Used Turret Punch Press for sale (14,438)

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Ijdpjk S Htxjfx Aa Eoaw Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition

Condition: new, Year of construction: 2025, neu 2025 090185 prompt, Zwischenverkauf v Polen 7950 € 153.44 € 1 47 to 110 mm 27 mm 25x18 mm 8 s 16 mm 700 bar 479 mm 135 mm 388 mm 117 kg Ijdpfowirmbjx Aa Eoaw MOBILE HYDRAULICS-POWERSTATION Double action - fully automated process of punching and return Wide range of hole diameters up to 27mm Intelligent control system with inching and automatic load detection Mode indicator light Protection against accidental start-up OPTIONAL: Gantry punching station for increased productivity and operation comfort € 710,-

Condition: ready for operation (used), functionality: fully functional, FOR SALE: BRUDERER BSTA 60 High-Speed Stamping Press With Automatic Strip Feeder BBV 300/200 600 kN | 100–800 spm | Fully automatic | Top-tier Swiss quality Technical Highlights: Nominal force: 600 kN Stroke rate: 100–800 strokes per minute Max. feed length: 200 mm. Year: Unknown (No ID Plate) / Tested under power: 2025 Drive power: 30 Hp Control voltage: 24V AC Power connection: 440VAC / 50Hz Adjustable stroke: 20 / 25 / 31 / 38 / 45 /51 / 58 / 64 / 70 / 76 mm Shut/Ram height adjustment: 80 mm Working Dimensions: Max tool installation width: 620 mm Strip pass width: up to 320 mm Ram area: 800 × 500 mm Table area: 620 × 680 mm Max strip width: 300 mm Max feeding pitch: 200 mm Max material thickness: 6 mm Feeding angle: 180 Deg Machine Dimensions: Machine footprint (L × W × H): 2210 × 2075 × 2190 mm Weight (approx.): 8,000 kg Equipment Includes: Feeder BBV 300 – fully synchronized mechanical strip feeder system Integrated control cabinet Pneumatic clutch and brake Adjustable stroke and shut height Compressed air connection: 6–10 bar Oil cooling unit included Ready for integration with peripheral systems Machine in excellent technical and visual condition Fully tested Immediate availability from Europe Worldwide shipping available Iasdpfxsxz Ugxe Aa Eew Contact us today for pricing and further technical details. Let us help you upgrade your production line with Swiss precision engineering.

Condition: used, Die-cutting machine – Swivel frame die-cutting machine – Flatbed die-cutting machine – Toggle press – Eccentric press Die-cutting machine + feeder for use with strip-type die-cutting tools Flatbed die-cutting machine HELMERDING, type PSH 25 Item no. EP 97784, Machine no. 6073, Year of manufacture 1998 Pressing force 25 tons Distance between tie rods 700 mm Table area = installation space 800 x 670 mm Table area = installation frame, width 510 x depth 440 mm, plate thickness 20 mm Punch area 800 x 670 mm Through-hole in the table 490 x 420 mm Punch stroke 45 mm Punch adjustment distance 10 mm Installation height = tool height 100 mm Stroke rate up to 250 strokes/min Motor power 15 kW Mains connection 400 volts, 50 Hz - controlled drive for stepless stroke rate adjustment - pneumatic clutch-brake combination - punch equalizing cylinder - automatic central lubrication system VOGEL - massive base plate with 4 vibration damping elements under the machine Space requirement L x W x H approx. 3000 x 2000 x 3000 mm Weight 4.5 tons Good condition Previously, the machine was used for die-cutting cardboard sheets. Ijdpfx Asdzqmzsa Eoaw Ideal for die-cutting non-woven fabrics or similar materials for respiratory masks.

Condition: used, Pneumatic press, compressed air press BOSCH Type Manufacturer’s No. Year of manufacture 1980 Pressing force: 18 kN = 1.8 tons at 5 bar 15 kN = 1.5 tons at 4 bar 12 kN = 1.2 tons at 3 bar Iajdpfx Aeh U Dtusa Esw 8 kN = 0.8 tons at 2 bar 6 kN = 0.6 tons at 1.8 bar Overhang: 100 mm Ram stroke: 70 mm Table surface: 245 x 200 Ram surface: Ø 45 mm Maximum installation height: 235 mm Arbor hole: Ø 20 mm with clamping screw Compressed air requirement: 5 bar - Pressing force can be continuously adjusted via a pressure regulator - Pneumatic cylinder with ram, height adjustable by 90 mm - Pneumatic two-hand operation - Mounted on a metal frame with wooden plates Space requirement L x W x H: 1050 x 700 x 1600 mm Weight of pneumatic press: 82 kg Weight with table frame: 140 kg In good condition

Condition: used, Single-column – Eccentric press PELS - RICHTER, type PEKR 125 Machine no. 20684, year of manufacture 1967 Pressing force: 125 tons Reach: 430 mm Table size: 1100 x 750 mm Ram surface: 890 x 650 mm Table opening: Ø 400 mm Stroke adjustment: 6 to 115 mm Ram adjustment: 100 mm Installation height for maximum stroke at the top: max. 450 mm Arbor hole: Ø 50 mm Stroke rate: 60 strokes/min Table height above floor: 900 mm Motor power: 7.5 kW Power connection: 380 volts, 50 Hz - Overload protection by shear plate in the ram - Compressed air coupling-brake combination DESCH - Ram weight balancing cylinder - Manual ram adjustment - Two-hand operation Ijdpfefim Thsx Aa Eoaw - Cam indexing mechanism - Central grease lubrication system Vögele - Stroke counter Space requirement L x W x H: 2300 x 1450 x 3030 mm Weight: approx. 10 tons Good condition

Condition: ready for operation (used), pressure 30.0 t punching cross-cut in cmm 30.0 in 9.0 mm stroke ca. 35 Hub/min throat 610 mm stroke - stepless adjustable 0 - 28.0 mm oil volume 35.0 l work height max. 1010 mm total power requirement 4.0 kW weight of the machine ca. 1200 kg. range L-W-H 1400 x 700 x 1600 mm good condition (!!) with a lot of application tools (stamps/dies) Furnishing: - electro-hydraulic hole punch, with large throat - Material/sheet metal scrapers including scraper plates - Large material support table, with adjustable depth stops - continuous stroke adjustment - freely movable foot switch including protective cover - Forklift pockets for easy transport - side storage area - lots of accessories + tools - including tool cabinet - Matrix base (for special size matrices) Iaodpfx Aaexaaipj Eew - Stamp holders (for special size stamps) - original user manuel

Year of construction: 1997, condition: good (used), Used fully serviced and good condition Trumpf 500r cnc punch press for sale TRUMPF TRUMATIC T500R Large format rotation cnc punch press for sale Fully serviced Iodjhtfp Tspfx Aa Esaw Machine capable of taking multi tool Complete with tool holders and tools including multi tools Complete with Retractable clamps 3metre x 1.5metre sheet without reposition. Additional extras with the machine: Cabinet full of tooling Multitool Multiset – tool setter Quickload Quick sharp tool grinder Trumpf TC 500R Turret Punch 3000 X 1500mm large format machine 1600 throat x 3metre rail. TRUMPF TRUMATIC 500 CNC PUNCH WITH CONTROL & AIR TABLE CAPACITY: 220KN SERIAL YEAR: 1997

Year of construction: 2001, condition: excellent (used), Quality used Trumpf Trumatic 500R CNC Punch Press for sale A late Trumpf 500 just before the 5000r Iodpfx Ajh Nf Upsa Esaw 2.5metre x 1250mm sheet metal before reposition 1300mm throat New / Year 2001 Fully serviced With manuals Good condition and be seen working in production Complete with: · Capable of taking multi tool a good selection of tooling available along with multi tools

Year of construction: 2000, condition: excellent (used), very clean / low hours used Trumpf Trumatic 500R CNC Punch Press for sale 2.5metre x 1250mm sheet metal before reposition 1300mm throat Iodpfx Asng Al Aoa Eoaw New / Year 2000 Fully serviced With manuals Good condition and can be seen working in production Complete with:

Condition: used, Automatic High Quality Grinding Automatic High Quality Grinding Machine Type : Other All punch operators know the importance of tool maintenance on part quality and tool life. The AMADA TOGU is the solution; an automatic tool grinder design specifically for high quality grinding of sheet metal tooling. Unmanned operation Simple operator control Quick, reliable grinding of all standard tooling Supplied with jigs for shear angle grinding Restores tooling to optimum condition resulting in high quality parts Enables regular regrinding to maximise tool life USED AMADA AUTOMATIC TOOL GRINDER MODEL TOGU-III MACHINE SPECIFICATIONS Model ……………. TOGU-III Max. Diameter Tool Size ……………. 6.30 Max. Grinding …………… .039” Main Axis Motor …………… 2 H.P. 2 P Main Axis Rotation Speed ………….. 3000R.P.M. (60Hz) Main Axis Travel …………… 9.45” Main Axis Feed Motor …………….. DC Servo Motor (0.05 H.P.) Main Axis Feed Speed-High ………… 23.6 I.P.M. Ijdpfx Aasfuai Uj Eoaw Main Axis Feed Speed-Middle ………. 2.36 I.P.M. Main Axis Feed Speed-Low …………. 0.002 I.P.M. Table Motor ……………. 0.134 H.P. 4P Table Rotation Speed …………… 72 R.P.M. (60Hz) Cooling Water Pump Motor ………….. 0.08 H.P. 2P Cooling Water Pump Flow …………… 0.9 CFM (60 Hz) Machine Weight …………….. 1,058 lbs Power Supply …………….. AC220V 3 Phase 2.5 kVA (Transformer Used Outside 220v Area) Air Supply …………… 60 C.F.M. Grinding Wheel …………….. CBN 5.31 Benefits: Fast and Easy to Use Fully automated machine Unmanned grinding cycle Easy operation – load ᐳ inputᐳ start Programmable re-grind amount High Quality Finish Automatic feed of wheel prevents tool burn Automatic grinding wheel dress indication Excellent surface finish Safe Unique safety locking system ensures operator safety Visual operation/standby indication Coolant and Filtration System Automatic coolant application prevents tool burn High quality finish maintained by filtration of coolant liquid

Condition: ready for operation (used), Schüco tools, pressing tools, stamping tools, Art. No. 293900, 290146-02, 299259, 290146, 293338, 293902, 296198, 299905, 296168, 293901, 280162, 296548, 293354, 287568, 290146-02, 296170, 296159, 297755, 293807, 296199, 299372, 293899, 282028-04, 283072-02, 280222-05 and 5 pieces without a number. Iasdpfx Aod Sc D Ssa Eew

Condition: new, Year of construction: 2025, Sliding clip formers are used to produce fixation sliding clips for double standing seam roofing panels. Before installation roofing panels have to be made using roll former roofing machines. After finishing of panels production and preparing roofing works panels can be installed on roofing place with special fixation clips. Those clips, depending on design, could be fixed or sliding ones. Fixed clip has simple and cheap design so it can be good for small roofs that doesn’t have long length panels. Sliding clip are good for big roofs with different designs and long-length panels. Sliding clips can move and self-find perfect position so not be damaged and safe for roof while temperature expansions. We offer punching presses for making both fixed and sliding clips. We make sliding clip formers for 25, 27 or 39mm clip highs For sliding expansion clips productions there have three presses to be used. First sliding clip bottom part press is used for punching bottom part of sliding clip with fixation round holes and connection oval hole. At the same time this press cuts metal strip with necessary length. Blank for clip production is easy to get using manual guillotine or cut-to-length slitting machine. Iaodpfxsqxalxs Aa Esw Second sliding clip bottom part bender is used for bending of sliding clip bottom part to 90 degrees angle. So, after this operation bottom part is ready. Third clip former makes top part of sliding clip at the same time forming and bending it. After producing bottom and top part of sliding clip you can easily connect it to one working sliding clip. So using sliding clip formers that we offer you can easily make expansion clip and use it while double standing seam roofing installation without any unnecessary deformations. Maximum metal thickness you can work with -1mm. To get more information about sliding clip former we produce please contact our sales department.

Condition: good (used), Hoza EMU punch This machine is ideal for punching out small molded parts from paper, rubber or textile goods. It has a high pressing force and fits on any stable table. The cut is initiated via a two-hand safety control. Forged blades or steel rule blades can be used in the machine. Knife stroke: 30 mm Max. punching format: 150 x 100 mm Weight: approx. 150 kg Color: hammer blow blue Dimensions: 450 x 360 x 600 mm Further items in other sizes - new and used - can be found in our store! Iedpsuzhmtsfx Aa Eeaw International shipping costs on request!

Condition: used, functionality: fully functional, Year of construction: 2004, operating hours: 26,426 h, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, punching force: 20 t, The punching machine is in good condition and has always been serviced on time by certified Amada service representatives. All documentation is included. The drum encoder was recently replaced. Iajdpfx Ajw E Emaea Eew The machine is sold complete with software and tools. The punching machine is connected and can be tested on site. Specification: Year: 2004.07 Made in: France Operating hours: 26,426 Power-on hours: 65,006 Control unit: AMADA AMNC-F Punching force: 20 tons Stations: 45 Tools: sold with tooling Software: Linea 5 / Combi 5 (Only works with Windows XP) Sheet length: 2,500 mm Sheet width: 1,270 mm Sheet thickness: 3.2 mm Sheet repositioning: 5,000 mm Workpiece weight: 150 kg Dimensions: L 6080 x W 5120 x H 2318 mm Weight: 16,500 kg Location: Lithuania Test possible: Yes If you have further questions, we will be happy to answer them.

Condition: good (used), Pressing force: 25 t Cutting capacity: thickness / width: 1.25 / 140 mm Isdpfx Aasfim Dwo Eeaw Number of strokes per minute: min./max.: 250 strokes/min. Ram stroke - max.: 20 mm Usable table area: WxL: 440 x 360 mm

Condition: good (used), Table size: 350 x 350 mm. Isdpfx Aaofm A Amo Esaw

Condition: new, punching pressure 28.0 t punching cross-cut in cmm 31 in 7.0 mm ST throat 250 mm dayligth 223 mm no. of strokes 10 - 30 Hub/min oil volume 32.0 ltr. Isdpfx Aaew U U S No Eeaw work height max. 1033 mm total power requirement 3.0 kW weight of the machine ca. 553 kg dimensions of the machine ca. 730 x 540 x 1530 m Furnishing: - Punch quick-change device up to Ø 31 mm - green series - installed: round punch no. 5 Ø 25.0 mm and round die no. 3 Ø 25.7 mm - Free: LED lighting in the punching area - Swiveling scraper (plates exchangeable) - Various material support tables are available separately - Brace - 2-step foot switch, with double press for grain search function - electrical controls - Stroke length and stroke position continuously adjustable - integrated hydraulic unit with oil filling - Performance specifications apply to a material strength of 450 N/mm² - Main connection cable and plug for 16 amps are not included in the scope of delivery

Condition: used, Single-column eccentric press BERRENBERG Type EPtG 20-325 N-0 Mach. No. 15342, Year of manufacture 1974 Pressing force 20 tons Projection 320 mm Table surface 550 x 350 mm Through hole in table 190 x 120 mm Push surface 305 x 140 mm Table intermediate plate L x W x H 540 x 340 x 55 mm Through hole in table intermediate plate Ø 103 mm Clamping pin bore Ø 40 mm Stroke adjustment 8 - 70 mm Push adjustment 35 mm Installation height max. 345 mm (without table intermediate plate) Installation height max. 290 mm (with table intermediate plate) Table height above floor 700 - 750 mm (without table intermediate plate) Stroke rate 100 to 180 strokes/min. Drive power 1.5 kW Power supply 380 V, 50 Hz - Pneumatic clutch-brake combination, manufacturer: ORTLINGHAUS - Electric foot switch and two-hand operation - Stroke rate continuously adjustable via variator drive - Table height adjustment via threaded spindle approx. 150 mm - Manual central grease lubrication BEKA Schmiertechnik - Height-adjustable press table via threaded spindle - Electrical diagram Isdpfev Tp D Hsx Aa Eeaw Space requirement L x W x H 1600 x 850 x 1950 mm Weight 1250 kg Good condition

Condition: used, Single-column hydraulic press, straightening press, punching tool – ECKOLD Press frame with hydraulic cylinder, mobile press, punching unit Type RSD 1500 - 125 Machine No. 317 / 690 Year of manufacture approx. 1986 Pressing force 150 tons Stroke 125 mm Ram stroke 35 mm Table size 280 x 210 mm Ram surface Ø 125 mm Installation height (ram to table) max. 265 mm Table height above floor 403 mm Hydraulic operating pressure max. 500 bar - without hydraulic unit - Ram surface with 4 threaded holes M16 and 20 mm guide groove, with a centering bore Ø 15 mm in the center - 1 high-pressure hydraulic hose with external thread M30x1.5 mm, hose length 4 meters - 1 high-pressure hydraulic hose with union nut M30x1.5 mm, hose length 4 meters Space requirement L x W x H 700 x 300 x 1450 mm Weight 1250 kg Good condition Isdsd Swtaopfx Aa Eeaw

Condition: used, Single-column eccentric press KRUPP, type PEKRD 125 h Machine No. 2861, Year of manufacture 1977 Pressing force: 125 tons Reach: 400 mm Table size: 950 x 750 mm Ram area: 800 x 540 mm Table opening: 100 x 250 mm Stroke adjustment: 8 to 160 mm Ram adjustment: 100 mm Installation height for maximum stroke at the top: max. 550 mm Stroke rate: 60 strokes/min. Table height above floor: 800 mm Motor power: 10 kW Iaodpfx Aaedzqdde Eow Power connection: 380 volts, 50 Hz - Hydraulic overload protection in the ram - Pneumatic clutch and brake combination ORTLINGHAUS - Ram weight compensation cylinder - Motorized ram adjustment - Tabletop with ball bearings - Two-hand operation - Central lubrication system HELIOS - Stroke counter - UVV 7n 5.1 §4a, paragraph 2, No. 3b for manual feeding operations Space requirement L x W x H: 2300 x 1800 x 3200 mm Weight: approx. 10 tons Good condition (very little use)

Condition: good (used), Year of construction: 1998, Neat used punching machine from Euromac Iaodpfx Ajxld R Ioa Ejw Type CX 1000 30 Capacity 30 ton Unloading 1000mm Overwrap up to 10000mm Including drawer cabinet with lots of tooling and multitool

Condition: used, Year of construction: 1991, pressure 70.0 t punching cross-cut in cmm 27 in 20 mm punching cross-cut in cmm 32 in 14 mm work height max. 1060 mm column arm 500 mm weight of the machine ca. 1500 kg. total power requirement 7.0 kW range L-W-H 1550 x 1200 x 1950 mm good / well-maintained condition (!!) New price approx. 21.000 euros Special price on request Equipment: - electro-hydraulic hole punch, with large projection - large GEKA stop table with movable stop system - sheet metal stripper with stripper plates - stepless stroke adjustment - die base - 1x freely movable foot switch - operating instructions (PDF) Iaedsxabu Tjpfx Aa Eow

Condition: used, pressure 100 t punching cross-cut in cmm Ø 31 in 25 mm stroke 10 - 50 mm column arm 510 mm work height max. 1100 mm no. of strokes 14 - 45 Hub/min punch diameter max. Ø 90.0 mm oil volume 103 l total power requirement 7.5 kW weight of the machine ca. 2400 kg. range L-W-H 1750 x 1020 x 2050 mm maintained condition (!!) New price without accessories approx. 25.000 euros Special price on request Furnishing: - heavy / robust electro-hydraulic hole punch, with large throat - Punching station with material/sheet metal scraper - stepless stroke adjustment .. 10-50 mm - freely movable foot switch including protective cover - hydraulic low pressure finder for foot switch operation - Crane hanging eye for easy transport - side storage area Iaodpfxoxabrfj Aa Eow - Hydraulic unit, integrated - Three-phase motor, 400 volts, 50 Hz - original instruction manual

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2008, operating hours: 72,918 h, laser power: 2,700 W, punching force: 22 t, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 8 mm, sheet thickness aluminum (max.): 4 mm, TECHNICAL DETAILS Combined punching/laser operation: 2,585 x 1,650 mm Punching mode: 3,085 x 1,740 mm Laser operation: 3,085 x 1,650 mm Outputs Laser power: 140 - 2,700 W Maximum sheet thickness: 8 mm Cutting capacity for mild steel: 8 mm Cutting capacity for aluminum: 4 mm Cutting capacity for stainless steel: 6 mm Maximum punching force: 220 kN Active hold-down device (programmable in stages): 4.5 - 20 kN Maximum workpiece weight: 230 kg Speeds Maximum positioning speed X-axis: 90 m/min Y-axis: 60 m/min Simultaneous (X and Y): 108 m/min C-axis punching: 60 revolutions/min Thread forming: 180 revolutions/min Punching stroke sequence (E = 1): 900 1/min Marking: 2,800 1/min Tools Linear magazine: 18 tools with 3 clamps Tool change time: 1.5 - 5 s Tool accuracy Position deviation: ±0.10 mm Average position spread: ±0.03 mm Programmable slides for punched and laser parts (max.) Size: 500 x 500 mm TRUMPF CNC control: based on Siemens Sinumerik 840D Iedpjw Suwyefx Aa Eoaw MACHINE DETAILS Laser switch-on time: 72,918 h Cutting time: 18,536 h Space requirement (width x length): 7,900 x 9,100 mm Height: 2,400 mm Weight: 22,500 kg Laser gas consumption CO2 / N2 / He: 1 / 6 / 13 l/h Connected load: 73 kVA