustment of cutting height - electrical adjustment of shaft height - four top pressure rollers - automatic central lubrication - laser - ruler - spigot diameter 250 mm Overall dimensions of the machine 250x200x220 cm weight 2000 kg

Year of construction: 2010, condition: good (used), Weinig GRECON TURBO S finger jointing line - German production - DTR, CE - year of manufacture 2010 - high efficiency up to 200 elements / min - 28 km / 8h TECHNICAL PARAMETERS: Wood parameters - width 60 - 225 mm - thickness 18 - 48 mm - length 300 - 2000 mm - pressing length 8100 - 16400 mm - power consumption 150 kW - air consumption 3100 Nl/min - suction capacity 14845 m3/h - two milling stations - undercutters - connecting with a dash and a zigzag - loading with a conveyor with spacers Hfsdsin Uulopfx Ag Eon - package width 600 mm - divided ironing length Folded machine dimensions - length 42000 mm - width 6000mm - height 2100 mm

Condition: excellent (used), Raimann KS 310 BV edger multisaw - year of manufacture 1995 - German production - DTR - two movable discs TECHNICAL PARAMETERS: - track width 340 mm Hfedjir Eubjpfx Ag Een - cutting height max 120 mm - engine power 30 kW - disc diameters 250/360 mm - Possibility to put on a shoe - electric height adjustment - feed continuously adjustable 11-38 m / min - power of the feed motor 1.5 kW - two movable discs - three lasers - max element width 1000 mm - minimum element length 600 mm with a shoe 400 mm - four upper pressure rollers - spindle diameter 65 mm - sleeve diameter 80 mm - spigot diameter 250 mm Dimensions 230x220x230 weight 2500 kg

Condition: excellent (used), Year of construction: 2005, Weinig Dimter OptiCut S 90 optimizer with 2 ejectors – after technical review – German production – year of manufacture 2005 TECHNICAL PARAMETERS: Hfedsi Apgmopfx Ag Ejn max. length of cut material 4500 mm max. width 360mm max. height 160mm automatic length measurement optimization in 4 quality classes total power 13 kW blade motor power 7. 5 kW pneumatic side and top pressure disc diameter max. 500mm OptiCom Assist control receiving conveyor 5600 mm two ejectors total length 13 m component marking printer cutting accuracy +/- 0.5 mm transport dimensions (length / width / height) 600 / 240 / 190 cm weight ~ 1800 kg

Condition: excellent (used), Year of construction: 2004, Weinig Dimter Opticut 200 Classic optimizer - after the technical review - year of production 2004 - declaration of conformity, DTR - German production Hedpogz Tbdofx Ag Ejfn TECHNICAL PARAMETERS: min./max. entry length of the element 800/3500 mm min./max. entry width of the element 80/200 mm min./max. element input thickness 12/80 mm type of wood hard / soft dash cutting wood classification max. feed speed 120 m / min acceleration 5 m / s saw blade diameter fi 500 mm saw hole diameter 30 mm saw spindle speed 4600 U / min duration of 1 cycle 0.7 - 1.2 sec a powered conveyor at the entrance and a marking station with side tables for two markers conveyor belt total power 15 kW length measurement - fluorescence camera for 3 qualities receiving station - conveyor belt full optimization total length 8300 mm stub diameter 80 and 120 mm OptiCom Direct control power supply 400 V / 50 Hz

Condition: used, Twin band saw Raimann B110 Duo Roll diameter 1100 mm Roll width 100 mm Hsdpfx Aodfc Shjg Ejfn Feed rate 0-40 m/min

Condition: good (used), Raimann K12 Multi-blade saw Hfodpfx Agjd Scdqe Esn Chain with spike Chain width 430mm Cutting height approx. 120mm Includes various accessories.

Condition: excellent (used), Weinig LTB250/3500G belt lifter Length 3500mm Width 250mm Speed 22m/min Hodpeu Eclrofx Ag Eefn

Condition: excellent (used), High speed moulder infeed comprising a freestanding flat magazine in front of a high speed moulder. The infeed magazine is driven by hydraulic motors powered by an 5.5kW hydraulic unit (max 140m/min). A buffer of feedstock is alligned laying flat side by side on the chain cross feeder. The chain feeder transports parts across to the fence. The part next to the fence is detected by a light beam and the the first roller is raised to allow entry and the transport roller then pushes the workpiece under the feed rollers of the planer. The first feed roller of the planer needs to be freewheeling roller to allow operation of the EM814. Hedpfewgbxzox Ag Esfn

Condition: used, Year of construction: 1969, Used machine Year of manufacture: 1969 Runs perfectly Hfjdpfx Agoxavtqo Eon Max. working width: 170 mm Max. working height: 130 mm 1st shaft: bottom 2nd shaft: right 3rd shaft: left 4th shaft: right 5th shaft: top Availability: short-term Storage location: Röllbach

Condition: excellent (used), Compact High Speed Planing Line Mechanisation with Stacker 1. Weinig EM814 moulder infeed with flat chain feeder 2. Weinig 820 high speed right angle moulder outfeed with cross feed sweepers 3. Weinig 811 board stacker with scissors lift (chain feed discharge options) -Boards are automatically transported laterally with the Weinig 820 right angle transfer. -Boards automatically form a layer and are then placed on the lifting table of the chain conveyor -The completed pack is transferred to the following chain conveyor -Maximum output: 40 cycles/minute for stacker (over 150m/min based on average length boards). -Space required: Length approx. 8000 mm, Width approx. 5000 mm approximately Hfjdpfxsxb U Txs Ag Esn -Pack size max 6100mm x 1200mm x 1200mm(high) 3. Weinig cross chains after scissors lift to move full packs away from the stacker when full. Possible to supply with Weinig Hydromat moulders 100m/min as needed.

Condition: used, Year of construction: 2007, machine/vehicle number: MR007003, For sale: A very complete Weinig Powermat 500 (year of construction 2007). Thanks to the increased planing capacity (300x160mm) and extensive mechanization, this is the ideal production line for professional woodworkers, carpentry workshops, or timber frame construction companies. Installation can be arranged upon consultation. Key specifications: - Large capacity: Maximum processing size of no less than 300 x 160 mm (ideal for heavy timber, joists, and wide parts). - Spindle arrangement (5 axes): Bottom (11 kW) – Right (7.5 kW) – Left (7.5 kW) – Top (11 kW) – Bottom (7.5 kW). - Including oscillating axis: Equipped with a moving spindle with an input measuring system. Enables efficient processing of boards with varying/tapering widths with minimal wood loss. - Combined spindle mounting: Equipped with a PowerLock quick-change system on both bottom spindles and the top spindle. Conventional mounting ø 40 mm side spindles. - PowerCom Control: Graphic touchscreen for quick profile changes and digital management of tool settings. Hjdpfxszwv Euo Ag Ejfn - 1-Man Operation: Including automatic return system. - Including accessories: Supplied with straight planing heads (bottom jointing cutters) and an extra horizontal PowerLock axis. Machine manuals are available. Technical specifications: - Number of planing axes: 5 - Order of planing axes: B-R-L-B-B - Maximum planing width: 300 mm - Maximum planing height: 160 mm - Feed rate: 5-30 /min - Serial number: 109200

Condition: excellent (used), Year of construction: 2009, LEADERMAC SPEEDMAC 923SP SPINDLES: 9 X 50MM X 6000 RPM BOTTOM (11 KW) - OUTBOARD BEARING RIGHT (11 KW) - LEFT (11 KW) - RIGHT (11 KW) - PROFILE JOINTER LEFT (11 KW) - PROFILE JOINTER Hjdpfx Agszv S Dde Eefn TOP (15 KW) - OUTBOARD BEARING BOTTOM (22 KW), TOP (15 KW) - OUTBOARD BEARING + STRAIGHT JOINTER BOTTOM (15 KW) - OUTBOARD BEARING + STRAIGHT JOINTER WORKING WIDTH: 230 MM, HEIGHT: 160 MM. MAX FEED SPEED 60M/MIN (POSSIBLE TO INCREASE IF NEEDED) STRAIGHT JOINTERS. PROFILE JOINTERS. CNC POSITIONING ON SPINDLES 3, 5, 6, 8 CONNECTION: 380 V / / 50 HZ 400 AMPS. FULL DOCUMENTATION INCLUDED.

Condition: used, Year of construction: 2008, WEINIG OptiControl 970090 tool measuring station, net price €7,650 Specifications: Tool diameter min. 90 Hfedpfx Aozvpw Ijg Ejn Tool diameter max. 300 mm Tool length 0 - 240 mm Radial measuring range (radius) 150 mm Non-contact measurement of tool dimensions, radius (R) and height (H), with display on electronic digital displays. Electronic digital displays providing information on tool radius and height. HSK63 tool holder for PowerLock tools. NEW: PowerLock adapter HSK63, shank D=50 x 260 mm.

Condition: used, Year of construction: 1997, Profiling line, consisting of DEP Gabbiani + Weinig planing machine DEP Manufacturer: Gabbiani Type: T-Module 80/1600 Year of manufacture: 1997 Planing machine Manufacturer: Weinig Type: 22 BL Year of manufacture: 1995 Technical data of the DEP - 6 machining motors per side - 2 fixed scoring units, 3.2 HP / 3000 + 4500 RPM - 2 chip-removing units: 12.5 HP / 3000 + 4500 RPM - 2 chip-removing units: 12.5 HP / 3000 + 4500 RPM - 2 slotting units: 12.5 HP / 3000 + 4500 RPM - 2 free spaces - 1 feed motor: 4 HP / 1400 RPM Angle transfer between DEP and planing machine - Length: 290 - 1600 mm (1800 mm) - Width: 18 - 150 mm - Thickness: 5.5 - 50 mm - Density: 600 kg/m³ - Output max.: 150 workpieces/min - Belt conveyor after the double-end profiler - Toothed belt conveyor with brush attachment as counter holder - Cam conveyor for singulation - Toothed belt conveyor as buffer section - Longitudinal discharge - Roller conveyor before the planing machine - Control: Vipa, compatible with Siemens S7 300 Hedjzuzfbspfx Ag Eefn - Safety technology Protective door switches: 3 Safety light barriers: 1 Technical data of the planing machine Working width and working height - Working width: 20 - 230 mm (with tool diameter 125 mm) - Working height: 9 - 140 mm (with tool diameter 125 mm) Infeed table - Length: 2000 mm - Adjustment range of the jointer table: 10 mm - Adjustment range of the fence: 10 mm Surfacing table - Length: 1200 mm - Adjustment range of the table: 10 mm - Adjustment range of the fence: 10 mm Jointer spindle - Motor power: 5.5 - 15 kW Thicknessing spindle - Motor power: 5.5 - 11 kW Left spindle - Motor power: 5.5 - 11 kW 2. Right spindle - Motor power: 5.5 - 11 kW Top spindle - Motor power: 5.5 - 22 kW Bottom spindle - Motor power: 5.5 - 22 kW Universal spindle - Motor power: 5.5 - 11 kW Feed - Cardan feed, continuously adjustable: approx. 6-36 m/min - Motor power: 4 - 8.6 kW Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Four-sided planing machine Manufacturer: Weinig Type: P 23 E Year of manufacture: 1998 Technical data - Working width: 230 mm - Working height: 8-120 mm - Number of spindles: 5 (top, right, left, bottom, top) - Spindle speed: 6000 rpm - Feed rate: 5-24 m/min - Total connected power: approx. 25 kW - Infeed table: approx. 2000 mm - Weight: approx. 2500 kg Hedjzuzfuspfx Ag Eefn Note: The technical data and descriptions are copies of the original order confirmation. The information provided is for informational purposes only and is not binding.

Condition: excellent (used), Year of construction: 2004, Weinig Hydro fine planing machine, Uniplan 23 Year of manufacture: 2004 Working width: 230 mm Working height: 120 mm 1st spindle, bottom: 7.5 kW Hfodpozg Euqsfx Ag Eon 2nd spindle, top: 7.5 kW

Condition: excellent (used), Year of construction: 2011, complete window production line WEINIG CONTUREX C 124 with universal drilling head Hfedszg T Hhspfx Ag Esn in very good condition year of manufacture: 2011

Condition: used, Weinig U22N Number of spindles: 8 Spindle diameter: 40 mm Spindle arrangement: Bottom Right Left Right Top Bottom Top Universal Hedpfozhk T Ujx Ag Esfn

Condition: used, Weinig Powerlock L=240 Z=2 head with rebate cutter below Type 536, diameter 93 mm 536.095.04 Centrolock reversible knife system Z2 Mounting: PowerLock HSK Length: 240 mm Price: 425 Euro Hfodpfjzdq Htox Ag Eon

Condition: ready for operation (used), Year of construction: 2015, Weinig Powermat 700 6x 40mm Spindles. CNC on spindles 3, 4 and 5. Width 20-230mm Height 10-160mm Memory system Hjdjztvhhepfx Ag Eofn Automatic lubrication system for bedplates. No 1.  11kW - Bottom 7000rpm No 2. 7.5kW - Right 7000rpm No 3. 7.5kW - Left 7000rpm No 4. 15kW - Top 7000rpm No 5 . 11kW - Top 7000rpm No 6 . 11kW - Bottom 7000rpm Electronically variable feed. 40m/min Short infeed table. Marathon coating for machine bed plates. Manuals & hand tools.

Condition: used, WEINIG motor / CNC drive as a used spare part for woodworking machines. Hodpfsztvtqjx Ag Ejfn