Used Swivel Rotary Table for sale (47,950)

Condition: used, Technical details: Nsdpfx Aeu N D Sbsf Eswn table length: 2000 mm table width: 1700 mm table load: 15 t x-travel: längs=3000 mm table rotating: 360 motorisch ° height over floor: 1020 mm total power requirement: ca. 1,0 kw weight of the machine ca.: 14,2 t dimensions: 5,7x2,1x1,0 m The boring mill table was built in 1985 and overhauled in 2023 (retrofit) The table is mounted on a flat bed guide (5000x1380mm). The axis of rotation (B) is mounted hydrostatically, 9x T-slots according to DIN 650 and 508: a=28mm; h=54mm; b=51mm; c=21mm whose center distance = 160mm B-axis as positioning axis, which is clamped. *

Condition: used, Year of construction: 1991, Eye-level control panel, Aigner integral stop including feed with sliding carriage (without stop ruler), milling stop with digital display and swivel mechanism Storage location: Nattheim Nwedov Ai N Uspfx Af Ejn

Condition: new, table diameter 340 mm table load 160 horizontal kg. table load 100 vertikal kg. turning speeds 0,6 - 6,0 U/min swivelling range 0 - 90 Grad bore 60,0 mm motor 230 Volt weight of the machine ca. 56 kg. range L-W-H 385 x 340 x 375 mm Furnishing: - The table can be adjusted at an angle of 0 to 90 degrees tilt and jam - Start / stop via a location-independent foot switch. - Direction of rotation can be selected right / left. - Adjustable rotation time - The turntable has a 60 mm hollow shaft - The turntable has a diameter of 340 mm. The surface is chrome-plated for Protection against welding spatter. - The table speed is adjustable from 0.6 - 6 rpm. - The control of the welding machine via the turntable control is possible. - The ground contact transmits 300 A / 100%. - The turntable and the control are separate. - HF protected. - COM 1800 control with lap welding - Operating instructions in German Functions COM 1800 control: - Right/left rotation - Infinitely variable speed control - Welding torch on/off - Overlap welding adjustable - Controller for rotation time (2-stroke / 4-stroke) Nwodpfxjxabm Ne Af Een - Speed display

Condition: ready for operation (used), BELANGRIJKSTE KENMERKEN: Tafelafmetingen: 3000 x 3500 mm Omgeschreven cirkel: 4300 mm Toelaatbare belasting (gelijkmatig verdeeld): 50 ton op 3000 x 3500 mm Totale tafelhoogte zonder cilinder: 1.250 m Aantal T-gleuven, breedte 36 H7: 13 T-sleufafstand: 250 mm Lengteverplaatsing: 2700 mm Longitudinale voedingen / bed: • positionering: 2 mm/min • werkend: 1 tot 3000 mm/min • snel: 3000 mm/min Circulaire feeds: • werkend: 0,0006 tot 0,6 tpm • snel (50-tons belasting): 0,6 tpm Nominaal koppel van longitudinale motor/bed: 9,4 mkg Nominaal koppel van cirkelmotor/tafel: 22 mkg Totaal geïnstalleerd vermogen: 50 kVA Nwsdpfx Afsxpggyo Esn Tafelgewicht (zonder elektrische apparatuur): 31.000 kg

Condition: good (used), Year of construction: 2014, For sale are 2 identical injection molding machines of the company Netstal and the type SynErgy 2000-230/110 The machines were in production until the last day The company from which these machines originate attaches great importance to maintenance and servicing, which is why the machines are in very good condition 2 K function Turntable Designation Netsal SynErgy 2000 Clamping force in kN 2000 Machine drive power in kw 45 Year of construction 2014 Operating hours 20209 Weight 13300kg Length 6901mm Width 2075mm Height 2240mm plus 800mm flow box Cylinder size AG1 20mm Cylinder sizeAG2 16mm _____ Designation Flow Box Nsdpfxskwb Dis Af Ejwn Type LMP 105 Manufacturer Max Petek Serial number S 140743 Year of manufacture 2014 _____ Can be purchased additionally: Krauss - Maffei MH 50 robot Designation 6 -axis: Yaskawa Type: DX 100 Operating hours approx. 8900 Year of construction 2014 The systems can be purchased complete or in individual parts Prices plus value added tax Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: good (used), gebr. dividing head with a 3 jaw Röhm chuck dia 140 mm Nsdpfxeipic Ij Af Ejwn

Condition: used, Technical details: weight of the machine ca.: 4,0 t machine dimensions LxWxH: 1,8 x 1,8 x 0,9 m Machine table with 5 indexing tables for multi-side machining Application: Multi-side machining of workpieces in circular transfer machines in one operation on 5 indexing tables with clamping devices. Design: Round, fixed body with 5 round tact tables, which are arranged in the shape of a pentagon, and a centrally mounted turntable. Description: Turntable center = type Pentagon, diagonal 830mm; swing diameter Ø 873mm, side length 513mm 5x rotary indexing table, as a regular pentagon on machine body, center circle Ø = 1280mm, table shape truncated square 380x380mm, clamping device via 4 pieces make Röhm truncated cone clamping devices and 1 central centering flange, 360 ° rotatable, workpiece Ø approx. 730mm Actuation / drive is hydraulic * Nwsdpfxou N D S Uj Af Esn

Condition: refurbished (used), functionality: fully functional, load capacity: 8,000 kg, table height: 1,170 mm, table width: 1,700 mm, overall weight: 8,800 kg, Equipment: documentation/manual, Extremely compact rotary tilting table by PASSERINI with a 12.5 t load capacity. Refurbished machine (new electrical system including control cabinet, mechanics overhauled, newly painted). Complete and up-to-date documentation in German with EU Declaration of Conformity. The special feature of this machine is its very low overall height (faceplate height in horizontal position only 1,170 mm) and the far-rearward center of gravity. This allows for a very short design of the front outriggers, which on standard rotary tilting tables are often longer, thereby restricting access to the component and posing a tripping hazard. Nodpfx Afjxqg D Is Eswn Please note when comparing offers that we can also ensure long-term service and spare parts availability for the used machines we offer. This machine can also be rented prior to purchase. We offer attractive financing models (independent of banks). We are also happy to handle transportation for you.

Condition: excellent (used), functionality: fully functional, rotary table diameter: 600 mm, grinding height: 300 mm, disc diameter: 400 mm, grinding diameter: 600 mm, Manufacturer: ELB-SCHLIFF Model: SWR 50 T Completely overhauled: 2008 Delivery time: immediate Grinding area: Ø 600 x 300 mm Grinding wheels: max. Ø 400 x 100 x 127 mm Spindle taper: 60 mm Installation dimensions: approx. 2800 x 2800 x 2300 mm (L/W/H) Nwsdpfx Afeu Ed Nls Eon Total weight: approx. 5000 kg Control system: Siemens PLC

Condition: ready for operation (used), Year of construction: 2005, Immediately available from site: CNC Cylindrical Grinding Machine TOS HOL – MONTA Type UN 63 / 750 / 2000 Year of manufacture: 2005 CNC Control: Sinumerik 840 Di Centre height: 375 mm Grinding diameter: 750 mm Grinding length: 2000 mm Grinding wheel dimensions: 750 x 100 x 305 mm Nwsdsxqbftepfx Af Een Swing diameter in open steady rest: 40 – 250 mm Tailstock Morse taper: 6 Table swivelling: 4 degrees Workpiece spindle speed range: stepless, 1 – 50 rpm Grinding wheel speed: 20 – 33 m/sec Grinding spindle motor: 19 kW Total power requirement: 41 kW Workpiece diameter control Full enclosure Grinding mist extraction Weight: 20 t Complete accessories Price: EUR 28,500.— plus VAT, ex site

Condition: good (used), Year of construction: 2012, For sale are 2 identical injection molding machines of the company Netstal and the type SynErgy 2000-230/110 The machines were in production until the last day The company from which these machines originate attaches great importance to maintenance and servicing, which is why the machines are in very good condition 2 K function Turntable Designation Netsal SynErgy 2000 Year of construction 2012 Operating hours 28828 Weight 13300kg Clamping force in kN 2000 Injection unit 230 Machine drive 45 kW drive power Length 6901mm Width 2075mm Height 2240mm Cylinder size AG1 20mm / 32mm Available Cylinder sizeAG2 25mm / 32mm Available Nwsdpfxjkv Uq Ie Af Eon ____ Handling Wittmann, can be purchased additionally Serial number W833PRO - 0284 Operating hours approx. 13000h Year of construction 2016 Outfeed conveyor at the bottom Width 400mm Length 2300mm The systems can be purchased complete or in individual parts Machines already dismantled Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: new, Year of construction: 2025, Sturdy cast iron steel construction Large dimensioned milling unit made of cast iron, swivels up to -45° backwards Indication of the milling speeds by LEDs Fast, trouble-free speed change via eccentric voltage Nedpfx Asiidnfef Eswn Right-left rotation Display of height and inclination 1/10 mm accurate Milling fence in heavy professional design: with fine adjustment via toothed rack, with numerical display, aluminum stop jaws, 3-fold positionable for fast repetition of the adjustment TECHNICAL DATA Suction connection suction port diameter 2 x 120mm working table working table length 2500mm Working table width 655mm Electrical data Supply voltage 400V Mains frequency 50Hz Power drive motor 5,0kW Milling spindle spindle inclination 0 - -45 useful length of the spindle 125mm Spindeldrehzahl(en) 3500/6000/8000/10000min¯¹ spindle mandrel diameter 30mm Milling tool diameter max. tool diameter max. 240mm tool diameter max. lowerable 230mm tool diameter max. profile milling 210 - 240mm tool diameter max. tenon milling 320mm SUPPLY Aluminum milling stop jaws Arch milling protection hood Motorized height adjustable and swiveling milling spindle Digital display of the set values Speed display on the machine front via LED Table extension left and right Location: Ex stock 54634 Bitburg - immediately available -

Condition: used, Technical details: table length: 2000 mm Nedpfsu N Ebdox Af Eown table width: 1800 mm table load: 12,5 t table adjustment - longitudinal: 1250/1400 mm table rotating: 360 motorisch ° table positioning: 4x90 ° feeds - longitudinal: 0,63 - 2.000 mm/min. height over floor: 920 mm voltage: 380 V total power requirement: 6 kW weight of the machine ca.: 7,6 t machine dimensions LxWxH: 3,8 x 2,25 x 0,95 m Rotary table conventional Bohrwerkstisch konventionell, Bedienung über Schalttafel T-Nuten nach DIN 650: a=28mm; h=49mm; b=52mm; c=21mm *

Condition: refurbished (used), functionality: fully functional, load capacity: 8,000 kg, overall weight: 8,800 kg, height adjustment type: hydraulic, Equipment: documentation/manual, foot remote control, Extremely robust 3-axis rotary tipping table by TECNOMEC. Fully refurbished machine (new hydraulic pump and hoses, new electrics including control cabinet, overhauled mechanics). New paintwork upon purchase. Complete and updated documentation in German with EU Declaration of Conformity. This machine can also be rented prior to purchase. We offer attractive financing models (without bank involvement). We are happy to take care of the transport for you. Nsdexqgy Aopfx Af Eswn

Condition: good (used), -VERY LITTLE USED - CONTINUOUS POSITIONING AUTOMATIC DIVIDING TABLE TABLE CHUCK DIAMETER: 450 MM SPINDLE BORE 200 MM 4-axis Divisor/ index rotary table with equpmaint Manufacturer HAAS Nwjdpfxeuakrae Af Eon

Condition: excellent (used), Item description: Tsudakoma RNA‑251R 4-axis / CNC rotary table ----- Item condition: Nwedexpu D Hjpfx Af Ejn Item comes from a company liquidation. Good used condition. Internal number: H23

Condition: used, Year of construction: 2008, table diameter 1100 mm table load 1,2 t swivelling range 0 - 135 Grad turning speeds 0,15 - 3,4 U/min table height adjustment von 780 bis 1560 mm max. torque on the faceplate 1300 Nm Dimensions (LxWxH) 2,8 x 1,6 x 1,6 m Welding turntable with new remote control • Self-locking gear system, no pre- or post-running under eccentric loads • Hydraulic height adjustment allows for virtually unlimited positioning • Frequency-controlled, infinitely variable speed of the rotary table Nwsdpfx Aoxpi Akef Een

Condition: new, Year of construction: 2025, Woodworking machinesTable routers Minimax twf55 es Item number: 5502261 Sturdy cast steel construction Anodized aluminum sliding carriage Large dimensioned milling unit made of grey cast iron, swivels up to -45° to the rear Four milling speeds from 3500 to 10000 min¯¹ Right-left rotation as standard Height and inclination display accurate to 1/10 mm Fast and easy speed change via eccentric clamping Solid and precise cast iron table, stress relieved and re-annealed for lasting precision Powerful 5.0 kW industrial motor Curved milling hood included in delivery Made in Italy Dimensions and weights Length (product) approx. 1200mm width/depth (product) approx. 2000mm Weight (net) approx. 510kg Connection suction suction connection diameter 2 x 120mm Work table working table length 1200mm working table width 530mm table height 900mm sliding carriage length 1200mm Slide width 360mm Slide height 142mm Installation information Required space length 2800mm Space requirement width/depth 2910mm Explanation of space requirements The dimensions take into account maximum travels or useful lengths. Machine body length 1200mm Machine body width/depth 846mm Working area length 1600mm Working area width/depth 2300mm Explanation of working area Please add the dimensions given with the space requirement to obtain the free installation area recommended for the machine. Electrical data Supply voltage 400V Mains frequency 50Hz Power drive motor 5,0kW Milling spindle spindle inclination 0 to -45 useful length of the spindle 125mm Spindeldrehzahl(en) 3500/6000/8000/10000min¯¹ Milling spindle speed indicator LED on the front of the machine Nedpji Dphtjfx Af Ejwn spindle arbor diameter 30mm Milling tool diameter max. Tool diameter max. 240mm tool diameter max. lowerable 230mm tool diameter max. profile milling 240mm Tool diameter max. tenon milling 320mm EQUIPMENT Equipment Aluminum sliding carriage ✔ Milling fence Heavy-duty professional version with hold-down device, protective cover and aluminum milling fence jaws Telescopic miter fence with two folding stops Cantilever table ✔ Curved milling protective hood ✔ Eccentric clamp ✔ Handle on sliding carriage ✔ Height adjustment of the spindle manually Tilt adjustment of the spindle manual Control manual height and tilt adjustment of the milling unit Position of the control elements on the machine body location: ex stock 54634 Bitburg - immediately available -

Condition: used, Year of construction: 1975, Technical details: table diameter: 320 mm table height: 50 mm rotation movement: 360 Grad Njdpfsu Nkpmsx Af Eewn passage inside table: Ø 40 mm weight of the machine approx.: 73 kg space requirements of the machine approx.: L:0,63xB:0,53xH:0,14 m round table movement via manual wheel machine operation possible T-slot: 3x long and 1 x transverse - a=18mm - b=30mm - h=29mm - c=12mm *

Condition: used, functionality: fully functional, workpiece weight (max.): 10,000 kg, overall weight: 4,600 kg, Table size: 1500 x 1500 mm. Max. workpiece weight: 10.000 kg. Nedexphdyspfx Af Eswn Country of origin: Sweden. Weight: 4600 kg. With variable turning speed.

Condition: used, Year of construction: 2015, functionality: fully functional, DrillMatic TA325/P/H/12/2/1/-180° rotating hydraulic/pneumatic index table 400x620 Manufacturer: DrillMatic Nsdpfx Afeukg Sro Eewn Type: TA325/P/H/12/2/1/-180° Air connection: 4 ports. Index values: 3 4 6 8 12 Year of manufacture: 2015 Weight: 66 kg Table size: 400x620mm

Condition: excellent (used), Year of construction: 2004, Engel INSERT 330H/90 Controll: CC100 Condition: funtional Vertical machine with Horizontal injection Nwsdpfx Aeu Dbkdof Een Rotary table diameter: 1100mm Clamping force: 90 ton Opening max. : 570 Opening min. : 270 Platen size: 590x340 Screw: 40 mm Screw length: 160 mm Injection volume: 201 cm3 Injection pressure: 1230 bar Motor: 15 kw Weight: 5600 kg Height 2800 mm

Condition: good (used), Year of construction: 2002, functionality: fully functional, machine/vehicle number: 02020, We are selling a Delta LC400 rotary table surface grinding machine. Fully functional. Bearings and belts are new! Nwjdpfx Ajw A Rqxsf Een

Condition: as good as new (ex-display), Year of construction: 2025, CASADEI F 25 LL FK - table milling machine with tilting milling spindle and table extensions Table milling machine with tiltable milling spindle from -45° to +45 Sturdy cast steel construction Dynamically balanced milling unit anchored to the work table Particularly robust construction Smooth running due to precision aggregates and high dead weight Standard with right-left rotation and electronic blocking when changing direction 5 speeds from 3000 - 10000 min-1 Nwjdpfx Ajdqzcxef Ejn Speed change is easy and convenient from the machine side Standard with MK 4 change spindle system Large work table made of cast iron for long-lasting precision Easy handling due to control elements and speed display on the front of the machine Milling fence with fine adjustment and aluminum fence jaws as standard equipment Powerful industrial motors Equipment details: Fraes fence Fraes fence with crank/handwheel adjustment from the front side With numerical display Interchangeable spindle Interchangeable spindle MK 4 standard on all CASADEI F 23 and F 25 models Option sliding carriage Option sliding carriage for small tenoning operations and for slotting Scope of delivery: Manual tiltable milling spindle from +45° to -45°. Speed indication via LED at the front Aluminum stop jaws Sheet milling protection cover Right-left rotation of the milling spindle MK 4 interchangeable milling spindle Milling fence with crank/handwheel adjustment from the front with numerical display table extension left and right (2500 mm length) extendable workpiece support (2500 mm length) Model CASADEI F 25 LL FK article no. 5220728 Technical data Dimensions work table 2500 x 810 mm Milling spindle tilting range +45 to -45 degrees useful length of spindle at Ø 30-35 mm 140 mm useful length of spindle at Ø 40-50 mm 180 mm milling spindle stroke 90 mm max. tool Ø profiling 250 mm max. tenon tool Ø 350 mm max. milling tool Ø 160 mm max. tool-Ø lowerable 320 x 60 mm speeds, 5-stage 3000/4500/6000/ 8000/10000 min¯¹ motor power 400 V / 50 Hz / S6-40% 7 kW weight 480 kg suction nozzle-Ø stop 1 x 120 mm suction nozzle-Ø under table 2 x 80 mm Location: Ex stock 54634 Bitburg - immediately available -

Condition: used, Jaw chuck different versions Nwsdpfxsb I Sdxs Af Een from 300mm to 500mm